Accton Technology ML6035 Metrolinq Outdoor 60GHz PTP + 5 GHz User Manual Metrolinq QSG R01 6pages 20151104

Accton Technology Corp Metrolinq Outdoor 60GHz PTP + 5 GHz Metrolinq QSG R01 6pages 20151104

UserManual.wiki >

Accton Technology >

ML6035 User Manual

Users Manual

Welcome to MetroLinqTM Interference-Free Gigabit Wirelessignitenet.com

UnboxingAfter opening the box, you will find…• MetroLinqTM• Bracket Kit• POE Power Supply• Power CableTools/Items Required• 13 mm Socket Wrench• Flat-Head Screwdriver• Ethernet Cables• (Optional) Alignment Scope ICC-SCOPE-9x50ignitenet.com2For helpful training and user-case information, please go to ignitenet.com/support

ignitenet.com3AssemblyThe MetroLinq™ bracket is designed for wall and pole mounting (25mm - 75mm pole diameter). Choose what is best for your location and select hardware accordingly. 1. Ensure all four position-locking bolts are tight before installing. 2. Install the bracket onto MetroLinq™ using four M8 bolts, lock washers, and flat washers.

Power Up1. Connect an Ethernet cable from the MetroLinq™ WAN port (right-side RJ-45) to the POE port on the power supply. 2. Connect Ethernet cable from the “LAN” port on the power supply to your LAN device. 3. Connect the power cord to a nearby AC power source.ignitenet.com4

AlignmentIgniteNet strongly recommends using the ICC-SCOPE-9x50 Alignment Scope for alignment. To install, place the scope on top of the MetroLinq™ housing and secure it with its thumb screw. ignitenet.com5Note: Do not adjust bolts A and B without first loosening 1 and 4 respectively.!1. Loosen coarse adjustment bolts 2 and 3 and set initial alignment. Don’tworry, you don’t have to be too accurate yet. After you have set the coarse alignment, tighten bolts 2 and 3.2. Loosen the horizontal fine-tune adjustment bolt 4. Use fine-tune bolt "B" to optimize the horizontal position. Re-tighten bolt 4.3. Loosen the vertical fine-tune adjustment bolt 1. Use fine-tune bolt "A" to optimize the vertical position. Re-tighten bolt 1.4. Initial alignment should be based on optical or visual alignment. After you achieve this, repeat steps 2 and 3 while watching the 60 GHz ignal strength LED. Optimize position to the LED indicator.5. Ensure all bolts are fully tightened, remove the alignment scope (if installed), and enjoy Gigabit interference-free wireless.B14A23

ignitenet.com61. Loosen coarse adjustment bolts 2 and 3 and set initial alignment. Don’tworry, you don’t have to be too accurate yet. After you have set the coarse alignment, tighten bolts 2 and 3.2. Loosen the horizontal fine-tune adjustment bolt 4. Use fine-tune bolt "B" to optimize the horizontal position. Re-tighten bolt 4.3. Loosen the vertical fine-tune adjustment bolt 1. Use fine-tune bolt "A" to optimize the vertical position. Re-tighten bolt 1.4. Initial alignment should be based on optical or visual alignment. After you achieve this, repeat steps 2 and 3 while watching the 60 GHz ignal strength LED. Optimize position to the LED indicator.5. Ensure all bolts are fully tightened, remove the alignment scope (if installed), and enjoy Gigabit interference-free wireless.Software1. To configure your MetroLinq, connect your computer to the LAN port on the device and configure the IP subnet to match the default IP address of 192.168.1.20 Once configured, direct your web browser to 192.168.1.20 and log in. username: root password: admin1232. After you have logged in, follow the steps in the Setup Wizard to configure the device for your network.For more configuration details and training, please go to ignitenet.com/support 150200001244A R01

FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 250 cm between the radiator & your body.

Navigation menu