AUTOLAND SCIENTECH ISCANII-BU Car Diagnostician User Manual

AUTOLAND SCIENTECH Co. LTD Car Diagnostician

UserManual.wiki >

AUTOLAND SCIENTECH >

ISCANII BU User Manual

User Manual

1 SCANNER FEATURES 1. FEATURES Power supply indication light Status light indicator USB socket for Keypad for numbers for diagnostic circuits software update Display ScreenBluetooth Indication light Keypad for Directions

2 9-Pin Connector For connection to a PC or Thermal Printer 25-Pin Connector For connection with 25-Pin diagnostic adapter/cable. Interface Specified ConnectorThe connector for the special interface cards. 9-Pin Connector Used for attaching optional devices such as a personal computer or the thermal printer. Display Screen Displays data and messages for the user. Keypad Used for entering commands and selecting data on the scanner screen. USB Socket Download the software from the Internet and program the internal memory. Users should download the drivers and PS-Module Manager to program the software. Install the driver before start PS-Module Manager. Contrast Dial Used to adjust the brightness for the screen. Bluetooth Indication Light The blue light will flash without PC connection. Always ON when connected with PC. Ashtray Lighter Power / Battery Power Some diagnostic connector does not have power supply or ground. For such models users have to plug the ashtray lighter power cable or battery power cable together with the diagnostic cable. 25-Pin Connector For connection to the 25-Pin Diagnostic Cable Screen Brightness DialBluetooth Antenna Ashtray lighter power / Battery power, DC: 9-16VInterface specified connector

3 2. KEYPAD Left and Right arrow keys: Enables movement through diagnostic functions, vehicle models and systems from the current page to the NEXT or PREVIOUS page. Up and Down arrow keys: Used for selecting test functions, vehicle models and systems that are listed on the CURRENT page. Enter commands into the scanner. Interrupts the current procedure and returns to the previous menu or test mode selection. 0 ~ 9 Digits 0 through 9. Selects the functions, vehicle models or systems by pressing the numbered keys. 3. INDICATOR LIGHTS Power Indicator (Red LED light) Data Link Indicator (Green LED light) Data Link Indicator (Orange LED light). Bluetooth Status Indicator (Blue LED light) If the diagnostic link circuit is shorted to ground or if the control unit is faulty, the green or orange LED light will turn on steadily when the scanner is connected to the vehicle’s diagnostic connector.4. QUICK START (1) FIND THE DIAGNOSTIC CONNECTOR Most of the connectors are on the driver’s side below the dash board. Sometimes covered by a plastic plate. Please note that prior to the year 2000 most vehicles were equipped with manufacturer specific connector. Some manufacturers used different connectors to access different systems. Ex: Toyota. These connectors are located in the engine compartment. To retrieve manufacturer information, please connect to the appropriate port, failure to do so will result in a communication error.

4 (2) SELECT THE INTERFACE MODULE There are some interface modules available. For example, OBDII-IM5. Insert the interface module into the base unit. WARNING! Wrong selection may be harmful for the vehicle or fail to communicate. (3) CONNECT TO THE VEHICLE Connect the iSCAN-II and the diagnostic connector in the vehicles. Find the models from the screen of iSCAN-II. Press ENTER to start the diagnostic function. If the model is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page.

5 5. ICONS Along the top or bottom of the display, the following icons may appear which will provide more information to the user. DATA STREAM 3/8 Engine Speed 915 rpmCoolant Temperature 85 ºC Injection Time 10 ms Ignition Angle 5 º Battery Voltage 13.2 V Electric Load ON Brake Signal OFF Page Keys When either of these icons appears in the top line or bottom line on the screen, there is more information available. Press the (left), (right), (down), and (up) arrow key to view additional information. 0..9 Number Keys 1. Press the Number key from 1 to 9 to directly select the vehicle make or system items. 3/8 Page Information Displays current page number and total number of pages. Connecting Failed Faulty Connection Indication  Check and see if the Ignition key is on or if the engine is running. Check the power requirement for the scanner (10.5 to 14.5 Volts) Check and make sure that the connection to the vehicle’s diagnostic connector is secure.  Check for a short circuit in the vehicle’s diagnostic connector.  Check and make sure that the cartridge in use supports this vehicle’s system.  Check to make sure that you have selected the correct cables.

iSCAN-II DocumentationACURA® HONDA® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for ACURA / HONDA diagnostic system. Prior to theyear 1998, most vehicles were equipped with 3-Pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. The rest of sockets may be located under the glove compartment on passenger side or close to the side kicker on driver's. Please refer to the sticker direction under the dashboard on driver side and near the steering column. The socket may locate at the following position.The diagnostic socket is located under the dashboard on driver side, near the left side of thesteering column. For example ACCORD (’98-03), CIVIC (’96-00), PASSPORT (96-99).The diagnostic socket is located in the central console. It is under the ashtray. (Remove theashtray). For example, ACCORD (‘95-97).The vehicle’s diagnostic socket is located under the glove compartment. For example, S2000(00-03), Pilot (‘03)The vehicle’s diagnostic socket is located on the right side of the central console, near thepassenger’s glove compartment. For example, DEL SOL, CR-X (’96-97), ODYSSEY (’96-98),PRELUDE, CR-V (‘97-01), INSIGHT (’00-02). Note: To connect PRELUDE (’97-01), remove thetrim panel.The diagnostic socket is located under the armrest. To connect, remove the beverage holder.For example, PRELUDE (‘96).The diagnostic socket is located under the dashboard on driver side , near the right side of thesteering column. For example, CIVIC (’01-03), ODYSSEY (’99-03), CR-V (‘02-03)3-PIN Soc ket For the older models which were not equipped with OBD-II socket, there is a 3-PIN socket available. Please refer to the sticker direction under the dashboard on driver side and near the steering column. The diagnostic socket is located under the glove compartment on passenger side. It is veryclose to side kicker. For example, CIVIC, CR-X (‘92-95), DEL SOL (‘93-95)The diagnostic socket is located in the central console. It is above the ashtray or coin tray. Forexample, PRELUDE (‘92-95).The diagnostic socket is located in the central console. It is under the ashtray or coin tray. Forexample, PASSPORT (‘94-95/5)The diagnostic socket is located under the glove compartment on passenger side. It is near theside kicker. For example, ACCORD (‘94-95 L4)The diagnostic socket is located under the glove compartment. For example, ODYSSEY (’95).iSCAN-II for ACURA / HONDA © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECHACURA / HONDA

2. SELECT THE INTERFACE MODULEThere is only one interface module available for ACURA / HONDA diagnostic system, OBDII-IM5. Insert the interface module into the base unit firmly. Select the adapter that corresponds tothe socket, ex. OBDII-AC-16P.3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theACURA / HONDA from the screen of iSCAN-II. Press ENTER to start the diagnostic function. Ifthe model is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 ACURA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 ISUZU iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for ACURA / HONDA © 2008 Autoland Scientech. Page 2ACURA / HONDA

ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16POBD-II Full Specification Multiplexer The most common adapter for the new models.Connect to the OBDII-IM5 with AC-EC1.HND-AC-3P HND-C-2PThe adapter for the old models. The adapter to trigger the self-test light at theinstrument cluster.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for ACURA / HONDA © 2008 Autoland Scientech. Page 3ACURA / HONDA

START TO DIAGNOSEACURA and HONDA vehicles are equipped with the same diagnostic systems. Select ACURA orHONDA may have the same functions for the diagnostic system.Select ACURA or HONDA by pressing the ENTER button. Turn ignition ON or make engine running atidle. WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.ACURA   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS / VST4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAM5 CLEAR ADAPTATION6 2-PIN CODE LOOKUP 6 ECU RESETThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for ACURA / HONDA. Please refer tothe software specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for ACURA / HONDA © 2008 Autoland Scientech. Page 4ACURA / HONDA

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for ACURA / HONDA © 2008 Autoland Scientech. Page 5ACURA / HONDA

iSCAN-II DocumentationBMW® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for BMW diagnostic system. From 1987 to 2000, themodels were equipped with round type 20-Pin diagnostic socket. The models since 2001 havebeen equipped with OBD-II socket.OBD- II Socket For the newer models, ex. E65, E60, E90...etc, OBD-II diagnostic socket can be found under a plastic cover of dashboard on driver side. It is very close to side kicker and near the door. US models from 1995 to 2000 were equipped with both 20-Pin and OBD-II diagnostic sockets. Only20-PIN diagnostic socket can work in the diagnostic communication. OBD-II diagnostic socket isfor Generic OBD-II communication purpose only. OBD-II socket20-PIN SocketThe oldest models equipped with 20-PIN socket. The socket is covered by a plastic cover and under the engine hood, beside the absorber strut tower. 20-PIN socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for BMW diagnostic system, OBDII-IM5. Insert theinterface module into the base unit firmly if the socket in the vehicle is OBD-II, and connect theadapter that corresponds to the socket, OBDII-AC-16P. iSCAN-II for BMW © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH BMW Diag

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select the BMWDiag from the screen of iSCAN-II. Press ENTER to start the diagnostic function. If the model isnot listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>BMW GT21 <BMW GT2> 1 BMW Diag iSCAN-II (V1.00)2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4 FIAT iSCAN-II (V1.00)2 BMW CODING iSCAN-II (V1.00) 3 BMW SSS iSCAN-II (V1.00)4. MINI 5 JAGUAR iSCAN-II (V1.00)6 LANDROVER iSCAN- II (V1.00) iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16P BM-AC1-20PInsert this interface module forthe models equipped with onlyOBD-II socket.The most common adapter forthe new models from 2001.Connect to the OBDII-IM5 withAC-EC1.The adapter for the old modelsup to 2000. Connect directly toiSCAN-II using BU-EC. There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for BMW © 2008 Autoland Scientech. Page 2 BMW Diag

START TO DIAGNOSESelect BMW Diag by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.BMW Diag  DME 7.2  1 1 series 1 ID CODES2 3 series 2 READ FAULT CODE3 5 series4 6 series5 7 series3 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATION6 X series 6 ADAPTATION7 EWS / DME Sync8 CAS / DME SyncThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for BMW. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for BMW © 2008 Autoland Scientech. Page 3 BMW Diag

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there is no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connects to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. After selecting the model, the green light is always ON before communication starts? If the diagnostic circuit is shorted to ground or if a faulty control unit is in the vehicle, the green or yellow LED light on the scanner will remain on steadily when the scanner is connected to the vehicle diagnostic connector. Try to remove the faulty ECU from the bus.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for BMW © 2008 Autoland Scientech. Page 4 BMW Diag

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select theCHRYSLER from the screen of iSCAN-II . Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN>1 <KOREA>2 <JAPAN>3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~) MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full Specification Multiplexer The most common adapter for the newmodels. Connect to the OBDII-IM5 withAC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.ISCAN-II for CHRYSLER © 2008 Autoland Scientech. Page 2 CHRYSLER

START TO DIAGNOSESelect CHRYSLER by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.CHRYSLER   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for CHRYSLER. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.ISCAN-II for CHRYSLER © 2008 Autoland Scientech. Page 3 CHRYSLER CHRYSLER

TROUBLE SHOTTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.ISCAN-II for CHRYSLER © 2008 Autoland Scientech. Page 4 CHRYSLER

iSCAN-II DocumentationCITROËN® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under a plastic cover of dashboard on driver side.Some of them can be found behind the ashtray box or the relay box.OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for CITROËN diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly if the socket in the vehicle is OBD-II, andconnect the adapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for CITROËN © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH CITROËN

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theCITROEN from the screen of iSCAN-II. Press ENTER to start to diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>FRENCH PKG1 <BMW GT2>2 <FRENCH PKG>1 RENAULT iSCAN-II (V1.00)3 MB iSCAN-II (V1.00)4. FIAT2 CITROEN iSCAN-II (V1.00)3 PEUGEOT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00) iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for the modelsequipped with only OBD-II socket.The most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for CITROËN © 2008 Autoland Scientech. Page 2 CITROËN

START TO DIAGNOSESelect CITROËN by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.CITROEN   ENGINE  1 BERLINGO 1 ID CODES2 C2 2 READ FAULT CODE3 C34 C45 C53 CLEAR FAULT CODE4 DATA STREAM6 C87 JUMPY8 XSARAThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for CITROËN. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for CITROËN © 2008 Autoland Scientech. Page 3 CITROËN

TROUBLE SHOOTINGiSCAN-II never show anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connects to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for CITROËN © 2008 Autoland Scientech. Page 4 CITROËN

iSCAN-II DocumentationDAEWOO® DIAGNOSTIC SYSTEMGETTING STARTEDiSCAN- II Daewoo Diagnostic Software focus on Daewoo except GM Daewoo vehicles. GM Daewoo, please select iSCAN-II GM Diagnostic Software for North America area.1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for DAEWOO diagnostic system. Prior to the year1998, most vehicles were equipped with 12-Pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. OBD-II socket12-PIN Soc ket For the old models equipped with 12-PIN socket, please refer to the sticker direction under thedashboard on driver side and near the steering column. Some models equip both of thesockets, only 12-PIN socket can be worked.2. SELECT THE INTERFACE MODULEThere is only one interface module available for DAEWOO diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly. Select the adapter that corresponds to thesocket, ex. OBDII-AC-16P.iSCAN-II for DAEWOO © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH DAEWOO

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theDAEWOO from the screen of iSCAN-II . Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><KOREA>1 <KOREA>2 <JAPAN>1 DAEWOO iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 HYUNDAI iSCAN-II (V1.00)3 KIA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 SSANGYONG iSCAN-II (V1.00) iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16P GM-AC-12POBD-II Full SpecificationMultiplexerThe most common adapter for thenew models. Connect to theOBDII-IM5 with AC-EC1.The adapter for the old models.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for DAEWOO © 2008 Autoland Scientech. Page 2 DAEWOO

START TO DIAGNOSESelect DAEWOO by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.DAEWOO   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for DAEWOO. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for DAEWOO © 2008 Autoland Scientech. Page 3 DAEWOO

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.1. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for DAEWOO © 2008 Autoland Scientech. Page 4 DAEWOO

iSCAN-II DocumentationDAIHATSU® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Socket The OBD-II diagnostic socket is located under the steering wheel on driver side. OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for DAIHATSU diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly. Select the adapter that corresponds to thesocket, ex. OBDII-AC-16P.iSCAN-II for DAIHATSU © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH DAIHATSU

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select theDAIHATSU from the screen of iSCAN- II . Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 ACURA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 ISUZU iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full SpecificationMultiplexerThe most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for DAIHATSU © 2008 Autoland Scientech. Page 2 DAIHATSU

START TO DIAGNOSESelect DAIHATSU by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.DAIHATSU   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for DAIHATSU. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for DAIHATSU © 2008 Autoland Scientech. Page 3 DAIHATSU

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for DAIHATSU © 2008 Autoland Scientech. Page 4 DAIHATSU

iSCAN-II DocumentationFIAT® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover.OBD-II socketOther Soc ket iSCAN-II FIAT Diagnostic Software does not support the vehicles which are equipped with the other sockets.2. SELECT THE INTERFACE MODULEThere is only one interface module available for FIAT diagnostic system, OBDII-IM5. Insert theinterface module into the base unit firmly if the socket in the vehicle is OBD-II, and connect theadapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for FIAT © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH FIAT

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select the FIATfrom the screen of iSCAN-II . Press ENTER to start to diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter for the newmodels. Connect to the OBDII-IM5 withAC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for FIAT © 2008 Autoland Scientech. Page 2 FIAT

START TO DIAGNOSESelect FIAT by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.FIAT   TRANSMISSION  1 ENGINE 1 ID CODES2 TRANSMISSION 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for FIAT. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for FIAT © 2008 Autoland Scientech. Page 3 FIAT

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software do not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connects to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for FIAT © 2008 Autoland Scientech. Page 4 FIAT

iSCAN-II Documentation!!!!FORD® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side.OBD-II socketOTHER SocketIf another connector is found, ex. 17+8 / 6+1 / 20-PIN socket, please select iSCAN-II MAZDA Diagnostic Software.2. SELECT THE INTERFACE MODULEThere is only one interface module available for FORD diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly. Select the adapter that corresponds to the socket,ex. OBDII-AC-16P.ISCAN-II for FORD © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH FORD

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select the FORDfrom the screen of iSCAN- II . Press ENTER to start the diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN>1 <KOREA>2 <JAPAN>3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~) MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full SpecificationMultiplexerThe most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.ISCAN-II for FORD © 2008 Autoland Scientech. Page 2 FORD

START TO DIAGNOSESelect FORD by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.FORD   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for FORD. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.ISCAN-II for FORD © 2008 Autoland Scientech. Page 3 FORD

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connects to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.ISCAN-II for FORD © 2008 Autoland Scientech. Page 4 FORD

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select the GMfrom the screen of iSCAN- II . Press ENTER to start the diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN>1 <KOREA>2 <JAPAN>3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~) MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full Specification Multiplexer The most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.ISCAN-II for GM © 2008 Autoland Scientech. Page 2 GM

START TO DIAGNOSESelect GM by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions. GM   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for GM. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.ISCAN-II for GM © 2008 Autoland Scientech. Page 3 GM GM

TROUBLE SHOTTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything in LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then shows 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.ISCAN-II for GM © 2008 Autoland Scientech. Page 4 GM

iSCAN-II DocumentationHYUNDAI® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for HYUNDAI diagnostic system. Prior to the year2000, most vehicles were equipped with 12-Pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. For new models after 2006, the communication protocol of ECUs is CAN. Please use OBDII-IM5 first on new models, then try ASIAN-IM1 if the communication with some systems are failed.OBD-II socket12-PIN Soc ket For the old models equipped with 12-PIN round socket, located in the fuse box under the steering wheel on driver side. Some models may be equipped with OBD-II and 12-PIN connectors together. Try both connectors by using ASIAN-IM1.2. SELECT THE INTERFACE MODULEThere are two interface modules available for HYUNDAI diagnostic system, OBDII-IM5 andASIAN-IM1. Insert the interface module into the base unit firmly. Select the adapter thatcorresponds to the socket, ex. OBDII-AC-16P.iSCAN-II for HYUNDAI © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH HYUNDAI

3. CONNECT TO THE VEHICLEPlug the diagnostic adapter into the diagnostic socket in the vehicle. Select the HYUNDAI fromthe screen of iSCAN- II . Press ENTER to start to diagnostic function. If the model is not listed onthe screen, try to press RIGHT / LEFT buttons to turn the page. If the model equipped with 12-PIN diagnostic socket, plug the ashtray lighter power cable, BU-EC-1. 12-PIN diagnosticconnector should connect to ASIAN-IM1, MIT port.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><KOREA>1 <KOREA>2 <JAPAN>1 DAEWOO iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 HYUNDAI iSCAN-II (V1.00)3 KIA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 SSANGYONG iSCAN-II (V1.00) iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for HYUNDAI © 2008 Autoland Scientech. Page 2 HYUNDAI

ADAPTERS AND INTERFACE MODULEThere are two interface modules available for the diagnostic system, OBDII-IM5 and ASIAN-IM1.OBDII-IM5 ASIAN-IM1OBD-II Full Specification Multiplexer ASIAN Interface Module for TOYOTA / NISSAN /MITSUBISHI / HYUNDAI / KIAOBDII-AC-16P MIT-AC-12P BU-EC-1The most common adapter forthe new models. Connect to theOBDII-IM5 or ASIAN-IM1 withAC-EC1.The adapter for the old models.Connect to the ASIAN-IM1 withAC-EC1.Ashtray lighter power cable, thepower source for 12-PINdiagnostic socket models.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for HYUNDAI © 2008 Autoland Scientech. Page 3 HYUNDAI

START TO DIAGNOSESelect HYUNDAI by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.HYUNDAI   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATIONThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for HYUNDAI. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for HYUNDAI © 2008 Autoland Scientech. Page 4 HYUNDAI

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. For models manufactured at 2006, which interface module should I insert?Try OBDII-IM5 first, then ASIAN-IM1. OBDII-IM5 is applicable to CAN-protocol, and ASIAN-IM1 is to HYUNDAI specific protocol. To connect with CAN-protocol models, ASIAN-IM1 maysend traditional signals to interrupt the inter-connection of the CAN-bus and cause fault codes. Please use OBDII-IM5 with iSCAN-II HYUNDAI diagnostic software to clear the fault codes.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for HYUNDAI © 2008 Autoland Scientech. Page 5 HYUNDAI

iSCAN-II DocumentationINFINITI® NISSAN® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for INFINITI / NISSAN diagnostic system. Please notethat prior to the year 1998, most vehicles are equipped with 14-Pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. For new models after 2006, the communication protocol of ECUs is CAN. Please use OBDII-IM5 first on new models, then try ASIAN-IM1 if the communication with some systems are failed.14-PIN Soc ket For the old models equipped with 14-PIN round socket, located in the fuse box under the steering wheel on driver side. Some models might be equipped with OBD-II and 14-PIN connectors together, only 14-PIN diagnostic socket can be worked.2. SELECT THE INTERFACE MODULEThere are two interface modules available for INFINITI / NISSAN diagnostic system, OBDII-IM5and ASIAN-IM1. Insert the interface module into the base unit firmly. Select the adapter thatcorresponds to the socket, ex. OBDII-AC-16P.iSCAN-II for INFINITI / NISSAN © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH INFINITI / NISSAN

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select theINFINITI or NISSAN from the screen of iSCAN-II. Press ENTER to start the diagnosticfunction. If the model is not listed on the screen, try to press RIGHT / LEFT buttons to turn thepage.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 NISSAN iSCAN-II (V1.00) iSCAN-II (V1.00) 5 INFINITI iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for INFINITI / NISSAN © 2008 Autoland Scientech. Page 2 INFINITI / NISSAN

ADAPTERS AND INTERFACE MODULEThere are two interface modules available for the diagnostic system, OBDII-IM5 and ASIAN-IM1.OBDII-IM5 ASIAN-IM1OBD-II Full Specification Multiplexer ASIAN Interface Module for TOYOTA /NISSAN / MITSUBISHI / HYUNDAI / KIAOBDII-AC-16P NSN-AC-14PThe most common adapter for the newmodels. Connect to the OBDII-IM5 orASIAN-IM1 with AC-EC1.The adapter for the old models. Connectto the ASIAN-IM1 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for INFINITI / NISSAN © 2008 Autoland Scientech. Page 3 INFINITI / NISSAN

START TO DIAGNOSESelect NISSAN or INFINITI by pressing the ENTER button. Turn ignition ON or make engine running atidle. WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.INFINITI   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS / VST4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAM5 CLEAR ADAPTATION6 2-PIN CODE LOOKUP 6 ECU RESETThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for INFINITI / NISSAN. Please refer tothe software specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for INFINITI / NISSAN © 2008 Autoland Scientech. Page 4 INFINITI / NISSAN INFINITI / NISSAN

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.For models manufactured at 2006, which interface module should I insert?Try OBDII-IM5 first, then ASIAN-IM1. OBDII-IM5 is applicable to CAN-protocol, and ASIAN-IM1 is to INFINITI / NISSAN specific protocol. To connect with CAN-protocol models, ASIAN-IM1 may send traditional signals to interrupt the inter-connection of the CAN-bus and causefault codes. Please use OBDII-IM5 with iSCAN-II INFINITI / NISSAN diagnostic software toclear the fault codes. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for INFINITI / NISSAN © 2008 Autoland Scientech. Page 5 INFINITI / NISSAN

iSCAN-II DocumentationISUZU® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Socket The OBD-II diagnostic socket is located under the steering wheel on driver side. OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for ISUZU diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly. Select the adapter that corresponds to the socket,ex. OBDII-AC-16P.iSCAN-II for ISUZU © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH ISUZU

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select the ISUZUfrom the screen of iSCAN- II . Press ENTER to start the diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 ACURA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 ISUZU iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full Specification Multiplexer The most common adapter for the new models.Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for ISUZU © 2008 Autoland Scientech. Page 2 ISUZU

START TO DIAGNOSESelect ISUZU by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.ISUZU   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for ISUZU. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for ISUZU © 2008 Autoland Scientech. Page 3 ISUZU

TROUBLE SHOOTINGiSCAN-II never show anything in LCD screen and no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for ISUZU © 2008 Autoland Scientech. Page 4 ISUZU

iSCAN-II DocumentationJAGUAR® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover.OBD-II socketOther Soc ket iSCAN-II JAGUAR Diagnostic Software does not support the vehicles which are equipped with the other sockets.2. SELECT THE INTERFACE MODULEThere is only one interface module available for JAGUAR diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly if the socket in the vehicle is OBD-II, and connectthe adapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for JAGUAR © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH JAGUAR

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theJAGUAR from the screen of iSCAN-II . Press ENTER to start to diagnostic function. If the modelis not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for JAGUAR © 2008 Autoland Scientech. Page 2 JAGUAR

START TO DIAGNOSESelect JAGUAR by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.JAGUAR   TRANSMISSION  1 ENGINE 1 ID CODES2 TRANSMISSION 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for JAGUAR. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for JAGUAR © 2008 Autoland Scientech. Page 3 JAGUAR

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software do not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but show 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for JAGUAR © 2008 Autoland Scientech. Page 4 JAGUAR

iSCAN-II DocumentationKIA® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for KIA diagnostic system. Please note that prior tothe year 1998, most vehicles were equipped with 20-Pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. 20-PIN Soc ket For the old models equipped with 20-PIN socket, located in the engine compartment, beside the driver side absorber strut tower or relay / fuse box.2. SELECT THE INTERFACE MODULEThere are two interface modules available for KIA diagnostic system, OBDII-IM5 and ASIAN-IM1. Insert the interface module into the base unit firmly. Select the adapter that corresponds tothe socket, ex. OBDII-AC-16P.iSCAN-II for KIA © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH KIA

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select the KIAfrom the screen of iSCAN- II . Press ENTER to start the diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><KOREA>1 <KOREA>2 <JAPAN>1 DAEWOO iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 HYUNDAI iSCAN-II (V1.00)3 KIA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 SSANGYONG iSCAN-II (V1.00) iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for KIA © 2008 Autoland Scientech. Page 2 KIA

ADAPTERS AND INTERFACE MODULEThere are two interface modules available for the diagnostic system, OBDII-IM5 and ASIAN-IM1. OBDII-IM5 ASIAN-IM1OBDII-IM5 is for CAN-BUS protocolonly.Select ASIAN-IM1 with MIT port first.OBDII-AC-16P KIA-AC-20PThe most common adapter for the newmodels. Connect to the OBDII-IM5 orASIAN-IM1 with AC-EC1.The adapter for the old models. Connectto ASIAN-IM1 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for KIA © 2008 Autoland Scientech. Page 3 KIA

START TO DIAGNOSESelect KIA by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.KIA   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for KIA. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for KIA © 2008 Autoland Scientech. Page 4 KIA KIA

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.For models manufactured at 2006, which interface module should I insert?Try OBDII-IM5 first, then ASIAN-IM1. OBDII-IM5 is applicable to CAN-protocol, and ASIAN-IM1 is to KIA specific protocol. To connect with CAN-protocol models, ASIAN-IM1 may sendtraditional signals to interrupt the inter-connection of the CAN-bus and cause fault codes.Please use iSCAN-II KIA diagnostic software to clear the fault code.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for KIA © 2008 Autoland Scientech. Page 5 KIA

iSCAN-II DocumentationLANDROVER® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover.OBD-II socketOther Soc ket iSCAN-II LANDROVER Diagnostic Software does not support the vehicles which are equipped with the other sockets.2. SELECT THE INTERFACE MODULEThere is only one interface module available for LANDROVER diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly if the socket in the vehicle is OBDII, andconnect the adapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for LANDROVER © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH LANDROVER

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theLANDROVER from the screen of iSCAN-II . Press ENTER to start to diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for LANDROVER © 2008 Autoland Scientech. Page 2 LANDROVER

START TO DIAGNOSESelect LANDROVER by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.LANDROVER   TRANSMISSION  1 ENGINE 1 ID CODES2 TRANSMISSION 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for LANDROVER. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for LANDROVER © 2008 Autoland Scientech. Page 3 LANDROVER

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connects to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connect to the system but show 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for LANDROVER © 2008 Autoland Scientech. Page 4 LANDROVER

iSCAN-II DocumentationLEXUS® TOYOTA® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are three kinds of diagnostic sockets for LEXUS / TOYOTA. Please note that prior to theyear 1998, most vehicles are equipped with 17-Pin round socket or 23-Pin square socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. The connector of some models can be found behind the coin box / ashtray box. For new models after 2006, the communication protocol of ECUs is CAN. Please use OBDII-IM5 first on new models, then try ASIAN-IM1 if the communication with some systems are failed.17-PIN Round Soc ket For the older models equipped with 17-PIN round socket, located under the steering wheel on driver side. Some models might be equipped with OBD-II and 17-PIN connectors together. Try both connectors for each system. For these models, only ASIAN-IM1 interface module is available.23-PIN Square Soc ket For the old models which equipped with 23-PIN square socket, located in the engine compartment, beside driver side or passenger side absorber strut tower. Some models might be equipped with OBD-II, 17-PIN, 23-PIN connectors together. Try all connectors for each system. For those models, only ASIAN-IM1 interface module is available.2. SELECT THE INTERFACE MODULEThere are two interface modules available for LEXUS / TOYOTA diagnostic system, OBDII-IM5and ASIAN-IM1. Insert the interface module into the base unit firmly. Select the adapter thatcorresponds to the socket, ex. OBDII-AC-16P.iSCAN-II for LEXUS / TOYOTA © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH LEXUS / TOYOTA

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diangostic socket in the vehicles. Select theLEXUS or TOYOTA from the screen of iSCAN-II. Press ENTER to start the diagnostic function.If the model is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 TOYOTA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 LEXUS iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for LEXUS / TOYOTA © 2008 Autoland Scientech. Page 2 LEXUS / TOYOTA

ADAPTERS AND INTERFACE MODULEThere are two interface modules available for the diagnostic system, OBDII-IM5 and ASIAN-IM1.OBDII-IM5 ASIAN-IM1OBD-II Full Specification Multiplexer ASIAN Interface Module for TOYOTA / NISSAN /MITSUBISHI / HYUNDAI / KIAOBDII-AC-16P TYT-AC-17P TYT-AC-23PThe most common adapter forthe new models. Connect to theOBDII-IM5 or ASIAN-IM1 withAC-EC1.The adapter for the old models.Connect to the ASIAN-IM1 withAC-EC1.The adapter for the oldestmodels. Connect to the ASIAN-IM1 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for LEXUS / TOYOTA © 2008 Autoland Scientech. Page 3 LEXUS / TOYOTA

START TO DIAGNOSESelect TOYOTA / LEXUS by pressing the ENTER button. Turn ignition ON or make engine running atidle. WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.LEXUS   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS / VST4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAM5 CLEAR ADAPTATION6 2-PIN CODE LOOKUP 6 ECU RESETThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for TOYOTA / LEXUS. Please refer tothe software specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for LEXUS / TOYOTA © 2008 Autoland Scientech. Page 4 LEXUS / TOYOTA LEXUS / TOYOTA

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-IInever shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. For models manufactured at 2006, which interface module should I insert?Try OBDII-IM5 first, then ASIAN-IM1. OBDII-IM5 is applicable to CAN-protocol, and ASIAN-IM1 is to LEXUS / TOYOTA specific protocol. To connect with CAN-protocol models, ASIAN-IM1may send traditional signals to interrupt the inter-connection of the CAN-bus and cause faultcodes. Please use OBDII-IM5 with iSCAN-II LEXUS / TOYOTA diagnostic software to clear thefault codes.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for LEXUS / TOYOTA © 2008 Autoland Scientech. Page 5 LEXUS / TOYOTA

iSCAN-II DocumentationMAZDA® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETMazda is a partial subsidiary of Ford Motor Company. The Mazda software only covers on oldcars with old sockets, ex. 17+8 pin, 6+1 pin and 20-pin. For new Mazda, please select iSCAN-IIFORD Diagnostic Software. OBD- II Socket IF YOU FIND OBDII SOCKET, PLEASE SELECT iSCAN-II FORD DIAGNOSTIC SOFTWARE.Most OBD-II diagnostic sockets are located under the steering wheel on driver side. The connector can be found behind the coin box / ashtray box for some models..17+8 PIN Round Soc ket For the old models which were not equipped with OBD-II socket, there is a 17+8 PIN round socket available. Most the 17-PIN round sockets are located under the steering wheel on driver side. The diagnostic socket in some models are located in the engine compartment, beside the driver side or passenger side absorber strut tower. Some models will equip with OBD-II and 17-PIN connectors together, but only 17+8 PIN socket can be worked. For these models, only ASIAN-IM1 interface module is available.6+1 PIN / 20-PIN Soc ket The diagnostic socket is located in the engine compartment, beside the driver side or passengerside absorber strut tower. Connect the diagnostic socket to the base unit with BU-EC cable. Thepin location will be shown on the screen of iSCAN-II.2. SELECT THE INTERFACE MODULEThere is only one interface module available for Mazda diagnostic system, ASIAN-IM1. Insertthe interface module into the base unit firmly IF THERE IS A 17+8 PIN SOCKET IS FOUND,connect to TYT-connector. For 6+1 pin and 20-pin socket, connect directly with BU-EC cable.iSCAN-II for MAZDA © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH MAZDA

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theMAZDA from the screen of iSCAN-II. Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN>1 <KOREA>2 <JAPAN>3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~) MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, ASIAN-IM1.ASIAN-IM1 MAZ-AC-17P D51-C1-2P-MAZFor 17+8 PIN socket For 17+8 connector. BECAREFUL!! TYT-AC-17P isalmost the same as MAZ-AC-17P and it will NOT work forMazda vehicle.The adapter for the old modelsequipped with 6+1/20 pin socket.Connect directly to the base unitwith BC-EC.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for MAZDA © 2008 Autoland Scientech. Page 2 MAZDA

START TO DIAGNOSESelect MAZDA by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.MAZDA   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS / VST4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAM6 2-PIN CODE LOOKUPThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for MAZDA. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for MAZDA © 2008 Autoland Scientech. Page 3 MAZDA MAZDA

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for MAZDA © 2008 Autoland Scientech. Page 4 MAZDA

iSCAN-II DocumentationMERCEDES BENZ® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic sockets are located under the steering wheel on driver side and are covered by a plastic cover. US models from 1995 to 2000 were equipped with both 38-Pin and OBD-II diagnostic sockets. Only 38-PIN diagnostic socket can work in the diagnostic communication. OBD-II diagnostic socket is for Generic OBD-II communication purpose only. OBD-II socket38-PIN Soc ket For the old models from 1990 to 2001 equipped with 38-PIN socket. The socket is covered by a plastic cover, close to the firewall of engine compartment or near the either side of engine compartment. The diagnostic socket for the van may be found under the driver's seat.38-PIN socket16-PIN / 8-PIN Soc ket For the oldest models, like 107/124/126 and etc., equipped with 16-PIN or 8-PIN socket, the socket is near the firewall of engine compartment.16-PIN pole socket 8-PIN pole socketiSCAN-II for Mercedes Benz © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH MERCEDES BENZ

9-Pole Diagnostic Socket The old models were equipped with 9-Pole diagnostic socket. Using On-Off Ratio Meter or Multimeter with duty cycle scale to read out the On-Off Ratio fault codes from Pole 3 of the diagnostic socket. 9-Pole socket Access trouble codes:  Ensure ignition switched OFF.  Connect Multimeter between data link connector (DLC) Pole 3 and earth.  Switch ignition ON. Check that Multimeter indicates 70%. This indicates that the system has a fault memory.  Start engine. Allow to idle.  If readout fluctuates: No trouble codes have been recorded.  If readout does not fluctuate: Note trouble codes. Compare with trouble table.  Switch ignition OFF. Trouble code identification: (Ex. Model W126, 1985-1991, Engine: at idle)Percentage code: engine idling Fault location0% Data link connector (DLC) - wiring0% Weak mixture – with catalyst10% Closed throttle position (CTP) switch/volume air flow (VAF)sensor20% Wide open throttle (WOT) switch30% Engine coolant temperature (ECT) sensor40% Volume air flow (VAF) sensor 50% Oxygen sensor (O2S) – with cat50% No fault – without catalyst60% Vehicle speed sensor (VSS), during dynamic testing only70% Engine speed (RPM) sensor80% Intake air temperature (IAT) sensor (9/89-)/barometricpressure (BARO) sensor90% Differential pressure regulator95% Overrun cut-off active100% Rich mixture/O2S – with cat100% Engine control module (ECM) – supply voltageiSCAN-II for Mercedes Benz © 2008 Autoland Scientech. Page 2 MERCEDES BENZ

2. SELECT THE INTERFACE MODULEThere are only two interface modules available for MERCEDES BENZ diagnostic system,OBDII-IM5 and MB38-IM2. Insert the interface module into the base unit firmly. Select theadapter that corresponds to the socket, ex. OBDII-AC-16P.3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select the MBfrom the screen of iSCAN-II. Press ENTER to start to diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for Mercedes Benz © 2008 Autoland Scientech. Page 3 MERCEDES BENZ

ADAPTERS AND INTERFACE MODULEThere are two interface modules available for the diagnostic system, OBDII-IM5 and MB38-IM2.Select the interface module corresponds to the socket found in the vehicle.OBDII-IM5 MB38-IM2OBD-II Full Specification Multiplexer. Mercedes-Benz 38-Pin Electronic Multiplexer forold models from Year 1990 to 2001.OBDII-AC-16P MB-C-38P D51-C-MBLVThe most common adapter forthe new models. Connect to theOBDII-IM5 with AC-EC1.The adapter for the old models. The adapter for the oldestmodels. Connect directly to theiSCAN-II base unit.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for Mercedes Benz © 2008 Autoland Scientech. Page 4 MERCEDES BENZ

START TO DIAGNOSESelect MB by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.MB   HFM  1 S-Class 1 ID CODES2 E-Class 2 READ FAULT CODE3 C-Class4 ML-Class5 SL-Class3 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATION6 A-Class 6 WAVEFORM7 CODING8 ADAPTATIONThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for Mercedes-Benz. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for Mercedes Benz © 2008 Autoland Scientech. Page 5 MERCEDES BENZ

TROUBLE SHOTTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for Mercedes Benz © 2008 Autoland Scientech. Page 6 MERCEDES BENZ

iSCAN-II DocumentationMINI® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBDII diagnostic socket can be found under the dashboard on driver side and are coveredby a plastic cover. OBD-II socketOther Soc ket iSCAN-II MINI Diagnostic Software does not support the vehicles which are equipped with the other sockets.2. SELECT THE INTERFACE MODULEThere is only one interface module available for MINI diagnostic system, OBDII-IM5. Insert theinterface module into the base unit firmly if the socket in the vehicle is OBD-II, and connect theadapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for MINI © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH MINI

3. CONNECT TO THE VEHICLEPlug the available diagnostic socket into the diagnostic socket in the vehicles. Select the MINIfrom the screen of iSCAN-II. Press ENTER to start to diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. MINI iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered..ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter for thenew models. Connect to theOBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for MINI © 2008 Autoland Scientech. Page 2 MINI

START TO DIAGNOSESelect MINI by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.MINI   TRANSMISSION  1 ENGINE 1 ID CODES2 TRANSMISSION 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for MINI. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for MINI © 2008 Autoland Scientech. Page 3 MINI

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for MINI © 2008 Autoland Scientech. Page 4 MINI

iSCAN-II DocumentationMITSUBISHI® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for MITSUBISHI diagnostic system. Please note thatprior to the year 2000 most vehicles were equipped with 12-pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. For new models after 2006, the communication protocol of ECUs is CAN. Please use OBDII-IM5 first on new models, then try ASIAN-IM1 if the communication with some systems are failed.12-PIN Soc ket For the old models which equipped with 12-PIN round socket, located in the fuse box under the steering wheel on the driver side. Some models may be equipped with OBD-II and 12-PIN connectors together. Try both connectors by using ASIAN-IM1.2. SELECT THE INTERFACE MODULEThere are two interface modules available for MITSUBISHI diagnostic system, OBDII-IM5 andASIAN-IM1. Insert the interface module into the base unit firmly. Select the adapter thatcorresponds to the socket, ex. OBDII-AC-16P.iSCAN-II for MITSUBISHI © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH MITSUBISHI

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select theMITSUBISHI from the screen of iSCAN-II. Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. If themodel is equipped with 12-PIN diagnostic socket, plug the cigarette lighter power cable, BU-EC-1.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 ACURA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 MITSUBISHI iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for MITSUBISHI © 2008 Autoland Scientech. Page 2 MITSUBISHI

ADAPTERS AND INTERFACE MODULEThere are two interface modules available for the diagnostic system, OBDII-IM5 and ASIAN-IM1.OBDII-IM5 ASIAN-IM1OBD-II Full Specification Multiplexer ASIAN Interface Module for TOYOTA / NISSAN /MITSUBISHI / HYUNDAI / KIAOBDII-AC-16P MIT-AC-12P BU-EC-1The most common adapter forthe new models. Connect to theOBDII-IM5 or ASIAN-IM1 withAC-EC1.The adapter for the oldmodels. Connect to theASIAN-IM1 with AC-EC1.Ashtray lighter power cable, thepower source for 12-PINdiagnostic socket models.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for MITSUBISHI © 2008 Autoland Scientech. Page 3 MITSUBISHI

START TO DIAGNOSESelect MITSUBISHI by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.MITSUBISHI   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATIONThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for MITSUBISHI. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for MITSUBISHI © 2008 Autoland Scientech. Page 4 MITSUBISHI MITSUBISHI

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.For models manufactured at 2006, which interface module should I insert?Try OBDII-IM5 first, then ASIAN-IM1. OBDII-IM5 is applicable to CAN-protocol, and ASIAN-IM1 is to MITSUBISHI specific protocol. To connect with CAN-protocol models, ASIAN-IM1 maysend traditional signals to interrupt the inter-connection of the CAN-bus and cause fault codes.Please use OBDII-IM5 with iSCAN-II MITSUBISHI diagnostic software to clear the fault code.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for MITSUBISHI © 2008 Autoland Scientech. Page 5 MITSUBISHI

iSCAN-II DocumentationOPEL® VAUXHALL®DIAGNOSTIC SYSTEMGETTING STARTEDiSCAN-II OPEL Diagnostic Software has many sub-versions for different areas.1. FIND THE DIAGNOSTIC SOCKETThere are 3 kinds of diagnostic sockets for OPEL / VAUXHALL diagnostic system. Please notethat prior to the year 1998 most vehicles were equipped with 12-pin socket or 10-pin socket.OBD- II Socket Most OBD-II diagnostic socket is located under the steering wheel on driver side. 12-PIN SocketFor the old models equipped with 12-PIN socket, the connector of the socket needs the power source from Ashtray lighter power cable.10-PIN SocketThe 10-Pin socket is located either in the engine compartment beside the driver side or in the absorber strut tower on passenger side.2. SELECT THE INTERFACE MODULEThere is only one interface module available for OPEL diagnostic system, OBDII-IM5. Insert theinterface module into the base unit firmly. Select the adapter that corresponds to the socket, ex.OBDII-AC-16P.ISCAN-II for OPEL © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH OPEL / VAUXHALL

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select the OPELfrom the screen of iSCAN-II . Press ENTER to start to diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. OPEL iSCAN-II (V1.00)6. OPEL UK iSCAN-II (V2.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ISCAN-II for OPEL © 2008 Autoland Scientech. Page 2 OPEL / VAUXHALL

ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5OBD-II Full Specification MultiplexerOBDII-AC-16P GM-AC-12P OPL-AC-10PThe most common adapter forthe new models. Connect to theOBDII-IM5 with AC-EC1.The adapter for the old models. The adapter for the old models.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.ISCAN-II for OPEL © 2008 Autoland Scientech. Page 3 OPEL / VAUXHALL

START TO DIAGNOSESelect OPEL by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.OPEL   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for OPEL / VAUXHALL. Please refer tothe software specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.ISCAN-II for OPEL © 2008 Autoland Scientech. Page 4 OPEL / VAUXHALL OPEL / VAUXHALL

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.ISCAN-II for OPEL © 2008 Autoland Scientech. Page 5 OPEL / VAUXHALL

iSCAN-II DocumentationPERODUA® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Socket The OBD-II diagnostic socket is located under the steering wheel on driver side. OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for PERODUA diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly. Select the adapter that corresponds to thesocket, ex. OBDII-AC-16P.iSCAN-II for PERODUA © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH PERODUA

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select thePERODUA from the screen of iSCAN-II . Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN>1 <KOREA>2 <JAPAN>3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~) MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. PERODUA iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full Specification Multiplexer The most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for PERODUA © 2008 Autoland Scientech. Page 2 PERODUA

START TO DIAGNOSESelect PERODUA by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.PERODUA   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for PERODUA. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for PERODUA © 2008 Autoland Scientech. Page 3 PERODUA

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for PERODUA © 2008 Autoland Scientech. Page 4 PERODUA

iSCAN-II DocumentationPEUGEOT® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover. Some of them can be found behind the Ashtray box or the relay box.OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for PEUGEOT diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly if the socket in the vehicle is OBD-II, andconnect the adapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for PEUGEOT © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH PEUGEOT

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select thePEUGEOT from the screen of iSCAN-II. Press ENTER to start to diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>FRENCH PKG1 <BMW GT2>2 <FRENCH PKG>1 RENAULT iSCAN-II (V1.00)3 MB iSCAN-II (V1.00)4. FIAT2 CITROEN iSCAN-II (V1.00)3 PEUGEOT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00) iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter forthe new models. Connect to theOBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for PEUGEOT © 2008 Autoland Scientech. Page 2 PEUGEOT

START TO DIAGNOSESelect PEUGEOT by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.PEUGEOT   ENGINE  1 106 1 ID CODES2 206 2 READ FAULT CODE3 2074 3065 3073 CLEAR FAULT CODE4 DATA STREAM6 4067 4078 607The figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for PEUGEOT. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for PEUGEOT © 2008 Autoland Scientech. Page 3 PEUGEOT

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for PEUGEOT © 2008 Autoland Scientech. Page 4 PEUGEOT

iSCAN-II DocumentationPORSCHE® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic adapters for PORSCHE diagnostic system. Please note thatprior to the year 2000 most vehicles were equipped with the PORSCHE specified socket underthe dash board.OBD- II Soc ket For the newer models, ex. Cayenne, 996, Cayman...etc, the diagnostic socket can be found under the dashboard on driver side and covered by a plastic cover. It is very close to side kicker and near the door.OBD-II socket19-PIN PORSCHE Specified Soc ket 19-Pin diagnostic socket can be found under the dashboard on driver side or under the glove compartment on passenger's.2. SELECT THE INTERFACE MODULEThere is only one interface module available for PORSCHE diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly if the socket in the vehicle is OBD-II, andconnect the adapter that corresponds to the socket, OBDII-AC-16P. iSCAN-II for PORSCHE © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH PORSCHE

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select thePORSCHE from the screen of iSCAN-II. Press ENTER to start to diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. PROSCHE iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16P PCSH-AC-19PInsert this interface module forthe models equipped with onlyOBD-II socket.The most common adapter forthe new models. Connect to theOBDII-IM5 with AC-EC1.The adapter for the oldmodels. Connect directly toiSCAN-II using BU-EC. There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for PORSCHE © 2008 Autoland Scientech. Page 2 PORSCHE PORSCHE

START TO DIAGNOSESelect PORSCHE by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.PORSCHE   DME 7.2  1 Cayenne 1 ID CODES2 Cayman 2 READ FAULT CODE3 9974 9875 9963 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATION6 986 6 ADAPTATION7 9688 944The figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for PORSCHE. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for PORSCHE © 2008 Autoland Scientech. Page 3 PORSCHE

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything in LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for PORSCHE © 2008 Autoland Scientech. Page 4 PORSCHE

iSCAN-II DocumentationPROTON® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for PROTON diagnostic system. OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. Please useASIAN-IM1.12-PIN Soc ket For the old models equipped with 12-PIN round socket, located in the fuse box under the steering wheel on driver side. Some models may be equipped with OBD-II and 12-PIN connectors together. Try both connectors by using ASIAN-IM1.2. SELECT THE INTERFACE MODULEThere is only one interface module available for PROTON diagnostic system, ASIAN-IM1. Insertthe interface module into the base unit firmly. Select the adapter that corresponds to the socket,ex. OBDII-AC-16P.iSCAN-II for PROTON © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH PROTON

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select thePROTON from the screen of iSCAN-II. Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. If themodel is equipped with 12-PIN diagnostic socket, plug the cigarette lighter power cable, BU-EC-1.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN>1 <KOREA>2 <JAPAN>3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~) MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. PROTON iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.iSCAN-II for PROTON © 2008 Autoland Scientech. Page 2 PROTON

ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, ASIAN-IM1.ASIAN-IM1ASIAN Interface Module for TOYOTA /NISSAN / MITSUBISHI / HYUNDAI /KIAOBDII-AC-16P MIT-AC-12P BU-EC-1The most common adapter forthe new models. Connect to theASIAN-IM1 with AC-EC1.The adapter for the oldmodels. Connect to theASIAN-IM1 with AC-EC1.Ashtray lighter power cable, thepower source for 12-PINdiagnostic socket models.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for PROTON © 2008 Autoland Scientech. Page 3 PROTON

START TO DIAGNOSESelect PROTON by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.PROTON   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATIONThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for PROTON. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for PROTON © 2008 Autoland Scientech. Page 4 PROTON

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for PROTON © 2008 Autoland Scientech. Page 5 PROTON

iSCAN-II DocumentationRENAULT® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic sockets can be found under the dashboard on driver side and are covered by a plastic cover. Some of them can be found behind the Ashtray or the relay box.OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for RENAULT diagnostic system, OBDII-IM5.Insert the interface module into the base unit firmly if the socket in the vehicle is OBD-II, andconnect the adapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for RENAULT © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH RENAULT

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theRENAULT from the screen of iSCAN-II . Press ENTER to start to diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>FRENCH PKG1 <BMW GT2>2 <FRENCH PKG>1 RENAULT iSCAN-II (V1.00)3 MB iSCAN-II (V1.00)4. FIAT2 CITROEN iSCAN-II (V1.00)3 PEUGEOT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00) iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter for thenew models. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for RENAULT © 2008 Autoland Scientech. Page 2 RENAULT

START TO DIAGNOSESelect RENAULT by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.RENAULT   ENGINE  1 AVANTIME 1 ID CODES2 CLIO II 2 READ FAULT CODE3 ESPACE4 KANGOO5 LAGUNA3 CLEAR FAULT CODE4 DATA STREAM6 MEGANE7 THALIA8 TRAFICThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for RENAULT. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for RENAULT © 2008 Autoland Scientech. Page 3 RENAULT

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for RENAULT © 2008 Autoland Scientech. Page 4 RENAULT

iSCAN-II DocumentationSAAB® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover.OBD-II socketOther Soc ket iSCAN-II SAAB Diagnostic Software does not support the vehicles which are equipped with the other sockets. 2. SELECT THE INTERFACE MODULEThere is only one interface module available for SAAB diagnostic system, OBDII-IM5. Insert theinterface module into the base unit firmly if the socket in the vehicle is OBD-II, and connect theadapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for SAAB © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH SAAB

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diangostic socket in the vehicle. Select the SAABfrom the screen of iSCAN-II . Press ENTER to start to diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. SAAB iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16PInsert this interface module forthe models equipped with onlyOBD-II socket.The most common adapter for the newmodels. Connect to the OBDII-IM5 withAC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for SAAB © 2008 Autoland Scientech. Page 2 SAAB

START TO DIAGNOSESelect SAAB by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.SAAB   TRANSMISSION  1 ENGINE 1 ID CODES2 TRANSMISSION 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for SAAB. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for SAAB © 2008 Autoland Scientech. Page 3 SAAB

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connect to the system but show 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause. Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for SAAB © 2008 Autoland Scientech. Page 4 SAAB

iSCAN-II DocumentationSMART® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Soc ket Most OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover.OBD-II socketOther Soc ket iSCAN-II SMART Diagnostic Software does not support the vehicles which are equipped with the other sockets. 2. SELECT THE INTERFACE MODULEThere is only one interface module available for SMART diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly if the socket in the vehicle is OBD-II, and connectthe adapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for SMART © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH SMART

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select theSMART from the screen of iSCAN-II . Press ENTER to start to diagnostic function. If the modelis not listed on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. SMART iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16PInsert this interface module for themodels equipped with only OBD-IIsocket.The most common adapter forthe new models. Connect to theOBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for SMART © 2008 Autoland Scientech. Page 2 SMART

START TO DIAGNOSESelect SMART by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions. SMART   TRANSMISSION  1 ENGINE 1 ID CODES2 TRANSMISSION 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for SMART. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for SMART © 2008 Autoland Scientech. Page 3 SMART SMART

TROUBLE SHOTTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for SMART © 2008 Autoland Scientech. Page 4 SMART

iSCAN-II DocumentationSUBARU® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETOBD- II Socket The OBD-II diagnostic socket is located under the steering wheel on driver side.OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for SUBARU diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly. Select the adapter that corresponds to the socket,ex. OBDII-AC-16P.iSCAN-II for SUBARU © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH SUBARU

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select theSUBARU from the screen of iSCAN-II . Press ENTER to start the diagnostic function. If themodel is not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 ACURA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 SUBARU iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16POBD-II Full Specification Multiplexer The most common adapter for the newmodels. Connect to the OBDII-IM5 with AC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for SUBARU © 2008 Autoland Scientech. Page 2 SUBARU

START TO DIAGNOSESelect SUBARU by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.SUBARU   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for SUBARU. Please refer to thesoftware specification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for SUBARU © 2008 Autoland Scientech. Page 3 SUBARU

TROUBLE SHOOTINGiSCAN- II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for SUBARU © 2008 Autoland Scientech. Page 4 SUBARU

iSCAN-II DocumentationSUZUKI® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for SUZUKI diagnostic system. Please note that priorto the year 1998, most vehicles are equipped with 12-Pin socket.OBD- II Socket Most OBD-II diagnostic sockets are located under the steering wheel on driver side. OBD-II socket12-PIN Soc ket For the old models equipped with 12-PIN socket, please refer to the sticker direction under thedashboard on driver side and near the steering column.2. SELECT THE INTERFACE MODULEThere is only one interface module available for SUZUKI diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly. Select the adapter that corresponds to the socket,ex. OBDII-AC-16P.iSCAN-II for SUZUKI © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH SUZUKI

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicles. Select theSUZUKI from the screen of iSCAN-II . Press ENTER to start the diagnostic function. If the modelis not listed on the screen, try to press RIGHT / LEFT buttons to turn the page. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<ASIAN><JAPAN>1 <KOREA>2 <JAPAN>1 DAIHATSU NON-CAN iSCAN-II (V1.00)3 CHRYSLER iSCAN-II (V1.00)4 FORD OEM(OBDII 95~)2 DAIHATSU CAN iSCAN-II (V1.00)3 HONDA MAZDA OEM(OBDII 01~) iSCAN-II (V1.00)5. GM US iSCAN-II (V1.00)4 ACURA iSCAN-II (V1.00) iSCAN-II (V1.00) 5 SUZUKI iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5.OBDII-IM5 OBDII-AC-16P GM-AC-12POBD-II Full SpecificationMultiplexerThe most common adapter for thenew models. Connect to theOBDII-IM5 with AC-EC1.The adapter for the old models.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for SUZUKI © 2008 Autoland Scientech. Page 2 SUZUKI

START TO DIAGNOSESelect SUZUKI by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions.SUZUKI   ENGINE  1 ENGINE 1 ID CODES2 A/T 2 READ FAULT CODE3 ABS4 SRS5 EPS3 CLEAR FAULT CODE4 DATA STREAMThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for SUZUKI. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for SUZUKI © 2008 Autoland Scientech. Page 3 SUZUKI SUZUKI

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there's no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause. Successfully connects to the system but shows 'LINK FAILURE' on the title? Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix the problems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserve the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for SUZUKI © 2008 Autoland Scientech. Page 4 SUZUKI

iSCAN-II DocumentationVASS® DIAGNOSTIC SYSTEMGETTING STARTEDVASS means Volkswagen, Audi, Seat, Skoda (the Volkswagen groups).1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for VASS diagnostic system. Please note that prior tothe year 1995, most vehicles were equipped with black/white socket under the engine hood.OBD- II Soc ket For the newer models, OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover. For old models equipped with OBD-II socket, the location may be different.OBD-II socketBLACK / WHITE Soc ket BLACK / WHITE diagnostic socket can be found in the engine compartment beside the driver side. Or near the absorber strut tower on the either side of driver and passenger.2. SELECT THE INTERFACE MODULEThere is only one interface module available for VASS diagnostic system, OBDII-IM5. Insert theinterface module into the base unit firmly if the socket in the vehicle is OBD-II, and connect theadapter that corresponds to the socket, OBDII-AC-16P.iSCAN-II for VASS © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH VASS

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket in the vehicle. Select the VASSfrom the screen of iSCAN-II . Press ENTER to start to diagnostic function. If the model is notlisted on the screen, try to press RIGHT / LEFT buttons to turn the page.MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II(V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. VASS iSCAN-II (V1.00)6. LANDROVER iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16P VASS-CInsert this interface module forthe models equipped with onlyOBD-II socket.The most common adapter forthe new models. Connect tothe OBDII-IM5 with AC-EC1.The adapter for the old models.Connect to the OBDII-IM5 withAC-EC1.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for VASS © 2008 Autoland Scientech. Page 2 VASS

START TO DIAGNOSESelect VASS by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions. AUDI   Engine  1 Power Train 1 ID CODES2 Chassis 2 READ FAULT CODE3 Body4 Information and Communication3 CLEAR FAULT CODE4 DATA STREAM5 BASIC SETTING5 Air condition 6 ADAPTATIONThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered.Autoland Scientech will keep updating the diagnostic software for VASS. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for VASS © 2008 Autoland Scientech. Page 3 VASS

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owners.iSCAN-II for VASS © 2008 Autoland Scientech. Page 4 VASS

iSCAN-II DocumentationVOLVO® DIAGNOSTIC SYSTEMGETTING STARTED1. FIND THE DIAGNOSTIC SOCKETThere are two kinds of diagnostic sockets for VOLVO diagnostic system. Please note that priorto the year 1997 most vehicles were equipped with AB-diagnostic socket under the enginehood.A/B Diagnostic SocketFor the models 700/800/900 Series, between year 1989 to 1996, A/B diagnostic socket can be found in the engine compartment, behind the driver side or passenger side absorber strut tower.OBD- II Socket For the newer models, ex. S70 / S80 / XC90...etc, OBD-II diagnostic socket can be found under the dashboard on driver side and are covered by a plastic cover. It is very close to side kicker and near the door.OBD-II socket2. SELECT THE INTERFACE MODULEThere is only one interface module available for VOLVO diagnostic system, OBDII-IM5. Insertthe interface module into the base unit firmly if the socket in the vehicle is OBD-II, and connectthe adapter that corresponds to the socket, OBDII-AC-16P. Do NOT insert any interfacemodule for old models equipped with AB-diagnostic socket.iSCAN-II for VOLVO © 2008 Autoland Scientech. Page 1AUTLAND® SCIENTECH VOLVO

3. CONNECT TO THE VEHICLEPlug the available diagnostic adapter into the diagnostic socket at the vehicles. Select theVOLVO from the screen in iSCAN-II. Press ENTER to start to diagnose. If the models are notlisted in the screen, try to press RIGHT / LEFT buttons to find more models. MAIN MENUVehicle Diagnostic 1 Vehicle Diagnostic 1 <ASIAN> 2 IMS2(Interface Module 2 <EUROPEAN> Simulation System) 3 Component Test System10 OBDII Standard Compliant iSCAN-II (V1.00)20 SETUP<EUROPEAN>1 <BMW GT2>2 <FRENCH PKG>3 MB iSCAN-II (V1.00)4. FIAT iSCAN-II (V1.00)5. JAGUAR iSCAN-II (V1.00)6. VOLVO iSCAN-II (V1.00)The figure is for reference only. Autoland Scientech updates the software very often. Thescreen shown may not be the same as the newest software delivered.ADAPTERS AND INTERFACE MODULEThere is only one interface module available for the diagnostic system, OBDII-IM5. OBDII-IM5 OBDII-AC-16P D51-C-MBLVInsert this interface module forthe models equipped with onlyOBD-II socket.The most common adapter forthe new models. Connect tothe OBDII-IM5 with AC-EC1.MB 8/16-pin and Volvo A/Bconnectors. The adapter for theold models. Connect directly toiSCAN-II using BU-EC.There are some adapters available. Refer to the “Diagnostic Cable Connection Quick Manual” for moredetailed connection / wiring information.iSCAN-II for VOLVO © 2008 Autoland Scientech. Page 2 VOLVO

START TO DIAGNOSESelect VOLVO by pressing the ENTER button. Turn ignition ON or make engine running at idle.WARNING! Ignition ON without engine running may have a flat battery.Select the system from the screen. There may be many systems on the vehicle, try to press RIGHTbutton to turn the page. If the ECU response is successful, the screen will show all the availablefunctions. VOLVO   XC90  1 Models up to 1997 1 ID CODES2 Models from 1997 2 READ FAULT CODE3 CLEAR FAULT CODE4 DATA STREAM5 ACTIVATION6 ADAPTATIONThe figure is for reference only. Autoland Scientech updates the software very often. The screenshown may not be the same as the newest software delivered. We may simplify the steps of theprocedure.Autoland Scientech will keep updating the diagnostic software for VOLVO. Please refer to the softwarespecification.Visit our website, http://www.autolandscientech.com , and apply for membership. You will get E-paperevery month and find more diagnostic technical information.iSCAN-II for VOLVO © 2008 Autoland Scientech. Page 3 VOLVO VOLVO

TROUBLE SHOOTINGiSCAN-II never shows anything on LCD screen and there’s no back-light?1. Please check the cable and the connector again.2. The voltage of the battery should be higher than 10V. 3. Check the power from OBD-II connector. PIN-16 is power, PIN-4 or PIN-5 is ground.4. Check fuses in BU-EC (25-Pin Base Unit Extension Cable).iSCAN-II never shows anything on LCD screen and the back-light is ON?1. Check the diagnostic software using iSCAN-II/PSModule3 File Manager from PC. Thesoftware for iSCAN-II may be missing or broken.2. Adjust the brightness dial for the LCD panel. The brightness may be too dark.Can't find the system on the screen?1. Press Right button for more systems. There are too many systems which can't be shownon the same page.2. The diagnostic software does not have this system. Please refer to the specification. Weapologize for the inconvenience.The green or yellow LED flashed on for a while, then showed 'CONNECTION FAILED'on the LCD screen?1. Make sure the ignition is ON or make the engine running at idle.2. Ignition OFF for a while, then Ignition ON and try again.3. Check the cable and the adapter. Unplug all cables and adapters and plug-in again.4. Make sure the vehicle equips with the correct system. For example, the manualtransmission will not have A/T transmission ECU.5. The vehicle will NOT equip with all the systems listed on the software. Some specialsystems are only available on the luxury models.6. The ECU is malfunction or the diagnostic line from the ECU is open or short to the ground orpower.7. Battery voltage is too low.Successfully connected to the system but shows 'VERSION UNKNOWN' on the LCDscreen?Due to the prompt development of the Motor manufactures, the diagnostic software might notbe able to communicate with all ECU versions. Download the newest software from the memberarea of Autoland Scientech website and try again. (http://www.autolandscientech.com)If the same situation occurs, please report the information of ID pages to our local distributors.We will keep updating the diagnostic software for new ECUs. Please excuse any inconveniencethis may cause.Successfully connects to the system but shows 'LINK FAILURE' on the title?Some ECUs are not as stable as our research department expected. Please report the information of ID pages to our local distributors. Our R/D department will do our best to fix theproblems as soon as possible. Please excuse any inconvenience this may cause.The ECU successfully responds but the data stream seems wrong?Try to select OTHER YEARS. VOLVO changes the protocols EVERY year and the manufactureyear may not be the same as the list in the license plate.For A/B diagnostic sockets: The ECU failed to respond, received fault codes?For old cars, the ground pin of an A/B diagnostic socket is not so stable. Try to make the groundpin stable by connect a wire to the battery or polish the ground in the diagnostic socket. iSCAN-II for VOLVO © 2008 Autoland Scientech. Page 4 VOLVO

Fail to reset the service light for S70 / V70 ?The service light can not be reset directly. Modify the service time / distance, then reset theservice again.Document Version 1.00 for iSCAN-II, © 2008 Autoland ScientechThe information contained herein is the exclusive property of Autoland Scientech® and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Autoland Scientech®. Autoland Scientech® reserves the right to make any changewithout notice. The trademarks mentioned belong to the owner.iSCAN-II for VOLVO © 2008 Autoland Scientech. Page 5 VOLVO

USER’S NOTICE ACKNOWLEDGMENT Products referred to in this manual are mentioned for identification purposes only. Product names appearing in this manual or on the Scanner’s screen may or may not be registered trademarks or copyrights of their respective companies. ACURA is a registered trademark of Honda Motor Company, Limited. ALFA ROMEO is a registered trademark of Fiat S.p.A. AUDI is a registered trademark of AUDI AG. BENTLEY is a registered trademark of Bentley Motors Limited, Volkswagen AG. BMW is a registered trademark of Bayerische Motoren Werke AG. BUICK is a registered trademark of General Motors Corporation. CADILLAC is a registered trademark of General Motors Corporation. CHERY is a registered trademark of Chery Automobile Co., Ltd.. CHEVROLET is a registered trademark of General Motors Corporation. CHRYSLER is a registered trademark of Chrysler LLC. CITROЁN is a registered trademark of PSA Peugeot Citroën. DAEWOO is a registered trademark of GM Daewoo Auto & Technology.DAIHATSU is a registered trademark of GM Daihatsu Motor Company.DODGE is a registered trademark of Chrysler LLC. FIAT is a registered trademark of Fiat S.p.A. FORD is a registered trademark of Ford Motor Company. GM is a registered trademark of General Motors Corporation. GMC is a registered trademark of General Motors Corporation. GREATWALL is a registered trademark of Great Wall Motor Company. HOLDEN is a registered trademark of GM Holden Ltd. HONDA is a registered trademark of Honda Motor Company, Limited. HYUNDAI is a registered trademark of Hyundai Motor Company.INFINITI is a registered trademark of Nissan Motor Company.ISUZU is a registered trademark of Isuzu Motors Ltd. JAGUAR is a registered trademark of Jaguar Cars Limited. JEEP is a registered trademark of Chrysler LLC. KIA is a registered trademark of KIA Motors, Hyundai Kia Automotive Group.LANDROVER is a registered trademark of Premier Automotive Group, Ford Motor Company, and Tata Motors. LEXUS is a registered trademark of Toyota Motor Corporation. MAYBACH is a registered trademark of Maybach-Motorenbau GmbH, Daimler AG. MAZDA is a registered trademark of MAZDA Motor Corporation. MERCEDES BENZ is a registered trademark of Daimler AG. MINI is a registered trademark of Bayerische Motoren Werke AG. MITSUBISHI is a registered trademark of Mitsubishi Motors Corporation. NISSAN is a registered trademark of Nissan Motor Company.OLDSMOBILE is a registered trademark of General Motors Corporation. OPEL is a registered trademark of Adam Opel GmbH, General motors Corporation. PONTIAC is a registered trademark of General Motors Corporation. PERODUA is a registered trademark of Perodua Automotive. PEUGEOT is a registered trademark of PSA Peugeot Citroën. PORSCHE is a registered trademark of Porsche AG. PROTON is a registered trademark of Proton Holdings Berhad. RENAULT is a registered trademark of Renault S.A. SAAB is a registered trademark of Saab Automobile AB. SATURN is a registered trademark of Saturn Corporation, General Motors Corporation. SCION is a registered trademark of Toyota Motor Corporation. SEAT is a registered trademark of SEAT S.A., Volkswagen Group. SKODA is a registered trademark of Skoda Auto, Volkswagen Group.SMART is a registered trademark of Smart GmbH, Daimler AG.SSANGYONG is a registered trademark of SsangYong Motor Company. SUBARU is a registered trademark of Fuji Heavy Industries Co., Ltd. SUZUKI is a registered trademark of SUZUKI Motor Corporation. TOYOTA is a registered trademark of Toyota Motor Corporation. VOLKSWAGEN is a registered trademark of Volkswagen AG. VOLVO is a registered trademark of the Volvo Car Coporation, Ford Motor Company.SII is a registered trademark of Seiko Instruments Inc. Microsoft © and Windows © are registered trademarks of Microsoft Corporation.

COPYRIGHT This instruction manual and PC Scanner CD-ROM are published by AUTOLAND SCIENTECH® and are protected by copyright and other intellectual property rights in existence at all times and in all territories throughout the world. Permission is hereby granted to print a hard copy ONLY for the sole purpose of using this as an information resource for operating products manufactured by AUTOLAND SCIENTECH®. No part of this instruction manual or the PC Scanner software may be reproduced republished or transmitted, in any form or by any means, whether electronic, mechanical, copied, or otherwise, unless a prior consent from AUTOLAND SCIENTECH® has been obtained. DISCLAIMER AND LIABILITY The information and illustrations contained in this manual are based on the latest information available at the time of publication. AUTOLAND SCIENTECH® reserves the right to make changes at any time without notice. This instruction manual tells users how to use the Scanner to perform diagnostic tests and find possible locations of vehicle problems. It does NOT tell users how to correct the problems. Consult the manufacturer’s vehicle service manual or other publication for repair instructions. To make full use of the Scanner’s capabilities, the user should be knowledgeable and well-trained in each of the vehicle computer control systems described in this manual. Service data that appear to be non-functional on some vehicles may be due to changes in vehicle manufacturing design. In addition, AUTOLAND SCIENTECH® shall not accept responsibility for any incidental or consequential damages under any circumstances, in connection with using this instructional manual or PC-Scanner software, nor shall AUTOLAND SCIENTECH® be liable for any errors contained in this instruction manual. iSCAN-II Manual, Version 1.0 May 2008 © Copyright 1998 by AUTOLAND SCIENTECH® Co., Ltd. All rights reserved

OPERATIONAL GUIDELINES This section explains crucial operational guidelines that must be observed when using diagnostic tools and memory cartridges produced by AUTOLAND SCIENTECH®. It is important to read these guidelines before operating on a vehicle in order to avoid any personal injury or damage to the vehicle or diagnostic equipment. TO AVOLD VOLTAGE SPIKESTo avoid the possible voltage spikes and to protect the vehicle and diagnostic tools from resultant damage, please do not connect or disconnect the diagnostic tool while the ignition key is ON or while the engine is running.TURN THE DIAGNOSTIC TOOL OFF WHILE INSERTING/REMOVING MEMORY CARTRIDGEPlease do not insert or remove memory cartridges while the diagnostic tool’s power is ON. To change a memory cartridge, please follow the steps below: a. Turn the ignition OFF. b. Disconnect the diagnostic tool’s power supply source. c. Change the memory cartridge. d. Reconnect the diagnostic tool’s power supply source. e. Turn the ignition ON. PUT THE PARKING BRAKE ONIn order to avoid personal injury or damage to the vehicle that might result from incorrect operation, please always apply the parking brake and block the wheels when operating the diagnostic tool. DANGER! DRIVING TESTPlease DO NOT leave any moving parts below the driving seat. Any moving parts may block the brake pads. The car will lost control and the drivers will injure if the brake fail. DO NOT drive too quick if the diagnostic connecter is below the engine hood. Too heavy the wind will open the engine hood because the hood is not proper locked.

Federal Communications Commission (FCC) Statement 15.21You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2025 UserManual.wiki | Privacy Policy

Contact Us
DMCA