ASSALOY SCYICLS2 Microprocessor Controlled Networked Locks User Manual XX XXXX Exhibit Cover

ASSA ABLOY Inc. Microprocessor Controlled Networked Locks XX XXXX Exhibit Cover

UserManual.wiki >

SCYICLS2 User Manual >

Contents

P1 Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-SCYICLS2 IC: 6982A-SCYICLS2 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-0071.W06.11.A Manufacturer: Assa Abloy, Inc. Model: P1-IM/IKM Manual

A8032D12/10Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. PASSPORT 1000Mortise LockInstallation InstructionsP1PRELIMINARY

1-800-810-WIRE • www.sargentlock.com • A8078A Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.10/10/10Warning !1Observe precautions for handling electrostatic sensitive devices.1234567 Table of ContentsWarning ...................................................................................2General Description .................................................................3Hardware Speciﬁcations .........................................................3Electronic Speciﬁcations .........................................................3Installation Wiring Overview ...................................................3Installation Wiring ...................................................................4Parts Breakdown .....................................................................7Installation Instructions ..........................................................7Operational Check ................................................................1789Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Warning SARGENT Mfg. Co. v.P Series locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications.FCCThis equipment has been tested and found to comply with the limits for a Class A digital device, pur-suant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Industry Canada: The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁcations were met.This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harm-ful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Cet appareillage numérique de la classe A répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 3Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock Installation Wiring Overview5General Description2Hardware Specifications3• Inside lever retracts latch• Locks furnished for 1-3/4” doors only• Grade 1; UL Listed• Outside lever controlled by any combination of keypad, magnetic keypad, iCLASS, prox (prox-imity) reader, or mechanical cylinder • Complete locksets with on-board memory• Magnetic swipe standard with optional 125 kHz Proximity Reader (specify PRX-), 13.56 MHz reader (specify IKM-), and/or keypad (specify KP-)• ADA Compliant• Easily retroﬁts existing Passport 1000 door preps (cylindrical locks)• Latch 1/2” standard 3/4” throw ﬁre-rated double doors (optional) (41- preﬁx)• Guarded latch• Outside lever is unlocked through access control credentials onlyElectronic Specifications4• 2,400 users per lock; 10,000 event audit trail• Multiple time zone and holiday access scheduling• Centralized lock management • Real time door status monitoring• First-In unlock conﬁguration, either by time or by user (selectable)• Lock down capable• Input Power: PoE Class 2 Device, as deﬁned by IEEE 802.3af, requires up to 7 watts over structured cabling• Uses existing Magstripe keycards (track 2)• Magnetic Stripe Card Coercivity: HiCo (4000 Oersted) or LoCo (300 Oersted)• Supports HID 125 kHz prox or 13.56 MHz iCLASS credentials (26 - 39 bit); supports CSN reads for other common 13.56 MHz cards, including MiFare, DesFire, and FelicaThe SARGENT Passport Series v.P1 cylindrical lock is available with either an HID® Prox 125 kHz or 13.56 MHz iCLASS® technology reader. It utilizes existing infrastructure and IEEE 802.3af PoE (Power over Ethernet) providing access control with Magnetic swipe and optional Proximity Reader and/or Keypad, as well as detailed audit capabilities-technology as a proven alternative to traditional access control installations. The v.P1 is a self-contained microproces-sor-controlled access control product with non-volatile memory. It uses the existing network cable to communicate with access control systems. The v.P1 lock holds a total of 2400 different user codes. Using PoE technology coupled with third party software, this v.P1 online lock offers a complete, integrated access control system.The Passport Series v.P1 cylindrical lock may be used for both indoor and outdoor applications. A weather- protective gasket is recommended for outdoor applications. HID and iCLASS are registered trademarks of HID Global Corporation.* Lockdown and real-time door status monitoring available only when lock is hard-powered SARGENT Passport Series PoE v.P1 Typical ApplicationLMT: Lock Management ToolA. PoE frame harness assemblyB. PoE data hinge from McKinney (patent pending)C. PoE door harness* from McKinneyD. DPS: Door Position Switch (Cylindrical and Exits only)E. Passport Series v.P1 PoE Lock * Door width determines lengthNetwork CableNetwork Switch (802.3af) Surface Mount RJ45 ABCDESupplied by OthersPRELIMINARY

4 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock Installation Wiring6JST4-PinMolex-F Molex-F Molex-MCable: CAT 5e,26 AWG stranded,shielded, 100ohmRJ45-M Molex-MCable: CAT 5e or higher24 AWG shielded, 100ohmB-Splice Crimp ConnectorPoE LockCeilingSupplied by CIGroundRing Terminal Secured to Lock Mounting Plate4-Pin MolexA. PoE Frame harness assembly (From McKinney)B. PoE data hinge (Patent Pending) (From McKinney)C. PoE Door harness* D. Passport 1000 Online P1 PoE Lock * Order of installation may vary. Refer to appropriate sections for instructions.Frame-SideHarnessAssembly(15' length)24AWG Stranded Drain Wire for Earth Ground in 15' Frame HarnessCable drain wire concealed in shrink tubingPatch PanelDrain Wire Terminated on RackCable: CAT 5e or higher24 AWG shielded with drain wireRJ45-F Jack Approved SoftwareCertiﬁed Integrator (CI) supplies and terminates the B-Splice connector and the Male RJ45 connector from harness to end user provided facility cableSupplied by End UserPoE SwitchDrain WirePoE Switch isTerminated toEarth GroundPatch Cable Patch Panel to PoE SwitchWiring to TIA-568-B StandardANotes:• Connectors go on only one way. They cannot be placed in an incorrect position. • Do not force and do not offset connectors.• Be sure they are com-pletely seated (ﬂush).BCDPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 5Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock Components and wire harness supplied by McKinney: Suggested installation. RJ45-M Molex-MCable: CAT 5e or higher24 AWG shielded, 100ohmB-Splice Crimp ConnectorCeilingSupplied by CICut end / ceiling-side PoE harness: TIA/EIB-568-B Standard Wiring1 2 3 4 5 6 7 8Pair Number Wire PIN1 White/Blue White/Blue 5Blue 42 White/Orange White/Orange 1Orange 23 White/Green White/Green 3Green 64 White/Brown White/Brown 7Brown 8Do not confuse pair numbers with pin numbers. A pair number is used for reference only (eg: 10BaseT Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack.Frame-SideHarnessAssembly(15' length)24AWG Stranded Drain Wire for Earth Ground in 15' Frame HarnessCable drain wire concealed in shrink tubingAFrame Harness Installation1. Feed cut end of harness into hole on hinge-side through single access hole. 2. Push one connector back through the hole and feed into the other access hole.Each of the hinge-side harness connectors should end up threaded through a different access hole and matched to the same size pin connector from the door harness:• 4-pin male molex connector.• 6-pin male molex connector with ground wire.Hinge side of PoE harness:6-pin F4-pin M6-pin M4-pin FFrame PoE Hinge (Patent Pending)PoE Data HingeHinge-side harness connectors:• 4-pin male molex connector• 6-pin male molex connector with ground wireLock-side harness connectors:• Ring terminal• (2) 4-pin connectors BInstallation Wiring (Continued)PRELIMINARY

6 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock Order of installation may vary. Refer to appropriate sections for in-structions. 1. Prop door open.2. Tape the two lock-side 4-pin connectors to the ring terminal.3. Using the ring terminal, carefully ﬁsh the assembly through the door channel to the lock. 4. Remove tape from ring terminal and door harness connectors. Hinge-side harness connectors:• 4-pin male Molex connector• 6-pin male Molex connector with ground wire Lock-side harness connectors:• Ring terminal• (2) 4-pin connectors:• 4-pin Molex connector• 4-pin connectorNotes:• Connectors go on only one way. They cannot be plugged to incorrect position. • Do not force and do not offset connectors.• Be sure they are completely seated (ﬂush).Order of installation may vary. Refer to appropriate sections for instructions. Hinge-side harness connectors:• 4-pin male Molex connector• 6-pin male Molex connector with ground wireLock-side harness connectors:• Ring terminal• (2) 4-pin connectors:• 4-pin Molex connector• 4-pin connectorNotes:• Connectors go on only one way. They cannot be plugged to incorrect position. • Do not force and do not offset connectors.• Be sure they are completely seated (ﬂush).PoE Data HingePoE LockJST4-Pin4-pin M 4-pin F4-pin F4-Pin Molex6-pin F 6-pin F 6-pin MCable: CAT 5e,26 AWG stranded,shielded, 100ohmDrain WirePoE Door HarnessCDPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 7Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock Parts BreakdownP1 PoE Lock with Magnetic Card Swipe With or Without Keypad891012131012467P2355Inside1011Outside58Inside 91012131012467P2355Inside1011Outside5891110121314Outside ITEM No. PART No. DESCRIPTION1 52-0757 Lens (Cliplite)252-0738 Outside Passport Escutcheon Only (Magnetic Swipe and Keypad)52-0739 Outside Passport Escutcheon Only (Magnetic Swipe)3 52-0760 Light Pipe (Cliplite)4 52-3593 Slim Style Keypad Assembly5 01-9299 #4-40 x 3/16” Phillips Pan Head Screw6 52-3591 Swipe Reader Assembly7 52-0745 Online Interface PCB8 52-3209 Harness Assembly9 52-0748 Inside Mounting Plate10 77-0168 #8-32 x 1-7/8” Phillips Flat Head Screw11 01-1146 #8-32 x 3/8” Phillips Flat Head Screw01-1176 #8 x 3/8” Phillips Flat Head Wood Screw12 52-4246 Modular Component13 52-3592 Inside Escutcheon Assembly14 01-4421 #8-32 x 1/2” T-20 Torx Pan Head ScrewPRELIMINARY

8 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock P1 PoE Lock with Magnetic Card Swipe , 125 kHz Prox and Keypad91012131012467P2355Inside1011Outside58123437956383InsideOutside1011ITEM No. PART No. DESCRIPTION1 52-1103 Outside Passport Escutcheon only (Magnetic Swipe, Keypad and Proximity Reader)2 52-3593 Slim Style Keypad Assembly3 01-9299 #4-40 x 3/16” Phillips Pan Head Screw4 52-4243 Swipe Reader Assembly5 52-1106 Prox Reader Gasket6 52-4206 Antenna Assembly7 52-0745 Online Interface PCB8 52-3209 Harness Assembly 9 52-1109 Back Plate10 52-0748 Inside Mounting Plate11 77-0168 #8-32 x 1-7/8” Phillips Flat Head Screw12 01-1146 #8-32 x 3/8” Phillips Flat Head Screw01-1176 #8 x 3/8” Phillips Flat Head Wood Screw13 52-4246 Module Assembly14 52-3592 Inside Escutcheon Assembly15 01-4421 #8-32 x 1/2” T-20 Torx Pan Head ScrewParts Breakdown (Continued)PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 9Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock Parts Breakdown812345104449876Magnetic Card Swipe With 13.56 MHz iCLASS and Keypad4ITEM No. PART No. DESCRIPTION1 52-4402 Outside Mask Assembly 2 52-1255 Outside Escutcheon - iCLASS3 52-3593 Slim Style Keypad Assembly4 01-9299 #4-40 x 3/16” Machine Screw5 52-4243 Swipe Reader Assembly6 52-4401 iCLASS Module Assembly 7 52-3209 Harness Assembly8 52-4410 iCLASS Harness9 52-1109 Back Plate10 01-9300 #4-32 x 5/16” Plastite ScrewPRELIMINARY

10 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock 8200 Series Mortise LockITEM PART No. DESCRIPTION1 See catalog #41 Cylinder (1-1/8” Minimum Length)2 13-0140 Cylinder Compression Spring3 See catalog 1KB-1 Cylinder Rosette4 See catalog Mortise Lockbody5 77-2592 130 KB Thumbturn for Deadbolt Functions Only6 See catalog Inside Lever Handle7 See catalog Outside Lever Assembly8 82-0368 Spindle9 82-3088 Inside Lever/Knob Adapter Plate Assembly10 01-1495 #8-32 X 5/8 Machine Screw11 82-0612 Non Loosening Wave Washer12 See catalog Mortise Rose13 82-0347 Spindle Spring14 01-1019 #12-24 X 1/2” Machine Screw15 01-2299 12 X 1-1/4 Wood Screw16 82-0578 Outside Front Plate (Electrical, Latchbolt & Guardbolt)82-0579 Outside Front Plate (Electrical, Deadbolt, Latchbolt and Guardbolt)17 01-1028 #8-32 X 1/4 Machine Screw56789101112131415 16 1743PRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 11Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock 1 Door PreparationInstallation Instructions9Left HandHinges Left.Open Inward.“LH”Left HandReverse BevelHinges Left.Open Outward“LHRB”Right HandHinges Right.Open Inward.“RH”Right HandReverse BevelHinges Right.Open Outward.“RHRB”A. Verify Hand and Bevel of Door• (KP-) P1- (PRX- or IKM) 82276 x Rose & Lever x Finish x Hand• (KP-) P1- (PRX- or IKM) 82277 x Rose & Lever x Finish x Hand• (KP-) P1- (PRX- or IKM) 82278 x Rose & Lever x Finish x Hand• (KP-) P1- (PRX- or IKM) 82279 x Rose & Lever x Finish x Hand Note: KP- is for the optional Keypad and PRX- is for the optional Proximity Reader• (IKM-) P1- (PRX) 10G77 x Rose & lever x Finish x Hand Note: IKM- is for the 13.56 MHz Reader optionB. Verify Product LabelC. Door Preperation• Field template: A7950 for wood and metal doors.• Door manufacturers template: 4651.Outside of Door Inside of DoorThrough Bolt HolesInside Mounting Plate Mounting HolesController CutoutThumb Turn Location(Deadbolt Functions Only)Lever Handle HolesThrough Bolt HolesController CutoutCylinder HoleLever Handle HolesMortise Pocket(8200)Raceway for PowerRaceway for PowerPRELIMINARY

12 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock 2 How to Change Hand of LockbodyA. Reverse Lock HandRed surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1. Position lock body with red surface of locking piece visible.2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3. Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody.Inside of DoorPlastic Retaining RingConnectorRing TerminalSlotB. Retaining RingMake sure the plastic retaining ring is seated cor-rectly (Fig. 2B):1. The wires and the plastic retaining ring must be located on the non-cylinder side. 2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole.3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring. Locking SlideRed on locked side Push InFig. 2ARight HandLock ShownBeveled surface of latchbolt must face strike. The deadlatch is self adjusting. To change the hand of the latchbolt:1. Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch.2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody.Note: Latch cannot be unscrewed.C. Reverse Latch HandLatchbolt(2) #12-24 x 1/2” LongFlat Head Machine Screw for Metal DoorsPRELIMINARY

14 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock 5 Install Inside and Outside Levers6 Deadbolt Functions Only (82276 & 82277)1. Insert alignment tool (supplied) into lock body thumb turn.2. Slide back plate over tool and make level.3. Secure back plate to door with two (2) #6 x 3/8” round head wood screws or #6-32 x 3/8” round head machine screws.4. Dispose of tool, position thumb turn over back plate (Fig. 6A) and secure with #6-32 x 1/4” ﬂat head screw.Note: Thumb turn should cover screw head when deadbolt is retracted.Refer to instructions (A5675G) included in package included with lock.1. Slide the outside lever and spindle assembly through the door and lockbody.2. Using the inside adapter plate and spindle, secure loosely with (2) #8-32 screws.Note: Position threaded hole on the inside adapter to align with lever hole.3. Tighten the lockbody screws on edge of door. 4. After the lockbody screws are tightened, tighten both inside adapter screws.5. Position and attach rose over inside adapter. 6. Position and secure inside lever to the inside adapter with set screw.Fig. 5AMortise Lock BodyConnector and Ground Ring TerminalOutside Lever AssemblyInside Adapter PlateRosePoE CablesInside LeverBack Plate#6 x 3/8” Round Head Wood Screws#6-32 x 3/8" Round Head Machine Screws#6-32 x 1/4" Flat Head ScrewThumb TurnFig. 6B DetailPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 15Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock 7 Install Gasket (Optional)Note: Optional, for non-ﬁre rated doors only.For non-ﬁre rated door applications, an optional gasket may be used as a weather seal between the escutcheon and the outside door surface.Peel off adhesive backing and attach to outside escutcheon.Fig. 7AOutside Passport TrimGasket8 Install Outside Escutcheon and Mounting Plate Assembly1. Insert the mounting posts through holes as shown.2. On the inside of the door, position the mounting plate over the indicated holes.3. Feed PoE and reader cables through side opening (Fig. 8A). Cable from lockbody feeds from bottom (Fig. 8A and 8B).4. Attach 2 ground ring terminals, one from controller and one from lock body to bottom right corner using one #8-32 x 1-7/8” ﬂat head machine screw. Make sure they are positioned upright (Fig. 8A).5. Insert other three #8-32 x 1-7/8” ﬂat head machine screws and tighten, fastening the outside escutcheon to the door (Fig. 8B).IMPORTANT: If the following step is skipped, the product will not be UL-compliant:6. Attach two (2) #8 x 3/8” ﬂat head wood screws for wood doors or (2) #8-32 x 3/8” ﬂat head machine screws for metal doors (Fig. 8C).(4) #8 - 32 x 1-7/8” Flat Head Machine ScrewsMounting PlateFig. 8BAttach ground wires to bottom right screwaOutside Passport TrimPoE Reader CablesFig. 8C(2) #8 - 3/8” Flat Head Wood Screws OR(2) #8 - 3/8” Flat HeadMachine Screwsedcb(2) 4-Pin PoE connectorsedbc24-pin from reader10-pin from lock bodyaGround wires and PoE and Lock body harnessesReader cable (iCLASS only)fReader cable (iCLASS only)fReader cable (iCLASS only)Controller / ReaderCablesLockbody CablesLock Ground Position ground ring terminalupright, thentighten screw. Reader cable (iCLASS only)PRELIMINARY

16 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock 9 Install Inside Module Component Assembly Insert bottom of Module Component Assembly ﬁrst (Fig. 9A), then clip top of Assembly to backplate, verifying both tabs attached securely.Outside of DoorFig. 9ATabsDetail 10B(2) 4-Pin PoE connectorsedbc24-pin from reader10-pin from lock bodyedcb10 Attach Connectors Secure the following connectors onto the circuit board (Fig. 10A and 10B):1. Secure the 10-pin lock body assembly connector (e).2. Secure the 24-pin keypad/card reader connector (d).3. Secure two 4-pin PoE connectors (b and c). 4. Secure the iCLASS reader cable (f). Route wires from behind backplate through battery com-partment. Notes: • Connectors go on only one way.• Do not force and do not offset connectors.• Be sure the connectors are completely seated (ﬂush).f9-pin reader cable (iCLASS only)fPRELIMINARY

12/15/101-800-810-WIRE • www.sargentlock.com • A8032D 17Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Passport 1000 Series P1 PoE Mortise Lock 11 Install Inside Escutcheon1. Position inside escutcheon as shown (Fig. 11A).Verify that all wires are positioned within the escutcheon to avoid pinching.2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan head screws.3. Straighten escutcheon and tighten securely.DO NOT OVERTIGHTEN.Fig. 11A(2) #8-32 x 1/2” Torx ScrewsAttach front plate with (2) #8-32 X 1/4” ﬂat head screws (Fig. 12A).12 Attach Outside Front PlateFig. 12A(2) #8-32 x 1/4” Flat Head ScrewsPRELIMINARY

18 1-800-810-WIRE • www.sargentlock.com • A8032D Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.12/15/10Passport 1000 Series P1 PoE Mortise Lock Operational Check9IMPORTANT: Be sure to test functions prior to closing door.In all cases, perform the following checks:1. Ensure that inside lever retracts latch (and deadbolt for dead-bolt functions).• For units with cylinders, the following checks apply:Insert key into cylinder and rotate:a. There should be no friction against lock case, wire harness, or any other obstructions. If friction or bind-ing occurs, re-adjust cylinder and wiring harness to eliminate issues.b. The key should retract the latch and the key should rotate freely.c. The key should extend and retract the deadbolt.• For units without a keypad, add card using LCT software and test. • For units with a keypad, add pin and card using LCT software and test. 2. LED signalling:• After using a valid credential, a green ﬂash followed by three fast amber ﬂashes indicates a low power condition. Check the input voltage. If the input voltage is low, disconnect the lock from the power source and check the power source voltage. If the power source voltage is correct, inspect the lock wiring for a possible short.• If the lock loses power, it will ﬂash rapid amber for approximately one minute. After that, the lock will no longer be functional.3. When you have completed the tests, close the door, ensuring latchbolt and deadbolt fully extend into strike plate without binding.PRELIMINARY

SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A8032D -12/10PRELIMINARY

Navigation menu