ATrack Technology ATVT1304 UMTS GPS VEHICLE TRACKER User Manual
ATrack Technology Inc. UMTS GPS VEHICLE TRACKER
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2009494 |
| Application ID | B2GNiamFlHDa3QBXKh+fOw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 35.28kB (440949 bits) |
| Date Submitted | 2013-07-05 00:00:00 |
| Date Available | 2014-01-01 00:00:00 |
| Creation Date | 2017-10-26 18:45:44 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-26 18:45:44 |
| Document Title | User Manual |
| Document Creator | PScript5.dll Version 5.2.2 |
AK7 User Manual Revision: 05 Revision Date: 2012/06/25 ATrack Technology Inc. Tel: +886-2-27975852 3F., No. 88, Sec. 1, Neihu Rd., Neihu Dist., Fax: +886-2-27974030 Taipei City 11493, Taiwan (R.O.C.) http://www.atrack.com.tw Confidential Document Contents 1. Notification .............................................................................................................................. 3 1.1. Disclaimer .................................................................................................................................... 3 1.2. Copyright ...................................................................................................................................... 3 1.3. Warning ........................................................................................................................................ 3 2. Hardware ................................................................................................................................. 4 2.1. 2.2. 2.3. 2.4. 2.5. 2.6. 3. Package Content ......................................................................................................................... 4 SIM Card Installation .................................................................................................................... 4 Power I/O Connector ................................................................................................................... 5 Serial Port Connector................................................................................................................... 6 GPS Antenna ............................................................................................................................... 7 LED Indicators ............................................................................................................................. 8 Configuration .......................................................................................................................... 9 3.1. Connect device to HyperTerminal ................................................................................................ 9 3.2. Connect the device to the remote server ................................................................................... 13 4. 5. Firmware Upgrade ............................................................................................................... 14 Appendix................................................................................................................................ 15 5.1. Hardware Specification .............................................................................................................. 15 5.2. FCC Regulations:....................................................................................................................... 16 © ATrack Technology Inc. All Rights Reserved. Page 2 of 16 Confidential Document 1. Notification 1.1. Disclaimer This document, and all other related products, such as device, firmware, and software, is developed by ATrack Technology Inc. thoroughly. At the time of release, it is most compatible with specified firmware version. Due to the functionalities of the devices are being developed and improved from time to time, the change in the protocol, specification, and firmware functions are subjects to change without notice. ATrack Technology Inc. is obligated to modify all the documentation without the limitation of time frame. A change notice shall be released to ATrack Technology Inc. customers upon the completion of document modification. ATrack Technology Inc. products are not intended to be used as life support or rescue equipments. ATrack Technology Inc. is not liable for any loss or injury caused by using or referencing to any products. Any possible means of using or integrating ATrack Technology Inc. products shall be avoided. 1.2. Copyright ATrack Technology Inc. holds all parts of intellectual rights applicable in the copyright laws in all the countries. Any or all parts of this document shall not be exposed to non-authorized party without any form of approval from ATrack Technology Inc. Any forms, including but not limited to oral, copy, or internet sharing, of releasing or exposing information to an unauthorized party shall be prohibited. ATrack Technology Inc. reserves the rights of litigation in the violation of such copyright laws. 1.3. Warning Connecting the wire inputs can be hazardous to both the installer and your vehicle’s electrical system if not done by an experienced installer. This document assumes you are aware of the inherent dangers of working in and around a vehicle and have a working understanding of electricity. © ATrack Technology Inc. All Rights Reserved. Page 3 of 16 Confidential Document 2. Hardware 2.1. Package Content Each package contains the following device/accessories: Device * 1 (one of the devices below) AK7 GPS Antenna * 1 for AT1EONLY Power/IO Cable * 1 Serial Cable * 1 2.2. SIM Card Installation The AK7 supported 1.8V/3V universal SIM card which provided by worldwide GSM operators. Unscrew the SIM cover on the button of the AK7 device for SIM card installation. © ATrack Technology Inc. All Rights Reserved. Page 4 of 16 Confidential Document 2.3. Power I/O Connector The following figure shows power I/O connector and its pin number of AK7 Power I/O The following table shows its function of power I/O connector Power I/O Connector Pin# Function Color Designation Note Main power input Red PWR DC 9V~40V input Power ground Black GND ACC Input Yellow ACC Ignition status positive trigger input General Input1 Green IN1 Negative trigger input General Output1 Brown O1 Open collector output (Max.300mA) General Output2 Gray O2 Open collector output (Max.300mA) Positive Inputs: ACC (Triggered when connects to V+ range from 3.7 ~ 40V) Negative Inputs: IN1 (Triggered when connects to ground range from 0.8 ~ 0V) All outputs are open collector type (grounded when enabled) with max. sink current of 300mA. © ATrack Technology Inc. All Rights Reserved. Page 5 of 16 Confidential Document 2.4. Serial Port Connector The following figure shows serial port connector and its pin number of AK7 Serial Port The following table shows its function of serial port connector Serial Port Connector Pin# Function Color Designation Power Ground Black GND RS232 Transmit data output White TX RS232 Receive data input Green RX 4* +5V Output for external accessories Red +5V Note DC5V Max.300mA Output * Note that the +5V output pin cannot connect to the other power source or short circuit to power ground. If the connected accessory requires more power, please use external power source instead. The following figure shows the wire diagram of serial cable. © ATrack Technology Inc. All Rights Reserved. Page 6 of 16 Confidential Document 2.5. GPS Antenna The AK7 determines its position by communicating with the Global Positioning Satellites through GPS antenna. The location where the AK7 is installed will have great effect in the overall performance of the GPS receiver. The AK7 device has an internal GPS antenna but it is not a water proof design. Therefore, it shall not be installed outside of cabin or with the possibility of being splashed by water or rain . Ideally the label of AK7 should facing up (towards the sky) after the installation, such that the top of the device has a clear view of the sky. Mounting in this orientation provides optimum GPS signal reception. This face towards the sky Please note that the following interior conditions may cause bad GPS reception of AK7: Your vehicle has metallic window tint Your vehicle has a windshield mounted radio antenna Your vehicle has a solar reflective window © ATrack Technology Inc. All Rights Reserved. Page 7 of 16 Confidential Document 2.6. LED Indicators The following figure shows the location of the device LEDs. PWR GPS LED GSM Indication Description Solid On In full operation mode 1 blink (0.1 sec.) in every 10 sec. In sleep mode PWR (Green) GPS module off, External power lost, running on 1 sec. On, 1 sec. Off backup battery 0.7 sec. On, 0.7 sec. Off Searching GPS signal Solid On Position get fixed Off GSM module off 0.7 sec. On, 0.7 sec. Off Searching GSM signal 0.2 sec. On, 2 sec. Off Registered to GSM network 2 blinks in every 2 sec. Connected to GPRS network Continuous blinking SIM PIN Error GPS (Red) GSM (Red) Note: In the case of SIM PIN Error, the device will check the AT$SPIN every 10 minutes and try to access the SIM again. If the PIN is not corrected within 3 times of checking, including the first inserting time, the SIM card will be locked. Once the SIM is locked, you need to contact your GSM carrier for the PUK to unlock the SIM card on a cellular phone. © ATrack Technology Inc. All Rights Reserved. Page 8 of 16 Confidential Document 3. Configuration The device can be configured its parameters and behaviors by using AT commands. Please refer to ATrack Protocol Document for details. The device AT commands can be sent through RS232 port, SMS or GPRS TCP/UDP. 3.1. Connect device to HyperTerminal The HyperTerminal is one of the most popular RS232 Terminal Emulator in Windows Platform. The other similar RS232 terminal emulator software can perform the same result. The following example shows how to connect the device to the HyperTerminal. (1) Run HyperTerminal program and choose COM port and click [Configure…] button. © ATrack Technology Inc. All Rights Reserved. Page 9 of 16 Confidential Document (2) Choose 57600,8,N,1 None flow control properties and click [OK] button. (3) Click [File][Properties] © ATrack Technology Inc. All Rights Reserved. Page 10 of 16 Confidential Document (4) Click [Settings] tab and [ASCII Setup…] button (5) Checked the following options and click [OK] button © ATrack Technology Inc. All Rights Reserved. Page 11 of 16 Confidential Document (6) Power ON the device. The startup message will show on the screen. The device AT command can be sent through the terminal after device startup. © ATrack Technology Inc. All Rights Reserved. Page 12 of 16 Confidential Document 3.2. Connect the device to the remote server The GPRS connection shall be enabled and configured by AT$GPRS command. The ATrack ServerTool is a Windows-based software for GPRS connection testing. Once the GPRS has been enabled on the AK7device, the ServerTool will get connect to the AK7device. © ATrack Technology Inc. All Rights Reserved. Page 13 of 16 Confidential Document 4. Firmware Upgrade The AK7device firmware can be upgraded by using RS232 serial port communication or GPRS FTP protocol. The following is an example for how to upgrade firmware by serial port. (1) Run ATFWUpload program and select COM port and firmware file properly. Press [Open] button. (2) Power On the AK7device. The process will be started. (3) After the firmware has uploaded and verified successfully, the green completed message will be shown. © ATrack Technology Inc. All Rights Reserved. Page 14 of 16 Confidential Document 5. Appendix 5.1. Hardware Specification AK7 Physical Characteristics Dimension 80 * 48 * 26 mm UMTS Module Quad band GSM 850/900/1800/1900MHz Frequency Bands Tri‐band UMTS 850/1900/2100 MHz GPS Module High Sensitivity (65 Channel) GPS Antennas (for AT1E) SMA Connector Type Shock Sensor Built-In Real-Time Clock Built-In Memory Capacity 2MB Casing High Heat Grade ABS Electrical Characteristics Power Source 8-40 VDC Power Consumption Operational Sleep Deep Sleep 100 mA @ 12VDC 20 mA @ 12VDC 8 mA @ 12VDC I/O Characteristics Device I/O Ports Positive Input 1 (Triggering voltage: 3.7 ~ 40V) Negative Input 1 (Triggering voltage: 0 ~ 0.8V) Negative Outputs Serial Configurable Baud rates 2 (Open Collector Type @ 300mAMAX) 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps Environmental Characteristics Operation Temperature -30 ~ +70°C (Note: Temp. up to +85°C with extreme condition) Storage Temperature Relative Humidity © ATrack Technology Inc. All Rights Reserved. -40 ~ +85°C 5 ~ 95% Page 15 of 16 Confidential Document 5.2. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RF Exposure Information This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. © ATrack Technology Inc. All Rights Reserved. Page 16 of 16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : Create Date : 2013:05:28 11:16:12+08:00 Modify Date : 2013:06:27 16:53:02+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2013:06:27 16:53:02+08:00 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Creator : Title : Document ID : uuid:d94b23c8-0aab-48aa-86da-85318156ac1f Instance ID : uuid:bbe5e6f4-6097-4ddb-8f3c-b9337e9587f0 Page Count : 16EXIF Metadata provided by EXIF.tools