Actiontec Electronics 802RUN2 Wireless Dual-Band USB Module User Manual
Actiontec Electronics Inc Wireless Dual-Band USB Module
User Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1983616 |
| Application ID | Txr+1WtB/x+SJQqg3+mfbA== |
| Document Description | User Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 27.92kB (349050 bits) |
| Date Submitted | 2013-06-05 00:00:00 |
| Date Available | 2013-12-02 00:00:00 |
| Creation Date | 2013-06-05 15:24:35 |
| Producing Software | Foxit Reader PDF Printer Version 6.0.3.0513 |
| Document Lastmod | 2013-06-05 17:32:02 |
| Document Title | User Manual.pdf |
W725D0 802.11ABGN 2T2R USB Module Page 1 of 12 Product Specification Model Name: W725D0 Part No.: WW725D0566A20H IEEE 802.11ABGN 2T2R USB Module Version: 1.1 Date: June. 5. 2013 W725D0 802.11ABGN 2T2R USB Module Page 2 of 12 Release History DATE REV Description of Change 2012/07/30 0.1 Preliminary specification release 2012/10/02 0.2 Add power consumption 2012/10/04 0.3 Update block diagram 2012/10/13 0.4 Update dimension and power consumption 2012/11/15 1.0 Change model name to W725D0, update RF Spec. 2013/5/7 1.0 Customized for Actiontec 2013/6/5 1.1 Delete dual MAC description and Modify FCC Label W725D0 802.11ABGN 2T2R USB Module Page 3 of 12 W725D0 IEEE 802.11ABGN 2T2 USB Module 1 Product Features Supports 2T2R 2.4/5GHz dual-band Maximum PHY data rate up to 144.4 Mbps using 20MHz bandwidth, 300Mbps using 40MHz bandwidth Short Guard Interval (400ns) Sounding packet Host interface complies with USB Specification Revision 2.0 Supports IEEE 802.11 e/ i/ h/ k WAPI (Wireless Authentication Pivacy Infrastructure) cerified Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU) Low latency immediate High-Throughput Block Acknowledgement (HT-BA) Long NAV for media reservation with CF-End for NAV release PHY-level spoofing to enhance legacy compatibility MIMO power saving mechanism Channel management and co-existence Supports Wake-On-WLAN via Magic Packet and Wake-up frame Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher multimedia bandwidth WiFi Direct supports wireless peer to peer applications. W725D0 802.11ABGN 2T2R USB Module 2 Block Diagram Page 4 of 12 W725D0 802.11ABGN 2T2R USB Module Page 5 of 12 3 General Specification Module Name W725D0 Product Specification WLAN Standard IEEE 802.11a/b/g/n USB 2.0 Host Interface Host Connector Options 4 pins header type connector Major Chipset Dimensions (board size) Realtek RTL8192DU Minimum Typical Maximum Unit Length 60.2 60.5 60.8 mm Width 22.4 22.6 22.8 mm Height 2.9 3.1 3.3 mm Weight 6.8 7.2 Minimum Typical Maximum Unit 4.74 5.25 70 °C Antenna Connector Options 2 printed PCB antennas on board Operating Condition DC Voltage Temperature Storage temperature -20 70 °C Humidity Non-Operating 10 80 Electrical Specification Frequency Range 2400 ~ 2483 MHz; 5150 ~ 5825 MHz Band Width 20MHz/ 40MHz Mixed mode 2.4GHz Band Output power 802.11b Minimum Typical Maximum Unit 15 17 19 dBm 802.11g 54Mbps 11 13 dBm 802.11n/ HT20 MCS7 11 dBm 802.11n/ HT40 MCS7 11 dBm Minimum Typical Maximum Unit Receiver Sensitivity 802.11b 11Mbps -80 dBm 802.11g 54Mbps -65 dBm 802.11n/ HT20 MCS7 -64 dBm W725D0 802.11ABGN 2T2R USB Module 802.11n/ HT40 Page 6 of 12 MCS7 -61 dBm 5GHz Band Output power Minimum Typical Maximum Unit 802.11a 54Mbps 10 12 dBm 802.11n/ HT20 MCS7 Lower/ Middle Band 11 dBm 802.11n/ HT20 MCS7 Upper Band dBm 802.11n/ HT40 MCS7 Lower/ Middle Band 11 dBm 802.11n/ HT40 MCS7 Upper Band dBm Minimum Typical Maximum Unit Receiver Sensitivit y 802.11a 54Mbps -65 dBm 802.11n/ HT20 MCS7 -64 dBm 802.11n/ HT40 MCS7 -61 dBm 4 Mechanical Dimension W725D0 802.11ABGN 2T2R USB Module Page 7 of 12 5 Power Consumption Test condition OS：Windows XP Channel 6：2437MHz Standard：IEEE802.11B,G.N Input voltage for whole circuit：4.97V TX uses continuous mode Test tool MP_Kit_RTL11n_DualMAC_9xD_USB_v019_20120307 5.1 Test result： Continuous TX/RX @ 2.4GHz Mode TX RX Standard Current (mA) mA DAC 1M 391 41 11M 238 41 6M 384 52 54M 384 52 HT20-MCS0 373 48 HT20-MCS7 373 48 HT40-MCS0 370 48 HT40-MCS7 371 48 1M 249 41 11M 249 41 6M 243 52 54M 243 52 HT20-MCS0 245 48 HT20-MCS7 245 48 HT40-MCS0 245 48 HT40-MCS7 245 48 W725D0 802.11ABGN 2T2R USB Module Page 8 of 12 Test condition OS：Windows XP Channel 165：5825MHz Standard：IEEE802.11A, AN Input voltage for whole circuit：4.97V TX uses continuous mode 5.2 Test result： MP_Kit_RTL11n_DualMAC_9xD_USB_v019_20120307 Continuous TX/RX @ 5GHz Mode TX RX Standard Current (mA) mA DAC 6M 377 46 54M 378 46 HT20-MCS0 369 42 HT20-MCS7 369 42 HT40-MCS0 395 42 HT40-MCS7 394 45 6M 242 46 54M 241 46 HT20-MCS0 241 42 HT20-MCS7 243 42 HT40-MCS0 244 45 HT40-MCS7 244 45 W725D0 802.11ABGN 2T2R USB Module Page 9 of 12 Test condition OS：Windows XP Channel 6：2437MHz Standard：IEEE802.11G,N RF output connects with AP (D-Link DIR-635, 2T3R) Input voltage for whole circuit：4.97V Throughput test mode Distance Limit: 1M (Signal & Quality 100%) Test driver Realtek, RTL8192DU_Drv_1016.1.0413.2012_UI_1.00.0180.All_In_One_Driver_Merge d_UI.L 5.3 Test result：Throughput test @2.4GHz Mode TX RX Standard Current (mA) Min Max 54M 197 210 HT20-MCS7 380 411 HT40-MCS7 275 382 54M 194 198 HT20-MCS7 186 201 HT40-MCS7 197 205 Uninstall Driver 20 Idle (Non Connect) 178 Idle (associated) 183 Driver disable 126 W725D0 802.11ABGN 2T2R USB Module Page 10 of 12 Test condition OS：Windows XP Channel 165：5825MHz Standard：IEEE802.11A,N RF output connects with AP (D-Link DIR-635, 2T3R) Input voltage for whole circuit: 4.97V Throughput test mode Distance Limit: 1M (Signal & Quality 100%) Test driver Realtek, RTL8192DU_Drv_1016.1.0413.2012_UI_1.00.0180.All_In_One_Driver_Merge d_UI.L 8.4 Test result：Throughput test @5GHz Mode TX RX Standard Current (mA) Min Max 54M 313 323 HT20-MCS7 332 356 HT40-MCS7 320 367 54M 271 281 HT20-MCS7 240 278 HT40-MCS7 243 276 Uninstall Driver 21 Idle (Non Connect) 168 Idle (associated) 245 Driver disable 140 W725D0 802.11ABGN 2T2R USB Module 10. Package Page 12 of 12 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. 2006/8/16 v1.0 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: LNQ802RUN2”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 2006/8/16 v1.0 Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Caution : (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. FOR MOBILE DEVICE USAGE Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 2496A-802RUN2”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 2496A-802RUN2". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. Caution : (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Annotate, Fill forms XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:06:05 15:24:35+08:00 Creator Tool : Modify Date : 2013:06:05 17:32:02+08:00 Metadata Date : 2013:06:05 17:32:02+08:00 Format : application/pdf Description : Creator : Title : Keywords : Producer : Foxit Reader PDF Printer Version 6.0.3.0513 Document ID : uuid:ba604520-6927-4c47-bc35-83714ddc19d6 Instance ID : uuid:a491959c-157a-4f5c-aa03-6f0481a5ecc0 Has XFA : No Page Count : 17 Subject : Author :EXIF Metadata provided by EXIF.tools