ASSALOY AH40R02 Wireless Communication Hub User Manual

ASSA ABLOY AB Wireless Communication Hub

User Manual

1ASSA ABLOY, the global leaderin door opening solutionsAperio® HubAH40 Installation Instructions
2AH40 - Table of ContentsAH40 - FCC and Industry Canada Statements 3AH40 - Placement of Communication Hub 4AH40 - Connectors 5AH40 - Jumpers 6AH40 - Communication Hub LED Indications 7AH40 - Technical Data 8ETL markingRecognized componentConforms to ANSI/UL standard 294, ANSI/UL 60950-1Certified to CAN/CSA standard C22.2 No. 60950-14002570For more detailed information about the Aperio system please read ST-001279-Aperio Technology Installation Guide AH40.
3AH40 - FCC and Industry Canada StatementsThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules and with RSS-210 of ISED. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:1. l’appareil ne doit pas produire de brouillage, et2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.The term “IC:” before the equipment certification number only signifies that the Innova-tion, Science and Economic Development Canada technical specifications were met.Le terme “IC” devant le numéro de certification signifie seulement que les spécifications techniques Innovation, Sciences et Développement économique Canada ont été respectées.FCC Caution: Any changes or modifications not expressly approved by the party respon-sible for compliance could void the user’s authority to operate this equipment.This radio transmitter (IC: 9504A-AH40R02) has been approved by ISED tooperate with the antenna types listed below with the maximum permissible gain indicated.Antenna types not included in this list, having a gain greater than the maximumgain indicated for that type, are strictly prohibited for use with this device.Antenna type: ASSA ABLOY AH-ANTENNA-1, max gain 2,15 dBi.Le présent émetteur radio (IC: 9504A-AH40R02) a été approuvé par ISEDpour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gainadmissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain estsupérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation del’émetteur. D’antenne énumérés: ASSA ABLOY AH-ANTENNA-1, Gain maximal indiqué 2,15 dBi.
4AH40 - Placement of Communication HubExample of placement of the Hub with 8 locks. AH40 can manage up to 16 locks. Note: AH40 Communication hub must be installed into a junction box ex European 2-Gang, Aperio bottom cover or with Americas adaptor plate to junction box. AH40 must be installed by qualified and trained personal. Indoor installation only! Note: The Aperio Communication hubs are not rated to be installed in the plenum space.< 15 m / ~ 50 ft
5AH40 - ConnectorsNote: When PoE (Power over Ethernet) is used, no power supply should be connected to J321. The installation must comply with national wiring regulations.ConneCtors DesCriptionJ201Ethernet connector. Connection to the Electronic Access Control system through a 10BASE-T / 100BASE-TX Local Area Network. Can also be used for power supply if connected to a IEEE 802.3af compliant Power Sourcing Device (PSE). Wire requirements CAT5 or higher.J321Power supply input, 8-24 VDC, 3.5 W. The power supply shall be a Limited Power Source (LPS) according to EN 60950-1. The power supply shall be 3 A over current protected. Wire requirements 16-22 AWG.8-24V- +LINK PAIRJ201J321ANTENNAEXT INT
6Jumpers DesCriptionANTENNA Select external antenna by connecting the two left pins.Select internal antenna by connecting the two right pins.PAIR Select pairing mode by connecting the two left pins.AH40 - JumpersNote: To install an external antenna use a thin screw driver and gently bend the antenna cap loose. Be careful, there are sensitive components behind the cap!8-24V- +LINK PAIRJ201J321ANTENNAEXT INT
7The Communication Hub has a status LED visible through the front cover. It supports optical schemes with red, green and yellow. The indication schemes are described by the figure below:AH40 - Communication Hub LED IndicationsNote: With the software tool Aperio® Programming Application and an USB radio dongle, further system installation parameters can be set.The “LINK” LED on the communication Hub indicates both status of the Ethernet Link level and if communication is ongoing. Note: LED on the Ethernet connector is not used.GreenOnlineGreen + OneRed FlashAperio® LockOfflineGreen + TwoRed FlashesEAC OfflineGreen + ThreeRed FlashesAperio® Lock andEAC OfflineYellow + Off,Fast FlashUHFCommunicationYellowPairing Active8-24V- +LINK PAIRJ201J321ANTENNAEXT INT
8Physical Dimensions 82 mm x 82 mm x 37 mm (H x W x T)Power Supply 8-24 VDC or Power over Ethernet (PoE)Power RatingPower supplyThe power supply shall be able to deliver minimum3.5 W. The power supply shall be 3 A over currentprotected. PoEIEEE 802.3af compliant class 1 Powered device (PD)Ethernet 10BASE-T / 100BASE-TX Local Area NetworkRadio StandardIEEE 802.15.4 (2400 – 2483,5 MHz) 16 channels (11-26) AES 128 bit encryptionReceiver Sensitivity -100 dBm Wireless Transmit Power10 dBm/MHz according to EN ETSI 300 328. Maximum spectral density.Wireless Operating Range Indoors up to 15 m / ~ 50 ft depending upon installed environment.Internal Antenna Two port cross polarized patch antenna.External AntennaOne reverse polarity SMA external antenna connector. AH40 is certified and is only allowed to be used with ASSA ABLOY external antenna AH ANTENNA 1. Operating Temperature 5 °C to 35 °CHumidity < 95 % non-condensingIP Classification IP20Safety and EmissionsFCC 47CFR Part 15 subpart B and subpart CIC RSS-GEN issue 5IC RSS-247 issue 2EN ETSI 301 489-1 v2.1.1EN ETSI 301 489-17 v3.1.1EN ETSI 300 328 v2.1.1EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013UL 294-2010C22.2AH40 - Technical Data
9NOTE
10NOTE
11NOTE
12www.assaabloy.com/aperioASSA ABLOY, the global leaderin door opening solutionsD000732307-F-US

Navigation menu