Adams Rite 80 0180 348_1 P8700 Install Instructions Proof Installation AR Pullman Exit Device
User Manual: Adams Rite P8700 Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 1
1
2a
LEFT HAND REVERSE
RIGHT HAND REVERSE
2b
4
5
3
Patent pending and/or patent www.assaabloydss.com/patents
Copyright © 2020, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in
whole or in part without the express written permission of Hanchett Entry Systems, Inc. is prohibited. 80-0180-348_1
Cut-o Instructions for Non-standard Doors
1. Drive out two roll pins.
2. Remove mounting cap.
3. Collapse bar and tape down area of cut-o.
4. Determine extrusion length (“B” dim)
NOTE: 3-5/8” Minimum dimension from rivet centerline to new cut-o length as shown.
5. Measure mounting bar (not push bar) and mark extrusion length on tape.
6. Saw o excess length, remove tape and debur.
7. Lay mounting cap over mounting bar and use as a guide to drill two 1/8” dia. holes.
8. Re-install mounting cap into mounting bar and drive two roll pins into holes.
Separating Push Bar and Mounting Bar Procedure
1. Remove both end caps.
2. Slide push bar toward the hinge side of the door.
3. Continue to slide the push bar past the pivot plate that rides in push bar track.
4. Slide push bar in opposite direction keeping pivot plate out of track until pushbar is free of mounting plate.
Determine bar height and use provided templates to drill pilot holes in door and frame.
NOTE: If installing cylinder or trim, drill prep holes during this step as well. See 2b for details.
*SKIP STEPS 2a AND 2b IF NO OUTSIDE TRIM OR
CYLINDER IS BEING INSTALLED
Install trim cam and trim cam plate on underside of exit bar as shown below.
Ensure trim cam has proper engagement before installing bar onto door.
Install bar onto door frame using the provided #10 x 1-1/4"
self tapping screws. Do not fully tighten screws until bar
and strike have been properly adjusted.
Use TEMPLATE C to cut 1-1/4"
hole into outside surface of door
then install cylinder.
Install strike onto frame. Do not fully tighten screws until bar
and strike have been properly adjusted.
Use #2 Phillips head screw driver to install end caps.
NOTE: screws are contained inside end cap assembly.
Ax cylinder plate to cylinder.
Ensure holes on plate align with
holes for exit bar mounting screws.
P8700 RIM EXIT DEVICE
INSTALLATION INSTRUCTION
INSTALLING PUSH BAR TO MOUNTING BAR
With push bar in hand and mounting bar attached to door. Find stop plate staked into push bar (this
plate is on the latch end of assembled unit). Slide the pivot plate nearest hinge into track of push bar
until second pivot plate is exposed. Insert pivot plate into track on push bar and slide in opposite
direction until push bar and mounting bar align.
Minus 5"
Door Opening
Dim "B"=
Pilot Holes
1/8" Diameter
Masking Tape
Push Bar
Mounting
Cap
Roll Pin
3-5/8" Min
Mounting Bar
29/64" From
mounting centerline
to center hole
BAR HEIGHT
CENTERLINE
CYLINDER
CENTERLINE
1/8"
1/4"
Use screws
provided with
cylinder
13/32"
Using TEMPLATE C
Cut 1-1/4" hole
13/16" Between cylinder
mounting screws
MOUNTING
CENTERLINE
*NOTE: Consult cylinder manufacturer installation instructions before drilling holes
for cylinder mounting screws. Template shows center mounting screw location.
HOLLOW METAL DOOR
Use TEMPLATE M to cut
3/8" hole for cylinder
spindle and two (2) 7/32 x
82 C'sink holes for
cylinder mounting screws
WOOD DOOR
29/64" MOUNTING
CENTERLINE
BAR HEIGHT
CENTER LINE
Use screws
provided with
cylinder
EXIT BAR
MOUNTING
SCREWS
CYLINDER
PLATE
1/8"
Use TEMPLATE
hole for outside
cylinder W to
cut 1-1/4"
"
A
"
MOUNTING
CENTERLINE
Use TEMPLATE M or TEMPLATE W
(depending on door type) to drill two
1/8" pilot holes for mounting screws
BAR HEIGHT
CENTERLINE
Use STRIKE
TEMPLATE to drill
two (2) 5/32" pilot
holes for #10 self
tapping screws
(If using rivnuts,
drill two (2) 1/4"
pilot holes)
STRIKE
MOUNTING
SURFACE
1-1/2"
2"
1"
1"
1-3/4"
Drill two (2) 1/8" pilot holes
for lock down screws after
bar is fully adjusted
7/16"
7/8"
11/16"
Use TEMPLATE H to drill
two (2) 1/8" pilot holes for
mounting screws
1-3/8"
1-11/32"
3/4"
End Cap
Push Bar
Pivot Plate
Stop Plate
End Cap and Retainer Assembly
Mounting Bar
If using rivnuts, use rivnut tool
provided in frame kit to install
#10 x 3/4" Self Tapping Screws
(2 Required)
NOTE: Lockdown screw is to be installed after strike
and bar have been properly adjusted
4-40 x 5/16"
Screws
Trim Cam
Plate
Trim Cam
#10 x 1-1/4" Self Tapping
Screw (4 Required)
NOTE: Install lock down
screws once bar and strike
are fully adjusted. Slide
Push Bar towards the hinge
side to access the lock
down screw mounting holes.
Retainer
Latch Side
End Cap
Hinge Side
End Cap
“A”
2511/16"
DOOR WIDTH
30"
36"
42"
48"
3111/16"
3711/16"
4311/16"
