ATOP Technologies SE5901B-AF Industrial Cellular Serial Device Server, Industrial Cellular Modbus Gateway, Industrial Cellular Modbus Concentrator, Industrial Cellular Protocol Gateway User Manual SE MB PG 5901B 2018 12 10

ATOP Technologies, INC. Industrial Cellular Serial Device Server, Industrial Cellular Modbus Gateway, Industrial Cellular Modbus Concentrator, Industrial Cellular Protocol Gateway SE MB PG 5901B 2018 12 10

User Manual

Industrial Cellular Serial Device ServerIndustrial Cellular Modbus GatewayIndustrial Cellular Modbus ConcentratorIndustrial Cellular Protocol GatewaySE5901B/MB5901B/PG5901B Series89900500GUpdated in December, 2018Version V1.2Inside the package you will find the following items: Industrial 3G/4G Serial Gateway x 1 or Industrial 3G/4G Modbus Gateway x 1 or Industrial 3G/4G Modbus Concentrator x 1 or Industrial 3G/4G Protocol Gateway x 1 3-Pin 5.08mm Lockable Terminal Block (Already mounted to the device) x 1 2x7 Pin 3.5mm Lockable Terminal Block (IO version only) x 1 DIN-Rail Kit (Already mounted to the device) x 1 Installation Guide with Warranty Card x 1This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that maycause undesired operation.Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not nstalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help.The antenna(s) used for this transmitter must not be co-located of operating in conjunction with any other antenna or transmitter. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Ln order to avoid the possibility of exceeding the Fcc radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8inches) during normal operation.Never install or work on electrical or cabling during periods of lightning activity. Never connect or disconnect power when hazardous gases are present.Warning:Hot Surface Do Not Touch. IndoorIndoorThis equipment should be installed indoor and not connect directly with equipment installed outdoor.TOP View Bottom View71234561. Grounding Screw2. SMA Connector for Antenna (4G version only)3. Frame Ground4. Terminal for Power 5. USB26. PWR Reset7. SMA Connector for Antenna (4G version only)Front View3G DB9 Type1~45111213144G DB9 Type 1~451112134G IO Type1~467~101112133G IO Type1~467~10111213141. PWR LED2. RUN LED3. COM1 Tx LED4. COM1 Rx LED5. 9-Pin Male D-Sub Connector for RS-232/4856. 14-Pin 3.5 mm Terminal Block for RS-232/485(COM1), RS-232(COM2), Relay, and DI7. Relay2 LED8. Relay1 LED9. DI2 LED10. DI1 LED11. Default Button12. PWR USB13. 10/100/1000 BASE-T(X) Ports14. SMA Connector for Antenna (D3G version only)The device'sground the device properly1245.3. Proceed then to fix the antennas to the female RP-SMA connectors deemed to (Fig. 3). You can then choose whether to plug in the I/O ports at this point or do it later depending on the actual location of the device or level of comfort for performing such operation. 345215
Pin Assignments and Connections10/100/1000BASE-T(X) Ethernet Pinout10/100Base-T(X)1000Base-T(X)9-Pin Male D-Sub Connector for RS-232/4852 x 7-pin Male Terminal Block for RS-232/485(COM 1),RS-232(COM 2) Relay and DI––––––Relay Output with current carrying capacity of 1A@30 VDC (Normal open)Rx1CTS8910 Tx1/D+111213141234567RTS/D-SGRx2Tx2AssignmentDI1DI2RY1cRY1+RY2cRY2+SGAssignment1 2 3 4 5 6 78 9 10 11 12 13 14COM-TXCOM-RXBlinkingOffBlinkingOffGreenGreenCOM port is transmitting dataCOM port is not transmitting dataCOM port is receiving dataCOM port is not receiving dataOrange(Speed)LANPower GreenOnOnOffOffOffBlinkingslowly Ethernet is transmitting at 100MbpsBlinkingOn/OffBlinkingEthernet is transmitting at 1GbpsPower is being suppliedEthernet is transmitting at 10MbpsEthernet no data transmitPower is not suppliedEthernet data is transmittingSystem is not ready or haltAP Firmware is running normallyGreenGreen(Data)RUNRear ViewSide ViewBottom ViewTop ViewSE/MB/PG5901B-D3GSE/MB/PG5901B-4GSE/MB/PG5901B-IO-D3GSE/MB/PG5901B-IO-4GFront View3218,5122,631,5121,548,39012,5107134,6Customers shall always obtain an authorized "RMA" number from Atop before shipping the goods to be repaired to Atop. When in normal use, a sold product shall be replaced with a new one within 3 months after purchase. The shipping cost from the customer to Atop will be reimbursed by Atop.After 3 months and still within the warranty period, it is up to Atop whether to replace the unit with a new one; normally, as long as a product is under warranty, all parts and labor are free of charge to the customers.After the warranty period, the customer shall cover the cost for parts and labor.Three months after purchase, the shipping cost from the customer to Atop will not be reimbursed, but the shipping cost from Atop to the customer will be paid by Atop.Atop shall not be held responsible for any consequential losses from using Atop’s product.Warranty PolicyThe warranty certification will not be effective until an authorized stamp issued by Atop’s overseas agents.Purchase Date: / / (yyyy/mm/dd)Serial NumberProduct CategoriesWarranty WarrantyProduct CategoriesMedia ConvertersEmbedded Device ServersEthernet SwitchesWirelessSerial Device ServersModbus Gateways 5 YearsProtocol GatewaysDIN-Rail Power Supplies 3 years1 yearsPower AdaptorsAntennasOther AccessoriesWarranty ConditionsRMA and Shipping Costs Reimbursement 1. Please contact your local dealers or Atop Technical Support Center at the following numbers. + 886-3-550-8137 (Atop Taiwan) + 86-21-6495-6232 (Atop China)2. Please report the defected problems via Atop’s Web site or E-mail account Web Site：www.atop.com.tw, e-mail：service@atop.com.tw Web Site：www.atop.com.cn, e-mail：service@atop.com.cn3. Company Addr: 2F, No. 146, Sec. 1, Tung-Hsing Rd., Jubei, Hsinchu 30261, Taiwan, R.O.C. Manufacturer Addr: 1st FL 30 R&D RD II,SCIENCE-BASED INDUSTRIAL PARK,HSINCHU 300 TAIWAN, R.O.CAtop Customer Services and SupportsLimited LiabilityProducts supplied by Atop Technologies are covered in this warranty for sub-standard performance or defective workmanship. The warranty is not, however, extended to goods damaged in the following circumstances:(a) Excessive forces or impacts(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake(c) Use of unqualified power supply, connectors, or unauthorized parts/kits(d) Replacement with unauthorized partsWarranty Period─ Any changes to this material will be announced on Atop website. ─

Navigation menu