Abocom Systems WG2100 802.11b/g MII Module User Manual WG2100 manual OK

Abocom Systems Inc 802.11b/g MII Module WG2100 manual OK

User manual

802.11 b/g MII Module User’s Manual
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. CAUTION 1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 3. For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible.
Table of Contents INTRODUCTION...................................................................................................1 WIRELESS NETWORK OPTIONS ...............................................................................1 The Peer-to-Peer Network .........................................................................1 The Access Point Network ........................................................................2 INSTALLATION ....................................................................................................3 HARDWARE INSTALLATION.....................................................................................3 SOFTWARE INSTALLATION......................................................................................3 Device Installation Verification.................................................................5 CONFIGURATION ................................................................................................6 ACCESSING THE CONFIGURATION UTILITY..............................................................7 EASY CONFIG.........................................................................................................7 MAIN TAB............................................................................................................11 PROFILE TAB........................................................................................................13 ADVANCED TAB ...................................................................................................19 INFO TAB .............................................................................................................20 ABOUT TAB..........................................................................................................21 UNINSTALLATION.............................................................................................22
- 1 - INTRODUCTION The 802.11b/g MII Module is a device that allows you connect your computer to a wireless local area network (LAN). A wireless LAN allows your system to use wireless Radio Frequency (RF) technology to transmit and receive data without physically attaching to the network. The wireless protocols that come with this product ensure data security and isolation from interference generated by other radio frequencies. This card also allows you to take full advantage of your computer’s mobility with access to real-time information and online services anytime and anywhere. In addition, this device eliminates the bother of pulling cable through walls and under furniture. It even allows you to place your system in locations where cabling is impossible. Modifying and augmenting networks has never been so easy. Wireless Network Options The Peer-to-Peer Network This network installation lets you set a small wireless workgroup easily and quickly. Equipped with wireless PC Cards or wireless Mini PCI, you can share files and printers between each PC and laptop.
- 2 - You can also use one computer as an Internet Server to connect to a wired global network and share files and information with other computers via a wireless LAN. The Access Point Network The network installation allows you to share files, printers, and Internet access much more conveniently. With Wireless LAN Cards, you can connect wireless LAN to a wired global network via an Access Point.
- 3 - INSTALLATION Hardware Installation 1. Make sure the computer is turned off. Remove the expansion slot cover from the computer. 2. Carefully slide the MII Module into the Mini PCI slot. Push evenly and slowly and ensure it is properly seated. 3. After the device has been connected to your computer, turn on your computer. Windows will detect the new hardware and then automatically copy all of the files needed for networking. Software Installation 1. Exit all Windows programs. Insert the CD-ROM into the CD-ROM drive of your computer. If the CD-ROM is not launched automatically, go to your CD-ROM drive (e.g. drive D) and double-click on Setup.exe. 2. The main screen of the CD-ROM opens. Click Install Driver & Utility to start the installation.
- 4 - 3. When the Welcome screen appears, click Next to continue. 4. Click Finish to complete the software installation.
- 5 - Device Installation Verification To verify that the device has been properly installed in your computer and is enabled, go to Start  Settings  Control Panel  System ( Hardware)  Device Manager. Expand the Network adapters item. If the 802.11b/g MII Module is listed, it means that your device is properly installed and enabled.
- 6 - CONFIGURATION After successful installation of the module’s driver, the utility icon will display in the task bar. You will be able to access the Configuration Utility through the Network Status icon. If the icon doesn’t appear automatically, go to Start  Programs  802.11 b/g MII Module Utility  802.11 b/g MII Module Utility, it will appear in the task bar.
- 7 - Accessing the Configuration Utility All settings are categorized into 5 Tabs: Main Tab Profile Manager Tab Advanced Tab Info Tab About Tab Easy Config 1. In the Main tab, click Easy Config on the right down corner to start a quick configuration.
- 8 - 2. Select the wireless connection type- Infrastructure. Then click Next to continue. 3. Select a wireless station on the list, and click Next to configure its settings.
- 9 - The following screen will appear for you to configure, for detailed configuration, please refer to Profile tab in the later selection. 4. Configure the network TCP/IP, you may select DHCP to obtain an IP address automatically or select Manual to set an IP address. Click Next to continue.
- 10 - 5. Select DNS Auto to obtain DNS automatically or select Manual to set the primary and secondary DNS. Click Finish to complete the Easy Config procedure.
- 11 - Main Tab The main tab enables you to scan for available networks, select a network to which to connect, modify the settings for the current connection. Status Shows the current connection status. Speed Shows the connection speed. Type Shows the wireless connection type. Authentication Shows the authentication type. Encryption Shows the encryption type. SSID The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network. Signal Strength The signal strength from the network Access Point or station. Link Quality Shows the link quality percentage. Total Throughput Shows the total throughput percentage.
- 12 - Throughput TX The actual instantaneous transmitting rates. Throughput RX The actual instantaneous receiving rates. Network Address MAC Address The MAC address of this wireless adapter. IP Address The IP address of this wireless adapter. Subnet Mask The subnet mask of this wireless adapter. Gateway The default gateway address of the adapter. □ Show Tray icon Place a check in the check box to show the utility icon in the tray. □ Radio Off Place a check in the check box to disable the radio function. □ Windows Zero Config External Configuration Checkbox (Windows XP only): A checkbox that enables you to disable the WLAN Station Configuration Utility and indicates that the station driver is to be configured with Windows XP痴 built-in Zero Configuration Utility (ZCU). On Windows XP systems, the ZCU service is automatically stopped when the WLAN utility is installed. The ZCU is started when you check the Configure using Windows Zero Configuration checkbox. The checkbox is only displayed on Windows XP systems.
- 13 - Profile Tab The Profile tab enables you to connect, rescan, configuration, add, remove and edit the profiles that the station uses to connect to WLAN networks. Connect Select a wireless device that you want to connect with and click Connect button to make a connection. The wireless device you have connected will be added into the Available Profile(s) field below. Rescan Click Rescan button to refresh the wireless device list. Configure Click Configure to set up the detailed configuration. Add Click Add to add a wireless device into the Available Profile(s) field below. Remove Select a wireless device that listed in the Available Profile(s) field and then click Remove to delete it. Edit Select a wireless device in the Available Profile(s) field and then click Edit to change its configuration.
- 14 - Wireless Network Properties The Wireless Network Properties screen will appear if you just click Connect, Configure or Add buttons. Profile Name You may enter the preferred profile name in this column. Network Name (SSID) The SSID for the current profile. Wireless Network Security Network Authentication The authentication type defines configuration options for the sharing of wireless networks to verify identity and access privileges of roaming wireless network cards. Select the Network Authentication from the pull-down list. Open System: If the Access Point is using "Open System" authentication, then the wireless adapter will need to be set to the same authentication type. Shared Key: Shared Key is when both the sender and the recipient share a secret key.  If WEP is selected from Data encryption pull-down menu, you can either input Encryption Key 1~4 or check the Generate Key box and enter WEP keys in the Generate WEP Key blank, then the system will generate keys automatically.
- 15 -  WPA-PSK/WPA2-PSK: In the Passphrase field, enter the key (8~63 characters, case sensitive.) that you are sharing with the network for the WLAN connection. By default, the key that you type is masked with asterisks (*). To view the key that you entered, uncheck the Mask Key box. If WPA-PSK/WPA2-PSK is selected from Data encryption pull-down menu, enter the Passphrase in the column to setup the wireless network security.
- 16 - Data encryption Select the data encryption from the pull-down menu, either TKIP or AES. WEP Key Format  ASCII (American Standard Code for Information Interchange), the standard for assigning numerical values to the set of letters in the Roman alphabet and typographic characters.  HEX (Hexadecimal): numbers from 0 to 9 and letters from A to F.  Generate Key: Check the Generate Key box and enter WEP keys in the Generate WEP Key blank, then the system will generate keys automatically.  Mask Key: Place a check in the check box to enable the Unmask Key function, this function is for concealing the WEP key. Key Length Select the key length from the pull-down menu, either 64 Bit or 128 Bit. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters or 5 ASCII characters. If you are using 128-bit WEP encryption, then the key 26 hexadecimal characters or 13 ASCII characters. Valid hexadecimal characters are “0” to “9” and 鄭” to 擢”. Default Key Index Select the default key index 1~4 from the pull-down menu. Passphrase Instead of manually entering WEP keys, you can enter a Passphrase, so that a WEP key is automatically generated. It is case-sensitive and should not be longer than 16 alphanumeric characters. This Passphrase must match the Passphrase of your wireless network. Encryption Key 1~4 To configure your WEP settings. WEP (Wired Equivalent Privacy) encryption can be used to ensure the security of your wireless network. Select one Keyand Key Size then
- 17 - fill in the appropriate value/phrase in Encryption field. Note: You must use the same Key and Encryption settings for the both sides of the wireless network to connect. KEY 1 ~ KEY 4：You can specify up to 4 different keys to decrypt wireless data. Select the Default key setting from the radio button. Encryption：This setting is the configuration key used in accessing the wireless network via WEP encryption. A key of 10 hexadecimal characters (0-9, A-F) is required if a 64-bit Key Length was selected. A key of 26 hexadecimal characters (0-9, A-F) is required if a 128-bit Key Length was selected. A key of 58 hexadecimal characters (0-9, A-F) is required if a 256-bit Key Length was selected. 802.1x configure EAP TYPE WPA 802.1x/ WPA2 802.1x: Require setting up a RADIUS sever for authentication, RADIUS server manager will assign the username and password. Select the EAP TYPE from the pull-down list. Including TLS, TTLS and PEAP.
- 18 - Username Type in the user name assigned to the certificate. Certificate Please query your network manager about the certificate, select the same certificate as the certification server. OK Click OK to save the configuration. Cancel Click Cancel to exit the configuration screen.
- 19 - Advanced Tab The Advanced tab displays the current status of the module. Threshold Fragment Threshold The mechanism of Fragmentation Threshold is used to improve the efficiency when high traffic flows along in the wireless network. If your 802.11b/g Wireless LAN Adapter often transmits large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2432. The default value is 2432. RTS Threshold RTS/CTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. If the “Hidden Node” problem is an issue, users have to specify the packet size. The RTS/CTS mechanism will be activated if the data size exceeds the value you set. The default
- 20 - value is 2432. This value should remain at its default setting of 2432. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Connection Wireless Mode: Select 802.11b or 802.11g/b from the pull-down menu. Preamble Mode: A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. Select from the pull-down menu to change the Preamble type into Auto, Long or Short. Apply Click to save current changes. Set Default Click to restore default settings. Info Tab The Info tab displays information maintained by the driver, such as the number of packet errors and the total number of bytes received or transmitted. The tab also displays information about the current connection, as well as network information about the station. The statistics are for the period starting when you last connected to a network. The statistics are refreshed at least twice a second.
- 21 - About Tab Click on the About tab to view basic version information about the OS Version, Utility Version, Driver Version, Firmware Version and EEPROM Version.
- 22 - UNINSTALLATION In case you need to uninstall the Utility and driver, please refer to below steps. (As you uninstall the utility, the driver will be uninstalled as well.) 1. Go to Start  (All) Programs 802.11b/g MII Module Utility  Uninstall.
- 23 - 2. Click OK to complete remove the selected application and all of its features. 3. Click Finish to complete the uninstalled procedure.
- 24 - Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user＇s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Country Code Statement For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
- 25 - FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
- 26 - The final end product must be labeled in a visible area with the following " Contains TX FCC ID: MQ4WG2100 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu