Acoustic Arc AAI-AS0960US0 Wireless Speaker System User Manual

Acoustic Arc International Ltd. Wireless Speaker System

User Manual

AS0960US900Mhz Wireless StereoWaterproof Speaker SystemUser’s ManualPlease read before using the equipment
P.INTRODUCTIONThis stereo wireless speaker system applies the latest 900 MHz wirelesstechnology that enables you to enjoy music and TV sound anywhere inside oroutside your home. You can simply connect the transmitter with any audio sourcesuch as i-pod, TV, DVD, Hi-Fi and CD/MP3 player.FEATURES1. 900 MHz RF technology2. Auto Tuning System on speakers3. Phase Lock Loop (PLL) transmission system on transmitter4. Water-proof speakers5. Stereo Effect on Speakers6. Auto Pin Charging System7. Built-in Rechargeable Battery Pack8. Operating distance up to 100 meters.9. No line of sight limitation.10. Auto ON/OFF control on Transmitter11. Auto Shut-Off on Speakers
P.TRANSMITTER1. Connect the supplied AC power adaptor to an electrical wall outlet.2. Plug the AC power adaptor in the DC jack located on the rear of the transmitter.3. The rear of the transmitter has one audio cord that can be connected to audiooutput jack of TV, i-pod, DVD, and CD/MP3 players or to headphone/earphonejack with the connector provided.When the power adapter connection is finished, the LED of transmitter will light upin Green. When the audio cable connection is finished and turn on the audio source,the LED will turn from Green to Blue.SPEAKERS1. Charge the speakers by placing them on the transmitter station for 12 hoursbefore initial use.2. Press Power button and turn the speakers ON. The Power/Standby LED willlight up in Blue.
P.OPERATION1. Connect the power adapter between wall jack and transmitter. The LED will turnto Green.2. Turn on the audio source (TV or audio component) to which the transmitter isconnected with. The LED will turn from Green to Blue.3. Select the channel 1, 2 or 3 of the transmitter for best performance in yourlocation.4. Turn on the Power button on the speaker and adjust the volume by pressing “+”and “-“ for desired listening level. Volume can also be adjusted by pressing “+”and “-” button located on the remote control unit.5. Push the “SCAN” button to get the best tuning reception in the speakers.When the button is pressed, frequency tuning starts automatically and it stopswhen a signal is detected.6. You should now be able to place the speakers freely from room to room withoutdisruption.7. Press the LIGHT button to have mood-light effect. Press again for mood-lightoff. Power LED
P.SWITCHNG OFF1. If there is no audio input signal to transmitter in 4 minutes, transmitter will go tostandby mode and LED will change from Blue to Green.2. Tune the switch on the rear of transmitter to OFF.3. If the power adapter is unplugged, the LED on transmitter will turn off.4. Speaker will turn to standby mode if there is no input signal to transmitter andLED will become Green. Speaker will automatically shut off when standbymode continues for 5 minutes. At standby mode, speaker will turn to Onautomatically after getting signal from transmitter.TROUBLE SHOOTINGNO SOUND-Ensure the AC adaptor is fully inserted into the AC outlet and the powerconnection input on the transmitter.-Ensure the speaker is switch ON.-Speaker’s battery capacity is too low, recharge the speakers by placingthem on transmitter station.-Ensure the TV or audio component is ON.-The connected audio / video equipment is not playing. Start playing theequipment.-The volume of speaker is too low, adjust the volume to an appropriatelevel.DISTORTED-Press the “SCAN” button on the speakers until matching the frequency ofthe transmitter.-Change the position of the channel selector on the transmitter. Youmust then press the “SCAN” button on the speakers.-Battery capacity is too low. Recharge the speakers.-Ensure the volume level of speakers is adjusted properly.-The speaker is too far from transmitter, move closer.-The input level of the audio signal is too low. Turn up the volume of theaudio source equipment
P.TECHNICAL SPECIFICATIONSTransmission Mode:UHF stereoCarrier Frequency:900MHzOperation Voltage:Transmitter, DC14V 350mAFrequency Response:40Hz–12KHzDistortion:1.5%S/N Ratio:65dB (typical)Channel Separation:35dB (Typical)Operation Distance:Up to300feetOutput Power:2 x 5W (Max)WARNING : Changes or modifications to this unit not expressly approved by theparty responsible for compliance could void the user’s authority tooperate the equipment. Operation is subject to the following twoconditions: (1) this device may not cause interference, and (2) thisdevice must accept any interference, including interference thatmay cause undesired operation of the device.This device complies with RSS-210 of Industry and ScienceCanada. Operation is subject to the following two conditions : (1)this device may not cause interference, and (2) this device mustaccept any interference that may cause undesired operation of thedevice.The batteries shall not exposed to excessive heat such assunshine, fire or the likeFCC statementsThis device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received , including interference that maycause undesired operation. Wa rning: Changes or modificatio ns to this unit not express ly approved by the party responsible f orcompliance could void the user's authority to operate the equipment.
P.NOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonablepro tect ion ag ain st har mful in terf er ence in a resid enti al ins tall atio n. This equip men t g ene rates, usesand can radiate radio frequency energy and, if not installed and used in accordance with theins tructi ons, may cause har mful interfere nce t o radio comm unications. However, there is no guarantee that interference will not occur in a part icular installation. If thisequipment does cause harmful interfer ence to radio or television reception, which can be determinedby turning the equipment off and on, the us er is encouraged to try to correct the interfer ence by oneor more of the f ollow in g measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a ci rcuit different from that to whi ch the receiver isconnected.- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu