ASSALOY YRIZW1US Push Button and Touch Screen Deadbolt Locks User Manual 14 0099 Exhibit Cover
ASSA ABLOY Inc. Push Button and Touch Screen Deadbolt Locks 14 0099 Exhibit Cover
ASSALOY >
Contents
- 1. Manual - Model YRD110-ZW-US
- 2. Manual - Model YRD120-ZW-US
Manual - Model YRD110-ZW-US
![5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598Certification ExhibitFCC ID: U4A-YRIZW1USIC: 6982A-YRIZW1USFCC Rule Part: 15.249IC Radio Standards Specification: RSS-210ACS Project Number: 14-0099Manufacturer: Assa Abloy Inc.Models: YRD110-ZW-US, YRD120-ZW-USManual](https://usermanual.wiki/ASSALOY/YRIZW1US.Manual-Model-YRD110-ZW-US/User-Guide-2235274-Page-1.png)
![P/N AYRD-110-INST-FUL Rev Ax4x2x32-3/8" positionUP2-3/4" positionUPPressPullOoptionalx4Installing Latch & Strike Plate1Bolt must be in retracted (unlocked) position. Note horizontal orientation of mechanism.!Installing Keypad Escutcheon2Outside of DoorInside of DoorBolt must be in retracted (unlocked) position. Note horizontal orientation of mechanism.!x2Installing Interior Mounting Plate3Attaching the Cable Assembly4x3Installing Interior Escutcheon5 Testing Operation Handing the LockBolt must be in retracted (unlocked) position before installing batteries.!Installing Cover6Press . Press . Enter new Master PIN code (4-8 digits). Press to complete.Yale Real Living™Installation and Programming Instructions Preparing DoorAfter entering the Master PIN code, press any key to complete handing.Key Free Push Button Deadbolt B1L withWAVE® #8-32 x 5/16’’Machine screws#7 wood & #8-32machine x 20mmCombination screws M6x47mmLong through bolt Congratulations, you've installed the Yale Real Living™ Key Free Push Button Deadbolt B1Lwith ! Turn sheet over for Programming Instructions to customize your product.WAVE®](https://usermanual.wiki/ASSALOY/YRIZW1US.Manual-Model-YRD110-ZW-US/User-Guide-2235274-Page-2.png)
![Programming InstructionsPress Enter Master PIN code Press Enter User number to be created(1-100)*.Enter 4-8 digit PIN code "Unlock"Master PIN Code SettingMM User PIN Code Registration RegisterDeleteAdvanced Lock SettingsAudio ModeN/A All Code Lockout ModeNetwork Setting Join the networkEnableEnableDisableExit the networkDisable User Number (UN)1~100: with network module 1 2UAutomatic Re-lock Enable Disable One Touch Locking Enable Disable Feature Programming Through Menu ModeUsing Master PIN code* *The Master PIN code must be registered prior to any other programming of the lock.Handing the LockFor quiet areas, select Disable (3) in Audio Mode.1. Enter the 4-8 digit Master PIN code followed by the key. 2. Enter digit corresponding to the function to be performed followed by the key. Note: If the lock is connected to a network controller, it is recommended that it is programmed through the centralized user interface (PC or hand-held device) to ensure communication between the lock and the controller unit. Programming Troubleshooting* When batteries are replaced, Network locks have a real time clock that will be set through the User Interface (UI); it is recommended to verify correct date and time particularly those locks operating under Daylight Saving Time (DST).Symptom Suggested ActionLock does not respond – door is open and accessible. • Press each keypad button for response when pressed.• Check batteries are installed and oriented correctly (polarity) in the battery case.• Check batteries are in good condition; replace batteries* if discharged.• Check to see if cable is fully connected and not pinched.• Batteries may be completely discharged.• Apply 9V battery to terminals below the keypad for backuppower option.Unit chimes to indicate code acceptance, but thedoor will not open.• Check to see if there is another locking device on the door.• Check the door gaps for any foreign objects between door and frame.• Check that the cable is firmly connected to the PC board.Unit operates to allow access, but will notautomatically re-lock. • Check to see if Auto Re-lock Mode is enabled.• If low battery indicator is lit (see below), change batteries*.PIN codes will not register.• PIN codes must consist of 4 to 8 digits to register.• The same PIN code cannot be used for multiple users. • Registration/management of PIN codes is set by the authority of the Master Code.• Contact the Master user.• User codes must be entered within 5 seconds or the process will have to be restarted.• Check mark or gear cannot be used as part of theUpon entering a PIN code and pressing the (*) key, thelock gives a series of beeps,flashes red & blue LEDs 7 times, and does not unlock.• All Code Lockout Mode is enabled.• Only the Master can enable/disable All Code Lockout Mode.• Contact the Master user.Upon entering a PIN code and pressing the (*) key, there are different tones.• Check to see if the lock is set to All Code Lockout Mode.• Setting/managing All Code Lockout Mode is done through Master Code only. Contact the Master user. The unit operates, but it makes no sound. • Enable Audio Mode.The unit displays inter-mittent RED flashes. • This is the Low Battery indicator alerting that it is time to replace the batteries. Replace all four (4) batteries* with new AA Alkaline batteries. Upon entering a PIN code and pressing the (*) key, the unit responds with a series of beeps and the keypad flashes three times. • The digits entered were incorrect or incomplete. Re-enter the correct code followed by the check mark (*) key. All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except Master) PIN code access. When attempting to enter a code while the unit is in Lockout, the Status Indicator flashes RED (8 times); the keypad flashes as well.Audio Mode: Choosing Disable (3) in Audio mode shuts off the code confirmation tone play-back for use in quiet areas. Audio mode is enabled or disabled through feature programming by the Master code.Automatic Re-lock Time: After a successful unlock, the unit will automatically re-lock after a default of thirty (30) seconds. Re-lock time is adjustable** from 10-180 seconds.Low Battery: When battery power is low, the Status Indicator flashes RED. If battery power is completely lost, use the 9Volt battery override. To use the 9V battery override apply 9V battery, in either direction, to terminals below the keypad for backup power option. Wake up the lock and enter your pin code to unlock the door. Master PIN Code: The Master PIN code is used for programming and for feature settings. It must be created prior to programming the lock. The Master code will also operate (unlock/lock) the lock.Network Setting: This setting is available thru the main Menu (7) and allows the lock to connect with a network controller. It is also available through the wireless button on the interior escutcheon .One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic Re-lock duration or when Automatic Re-lock is disabled).Shutdown Time: The unit will shutdown for a default of sixty (60) seconds and not allow operation after the wrong code entry limit has been met. When the unit is in Shutdown, the Status Indicator flashes RED; the keypad flashes as well.Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door.User PIN Code: The User code operates the lock. Maximum number of user codes is 100.Wrong Code Entry Limit: After a specified number of unsuccessful attempts at entering a valid PIN code, the unit will shut down and not allow operation. Wrong code entry limit is adjustable from three (3) to ten (10) times**. Default is 5.Lock does not respond – door is locked and inaccessible. PIN code.Press Press Press STOP0:20Press Press Press **Adjustable through a Z-Wave controller.®Definitions Creating Master PIN Code1Press Press Enter 4-8digit MasterPIN Code. Press Creating User PIN Codes2Master PIN code must be created first.*Max User Codes = 100 Unlocking Door with PIN Code3Enter PIN Press Resetting Lock to Factory Default Factory Default SettingsSettings Factory DefaultMaster PIN Code Registration required*Automatic Re-lock DisabledOne Touch Locking EnabledAudio EnabledAutomatic Re-lock Time **30 SecondsWrong Code Entry Limit **5 TimesShutdown Time **60 Seconds**Adjustable through a Z-Wave controller.®*The Master PIN code must be registered prior to any other programming of the lock.When lock is reset to factory defaults all user codes (including the Master PIN code*) are deleted and all programming features are reset to original default settings (see "Factory Default Settings").1. Remove the battery cover.2. Remove the batteries.3. While pressing the reset button (minimum of 3 seconds) reinstall batteries. Release reset button.4. Replace battery cover.Upon reset, Master Code creation is the only option available and must be performed prior to any other programming of the lock. NOTE: After setting the Master Code, press any key to complete handing of the lock.Default settingsin bold.Performsautomatichanding ofthe lock.User ___User ___ User ___ User ___ User ___ User ___ User ___ User ___ User ___ Enrolling Lock In Network ® Low Battery Warning- Flashes REDFailsafe 9 voltBattery ConnectionFCC:®FCC ID: U4A-YRIZW1US (Z-Wave )Model(s): YRD110-ZW-USThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.Industry Canada:®Canadian ID: 6982A-YRIZW1US (Z-Wave )Model(s): YRD110-ZW-USThis Class B digital apparatus meets all requirements of the Canadian Interference CausingEquipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Cet appareillage numérique de la classe B répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée.Section 7.1.2 of RSS-GEN Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.En vertu des règlements d'Industrie Canada, cet émetteur radio ne peut fonctionner avec une antenne d'un type et un maximum (ou moins) approuvés pour gagner de l'émetteur par Industrie Canada. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie.Section 7.1.3 of RSS-GEN This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.Cet appareil est conforme avec Industrie Canada RSS standard exemptes de licence(s). Sonfonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne peut causer des interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.Product Support Tel 800.810.WIRE (9473) • www.yalelocks.comYale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Yale Real Living™ is a trademark of Yale Security Inc., an ASSA ABLOY Group company.Copyright © 2014, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.YALE, with its unique global reach and range of products, is the world's favorite lock– the preferred solution for securing your home, family and personal belongings.ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.!Master PIN Code must be created before any further programming.Max User Codes = 100 Warning: Changes or modifications to this device, not expressly approved by Yale Security Inc. could void the user's authority to operate the equipment.PIN Code Management (With Network Module - Up to 100 Users) Duplicate if necessary User Name User # PIN CodeMasterUser ___User ___ User ___ User ___ Code ChartUser TypeUser ___User ___ User ___ Your network controller first needs to be in enrollment or exclusion mode for the lock to be enrolled or removed from network. Once you put the controller in the enrollment or exclusion mode, the lock can ®be enrolled or removed in the Z-Wave network two ways - through the keypad using the #7 key (see Programming Through Menu Mode) or by pressing the button.To enroll lock using the button option:1. Remove the battery cover.2. Press button and hold until unit beeps two (2) times.3. Release button and network joining automatically begins.4. Replace battery cover.To remove lock using the button option:1. Remove the battery cover.2. Press button and hold until unit beeps five (5) times.3. Release button and network removal automatically begins.4. Replace battery cover.Lock-out Mode- Keypad Flashes](https://usermanual.wiki/ASSALOY/YRIZW1US.Manual-Model-YRD110-ZW-US/User-Guide-2235274-Page-3.png)