Acoustic Arc AAI-BH1410-00 ARC AUREM Bluetooth Earbuds User Manual 1
Acoustic Arc International Ltd. ARC AUREM Bluetooth Earbuds 1
User Manual
P/N: 95-08-BH1410US-02
Material: 128g C2S
折页：上、下对折（Logo 面朝外）
折页成品尺寸：260* 125mm
公差: +/- 1mm
“L” mark for left
USB Charge
QuickStartGuide
ContentsofthePackaging
1.ARCAuremwirelessearbudsx2(L&R)
2.USBtomircoUSBcable
3.ARCEarhookforARCAuremearbudsx2(L&R)
4.CarryingChargingCase
5.Earcushionx2(LargeandSmallsize)
Identifications
Power Button
“R” mark for right
Manual
Please visit our website WWW.ARCSTORE.ME to download the full user manual, if any
Warnings/Caution/General Information
Please check about warning information of the product container in separate sheets
or check in our full manual before initial usage of the product.
Warranty
Please register warranty service at our website WWW.ARCSTORE.ME
in 7 days after purchase
Hotline
Please get your support service at our Hotline : 1-844-ARC-7222
Copyright © 2014 ARC All rights reserved.
Get Ready To Use
1. ARC Aurem two pieces earbuds have been paired during manufacturing.
2. Press and hold Power button of L earbud for
5 seconds,LED ring will turn from Blue/Red to fast flashing Blue.
3. Turn on the Bluetooth device
4. Select “ARC Aurem” in the Bluetooth device.
5. Paired automaticall (Enter “0000” if password required)
6. Press and hold Power button of R earbud for 2 seconds,
7. Play music at the Bluetooth device
Phone
1. Make sure earbuds and cell are paired
2. Dial at cell and talk with earbuds
3. Accept incoming call by pressing Power button at L earbud
4. Refuse incoming call, press Power button for 2 seconds
Remark: Talk feature will only be activated on L earbuds.
FCC ID: VHC-AAI-BH1410-00 BC
LED ring will turn from Blue/Red to flashing Red.
8. Adjust volume level on the Bluetooth device
Reset
1. Turn the R earbud off
2. Press Power button for 12 seconds to clear old memory and reset
3. LED ring will flash between RED and BLUE three times
4. Repeat the above procedures on L earbud.
5. Start the processes of Pair processes
Pair (If not getting the earbuds start to work)
1. In case paring is needed, do the following procedures.
2. Press and hold Power button of L earbud 5 seconds,
LED ring will turn from Blue/Red to fast flashing Blue. Do the same for R earbud.
3. Fast press Power button of L earbud and LED ring turns to Red.
Slow press Power button twice of R earbud and LED ring turns toBlue/Red.
Both LED rings will flash slowly in Red when they are paired.
4. Press Power button of L earbud for 2 seconds to turn it off. Turn it on again
by pressing Power button for 5 seconds until LED ring flashes fast in Blue.
5. Turn on Bluetooth device and choose “ARC Aurem” for pairing.
6. LED rings flash slowly in Blue at L earbud ,and LED rings flash slowly in Red
7. LED rings flash slowly in Blue at both L & R earbuds when getting music to
both L & R earbuds.
at R earbud when pairing with Bluetooth device is completed.
8. Adjust volume level on the Bluetooth device
“The rating plate is located at the bottom enclosure of the apparatus.”
“ Battery shall not be exposed to excessive heat such as sunshine, fire or the like”
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
“ Warning for lithium battery”
ity This device complies with part 15 of the FCC Rules.