Acrox Technologies OPWISMMU01 2.4GHz Optical Mouse User Manual 410 1098 006B AMW25AP 07Aug31 full
Acrox Technologies Co., Ltd. 2.4GHz Optical Mouse 410 1098 006B AMW25AP 07Aug31 full
Manual
USER GUIDE
Features and specifications are subject to change without notice. All
trademarks are the property of their respective owners © 2007, Targus
Group International, Inc. and Targus, Inc. Manufacturer / Importer: Unit
1202-07, 12/F, Tower 2, Metroplaza, No. 223 Hing Fong Road, Kwai Fong,
N.T. Hong Kong
AMW25AP / 410-1098-006B
30
2.4GHz Optical Mouse
Model Name MA5
2.4GHz OPTICAL MOUSE
Introduction
Congratulations on your purchase of the 2.4GHz Optical Mouse
Notebook Mouse. This mouse features a tracking resolution switch
users who require more precision or speed with various application
The Stow-N-Go receiver clips onto the mouse for ease of use which
traveling or on the go. This mouse also features a 4-way scrolling
wheel which allows for both vertical and horizontal navigation.
• Hardware - USB port
• Windows® 2000/XP
• Windows Vista™
• Mac OS X 10.2.8 (or greater)
System Requirements
2
Installing the Batteries
2. Insert two AA-size batteries, making sure that the positive (+) and
negative (-) ends of each battery match the polarity indicators inside
the battery compartment. To replace the battery cover, place the
cover on top of the mouse and slide forward until it clicks into place.
NOTE: WHEN THE BATTERY IS LOW, THE LOW POWER INDICATOR LIGHT LOCATED
IN THE DPI SWITCHING BUTTON WILL FLASH RED. PLEASE REPLACE WITH TWO
NEW AA-SIZE BATTERIES.
1. Remove the battery cover from the back of the mouse by sliding off
the cover of the mouse. Hold the mouse in your hands and with the
back of the mouse away from you. Press down on the corners of the
battery cover and slide towards the back of the mouse. Lift the cover
off from the back of the mouse.
When power is on, the mouse goes into "sleep mode" after 8
minutes of inactivity. To activate the mouse, press any mouse key.
DPI switching
button
3
(A) Remove the USB receiver from the bottom of the mouse.
This will activate the on/off switch.
Establishing the Connection
(B)
(A)
(C)
(D)
(B) Plug the USB receiver into an available USB port on your computer.
(C) Press and release the setup key on the receiver.
(D) Press the setup key on the bottom of the mouse.
This device has 256 identification codes that allow the mouse and its
receiver to operate without interference from other radio frequency
devices. If you experience interference during use, repeat steps C and
D to change the connection channel.
NOTE: TO TURN THE MOUSE OFF, SIMPLY PLACE THE USB RECEIVER BACK INTO THE
STORAGE SLOT. THIS WILL MAXIMIZE BATTERY LIFE WHEN NOT IN USE.
4
This mouse is equipped with a 4-way scrolling function.
Installing the tilt-wheel software driver
To enable the tilt-wheel function, the software driver must be installed.
NOTE: PLEASE SELECT THE "3 BUTTON MOUSE" OPTION WHEN PROMPTED TO
DO SO.
2. The Installation Wizard window will prompt.
Follow the on-screen instructions to complete the installation.
After the software driver is successfully installed, there will be a “Tilt
Mouse” icon located in the task bar.
NOTE: THE TILT-WHEEL FEATURE IS SUPPORTED BY THE MAC OPERATING
SYSTEM. NO DRIVER INSTALLATION IS NECESSARY. THE FOLLOWING STEPS
ARE FOR WINDOWS OPERATING SYSTEMS ONLY.
1. Please download the software driver (Model # AMW25) from the
official Targus web site: http://www.targus.com
Save the setup.exe file to your computer and double click on the icon
to launch the installation process.
5
Pressing the scroll-wheel left or right, enables the horizontal scrolling
feature.
Using the 4-way scrolling tilt-wheel
NOTE: DOUBLE CLICK ON THE “TILT MOUSE” ICON IN THE TASK BAR WILL LAUNCH
THE MOUSE SETTINGS SCREEN. YOU CAN EDIT THE SETTINGS AND PREFERENCES
IN THIS WINDOW.
Activating the Universal Zoom function
The Universal Zoom function
can be enabled in the Mouse
Setting screen.
In the Mouse Setting screen,
under the Button tab, scroll
down the function list and select
the Universal Zoom function
then click Apply.
Press on the scroll wheel to
activate the zoom function.
6
Windows XP
Windows XP:
After selecting the desired resolution, you can also fine tune the
sensitivity. This can be adjusted in the “control panel” of the Windows
operating system.
Click on Start --> Setting --> Control Panel --> Mouse
In the “mouse properties” window, locate the “pointer options” tab.
Under “motion”, use the slider to change the speed of the mouse. Click
apply to confirm the changes.
Adjusting the DPI Setting
This mouse features 3 selectable resolution settings (1600 / 1200 /
800 DPI). By pressing the resolution switch, you can instantly adjust
the tracking speed of the mouse. When the DPI is set at 1600, the
indicator light will glow brightest and when it is set at 1200, the light will
become dimmer. The indicator will be off when the DPI is set at 800
DPI. The setting will be saved when the mouse is turned off. The
indicator light will shut off in 10 seconds after selecting the desired
resolution.
1600 DPI
1200 DPI
800 DPI
7
Transmitter
Receiver
RF • 2.4GHz
Interface • USB 1.1
Power • USB Bus Powered 5V DC
Product Specification
RF • 2.4GHz
Battery Type • Alkaline battery AA
Effective RF
Communication Range • 1.2 meters max
RF output Power • 1mW max
Power Consumption • 15mA max
This mouse is equipped with the latest sensor technology that conserves
power and provides up to six months of battery life. Battery life is determined
using one hour of continuous use, five days per week.
Mac OS
Mac OS:
After selecting the desired resolution, you can also fine tune the
sensitivity. This can be adjusted in the “System Preference” of the
Mac operating system.
Click on the Apple logo --> System Preference --> Keyboard & Mouse
In the “Keyboard & Mouse” window, locate the “Trackpad” tab. Under
“tracking speed”, use the slider to change the speed of the mouse.
8
Regulatory Compliance
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
FCC Statement
Te s t e d t o C o m p l y
This equipment has been tested and found to comply with the
limits of a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected;
• Consult the dealer or an experienced radio/TV technician for
help.
Declaration of Conformity
Hereby, Targus Group International, declares that this device is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Changes or modifications not authorized by the party responsible
for compliance could void the user’s authority to operate this
product.
Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries. All trademarks and registered
trademarks are the properties of their respective owners. All rights reserved.
9