Actiontec Electronics GT701 54Mbps Wireless Gateway and Access Point User Manual

Download:
Mirror Download [FCC.gov]
Document ID	385747
Application ID	ZgZSNHaWoEgBjtrBT1d23g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.13kB (414127 bits)
Date Submitted	2003-12-31 00:00:00
Date Available	2003-12-31 00:00:00
Creation Date	2003-12-02 11:23:44
Producing Software	Acrobat Distiller 4.05 for Macintosh
Document Lastmod	2003-12-29 16:40:08
Document Title	Users Manual

QwstARK RedQS.qxd
12/2/03
11:20 AM
Page 1
Connect the Gateway to a Computer
Before proceeding, make sure you have received notification
from your phone company that your DSL line is active.
If you are installing DSL service
and have a monitored home
security alarm, Do Not continue
with this installation process.We
recommend calling your DSL
Service Provider for a technician
installation, or contacting your
security system provider for
further details. Please refer to
the Security section of the User
Manual for more information.
Step 4 Plug the larger end of
the Power Cord into a Power
Outlet.
Power
Outlet
Power
Cord
What are Phone Filters? Phone Filters separate the DSL signal
from the voice signal, allowing you to talk on the telephone
and be online at the same time.
Ethernet Light on Wireless DSL Gateway
Note: If the Ethernet Network Light does NOT turn green, make sure the Yellow
Cable is properly connected on both ends.
Step 5 Confirm the Power
Light on the Gateway is Green.
Power Light on Wireless DSL Gateway
Step 6 Get the Yellow Cable.
Yellow Port
Step 7 Plug one end of the
Yellow Cable into the Yellow
Port on the back of the
Wireless DSL Gateway.
Step 1 Get the Wireless DSL
Gateway from your DSL
Quick Start Kit and take it out
of the bag.
Yellow Cable
Wireless DSL Gateway
Step 8 Plug the other end
of the Yellow Cable in the
Ethernet Port on the back of
the computer.
Step 2 Get the Black Bag and
remove the Power Cord from
the bag.
Power Cord
Step 3 Plug the smaller end
of the Power Cord into the
Black Port on the back of the
Gateway.
Step 9 Confirm that the
Ethernet light on the
Gateway is Green. This may
take a few moments.
Black Port
An Ethernet Port looks similar
to a regular Phone Jack, but is
slightly larger.
Step 10 Get the Green DSL
Cable out of the Black Bag.
Step 11 Plug one end of the
Green Cable into the Green
Port on the back of the
Gateway.
Step 12 Plug the other end of
the Green Cable into the Phone
Jack closest to your computer.
Green Port
All Devices with the same phone number as your DSL Line
require Phone Filters. This includes telephones, fax machines,
caller ID boxes, and answering machines.
Step 1 Unplug your Telephones
(or other devices) from their
current Phone Jacks.
Green
Cable
Note: If you have a wall-mount telephone, you must install the Wall-Mount Phone
Filter. For all other telephones or other devices, use the small Phone Filters. To
install a Wall-Mount Phone Filter, see “Installing a Wall-Mount Phone Filter,” below.
Step 3 Plug a Phone Filter
into every Phone Jack in your
house with the same phone
number as your DSL Line, and
a telephone (or other device)
connected to it.
If you need additional Phone
Filters, contact your DSL
Service Provider.
Installing a Wall-Mount Phone Filter
Phone
Port
Caution: Do Not unplug the Green Cable from the Phone Jack near your Computer.
DSL Cable
Step 2 Open the Clear Bag
and remove the Phone Filters
from the bag.
Step 13 Confirm that the
Power and DSL Lights are
solid Green. This may take up
to 30 seconds.
1) Remove the wall-mount telephone from the wall jack.
2) Open the top and bottom toggles until they snap into the
open position.
3) Push the Wall-Mount Phone Filter into the wall jack, fully
inserting the plug on the back of the filter into the wall
jack opening.
4) Push the toggles back into the closed position until they
lock on the studs of the wall jack.
5) Reattach the telephone to the Wall-Mount Phone Filter.
Power & DSL Lights on Wireless DSL Gateway
Note: If the DSL Light continues to blink, make sure you received notification from
your DSL Service Provider that your DSL service is On. Otherwise, contact your
DSL Service Provider immediately.
Note: The number and type of Phone Filters included in this kit may vary.
Caution: Do Not connect a Phone Filter into the Phone Jack near your Computer
(the Phone Jack into which your Green Cable is plugged).
Power Cord
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
Install the Phone Filters
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
Step 4 Plug one end of the Phone
Cord into the Phone Filter and
keep the other end attached to
the telephone (or other device).
Step 1 Open a Web browser
(Netscape Navigator or Internet
Explorer, for example). In the
address bar, enter
http://192.168.0.1, then press
Enter on the keyboard.
To Install a Telephone next to your Computer:
Step 1 Find the Phone Cord
connected to the Telephone next to
your Computer. Unplug this Phone
Cord from the Phone Jack it is
currently plugged into (you may
have already unplugged the cable
during the modem installation
process). Keep the other end
connected to the Telephone.
Configure the Gateway
Phone
Jack
Step 2 The “Main Menu” screen
appears. Select
Setup/ Configuration.
Phone
Cord
Step 3 Click Non-Windows
Setup in the left-hand column
of the “Set Up/Configuration”
screen.
Step 5 Click Save and Restart at the bottom of the Actiontec
DSL Modem Setup Page to save your changes.
The Wireless DSL Gateway is now configured and ready for
use. For more information regarding technical support, please
review the Start Here Guide.
If you received a Block of IP addresses from your Internet Service
Provider, follow the instructions in Section 4 of this Guide,
“Configure a Block of IP Addresses.” Otherwise, go to Section 5,
“Configure a Single IP Address.”
Note: If you have a Macintosh Computer, see section 6,“Setup a Macintosh
Computer,” at the end of this Quick Start Guide.
Note: Do Not unplug the Green cable from the Phone Jack near your computer.
Step 2 Plug the Phone Cord
into the Port marked “Phone” on
the back of the Gateway. Do Not
plug the Phone Cord into the
back of your Computer.
Make sure you have connected
your Phone to the Gateway
exactly as shown in the picture to
the right.
Note: The phone port on the Gateway includes a built-in microfilter. As a result,
no additional filter is needed.
Questions? Call toll-free at 1-800-247-7285
Step 4 The “Actiontec DSL Modem
Setup Page” screen appears.
Follow the onscreen instructions.
Have your Internet Service
Provider (ISP) Worksheet handy
and use it to fill in the text boxes
in the Actiontec DSL Modem
Setup Page.
Security Notice
Don’t be a victim! Secure your DSL service from unwanted
intrusions. Please refer to the Security section of your User
Manual for more information regarding network security.
If you have not received your ISP
Worksheet, contact your ISP. The
Worksheet is provided separately
from this kit by your ISP.
Flip this Quick Start Guide over to continue 
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
QwstARK RedQS.qxd
12/2/03
11:20 AM
Page 2
Configure a Block of IP Addresses
Note: The information required to configure a block of IP addresses is provided
by your ISP. If this information has not been provided, contact your ISP.
Step 1 Click Setup in the top
menu.
Step 5 Make sure the circle
next to Obtain an IP Address
through PPPoA is selected.
Step 6 Check the box next to
Unnumbered Mode.
Configure a Single IP Address
Note: The information required to configure a single IP address is provided by
your ISP. If this information has not been provided, contact your ISP.
Step 4 Click WAN IP Address
in the left-hand column in the
“Configuring the Advanced
Settings” screen.
Step 1 Click Setup in the top
menu.
Step 5 Click the circle next to
the type of WAN IP Address
you have, then click Next.
Step 2 Click Advanced Setup
in the left-hand column of the
“Set Up/Configuration” screen.
Step 7 Enter the
information for the
Unnumbered IP Address.
Click Next.
Step 3 Click Begin Advanced
Setup in the next screen.
Step 2 Click Advanced Setup
in the left-hand column of the
“Set Up/Configuration” screen.
Step 8 Enter your User Name
and Password.
Step 4 Click WAN IP Address
in the left-hand column of the
“Configuring the Advanced
Settings” screen.
Step 9 Click Save and Restart
in the left-hand column.
Setup a Macintosh Computer
Before connecting a Wireless Wireless DSL Gateway to a
Macintosh computer, the computer must be set up for networking. Use the following procedure.
Step 5 When the User Mode
window appears, select
Advanced, then click OK.
Step 1 Click the Apple in the
upper right corner of the menu
bar to reveal the Apple Menu.
Step 6 Enter your User Name,
Password and Static IP address.
Step 7 Click Save and Restart
in the left-hand column.
Step 6 In the TCP/IP window,
select Ethernet from the
Connect via pop-up menu.
Step 7 Select Using DHCP
Server from the Configure
pop-up menu.
Step 3 From the Control
Panels menu, click TCP/IP.
Step 9 Click Options, and when
the TCP/IP Options window
appears, select Active. Make
sure the Load only when
needed option is Not checked,
then click OK.
Step 11 Restart the Computer.
The Computer is now set up
for networking.
Note: MSN Users with MAC OS-X and Later: In order to complete your MSN
installation and activate your MSN Account, insert the disk labeled “Windows
Users: Put this CD in FIRST”.
• Access your CD-ROM drive.
• Open the MSN for MAC folder.
• Double click on the “MSN for MAC OS X.dmg” file.
• Follow the instructions provided in the installation software.
Congratulations! You have successfully installed your Wireless
DSL Gateway. You can now access the Internet at high speed.
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
Questions? Call toll-free at 1-800-247-7285
Wireless DSL Gateway
For All Users (Including Non-Windows Users)…
This Quick Start Guide will walk you through the
easy steps to set up your Wireless DSL Gateway.
During this process, we’ll show you how to:
Questions? Call toll-free at 1-800-247-7285
Connect the Gateway to a Computer
Install the Phone Filters
Configure the Gateway
Configure a Block of IP Addresses
Configure a Single IP Address
Setup a Macintosh Computer
You will need the following items from your
Actiontec Quick Start Kit:
Step 8 Ensure the Use 802.3
option is Not checked.
DSL
• Wireless
Gateway
• Black Bag
Part No.: 0530-0427-001
Questions? Call toll-free at 1-800-247-7285
Quick Start Guide
Step 10 Close the TCP/IP
window and when prompted
to save changes, click Save.
Note: The procedure below is for the Macintosh operating systems version 9.2.2
and below. For computers running Macintosh OS X, see the User Manual.
Step 2 From the Apple Menu,
click Control Panels.
Step 3 Click Begin Advanced
Setup in the next screen.
Step 4 When the TCP/IP
window appears, select Edit
from menu bar, then select
User Mode.
Questions? Call toll-free at 1-800-247-7285
• Yellow Cable
• Clear Bag
NEXT


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:12:02 11:23:44Z
Modify Date                     : 2003:12:29 16:40:08-08:00
Page Count                      : 4
Creation Date                   : 2003:12:02 11:23:44Z
Producer                        : Acrobat Distiller 4.05 for Macintosh
Mod Date                        : 2003:12:29 16:40:08-08:00
Metadata Date                   : 2003:12:29 16:40:08-08:00

EXIF Metadata provided by EXIF.tools