ASSALOY PRXTRMH1 PROXIMITY CARD READER User Manual Appendix D Schematics

Download:
Mirror Download [FCC.gov]
Document ID	833448
Application ID	2xbfaPP8v44rZYAdIZHong==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	52.21kB (652647 bits)
Date Submitted	2007-08-24 00:00:00
Date Available	2007-08-27 00:00:00
Creation Date	2007-03-23 11:28:51
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2007-07-05 10:23:37
Document Title	Microsoft Word - Appendix D_Schematics.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	donna3

FCC ID: U4A-PRXTRMH1
IC ID: 6982A-PRXTRMH1
Report No. M060902_Cert_Rx
EMC Technologies Report Number: M060902_Cert_Rx
APPENDIX G
USER MANUAL
EMC Technologies Pty Ltd – 176 Harrick Road, Keilor Park VIC 3042 Australia
www.emctech.com.au
Installation Instructions For
© SARGENT Manufacturing Company 2007
Harmony Series
H1 Mortise Lock
A7877A
03/07
Table of Contents
Page
Warning
General Description.....................................................1
Specifications............................................................1
Features ..................................................................1
Parts Breakdown .......................................................2-3
Installation Instructions ..............................................4-11
Operational Check ......................................................12
1 Warning
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.
Harmony Series H1 Mortise Lock
2 General Description
The SARGENT Harmony Series H1 Mortise Lock is designed to interface with an existing weigand access
control system.
3 Specifications
•
•
•
•
Latch - Stainless steel 3⁄4" projection one-piece
Deadbolt - One-piece hardened stainless steel
Guardbolt - Stainless steel, non-handed
Handed - Easily field reversible without
opening case
• Case - 12 gauge heavy duty wrought steel
• Outside lever controlled by any prox credentials
• Inside lever provides REX signal and retracts latch
and deadbolt
• Locks furnished for 1-3/4" doors. Can be
furnished for other door sizes upon request.
Consult factory
• U.L. Listed (3 hr.)
4 Features
• Complete monitoring of door from locks
• Wires directly to Access Control System
• 12 or 24 VDC Fail Safe/Fail Secure
• HID 125khz proximity credentials
• All HID Bit formats
Wiegand
Access Control
System
(By Others)
Power
12VDC or 24VDC
Harmony Series
H1
A7877A
© SARGENT Manufacturing Company 2007
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
5 Parts Breakdown
22
23
21
20
15
24/25/26
31
30
14
27
28
29
34
33
10
10
11
12
13
18/19
32
29
16/17
27
28
© SARGENT Manufacturing Company 2007
A7877A
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
5 Parts Breakdown (Continued)
ITEM
PART No.
DESCRIPTION
REQ’D
15
10
11
12
13
14
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
52-5188
52-5189
52-5184
52-5185
52-0798
Outside Escutcheon Reader Assembly w/Cylinder
Outside Escutcheon Reader Assembly w/o Cylinder
Inside Escutcheon Assembly w/Turn
Inside Escutcheon Assembly w/o Turn
Mounting Plate - Mortise
Reference Harmony Series catalog for available lever handles
82-0347
82-0614
82-0368
81-0723
01-0079
82-3082
82-0184
82-3088
01-1495
82-0081
82-0084
77-1467
01-1218
01-4577
01-1028
01-1472
01-1174
82-0995
01-2299
01-1019
01-1028
52-0796
52-0795
82-4576
82-0691
82-4577
Reference Harmony Series catalog for available Rose styles
Inside/Outside Spring
Spindle Anchor
Inside/Outside Spindle
Mounting Post
Washer
Plate Assembly
Cap Nut
Inside Spindle Adapter and Plate Assembly
Screw #8-32 x 1/2"
Lock Body Assembly w/Dead Bolt - 82280-82283 12/24V Functions
Lock Body Assembly w/o Dead Bolt - 82270-82273 12/24V Functions
Face Plate w/o Dead Bolt
Face Plate w/ Dead Bolt
Through-bolts #8-32 x 2" Phillips Flat Head Screw
Wood Screw #6 x 3/8" Phillips Flat Head
Escutcheon Screw #8-32 x 5/8" Phillips Flat Head
Escutcheon Screw #8-32 x 1/4" Phillips Flat Head
Lever Handle Screw, A, E and F Lever
Lever Handle Screw, B, J, L, P and W Lever
Lever Handle Screw - Studio Collection
Lock Body Screw - Wood Door #12 x 1 1/4"
Lock Body Screw - Metal Door #12-24 x 1/2"
Face Plate Screw Machine - #8-32 x 1/4"
Gasket Harmony Outside - Mortise
Gasket Harmony Inside - Mortise
Adapter and Plate Assembly (DL)
Bushing Outside (DL)
Inside Adapter Plate and Bushing Assembly (DL)
A7877A
© SARGENT Manufacturing Company 2007
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
6 Installation Instructions
Verify Hand and Bevel of Door
Step #1 – Door Preparation
Before Starting
Wood door - A7879 template ships with product. For replacement
template, contact SARGENT (4541 for raceway, wood and metal door)
Metal door - 4590 for Locks With Deadbolt
Outside
of door
Inside
of door
Raceway for
network/power cable
(ELynx) 12 Conductor
Thru-bolt hole
2 places
Hole for cable from
Reader to controller board
Pre-drilled and/or
Tapped holes 2 places
Inside cylinder hole
Outside cylinder hole
76/78 functions only
Thumb turn hole
Lever handle hole
Lever handle hole
Mortise area
Pre-drilled and/or
Tapped holes 2 places
© SARGENT Manufacturing Company 2007
A7877A
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
Step #2 – How to Reverse Lock Hand
Note: Red surface of locking piece must face secure side of door.
To rotate locking piece:
1. Position lockbody with red surface of locking piece visible
2. Insert blade type screwdriver into locking piece slot to rotate
locking piece
3. Push locking piece toward back of lock body and rotate 180°
until RED surface shows on opposite side
4. Red indicates locked (outside) side.
5. Wire harness MUST exit thru non-cylinder side.
Connector
Connect
Connector
Locking
guide slot
Push in
Right hand
shown
Red color
locking piece
indicates locked side
Locking
guide slot
Push in
End C
End Cap
Right hand
shown
Red color
Red color
locking piece
locking piece indicates locked side
indicates locked side
Note: Beveled surface of latch must face strike.
The deadlatch is self adjusting. To change hand of latch:
1. Insert screwdriver blade into the spade shaped slot
2. Rotate screwdriver 90º to push latch out until back of latch
clears lock front. Then rotate latch 180º.
Latch will then re-enter lockbody.
(Note: Latch can not be unscrewed)
Connector
and wires
Connector
and wires
End
cap
Triangular
slot
Triangular
slot
Latchbolt
Front
End
cap
End
cap
Latchbolt
Deadbolt
Front
Deadbolt
Latchbolt
Latchbolt
Dead latch
Rotate
Rotate
Dead latch
Outside of
door
Outside of
door
A7877A
Outside of
door
© SARGENT Manufacturing Company 2007
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Co
and
Harmony Series H1 Mortise Lock
Step #3 – Lockbody Installation
Wires and connector go into the mortised
area and out of the inside cylinder hole
Must feed
connectors and
wires thru
non-cylinder
side
(2)#12-24 x 1/2" long
flat head screws
for metal doors.
Inside of
door
Step #4 – Inside Mounting
Plate Installation
(2)#12 x 1=1/4" long
flat head wood screws
for wood doors.
1. Secure the mounting plate with (4) self tapping
screws (#8 x 1/2").
1/8" Dia hole
4 required
Self tapping screws
#8 x 1/2" long for
wood and metal doors
4 required
Inside of
door
© SARGENT Manufacturing Company 2007
A7877A
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Profile Series H1 Mortise Lock
Step #5 – Installation of Outside Escutcheon Reader & Lever Assembly
1. Feed the reader cable connector located on the back of the outside escutcheon from the outside of door
through door.
2. Securely tighten the outside escutcheon with (2) through-bolts (#8-32 x 2") Phillips flat head screws with the
mounting plate.
3. With outside lever horizontal, insert the mounting post through outside of door and lock body. Make certain
the lever spindle is proper engaged in lock.
4. On the inside of the door, insert spindle into square hole of mortise lock.
5. Slide inside adapter and plate assembly over spindle and loosely secure with (2) screws (#8-32 x 5/8"). Do not
tighten completely, cylinder should be installed prior to tightening.
Note: For 82276 & 82278, thread cylinder through escutcheon and into the lockbody.
Escutcheon Screws
#8-32 x 2" long
Phillips Flat Head
Gasket Outside Harmony - Mortise
Reader Cable
#8-32 x 5/8"
Machine Screws
From Reader Board
P5 to J5
J5
To E-Lynx
Harness
J4
From Lock Body
P4 to J4
J3
From Lock Body
P3 to J3
Step #6 – Connector Attachment
1. Securely tighten lockbody screws on the edge of the door and
then securely tighten the thru bolt screws.
2. Connect P3 (2 Pin Connector) from lock body to J3 on Interior
Escutcheon PCB Assembly.
3. Connect P4 (5 Pin Connector) from lock body to J4 on Interior
Escutcheon PCB Assembly.
4. Connect P5 (7 Pin Connector) from Reader board to J5 on
Interior Escutcheon PCB Assembly.
5. Connect E-Lynx Harness (4 Pin & 8 Pin) from door harness to
E-Lynx harness on Interior Escutcheon PCB Assembly.
6. Place extra wire inside door hole
NOTE: Connectors go on only one way. Do not offset connector
and be sure they are completely seated.
A7877A
© SARGENT Manufacturing Company 2007
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Profile Series H1 Mortise Lock
Step #7 – Installation of Inside Escutcheon Assembly
1. Attach E-Lynx door harness connectors to inside electronic.
2. Feed wires into door pre.
3. Attach inside escutcheon to mounting plate.
Note: Be sure not to pinch wires when mounting escutcheon.
E-Lynx Harness
Gasket Inside Harmony - Mortise
Escutcheon Screw
8-32 x 5/8"
long Phillips
Flat Head
Escutcheon Screw
8-32 x 1/4"
long Phillips
Flat Head
OUTSIDE OF
DOOR
INSIDE OF
DOOR
© SARGENT Manufacturing Company 2007
A7877A
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
Step #8 – Stallation of the Inside Rose and Inside Lever Assembly
1. Rotate inside rose clockwise.
2. Slide lever handle onto spindle until fully
seated. Be sure handle is horizontal and
facing to the rear of the door.
3. Tighten the set screw securely with
1/8" hex wrench.
Rose
Set Screw
Inside Lever
Spindle
Inside of door
Step #9 – Installation of Outside Cylinder
Fig. 1
Fig. 2
1. Verify orientation of cylinder (Ref. to Fig. 3).
2. Tighten the cylinder clamp screw to prevent unscrewing of the cylinder (Ref. Fig. 2).
3. Test cylinder function: 78 Function - Key retracts latch 76 Function - Key retracts latch and projects and
retracts deadbolt.
EN
Note: Key and
cylinder must be
rotated as shown
SA
RG
SARGENT
Correct
90 1/8 Cylinder Ring
Set Screw
Incorrect
Fig 3
Type 43 Mortise
Cylinder only
Phillips
Screwdriver
Fig 1
Fig 2
A7877A
© SARGENT Manufacturing Company 2007
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
Step #10 – Application of Front Plate
1. Attach front plate with (2) flat head screws.
Lock Body Screw
Flat Head Screw
2 Req'd
Lock Body Screw
© SARGENT Manufacturing Company 2007
10
A7877A
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
Harmony Series H1 Mortise Lock
7 Mechanical Operation Check
For 82276 & 82278 Function mortise locks with cylinders:
1. Insert key into cylinder and rotate (There should be no friction against lock case,
wire harness or any other obstructions. Refer to Section 6, Step 8 if harness
friction exists).
2. The key will retract the latch. Key should rotate freely.
3. If the deadbolt is thrown, the key will retract both the deadbolt and the latch.
4. Inside lever retracts latch and deadbolt (if provided).
A7877A
© SARGENT Manufacturing Company 2006
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
11
Founded in the early 1800’s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products
and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes
commercial construction, institutional, and industrial markets.
© SARGENT Manufacturing Company 2007
ASSA ABLOY is the world’s leading manufacturer and supplier of locking solutions,
meeting tough end-user demands for safety, security and user friendliness.
An ASSA ABLOY Group company
A7877A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 15
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a1c5dd88-0a52-48ca-8320-3584dfe87c26
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2007:03:23 11:28:51+11:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:07:05 10:23:37+10:00
Metadata Date                   : 2007:07:05 10:23:37+10:00
Document ID                     : uuid:dbe23661-f135-4a7b-86a4-ae7de8444a85
Format                          : application/pdf
Title                           : Microsoft Word - Appendix D_Schematics.doc
Creator                         : donna3
Author                          : donna3

EXIF Metadata provided by EXIF.tools