Accton Technology BSG12 BUSINESS SERVICE GATEWAY User Manual BSG12ew Quick Installation Guide

Accton Technology Corp BUSINESS SERVICE GATEWAY BSG12ew Quick Installation Guide

INSTALLATION MANUAL 2

Tools and materialsInstalling the BSG unit For optional methods to install your BSG, see the BSG8ew and BSG12ew/aw/tw 1.0 Installation Guide (NN47928-302).Configuring the initial system settingsComplete the following steps using the BSG Quick Start Wizard. Before you start, contact your Internet service provider (ISP) to obtain your user name, password, and encapsulation type information (Ethernet, PPPoE).Connecting wirelessOptional installationsConnecting the Public Switched Telephone Network1012 Plug one end of an RJ-11 telephone cable into the FXO analog line (RJ-11) port on the front of the BSG. Plug the other end of the cable into the telephone jack on the wall.Attach the omni-directional antennas to the wireless LAN antenna connectors on the back of the BSG.BSG12ewBSG12ewQuick Installation Guide1467813141516171819523Before you install the Business Services Gateway (BSG), ensure that you have the following package contents and materials:Package Contents ● BSG unit ● power supply and power cord ● two omni-directional antennas ● console cable assembly ● Quick Installation Guide ● four self-adhesive rubber feet ● Regulatory sheet ● Hazardous Substance tableAdditional Required Materials (not included) ● standard Ethernet cable (WAN connection) ● two to three RJ-11 telephony cables (if using analog devices)You can download all documents referenced in this Quick Installation Guide at www.nortel.comPosition the BSG on a desktop. Make sure you leave enough space around the unit for ventilation and access to the cables.Install the power supply next to the BSG. The power supply must be within 1.5 m (5 ft) of the BSG and within 1.5 m (5 ft) of the AC power outlet (wall outlet or universal power supply).Connect the 48V DC 4-pin DIN power supply connector into either of the power outlets at the back of your BSG.From a PC connected to the LAN, open a new Web browser, type http://192.168.1.1 into the address bar, and press Enter to start the Web user interface.In the Login window, enter your user name (nnadmin) and password (PlsChgMe!), and click Login.In the navigation pane on the left, click Quick Start Wizard.Click the blue forward button to start the wizard. Click Next and enter information on each wizard page as required.On the Review Data page, click Continue. Congratulations! You have successfully configured the Nortel Business Services Gateway!Enter your ISP name, user name, and password, and confirm your password by entering it again. For more information about additional settings within the Quick Start Wizard, see the BSG8ew and BSG12ew/aw/tw 1.0 Configuration Guide (NN47928-500).Attach the four self-adhesiverubber feet to the bottom of the BSG by peeling off the paper backing and placing the feet on the unit.N0153680NN47928-304Standard 01.01Caution: Risk of equipment damageTo avoid damaging the equipment, you must connect the BSG to an outlet with a third-wire ground. Use the BSG with only the supplied BSG power supply and a three-wire power outletPlug one end of a standard Ethernet cable into one of the eleven LAN ports on the front of your BSG. Plug the other end of the Ethernet cable into your LAN device, such as a VoIP phone or PC.Ensure that the corresponding LAN port PoE/Link/Act LED lights up. The corresponding LED will come on only if the device connecting to that port is powered on.Connecting the WAN9WAN portPlug one end of the standard Ethernet cable into the WAN port (port 12) of the BSG. Plug the other end into the service provider’s cable modem or DSL modem.Connect one end of the AC power cord into the AC power supply. Plug the other end of the AC power cord into the AC power outlet (wall outlet or universal power supply).The System LED on the front panel lights up.Printed in Canada. Copyright © Nortel Networks Limited 2007. All Rights ReservedConnecting LAN devices (VoIP phones and PCs)Two power outletsConnecting analog or fax devices11 Plug one end of an RJ-11 telephone cable into either of the FXS analog telephone (RJ-11) ports on the front of the BSG. Plug the other end of the cable into the analog device.Console portFXO portFXS portsAttach feet herePoE/Link/Act LEDsLAN portsSystem LED

Navigation menu