ATID RM100USA UHF RFID READER User Manual Microsoft PowerPoint RM 100USA User s manual

ATID Co., Ltd UHF RFID READER Microsoft PowerPoint RM 100USA User s manual

USERS MANUAL

RM-100 USA User’s ManualKey Features•ISO 18000-6C(Gen2) protocol support•Dynamic RF output power : -4dBm to +27dBm•Low current to extend battery life•Compact size•Low costUHF RFID READER MODULE
Introduction and system composition diagram2•The RM-100EUROPE is an compact size RFID reader module developed for the embedded reader market, which comprises printers, industrial PDA , and similar devices.•Target Application- PDA type RFID Reader-RFID PRINTER - OEM Module- Other application◈Introduction ◈◈System composition diagram ◈UARTTag #1Tag #2Tag #N
Composition partsReader module AntennaUser manual3Interface connector cable
Module Description4ANT port : connect rf cable toreader module and ANT.VCC : 4.0 V 1A USB_D-TXDRXDVCCGNDUSB_D+RF switch connector : TX, RX test port.
5◈Nesslab RFID Mobile Reader Application v1.0 setting- Program Setting1. Connect serial data cable (RS-232 to UART) to PC and Reader.2. Run “Nesslab RFID Mobile Reader Application v1.0 ”with window XP 3. First, check “Serial , ISO 1800-6C and COM1 “.4. Supply 4.0v to module. The buzzer is sounded “BEEP “Operation method ----------(1)
Operation method ----------(2)64. Click “connect “.
Operation method ----------(3)65. Cleck “확인 “6. If this screen is displaied“, the program setting is complited
Operation method ----------(4)6-Program Setting1. The channel setting operation1) If the frequency hopping ON/OFF check box is checked, set the frequency hopping ON/OFF check box unchecked.2) Write the channel number to the CH NUM box.3) Click “SET “, then the channel setting is completed4) If you click “Multi Read “the module read the tags at the channel which you check.5) The tag data is displayed at the Result box.
Operation method ----------(4)62. The normal operation1) If the frequency hopping ON/OFF check box is unchecked, set the frequency hopping ON/OFF check box checked.2) If you click “Multi Read “, the module read the tags.3) The tag data is displayed at the Result box.
Channel Table6918.0 MHz40914.0 MHz20917.8 MHz39913.8MHz19917.6MHz38913.6MHz18917.4 MHz37913.4 MHz17917.2 MHz36913.2 MHz16917.0 MHz35913.0 MHz15916.8 MHz34912.8 MHz14916.6 MHz33912.6 MHz13916.4 MHz32912.4 MHz12916.2 MHz31912.2 MHz11920.0 MHz50916.0 MHz30912.0MHz10919.8 MHz49915.8 MHz29911.8 MHz9919.6 MHz48915.6 MHz28911.6 MHz8919.4 MHz47915.4 MHz27911.4 MHz7919.2 MHz46915.2 MHz26911.2 MHz6919.0 MHz45915.0 MHz25911.0 MHz5918.8 MHz44914.8 MHz24910.8 MHz4918.6 MHz43914.6 MHz23910.6 MHz3918.4 MHz42914.4 MHz22910.4 MHz2918.2 MHz41914.2 MHz21910.2 MHz1FREQUENCYCHANNEL NOFREQUENCYCHANNEL NOFREQUENCYCHANNEL NO
- Additional Page - Cautions Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received. Including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio Frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. FCC RF EXPOSURE: The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the user.

Navigation menu