ASUSTeK Computer AAM6KVIB6 4-PORT WIRELESS ETHERNET ROUTER User Manual 4 Port Wireless Ethernet Router

ASUSTeK Computer Inc 4-PORT WIRELESS ETHERNET ROUTER 4 Port Wireless Ethernet Router

USERS MANUAL

4-Port Wireless Ethernet RouterAAM6020VI-B6User ManualVersion 1.0Version Date: June 8, 2005
4-Port Wireless Ethernet RouterUser Manual1Version 1.0Table of ContentsGENERAL INFORMATION ............................................................................3Package Contents ...............................................................................3Safety Instructions—Please read. ....................................................3Front Panel View..................................................................................4Back Panel View ..................................................................................5Description .............................................................................................5INSTALLING THE ROUTER ..........................................................................6Connect the ADSL Line and Telephone........................................6Connect the PC to the Router ..........................................................6Connect the Power Adapter..............................................................6INSTALLATION DIAGRAM ............................................................................7CONFIGURING YOUR COMPUTER.............................................................8Windows 2000 ......................................................................................8Windows XP ..........................................................................................9LOGGING INTO THE ROUTER .................................................................. 10DEVICE INFO ............................................................................................. 11Summary ............................................................................................. 11WAN ...................................................................................................... 12STATISTICS ....................................................................................... 12LAN Statistics................................................................................. 12WAN Statistics............................................................................... 13ATM Statistics ................................................................................ 13ADSL Statistics.............................................................................. 14ADSL BER Test............................................................................. 15Route .................................................................................................... 17ARP ....................................................................................................... 18QUICK SETUP ........................................................................................... 19ATM PVC Configuration.................................................................. 19ADVANCED SETUP ................................................................................... 21WAN ...................................................................................................... 21Connection Type........................................................................... 23NAT ....................................................................................................... 27Virtual Servers ............................................................................... 27Port Triggering ............................................................................... 28DMZ Host ........................................................................................ 30Firewall................................................................................................. 30IP Filtering—Outgoing................................................................... 30IP Filtering—Incoming................................................................... 31MAC Filtering ................................................................................. 32
4-Port Wireless Ethernet RouterUser Manual2Version 1.0Port Mapping...................................................................................... 33Quality of Service.............................................................................. 35Routing................................................................................................. 36Default Gateway............................................................................ 36Static Route.................................................................................... 36RIP .................................................................................................... 37DNS....................................................................................................... 38DNS Server..................................................................................... 38Dynamic DNS ................................................................................ 38ADSL..................................................................................................... 39DSL Advanced Settings .............................................................. 40Tone Settings ................................................................................. 40WIRELESS ................................................................................................. 42Basic ..................................................................................................... 42Security ................................................................................................ 42MAC Filter ........................................................................................... 44Wireless Bridge ................................................................................. 45Advanced............................................................................................. 46TROUBLESHOOTING—DIAGNOSTICS ..................................................... 48MANAGEMENT........................................................................................... 48Settings ................................................................................................ 48Backup Settings ............................................................................ 48Restore User Settings ................................................................. 49Restore Default.............................................................................. 50System Log ......................................................................................... 50Configure System Log................................................................. 51SNMP ................................................................................................... 52Internet Times .................................................................................... 52Access Control................................................................................... 53Services ........................................................................................... 53IP Addresses .................................................................................. 53Passwords ...................................................................................... 54Update Software................................................................................ 55Reboot Router.................................................................................... 55APPENDIX .................................................................................................. 56FCC Warning Statement ................................................................. 56Declaration of Conformity for R&TTE directive 1999/5/EC .. 57CE Mark Warning.............................................................................. 57
4-Port Wireless Ethernet RouterUser Manual3Version 1.0General InformationThe 4-Port Wireless Ethernet Router features 4 LAN ports and a wireless ability.Package ContentsIncluded in the package is one of each of the following—•4-Port wireless Ethernet router•15 VAC AC power adapter•RJ-11 telephone cable•RJ-45 Ethernet cable•Splitter•User Manual•Place your router on a flat surface close to the cables in a location with sufficient ventilation.•To prevent overheating, do not obstruct the ventilation openings of this equipment.•Plug this equipment into a surge protector to reduce the risk of damage from power surges and lightning strikes.•Operate this equipment only from an electrical outlet with the correct power source as indicated on the adapter.•Do not open the cover of this equipment. Opening the cover will void any warranties on the equipment.•Unplug equipment first before cleaning. A damp cloth can be used to clean the equipment. Do not use liquid / aerosol cleaners or magnetic / static cleaning devices.Safety Instructions—Please read.
4-Port Wireless Ethernet RouterUser Manual4Version 1.0Front Panel ViewLED Mode IndicationSolid Wireless is enabled.No light Wireless is disabled.APBlinking There is wireless traffic.Solid ADSL is connected.No light ADSL is not connected. The ALARM led will be red.XDSLLinkBlinking The router is connected to ADSL.Solid ADSL is connected, and there is no ADSL traffic.No light ADSL is not connected.XDSLACT QuickblinkingThere is ADSL traffic.Solid Router is connected to the LAN.No light No connection to the LAN. Check if the LAN cable is connected to the router.LAN1-LAN4Blinking LAN trafficSolid (red) ADSL is not connected.ALARM No light ADSL is connected.Solid Router is powered on.POWER No light Router is not powered. Check if the router is plugged in and if the power switch is turned on.
4-Port Wireless Ethernet RouterUser Manual5Version 1.0Back Panel ViewPort DescriptionPower Switchh Press to turn the router on and off.Powerr Connects to a 15 VAC AC power adapter.ResetRestart—press the button for less than 4 seconds.Default settings—press the button for 4 seconds or longer.LAN1-LAN4 RJ-45 connects the unit to an Ethernet device such as a PC or a switch.ConsoleNOTE: To be used by maintenance professionals only. If the router needs repair, bring it to a service professional.Linee RJ-11 cable connects to the splitter provided.
4-Port Wireless Ethernet RouterUser Manual6Version 1.0Installing the RouterConnect the ADSL Line and TelephoneAn RJ-11 cable will be connected to the wall phone jack and theline-end of the splitter. Connect another RJ-11 phone wire from the modem-end of the splitter to the port labeled “ line” on the router. A third RJ-11 phone wire will be needed to connect the telephone to the phone-end of the splitter.NOTE: See connections on the installation diagram.Connect the PC to the RouterUse the Ethernet cable to connect your computer directly to the router. Connect one end of the Ethernet cable to one of the ports labeled LAN on the rear panel of the router and connect the other end to the Ethernet port of your computer. Attach any additional PCs to the router using RJ-45 cables to the port labeled LAN on the rear panel of the router.Connect the Power AdapterComplete the process by connecting the AC power adapter to the POWER connector on the back of the device and plug the adapter into a wall outlet or power strip. Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them.
4-Port Wireless Ethernet RouterUser Manual7Version 1.0Installation Diagram
4-Port Wireless Ethernet RouterUser Manual8Version 1.0Configuring Your ComputerPrior to accessing the router through the LAN port, note the following necessary configurations —•Your PC’s TCP/IP address: 192.168.1.___( the last number is any number between 3 and 254)•The router’s default IP address: 192.168.1.1•Subnet mask: 255.255.255.0Below are the procedures for configuring your computer. Follow the instructions for the operating system that you are using.Windows 20001. In the Windows taskbar, click on the Start button and point to Settings, Control Panel, and Network and Dial-upConnections (in that order).2. Click on Local Area Connection. When you have the Local Area Connection Status window open, click on Propertiess.3. Listed in the window are the installed network components.If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled, and you can skip to Step 10.4. If Internet Protocol (TCP/IP) does not appear as an installed component, then click on Installl.5. In the Select Network Component Type window, click on protocol and then the Addd button.6. Select Internet Protocol (TCP/IP) from the list and then click on OKK.7. If prompted to restart your computer with the new settings, click OKK.8. After your computer restarts, click on the Network and Dial-up Connections icon again, and right click on the Local Area Connection icon and then select Properties.
4-Port Wireless Ethernet RouterUser Manual9Version 1.09. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP) and then click on Propertiess.10. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button labeled Use the following IP addresss and type 192.168.1.x (where x is any number between 2 and 254) and 255.255.255.0 in the IP address field and Subnet Mask field.11. Click on OKK twice to save your changes and then close the Control Panell.Windows XP1. In the Windows taskbar, click on the Start button and pointto Settings and then click Network Connections.2. In the Network Connections window, right click on the Local Area Connection icon and click on properties.3. Listed in the Local Area Connection window are the installed network components. Make sure the box for Internet Protocol (TCP/IP) is checked and then click on Propertiess.4. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button labeled Use the following IP addresss and type 192.168.1.x (where x is any number between 2 and 254) and 255.255.255.0 in the IP address field and Subnet Mask field.5. Click on OKK twice to save your changes and then close the Control Panell.
4-Port Wireless Ethernet RouterUser Manual10Version 1.0Logging into the RouterThis section explains how to log in to your router using the following steps—1.. Launch your web browser.2.. Enter the URL http://192.168.1.1 in the address bar and click on Enterr.A login screen like the one below will be displayed after you connect to the user interface.3. Enter your user name and password, and then click on OKto display the user interface. NOTE: There are two default user name and password combinations. The user / user name and password combination can display device status, but cannot change or save configurations. The admin / admin combination can perform all functions. Passwords can be changed at any time.
4-Port Wireless Ethernet RouterUser Manual11Version 1.0Device InfoThis section describes the system information that can be accessed using the menu items under Device Info.SummaryAccess the general status report from the router by clicking on “Summaryy” under “Device Infoo” . It shows information about the router such as the version of the software, bootloader, etc. It also displays the current status of your DSL connection as shown below—
4-Port Wireless Ethernet RouterUser Manual12Version 1.0WANAccess the WAN status report from the router by clicking on “WANN” under “Device Info”.STATISTICSLAN StatisticsAccess the LAN statistics from the router by clicking on the “ LAN” item under “ Statistics” .
4-Port Wireless Ethernet RouterUser Manual13Version 1.0WAN StatisticsAccess the WAN statistics from the router by clicking on the “WANN” item under “Statisticss” .ATM StatisticsAccess ATM statistics from the router by clicking on the “ATMM”item under “Statisticss”.
4-Port Wireless Ethernet RouterUser Manual14Version 1.0ADSL Statistics You can view ADSL statistics by clicking on the “ADSLL” item under “Statisticss” . Information contained in this screen is useful for troubleshooting and diagnostics of connection problems.
4-Port Wireless Ethernet RouterUser Manual15Version 1.0ADSL BER TestABit Error Rate Test (BER Test) is a test that reflects the ratio of error bits to the total number transmitted. If you click on the ADSL BER Test button at the bottom of the ADSL Statistics page, the following pop-up screen will appear allowing you to set the tested time and to begin the test.Below is an ADSL BER Test result screen displaying informationabout the test and the error bits and ratio.
4-Port Wireless Ethernet RouterUser Manual16Version 1.0
4-Port Wireless Ethernet RouterUser Manual17Version 1.0RouteAccess the routing status report from the router by clicking on the “Routee” item under “Device Infoo”.
4-Port Wireless Ethernet RouterUser Manual18Version 1.0ARPAccess the ARP status report from the router by clicking on the “ARPP” item under “ Device Infoo” .
4-Port Wireless Ethernet RouterUser Manual19Version 1.0Quick SetupThis section will explain how to configure the router.ATM PVC ConfigurationTo enable the auto-connect process, click on the box labeled DSL Auto-connect, a process that will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To continue, click on the Nextt button.If you do not use DSL Auto-connect, then you may need to change the VPI and VCI numbers. Quality of service can also be enabled on this screen.Furthermore, if you do not use DSL Auto-connect, then you will need to select the connection type and encapsulation mode from a list as shown below.
4-Port Wireless Ethernet RouterUser Manual20Version 1.0The next screen to appear will depend on the connection type that was selected in the previous screen. The following screen is a result of choosing IP over ATM (IPoA) as the connection type.
4-Port Wireless Ethernet RouterUser Manual21Version 1.0Advanced SetupThis section contains information about WAN, LAN, and ADSL settings.WANConfigure the WAN settings as provided by your ISP.Click on the Addd button if you want to add a new rule for the WAN interface. The ATM PVC Configuration screen appears. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category.
4-Port Wireless Ethernet RouterUser Manual22Version 1.0Verify the following values with your ISP before you change them.•VPI:: Virtual Path Identifier. The valid range is 0 to 255.•VCI:: Virtual Channel Identifier. The valid range is 32 to 65535.•Service Category:: Five classes of traffic are listed—oUBR Without PCRoUBR With PCRoCBRoNon Realtime VBRoRealtime VBREnabling QoS for a PVC improves performance for selected classes of applications. However, since QoS also consumes system resources, the number of PVCs is reduced. If you want to enable QoS service, click on the Enable Quality Of Servicee check box.
4-Port Wireless Ethernet RouterUser Manual23Version 1.0Connection Type This screen shows the below types of network protocols and encapsulation modes—•PPP over ATM (PPPoA)•PPP over Ethernet (PPPoE)•MAC Encapsulation Routing (MER)•IP over ATM (IpoA)•BridgingSelect the mode that your ISP has instructed you to use and click on Nextt.After you click on Nextt, the below screen appears allowing you disable the bridge service if desired.
4-Port Wireless Ethernet RouterUser Manual24Version 1.0When the settings are complete, the next screen shows a WANSetup – Summary screen displaying the WAN configurations made.Click on the Savee button when the settings are correct. The below screen will appear showing the WAN settings that you made. When satisfied with the settings, and no changes are necessary, click on the Finishh button. To remove any settings, click on the Removee button.
4-Port Wireless Ethernet RouterUser Manual25Version 1.0After selecting the Finishh button, the below screen will appear. At this point, the router will reboot to save the changes made.
4-Port Wireless Ethernet RouterUser Manual26Version 1.0LAN Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond your LAN’s IP Subnet. The Savee button only saves the LAN configuration data, but does not apply the configurations. Select the Save/Reboott button to save the LAN configuration data and reboot the router and apply the new configurations.
4-Port Wireless Ethernet RouterUser Manual27Version 1.0NATIf you enable NAT (Network Address Translation), you can configure the Virtual Server, Port Triggering, and DMZ Host.Virtual ServersA virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side. Select the virtual server from the drop-down list and complete the server IP address, then click on the Save / Apply button.
4-Port Wireless Ethernet RouterUser Manual28Version 1.0The following screen appears after you save your selection. To add additional virtual servers, click on the Addd button. If you need to remove any of the server names, select the check box and clickon the Removee button.Port Triggering Click on the Addd button to add Port Triggering to your Internet application.The below screen appears when you click on Addd allowing you to select the application that you want to set the port settings for.After a selection has been made, click on the Save / Apply button.
4-Port Wireless Ethernet RouterUser Manual29Version 1.0The below screen appears after you save your selections. You will be able to add or remove selections made, by clicking on the Addd and Removee buttons.
4-Port Wireless Ethernet RouterUser Manual30Version 1.0DMZ Host You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save / Applyy.FirewallIP Filtering—OutgoingThe outgoing filter will block the LAN traffic from entering the WAN side. Click on the Addd button to create filters. The below screen will appear when you click on Addd. Input the filter name, source information (from the LAN side), and destination information (from the WAN side). Then click on Save / Applyy.
4-Port Wireless Ethernet RouterUser Manual31Version 1.0IP Filtering—IncomingIncoming filter filters the WAN traffic to the LAN side. Click on the Addd button to add incoming filter settings. Enter a filter name, information about the source address (from the WAN side), and information about the destination address (to the LAN side). Select the protocol and WAN interface, then click on Save/Applyy to add the setting.You can view and delete the incoming filter settings from this screen.
4-Port Wireless Ethernet RouterUser Manual32Version 1.0MAC Filtering MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. If you click on Change Policyy, a confirmation dialog allows you to verify your change.
4-Port Wireless Ethernet RouterUser Manual33Version 1.0If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save / Apply tosave it. After you save the settings, a screen showing the settings will appear. On this screen you will be able to view and delete MAC filtering rules. Port MappingPort mapping is a feature that allows you to open ports to allow certain Internet applications on the WAN side to pass through the firewall and enter your LAN. To use this feature, mapping groups need to be created. To do this, follow the below instructions—1. Click on the Addd button as displayed below.
4-Port Wireless Ethernet RouterUser Manual34Version 1.02. After clicking the Addd button, the below configuration screen appears, allowing you enter the groups and the interfaces they are associated with.
4-Port Wireless Ethernet RouterUser Manual35Version 1.0 Quality of Service You can configure the Quality of Service to apply different priorities to traffic on the router. On this screen you can view and delete QoS settings.
4-Port Wireless Ethernet RouterUser Manual36Version 1.0RoutingDefault Gateway You can enable automatic assigned default gateway on the Routing – Default Gateway screen. As default, the box is checked for automatic assigned default gateway to be enabled. Click the Save / Apply button to enable or disable this feature. Static Route Use the Routing – Static Route screen to add a static route to the routing table. Enter the route information and click on Save/Applyy to make it active. No reboot is required.
4-Port Wireless Ethernet RouterUser Manual37Version 1.0RIPIf RIP is enabled, the router operation can be configured as active or passive.
4-Port Wireless Ethernet RouterUser Manual38Version 1.0DNSDNS Server Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and secondary DNS.Dynamic DNS
4-Port Wireless Ethernet RouterUser Manual39Version 1.0ADSLThere are three major items in the ADSL settings: Modulation Methods Six modulation methods for different linking speed are supported by the 6211 ADSL router: G.Dmt Enabled, G.lite Enabled, T1.413 Enabled, ADSL Enabled, Annex L Enabled, and ADSL2+ Enabled. Set this value only as directed by your ISP. Phone Line Pair The 6211 ADSL router supports phone lines on pins 2 and 3 or pins 1 and 4 to connect your ADSL line. If your phone systemuses pins 2 and 3, attach a normal RJ11 cable to the router and select “ Inner pair” on the screen; if your phone system uses pins 1 and 4, attach the phone with the supplied RJ11 cable and select “ Outer pair” on the screen. CapabilityDo not change these settings unless directed by your ISP.
4-Port Wireless Ethernet RouterUser Manual40Version 1.0DSL Advanced SettingsThe test mode can be selected from the DSL Advanced Settings page.Test modes are as follows—•Normal•Reverb•Medley•No retrain•L3Tone SettingsThe frequency band of ADSL is split up into 256 separate tones, each spaced 4.3125 kHz apart. With each tone carrying separate data, the technique operates as if 256 separate modems were running in parallel. The tone range is from 0 to 31 for upstreamand from 32 to 255 for downstream. Do not change these settings unless so directed by your ISP.
4-Port Wireless Ethernet RouterUser Manual41Version 1.0
4-Port Wireless Ethernet RouterUser Manual42Version 1.0WirelessThis section allows you to configure wireless settings on your router.BasicThe below Wireless – Basic screen lets you enable or disable wireless. The default setting for wireless is enabled. You can also hide the access point so others cannot see your ID on the network.SecurityThe next screen is the Wireless – Securityy screen which allows you to select the network authentication method and to enable or disable WEP encryption. Note that depending on the network authentication that is selected, the screen will change accordingly so additional fields can be configured for the specific authentication method.Network authentication methods include the following—•Openn—anyone can access the network. The default is a disabled WEP encryption setting.•Sharedd—WEP encryption is enabled and encryption key strength of 64-bit or 128-bit needs to be selected. Click on Set Encryption Keys to manually set the network encryption keys. Up to 4 different keys can be set and you can come back to select which one to use at anytime.
4-Port Wireless Ethernet RouterUser Manual43Version 1.0•802.1X——requires mutual authentication between a clientstation and the router by including a RADIUS-basedauthentication server. Information about the RADIUS server such as its IP address, port and key must be entered.WEP encryption is also enabled and the encryption strength must also be selected.•WPA—(Wi-Fi Protected Access))— usually used for the larger Enterprise environment, it uses a RADIUS server and TKIP (Temporal Key Integrity Protocol) encryption (instead of WEP encryption which is disabled). TKIP uses128-bitdynamic session keys (per user, per session, and per packet keys).•WPA-PSK (Wi-Fi Protected Access – Pre-Shared Key))—WPA for home and SOHO environments also using the same strong TKIP encryption, per-packet key construction, and key management that WPA provides in the enterprise environment. The main difference is that the password is entered manually. A group re-key interval time is also required.•WPA2 (Wi-Fi Protected Access 2)) —second generation of WPA which uses AES (Advanced Encryption Standard) instead of TKIP as its encryption method. Network re-authinterval is the time in which another key needs to be dynamically issued.•WPA2-PSK (Wi-Fi Protected Access 2 – Pre-Shared Key))—suitable for home and SOHO environments, it also uses AES encryption and requires you to enter a password andan re-key interval time.•Mixed WPA2 / WPAA—during transitional times for upgrades in the enterprise environment, this mixed authentication method allows “ upgraded” and users not yet “ upgraded” to access the network via the router. RADIUS server information must be entered for WPA and a as well as a group re-key interval time. Both TKIP and AES are used.•Mixed WPA2 / WPA-PSKK—useful during transitional times for upgrades in the home or SOHO environment, a pre-shared key must be entered along with the group re-keyinterval time. Both TKIP and AES are also used.
4-Port Wireless Ethernet RouterUser Manual44Version 1.0MAC FilterThe MAC filter screen allows you to manage MAC address filters.Add the MAC addresses that you want to manage and then select the mode that you want to use to manage them. You can disable this feature or you can allow or deny access to the MAC addresses that you add to the list.The following screen appears when you want to add a MAC address to the filter. When completed, click on the Save / Apply button.
4-Port Wireless Ethernet RouterUser Manual45Version 1.0Wireless BridgeIn this next screen, you can select which mode you want the router to be in, either access point or wireless bridge.
4-Port Wireless Ethernet RouterUser Manual46Version 1.0AdvancedAdvanced features of the wireless LAN interface can be configured in this section.Settings can be configured for the following—•AP Isolationn—if you select enable, then each of your wireless clients will not be able to communicate with each other.•Bandd—a default setting at 2.4GHz – 802.11g•Channell-- 802.11b and 802.11g use channels to limit interference from other devices. If you are experiencing interference with another 2.4Ghz device such as a baby monitor, security alarm, or cordless phone, then change the channel on your router.•Multicast Ratee—the rate at which a message is sent to a specified group of recipients.•Basic Ratee—the set of data transfer rates that all the stations will be capable of using to receive frames from a wireless medium.•Fragmentation Thresholdd—used to fragment packets which help improve performance in the presence of radio frequency (RF) interference.•RTS Threshold (Request to Send Threshold)) —determinesthe packet size of a transmission through the use of the router to help control traffic flow. •DTIM Intervall—sets the Wake-up interval for clients in power-saving mode.•Beacon Intervall—a packet of information that is sent from a connected device to all other devices where it announces its availability and readiness. A beacon interval is a period of time (sent with the beacon) before sending the beacon again. The beacon interval may be adjusted in milliseconds (ms).
4-Port Wireless Ethernet RouterUser Manual47Version 1.0•Xpress Technology——a technology that utilizes standards based on framebursting to achieve higher throughput. With Xpress Technology enabled, aggregate throughput (the sum of the individual throughput speeds of each client on the network) can improve by up to 25% in 802.11g only networks and up to 75% in mixed networks comprised of 802.11g and 802.11b equipment.•54g Mode—— 54g is a Broadcom Wi-Fi technology.•54g Protectionn--the 802.11g standards provide a protection method so 802.11g and 802.11b devices can co-exist in the same network without “ speaking” at the same time. Do not disable 54g Protection if there is a possibility that a 802.11b device may need to use your wireless network. In Auto Mode, the wireless device will use RTS/CTS (Request to Send / Clear to Send) to improve 802.11g performance in mixed 802.11g/802.11b networks. Turn protection off to maximize 802.11g throughput under most conditions.•WMM (Wi-Fi Multimedia)) —feature that improves the your experience for audio, video and voice applications over a Wi-Fi network.
4-Port Wireless Ethernet RouterUser Manual48Version 1.0Troubleshooting—DiagnosticsThe diagnostics screen allows you to run diagnostic tests to check your DSL connection. In addition, you can test the connection to your DSL service provider.ManagementSettingsBackup Settings
4-Port Wireless Ethernet RouterUser Manual49Version 1.0Restore User Settings To restore saved settings, select Management Settings Restore User Settings .ШШSelect the backup file you want to restore and click on UpdateSettingss.The router will restore settings and reboot to activate the restored settings.
4-Port Wireless Ethernet RouterUser Manual50Version 1.0Restore Default Restore Default will erase all current settings and restore the router to factory default settings. To restore the router to factory default settings, select Management Settings Restore Default.ШШReply OK to the confirmation dialog. The router will restore the default settings and reboot.System Log The System Log dialog allows you to view the System Log and configure the System Log options. To view the System Log click on the View System Logg button to check the log file.
4-Port Wireless Ethernet RouterUser Manual51Version 1.0Below is a view of the System Logg.Configure System Log If the log is enabled, the system will log selected events: Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. All events above or equal to the selected log level will be logged and displayed.If the selected mode is “ Remote” or “ Both” , events will be sent to the specified IP address and UDP port of a remote system log server. If the selected mode is “ Local” or “ Both” , events will be recorded in the local memory. Select the desired values and click on the “Save/Applyy” button to configure the system log options.
4-Port Wireless Ethernet RouterUser Manual52Version 1.0SNMPInternet Times
4-Port Wireless Ethernet RouterUser Manual53Version 1.0Access ControlYou can enable or disable some services of your router by LAN or WAN. If no WAN connection is defined, only the LAN side can be configured.ServicesIP AddressesWeb access to the router can be limited when Access ControlMode is enabled. The IP addresses of allowed hosts can be added using Access Control IP Address.ШAdd the IP address to the IP address list by clicking on the Addbutton, then select “Enabledd” to enable Access Control Mode.
4-Port Wireless Ethernet RouterUser Manual54Version 1.0To assign the IP address of the management station that is permitted to access the local management services, enter the IP address in the box and click on the Save / Apply button.PasswordsAccess the Passwordss screen under the Access Controll sectionto change a password. Select an account and enter the current password and the new password and then click on the Save / Applyy button.
4-Port Wireless Ethernet RouterUser Manual55Version 1.0Update Software If your ISP releases new software for this router, follow these steps to perform an upgrade. 1. Obtain an updated software image file from your ISP. 2. Enter the path to the image file location or click on the Browse button to locate the image file. 3. Click the Update Softwaree button once to upload the newimage file.Reboot RouterSelect Management Reboot Router to reboot the router usingШthe web interface. The router will save the current configuration and reboot itself using the new configuration.
4-Port Wireless Ethernet RouterUser Manual56Version 1.0AppendixFCC Warning StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:ЁReorient or relocate the receiving antenna.ЁIncrease the separation between the equipment and receiver.ЁConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.ЁConsult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority tooperate the equipment.This device and its antenna(s) must not be co-located oroperating in conjunction with any other antenna or transmitterTo maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with minimumdistance 20cm between the radiator and your body. Use on the supplied antenna.
4-Port Wireless Ethernet RouterUser Manual57Version 1.0Declaration of Conformity for R&TTE directive 1999/5/ECEssential requirements – Article 3Protection requirements for health and safety – Article 3.1aTesting for electric safety according to EN 60950-1 has beenconducted. These are considered relevant and sufficient.Protection requirements for electromagnetic compatibility – Article 3.1bTesting for electromagnetic compatibility according to EN 301489-1 and EN 301 489-17 has been conducted. These areconsidered relevant and sufficient.Effective use of the radio spectrum – Article 3.2Testing for radio test suites according to EN 300 328 has been conducted. These are considered relevant and sufficient.CE Mark WarningThis is a Class B product, in a domestic environment, this productmay cause radio interference, in which case the user may be required to take adequate measures.

Navigation menu