Adams Rite 80 0180 4591MA_C 459XMA Paddle Operator Installation Instructions 4591 4591MA C

User Manual: Adams Rite 459XMA Paddle Operator Installation Instructions Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 2

24 VAC
115 VAC LINE
POWER
SOURCE
C
ACTUATING
SWITCH
BLACK
N.C
N.O
RED
WHITE
LOAD
4580 CAM DISC HANDING
STEP 3
TURN THE CAM DISC OVER
AND RE-INSTALL THE CAM
PIVOT PIN AS SHOWN
LOOKING AT THE EDGE OF THE DOOR, DETERMINE ON WHICH
SIDE THE HANDLE OR OTHER OPERATOR IS TO BE INSTALLED.
THE CAM DISC MUST BE
HANDED AS SHOWN.
STEP 2
DO NOT REMOVE
THE DRIVER PIECE
PULL THE CAM PIVOT PIN OUT
OF THE CAM DISC AS SHOWN.
STEP 4
SNAP THE RETAINER CLIP
INTO THE GROOVE ON THE
CAM PIVOT PIN.
STEP 1
REMOVE THE
RETAINER CLIP
ON THIS SIDE
THE CAM DISC MUST BE
HANDED AS SHOWN.
ON THIS SIDE
SUGGESTED
WIRING DIAGRAM
wwww.adamsrite.com
Phone: 800-626-7590 Fax: 866-582-4641
459XMA PADDLE OPERATOR
INSTRUCTIONS FOR CHANGING HAND OF 4580 CAM DISC
80-0180-4591MA REV C
CR 322-14
STEP 2
1. INSTALL 4700 SERIES DEADLATCH
PER MOUNTING INSTRUCTIONS.
2. INSTALL 4580 CAM DISC ASSEMBLY
ANDSECURE WITH SET SCREW.
(SEE REVERSE FOR CAM DISC
HANDING).
4580
CAM DISC
SET
SCREWS
.63"
1.718"
3.00"
BACKSET OF
DEADLATCH
STEP 1
1. PREPARE STILE AS SHOWN.
2. INSERT BINDER POST THRU Ø.328 HOLE IN STILE.
3. SECURE BINDER POST WITH 5/16-24 NUT.
Ø1.25"
CYLINDER
C
L
LATCH
CUTOUT
2X Ø.328" +.312"/-0"
BINDER
POST
5/16-24
NUT
C
L
.50"
STEP 3
ESCUTCHEON
ASSEMBLY
1. INSTALL ESCUTCHEON ASSEMBLY.
ROUTE WIRING THRU
.50 HOLE.
2. USING 10-32 SEM SCREWS, SECURE
ESCUTCHEON ASS'Y. TO BINDER POST.
IMPORTANT
TIGHTEN THESE SCREWS SECURELY.
SEM SCREW
DRIVE PLATE
DRIVER EARS
STEP 4
1. INSTALL PADDLE ASS'Y. ALIGN DRIVE EARS
ON PADDLE WITH SLOT IN DRIVER PLATE.
2. INSTALL PIVOT PIN.
3. INSTALL PIVOT PIN SET SCREW. TIGHTEN SET
SCREW FLUSH WITH BOTTOM OF ESCUTCHEON.
LABEL
PIVOT PIN
SET SCREW
PADDLE
ASSEMBLY
REMOVE THE DOGGING
SCREW WHEN USED IN
PULL CONFIGURATION
SPRING
DRIVER PLATE
DRIVER SCREW
PIN
KEEPER
INSIDE
RH
RHR
TOP
DRIVER
SCREW
DRIVER
SCREW
LHR
OUTSIDE
PULL TO LEFT
LH
1. FIND DESIRED CONFIGURATION.
2. REMOVE KEEPERS TO SEE LOCATION
OF SPRING & DRIVER PLATE.
3. REVERSE SWITCH IF NECESSARY.
4. IF NECESSARY, REMOVE SPRINGS
AND DRIVER PLATE.
5. MOVE ROLL PIN TO DESIRED LOCATION.
6. REPLACE DRIVER PLATE & SPRING.
PIN ON
FAR SIDE
PIN ON
FAR SIDE
PUSH TO LEFT
PUSH TO RIGHT
PULL TO RIGHT
7. REMOVE DRIVER SCREW IF NECESSARY
AND PLACE IN DESIRED LOCATION.
8.. REPLACE KEEPERS.
INSTALLATION
INSTRUCTIONS FOR CHANGING HAND
www.adamsrite.com
Phone: 800-626-7590
Fax: 866-582-4641
459XMA PADDLE OPERATOR
80-0180-4591MA REV C
CR 322-14

Navigation menu