ATBS Technology SC-BT6000C TPMS for iPod, iPhone, iPad User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3155392
Application ID	2BP6zT+fLJIxJuY94bzWWg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.16kB (577046 bits)
Date Submitted	2016-10-04 00:00:00
Date Available	2016-11-04 00:00:00
Creation Date	2015-12-16 10:23:35
Producing Software	Microsoft® Word 2013
Document Lastmod	2015-12-16 10:23:35
Document Title	Users Manual
Document Creator	Microsoft® Word 2013
Document Author:	Patrick Peng

iTPMSystem for iPod, iPhone, iPad User’s Guide
3. System Installation
1. Introduction
3.1 Install Receiver ：
3.1.1 Plug in OBDII connector.
3.1.2 Plug in mini USB into the receiver.
This Tire Pressure Monitoring System (TPMS) was
designed for increasing security, reliability, and
understanding on tire conditions of your car. Once you
properly install the TPMS, these sensors will
automatically monitor pressures and temperatures of tires
in real time, and send these data to Receiver through
Bluetooth communications. When there is any abnormal
pressure (under or over inflated) and/or temperature of
3.2 Install A-Type Sensor:
tire detected, iPhone, iPod, and iPad will alert driver
3.2.1 The sensor label already indicates the sensor ID
immediately. This system could ensure you are driving in
and its wheel order.
safety.
Example:
About This Manual
 The information in this manual is subject to change
without notice.
 This manual has been created with extra care. In
case that you have any comments or questions
regarding this manual, please contact your local
dealer or our Customer Service Center.
 Before operating this set, please fully understand
the prerequisite such as specifications or
constraints of the hardware and software. We are
not responsible and have no liability for any loss,
damage or injury as a result of misuse.
Sensor Model: AT67
Photograph
A-type
M-type
Cable
(OBDII to
Mini USB)
Cap parts
Lock Nut
Tool
User Guide
Velcro
Copyright (C) ATBS Technology Co. R4.5e
ID:3C0886B5
3.2.1 Place batteries into the
sensor and screw the top cap of. Please attend to the
electrode of the battery.
3.2.2 Remove original valve cap and screw lock nut (1)
and become (2). Screw the Sensor onto valve stem
2. Check Accessories
Part
Receiver
Wheel Order: 01:L1
BT6000C-A
BT6000C-M
to
clockwise (3). Screw (1) lock nut back and use wrench
to lock tightly (4). (3)(4) steps could effectively prevents
sensor from removing.
Note：
(1) Beware of the conductivity between the sensor
and valve stem.
(2) Sensors are supposed to be well locked valve
stem to avoid from leaking.
(3) Please replace sensor battery in case voltage is
below 2.6v.
3.3 Install M-Type Sensor :
3.3.1 Check sensor ID & configures tire.
There are initial sensor configured locations marked.
3.3.2
Tire location
01: Left Front (L1/LF)
02: Right Front(R1/RF)
04: Left Rear (L2/LR)
03: Right Rear(R2/RR)
iTPMS App is for free. Trough the iTPMS you can know
temperature and pressure, battery voltage of the tires of
each sensor’s ID.
4.1 Install App
Note : Each sensor has its ID set by manufacturer.
4.1-1 Download the APP: TPMS
from Apple Store.
4.1-2 Go to Setting  General  Bluetooth Page.
4.1-3 Turn on the Bluetooth, and it will scan the devices
automatically.
4.1-4 Find iTPMS device and pair it.The name of device is
iTPMS XXXXXX (X=0-9)
3.3.3
3.3.3 Install Internal Sensor (M-type)
4.1-5 As pairing works, you could sign up sensor’s ID on
iPod, iPhone and iPad.
i.
ii.
iii.
iv.
v.
Remove the tires from vehicles.
Deflate the tires and detach rim and tire.
Install sensor on rim to appropriate position.
Balance wheels.
Install wheel to appropriate position of
vehicle.
4.1-6 Install the battery, and set the sensor’s ID. When the
setting works, you would see the tire pressure.
4.
iTPMS APP Installation:
Copyright (C) ATBS Technology Co. R4.5e
4.2 Operate APP
Note : Each sensor has its ID set by manufacturer.
4.2-1 Tap More following with Learning Sensor ID and
sign up sensor’s ID.
5. Specification
5.1 BT6000C receiver:
Operation Voltage
9~24V
Operation Current
50 mA
Operation
-10~ 70 ℃
Temperature
TPMS Frequency
433.92 MHz
BT Frequency
3.0SPP
5.2 Sensor:
4.2-2 Place the battery correctly.When the sensor detects
Operation
Temperature
Operating
Humidity
Frequency
Monitoring
Pressure
Battery
Weight
the change of pressure,ID will turn red to alert users.
-40 °C to 125 ± 1°C
100%
433.92MHz
0~132 psi
2.9 V ± 0.1V
A-type
M-type
A-type
Battery Lifespan
M-type
9.0g ± 0.2g
27g ± 0.5g
About 8~12
months
5 years
6. Caution：
6.1 Information provided in user’s guide is for reference
only. You could operate the device only when your
vehicle stops.
6.2 This equipment may lead to malfunction due to some
harmful interference systems.
6.3 Four sensors’ IDs of this product have already set by
4.2-3 On Setup page, you can set up the pressure and the
the manufacturer. If you would like to replace new
temperature of the unit.
sensors, please seek the agent for assistance.
6.4 Do not soak our product or sensor in the water or
chemical. Chemicals are not allowed to clean.
6.5 Do not replace the rubber gasket arbitrarily. If there is
any failure, please replace it with certified product.
6.6 The warranty of the product lasts for one year, please
use the product correctly. The warranty excludes natural
and artificial disasters, drops, soaking in water accident,
fire accident, anomalistic power supply and other
damage.
6.7 The warranty won’t cover any consumptive
accessories like: the packaging, Velcro, manual, etc.
6.8 Please refer to the steps from user’s guide to avoid
any abnormal operation. It may lead to malfunction.
6.9 Any changes or modifications in construction of this
device which are not expressly approved by the party
Copyright (C) ATBS Technology Co. R4.5e
responsible for compliance could void the user’s authority
to operate the equipment.
6.10 Please follow the instruction of power supply. Wrong
process of power supply would cause malfunction. Please
use the certified battery. Improper battery or wrong
procedures will affect efficiency or cause malfunction of
sensors.
6.11 Please observe the pressure, temperature and
voltage of battery. If the sensor hasn’t worked for a long
time, please check your sensor.
6.12 FCC Notice
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions (1) the
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation. This
equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Notice: Any modifications or any system
alterations cannot guarantee the user’s rights is
protected continuously.
Copyright (C) ATBS Technology Co. R4.5e

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : zh-TW
Tagged PDF                      : Yes
Author                          : Patrick Peng
Creator                         : Microsoft® Word 2013
Create Date                     : 2015:12:16 10:23:35+08:00
Modify Date                     : 2015:12:16 10:23:35+08:00
Producer                        : Microsoft® Word 2013

EXIF Metadata provided by EXIF.tools