ASSALOY SCYICLS3 Microprocessor Controlled Networked Lock User Manual 11 0394 Exhibit Cover

ASSA ABLOY Inc. Microprocessor Controlled Networked Lock 11 0394 Exhibit Cover

UserManual.wiki >

SCYICLS3 User Manual

Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: U4A-SCYICLS3 IC: 6982A-SCYICLS3 FCC Rule Part: 15.225, 15.249 IC Radio Standards Specification: RSS-210 ACS Project Number: 11-0394 Manufacturer: Assa Abloy Model: C2-IA/IK Manual

A8122A Pre-Launch Draft11/11Copyright 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Incepta™ Series C2 with Aperio™ TechnologyMortise LockInstallation InstructionsC2

1-800-810-WIRE • www.sargentlock.com • A8122A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.11/11/111234567 Table of ContentsWarning ...................................................................................2General Description .................................................................3Speciﬁcations ..........................................................................3System Overview .....................................................................3Parts Breakdown .....................................................................4Lock Installation ......................................................................6Maintenance .........................................................................14Operational Check ................................................................15Lock LED Indications ............................................................16Changes or modications to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment.Warning 1FCC:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Industry Canada:This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. Any retrot or other eld modication to a re rated opening can potentially impact the re rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specic situation. When retrotting any portion of an existing re rated opening, or specifying and installing a new re-rated opening, please consult with a code specialist or local code ofcial (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.89!

SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A8122A - 11/113 Lock Self Test LED IndicationAfter replacing the battery, a Power On Self Test (POST) is performed. The result is indicated using a series of red and green LED ashes as is described by the gure below:One red, one green ash (1 second each) One red ash followed by 16 red or green ashes (.5 s each)Fig. Lock POST LED indicationThe rst ash is always red. If the POST fails, the color of the 16 trailing ashes indicate the status of each individual test as described by the following table: Blink Meaning if Red Code in Event Log2 Main board firmware corrupt 0x0001 3 Override list corrupt 0x00024 Production data corrupt 0x00045 Security data corrupt 0x00086 Configuration data corrupt 0x00107 Battery power low 0x00208 RFID reader circuit error 0x00409 Voltage regulator error 0x008010 Card detection circuit error 0x010011 Secure area communication error 0x020012 Secure area memory corrupt 0x040013 Secure area sensor or motor error 0x080014 Radio modem communication error 0x100015 Radio modem memory corrupt 0x200016 Radio modem configuration error 0x400017 Radio modem RF circuit error 0x8000NOTE: If the battery is not accepted as new after a power on reset, no POST is performed. Instead, the 10 quick red ashes used to indicate Error in lock is shown.