Acoustic Arc AAI-AS0960US0 Wireless Speaker System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1414696
Application ID	TJh9mb7wxUyk8iCSye3Ljg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.87kB (285898 bits)
Date Submitted	2011-02-09 00:00:00
Date Available	2011-02-09 00:00:00
Creation Date	2011-01-31 17:50:46
Producing Software	PDF-XChange 3.40.0078 (Windows XP)
Document Lastmod	0000-00-00 00:00:00
Document Title	User Manual

AS0960US
900Mhz Wireless Stereo
Waterproof Speaker System
User’
s Manual
Please read before using the equipment
INTRODUCTION
This stereo wireless speaker system applies the latest 900 MHz wireless
technology that enables you to enjoy music and TV sound anywhere inside or
outside your home.
such as i-pod,
You can simply connect the transmitter with any audio source
TV, DVD, Hi-Fi and CD/MP3 player.
FEATURES
1.
900 MHz RF technology
2.
Auto Tuning System on speakers
3.
Phase Lock Loop (PLL) transmission system on transmitter
4.
Water-proof speakers
5.
Stereo Effect on Speakers
6.
Auto Pin Charging System
7.
Built-in Rechargeable Battery Pack
8.
Operating distance up to 100 meters.
9.
No line of sight limitation.
10.
Auto ON/OFF control on Transmitter
11.
Auto Shut-Off on Speakers
P.
TRANSMITTER
1. Connect the supplied AC power adaptor to an electrical wall outlet.
2. Plug the AC power adaptor in the DC jack located on the rear of the transmitter.
3. The rear of the transmitter has one audio cord that can be connected to audio
output jack of TV, i-pod, DVD, and CD/MP3 players or to headphone/earphone
jack with the connector provided.
When the power adapter connection is finished, the LED of transmitter will light up
in Green. When the audio cable connection is finished and turn on the audio source,
the LED will turn from Green to Blue.
SPEAKERS
1. Charge the speakers by placing them on the transmitter station for 12 hours
before initial use.
2. Press Power button and turn the speakers ON. The Power/Standby LED will
light up in Blue.
P.
OPERATION
1. Connect the power adapter between wall jack and transmitter. The LED will turn
to Green.
2. Turn on the audio source (TV or audio component) to which the transmitter is
connected with. The LED will turn from Green to Blue.
3. Select the channel 1, 2 or 3 of the transmitter for best performance in your
location.
4. Turn on the Power button on the speaker and adjust the volume by pressing “+”
and “-“for desired listening level. Volume can also be adjusted by pressing “+”
and “-”button located on the remote control unit.
5. Push the “SCAN” button to get the best tuning reception in the speakers.
When the button is pressed, frequency tuning starts automatically and it stops
when a signal is detected.
6. You should now be able to place the speakers freely from room to room without
disruption.
7. Press the LIGHT button to have mood-light effect. Press again for mood-light
off.
Power LED
P.
SWITCHNG OFF
1.
If there is no audio input signal to transmitter in 4 minutes, transmitter will go to
standby mode and LED will change from Blue to Green.
2.
Tune the switch on the rear of transmitter to OFF.
3.
If the power adapter is unplugged, the LED on transmitter will turn off.
4.
Speaker will turn to standby mode if there is no input signal to transmitter and
LED will become Green. Speaker will automatically shut off when standby
mode continues for 5 minutes. At standby mode, speaker will turn to On
automatically after getting signal from transmitter.
TROUBLE SHOOTING
NO SOUND
Ensure the AC adaptor is fully inserted into the AC outlet and the power
connection input on the transmitter.
Ensure the speaker is switch ON.
Speaker’
s battery capacity is too low, recharge the speakers by placing
them on transmitter station.
Ensure the TV or audio component is ON.
The connected audio / video equipment is not playing. Start playing the
equipment.
The volume of speaker is too low, adjust the volume to an appropriate
level.
DISTORTED
Press the “SCAN”button on the speakers until matching the frequency of
the transmitter.
Change the position of the channel selector on the transmitter.
You
must then press the “SCAN”button on the speakers.
Battery capacity is too low. Recharge the speakers.
Ensure the volume level of speakers is adjusted properly.
The speaker is too far from transmitter, move closer.
The input level of the audio signal is too low. Turn up the volume of the
audio source equipment
P.
TECHNICAL SPECIFICATIONS
Transmission Mode
Carrier Frequency
Operation Voltage
Frequency Response
Distortion
S/N Ratio
Channel Separation
Operation Distance
Output Power
WARNING :
UHF stereo
900 MHz
Transmitter, DC 14V 350mA
40Hz –12KHz
1.5%
65dB (typical)
35dB (Typical)
Up to 300feet
2 x 5W (Max)
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’
s authority to
operate the equipment.
Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that
may cause undesired operation of the device.
This device complies with RSS-210 of Industry and Science
Canada.
Operation is subject to the following two conditions : (1)
this device may not cause interference, and (2) this device must
accept any interference that may cause undesired operation of the
device.
The batteries shall not exposed to excessive heat such as
sunshine, fire or the like
FCC statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
P.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
P.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Producer                        : PDF-XChange 3.40.0078 (Windows XP)
Create Date                     : 2011:01:31 17:50:46+08:00
Page Count                      : 7

EXIF Metadata provided by EXIF.tools