Actiontec Electronics WCB5200 11ac Wireless Network Extender User Manual pt 2

Download:
Mirror Download [FCC.gov]
Document ID	2938245
Application ID	sjWExHJT0OJ9NyLoThLqEA==
Document Description	User Manual pt 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.16kB (426965 bits)
Date Submitted	2016-03-22 00:00:00
Date Available	2016-09-18 00:00:00
Creation Date	2015-07-15 11:34:01
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-07-15 11:34:02
Document Title	User Manual pt 2
Document Creator	Adobe InDesign CS6 (Macintosh)

General Regulatory and Compliance Notices
Important Safety Instructions
If applicable, when using telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical
shock, and personal injury, including the following:
• Do not use this product near water – for example, near a bathtub, kitchen sink, laundry tub, or swimming pool, or in a wet basement;
• Avoid using a telephone (other than a cordless type) during an electrical storm, as there may be a remote risk of electrical shock
due to lightning;
• Do not use the telephone to report a gas leak in the vicinity of the leak;
• Use only the power cord and batteries indicated in this manual;
• Do not dispose of batteries in fire, as they may explode – check with local codes for possible special disposal instructions.
Telephone Line Cord Caution
To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord.
Coaxial Cable
If applicable, the coaxial cable screen shield needs to be connected to the Earth at the building entrance per ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, “Grounding of Outer Conductive Shield of a Coaxial Cable,” or in accordance with local regulation.
For Audio/Video Apparatus
This reminder is provided to call the CATV system installer’s attention to Section 820.93 of the National Electric Code (NEC), which
provides guidelines for proper grounding and, in particular, specifies that the coaxial cable shield shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
Please heed all warnings; read, keep and follow all instructions. Do not use this apparatus near water and only clean with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources
such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat.
FCC Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try and correct the interference by implementing one or more of the following measures:
• Reorient or relocate the receiving antenna;
• Increase the separation between the equipment and receiver;
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected;
• Consult the dealer or an experience radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Actiontec Electronics, Inc, may void the user’s authority to operate the equipment.
Declaration of conformity for products marked with the FCC logo – United States only.
This devices complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference;
2.This device must accept any interference received, including interference that may cause undesired operation of the device.
Important Note
If applicable, this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 30 cm between the radiator and your body.
For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible.
The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note
that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by
the technology.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile
satellite systems.
The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for pointto-point and non point-to-point operation as appropriate.
The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
For questions regarding your product or the FCC declaration, contact:
Actiontec Electronics, Inc
760 North Mary Avenue, Sunnyvale, CA 94085, United States
Tel: (408) 752-7700 Fax: (408) 541-9003
PN 0530-0601-002
PI1176/0113

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2015:07:15 11:34:01-07:00
Metadata Date                   : 2015:07:15 11:34:02-07:00
Modify Date                     : 2015:07:15 11:34:02-07:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:e5ecc238-b2ce-2c44-925b-fa822f8fa485
Original Document ID            : xmp.did:B26052191B2068118083E618D7D027F5
Document ID                     : xmp.id:FE7F117407206811808386CBDFB88431
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:FD7F117407206811808386CBDFB88431
Derived From Document ID        : xmp.did:FD7F117407206811808386CBDFB88431
Derived From Original Document ID: xmp.did:B26052191B2068118083E618D7D027F5
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2015:07:15 11:34:02-07:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools