ASSALOY MODBLE9052 Bluetooth Smart Low Energy Radio Module User Manual 15 0143 Exhibit Cover
ASSA ABLOY Inc. Bluetooth Smart Low Energy Radio Module 15 0143 Exhibit Cover
ASSALOY >
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2738318 |
| Application ID | tRCXBN7fqZNKu26W9YYz4w== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 57.57kB (719596 bits) |
| Date Submitted | 2015-09-02 00:00:00 |
| Date Available | 2015-09-02 00:00:00 |
| Creation Date | 2015-09-02 14:56:59 |
| Producing Software | ScanSoft PDF Create! 7 |
| Document Lastmod | 2015-09-02 14:59:10 |
| Document Title | Microsoft Word - 15-0143 - Exhibit Cover.doc |
| Document Creator | Microsoft Word - 15-0143 - Exhibit Cover.doc |
| Document Author: | courtney.mcgann |
Certification Exhibit FCC ID: U4A-MODBLE9052 IC: 6982A-MODBLE9052 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-247 ACS Project Number: 15-0143 Manufacturer: Assa Abloy Inc. Model: BLE9052 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Manual Assa Abloy: Sargent Manufacturing and Corbin Russwin Factory Installation Instructions Factory Installation Instructions for P 1\2\WI1\IP1 reader assemblies Models BIKMPS, BIMPS, BCKMP and BCMP with Bluetooth Smart Model BLE9052 Assembly: 52-9052 RF Module. FCC Specific Statement: “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” General Statements (For all devices): Warning: Changes or modifications to this device not expressly approved by Assa Abloy could void the user’s authority to operate the equipment. Industry Canada Specific Statements: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio ex- 09/15 empts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 1 Users in the USA and Canada English: Operation is subject to the following two conditions: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure For Mobile Devices include the following: “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.” Pour les usagers résidant au Canada (French): L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Énoncé d’exposition à la radiation Pour les appareils mobiles sont les suivants: “Cet équipement est conforme aux limites d’exposition à la radiation RF FCC prévues pour un environnement non contrôlé. Cet équipement doit être installé et doit fonctionner avec une distance minimum de 20 centimètres des utilisateurs et des personnes Environnantes. Cet émetteur ne doit pas être colocalisées ou opérant en conjointement avec une autre antenne ou émetteur IC Detachable Antenna Statement: This radio transmitter Model BLE9052 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio Model BLE9052 a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur. The antenna type used on the Px BT LED Sounder board assembly: 52-9052 with antenna 52-4891 is of type: Dipole The antenna shall have an impedance of 50 ohms. The measured GAIN for the antenna to be utilized in the transmitter Model BLE9052 can be found in the table below: P1\P2\WI1\IP1 Model BLE9052 Assembly: 52-9052 BLE READER Frequency TRP (dBm) EIRP(dBm) Efficiency Antenna Gain (dBi) 2402 -6.85 -0.44 0.206538 -0.12 -0.32 2426 -6.05 0.49 0.248313 0.21 0.28 0.331131 0.35 1.05 2480 -4.8 1.4 52-4891 Gain Table: Model BLE9052 antenna 09/15 TX Power (dBm) Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 2 Assembly Drawings and Instructions: 52-4894TAB 52-4889 Factory Configuration Instructions: The assembly 52-9052-0000-000 P 1\2\WI1\IP1 BT shall be programmed at the manufacturing facility with firmware. The firmware version to be programmed into the unit shall be V5.09, which applies an advertising rate of 20ms and a RSSI tap sensitivity of -55dB. 09/15 Field Configuration Instructions: At the customer site, encryption keys are loaded by a “Mobile Keys” certified technician using an HID configuration card. This installation can be performed on mobile enabled readers only. Once the “Mobile Keys” have been loaded interface with mobile devices can be achieved. The HID BLE Configuration application is currently available on Android OS and provides additional configuration that can be used to configure tap sensitivity and transmission power. Transmission power is restricted to a maximum of 0dBm. The HID BLE Configuration application can be used to upgrade the BLE devices firmware using the OTA technology. Field firmware upgrades can only be performed through and HID certified technician that are authorized to use a controlled administration card. Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 3 09/15 Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 4 09/15 Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 5 09/15 Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 6 09/15 Copyright © 2015, ASSA ABLOY Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Inc. is prohibited. BTMN2A • PAGE 7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Page Count : 8 XMP Toolkit : 3.1-701 Producer : ScanSoft PDF Create! 7 Creator Tool : Microsoft Word - 15-0143 - Exhibit Cover.doc Create Date : 2015:09:02 14:56:59-04:00 Modify Date : 2015:09:02 14:59:10-04:00 Title : Microsoft Word - 15-0143 - Exhibit Cover.doc Creator : courtney.mcgann Author : courtney.mcgannEXIF Metadata provided by EXIF.tools