Addvalue Communications SABRE1WE WIDEYE SABRE 1 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	773958
Application ID	GoMUKwxCHLDtrRVw1/btqg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	232.78kB (2909745 bits)
Date Submitted	2007-03-29 00:00:00
Date Available	2007-05-08 00:00:00
Creation Date	2007-03-02 15:37:32
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2007-03-02 15:37:32
Document Title	Microsoft Word - Quick Start User Guide for Alpha1_Chris_041006.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	leeping.miau

Quick Start User Guide
for SABRE™ I
1. Inserting SIM card and Battery
1.1 Inserting the SIM Card
I.
Insert the SIM card (gold-contacts facing downwards) into the SIM slot.
II.
Ensure the SIM card is inserted in the position as shown.
SIM Card
1.2 Inserting the Battery
I.
Insert the battery in the direction as shown.
SIM Card
Battery Door
II.
Battery
Slide in the battery door and ensure that it is locked into position.
For Alpha Only
1-1
1.3 Charging the Battery
I.
Insert the AC/DC Power Adapter connector into the Charger socket.
Charger socket
AC/DC Power
Adapter connector
II.
Switch on the main power.
III.
Do not remove the battery from the SABRE™ I during charging.
IV.
When the battery is fully charged, remove the AC/DC Adapter connector
from the Charger Socket.
Note: It takes approximately 3 hours to fully charge the battery.
Note: When the SABRE™ I Terminal is switched ON, the charging time
will be longer.
Note:
An animated icon to show that the internal battery of the
SABRETM I Terminal has completed charging while the SABRETM I
Terminal is non-operational (switched off).
Note:
An animated icon to show that the internal battery of the
SABRETM I Terminal is undergoing charging while the SABRETM I
Terminal is non-operational (switched off).
1-2
For Alpha Only
Ethernet Port
Phone Port
On/Off Switch
Charger Socket
Built-in Compass
LCD
Up Button
Top Status
Area
Enter
Button
Main Display Area
Return
Button
Bottom Status
Area
Down Button
For Alpha Only
1-3
2
Powering Up and Registering to Network
2.1
Powering Up
I.
Press and hold the On/Off switch for at least 3 seconds
II.
The LCD display will show the Introductory screen.
2.2
Terminal and SIM PINs (4 to 8 digits)
I.
Enter the Terminal PIN number. (Default Terminal PIN: 0000)
(Note: If the Pin is entered incorrectly or if user forgets the terminal’s Pin
number, send the unit back to the distributor)
II.
1-4
Enter the SIM PIN number.
For Alpha Only
(Note: If the SIM PIN is entered incorrectly after 3 attempts, the PIN will
be locked. Use the PUK (Personal Unblocking Key) code to enter new
SIM PIN. If the PUK code is entered incorrectly after 10 attempts, the
SIM will be disabled. Contact the Service Provider.)
2.3
GPS Fix
I.
For first time use, SABRE™ I needs to acquire the GPS coordinates, go
to an outdoor location and have the SABRE™ I face up to the sky. The
terminal shall perform the GPS acquisition automatically.
II.
When acquisition is done, the LCD display will show New GPS fix for 2
seconds.
III.
LCD will indicate the new estimated azimuth direction and elevation
angle that the antenna should point. A GPS indicator will be displayed
on the Top Right corner of the LCD display to indicate that a New GPS
coordinate is in use.
For Alpha Only
1-5
IV.
For subsequent use, the SABRE™ I will not acquire a new GPS, it will
prompt the user if the previously stored GPS coordinates should be used.
To use the stored GPS coordinates, use the Up/Down buttons to select
Yes and press ENTER. A GPS indicator will indicate the use of stored
GPS coordinates.
To re-acquire a new GPS, select No and press ENTER. The SABRE™ I
terminal will repeat Step I to III.
V.
2.4
1-6
Press the ENTER button then the LCD will show the signal strength bar.
Antenna Pointing
I.
SABRE™ I is now in Antenna Pointing state.
II.
To obtain the maximum possible signal strength, adjust the antenna by
turning and tilting it. For an acceptable services to commence, a signal
For Alpha Only
strength of minimum 45 dBHz is required. Press ENTER when the
maximum possible signal strength is obtained.
Turning
Tilting
III.
SABRE™ I will start the registration with the network.
IV.
When registration is successful, the service provider’s name will be
displayed.
For Alpha Only
1-7
3
Making Phone Calls
3.1 Using Corded Analog Handset
I.
Connect the Corded Analog Phone to SABRE™ I via the RJ11 phone
port.
II.
Making phone calls directly –
a.
III.
Making phone calls via Phonebook –
a.
1-8
to listen dial-tone before
Corded Analog Handset: Press the
dialing and dial the calling party number in the following format;
<00><#>
Use the Up/Down buttons to select
For Alpha Only
b.
Scroll to the calling party’s name and Press ENTER.
c.
Press the
tone.
d.
Use the Up/Down buttons to select
e.
Press ENTER to start the dialing sequence.
button of the Corded Analog Handset to listen dial-
3.2 Using the Bluetooth Headset
I.
Perform the pairing and connection procedures before proceeding with
the following. (Bluetooth device pairing and connection procedures are
found in Section 6 Bluetooth Settings on SABRE™ I)
II.
Making phone calls via Phonebook –
Use the Up/Down buttons to select
For Alpha Only
1-9
a.
Scroll to the calling party’s name and Press ENTER.
b.
Press the Connect button of the Bluetooth Headset to listen dial-tone.
Connect button
c.
1-10
Use the Up/Down buttons to select
For Alpha Only
d.
Press ENTER to start the dialing sequence.
3.3 Using the Bluetooth Handset
I.
Perform the pairing and connection procedures before proceeding with
the following. (Bluetooth device pairing and connection procedures are
found in Section 6 - Bluetooth Settings on SABRE™ I)
II.
Making phone calls directly –
III.
a.
Bluetooth Handset: Enter the calling party number in the following
format; <00> (Calling
numbers will be displayed in the LCD).
b.
Press the
button to start the dialing sequence.
Making phone calls via Bluetooth Handset Phonebook (To be Available)
For Alpha Only
1-11
4
Installing PC programs (For Alpha)
I.
Insert the Product CD into the PC and go to CD Drive.
II.
The following drivers and application are available on the CD for
installation:
a. Ethernet driver
b. Bluetooth Dongle driver
c. BGAN LaunchPad.
III.
1-12
If BGAN LaunchPad is selected, follow the installer’s instructions.
a.
When prompted for the BGAN LaunchPad edition, select Personal
Edition.
b.
Continue to follow the instructions until installation is completed.
IV.
If Ethernet is required, the respective device driver must be installed in
the PC before connecting the Network cable into the respective ports on
the SABRE™ I. Refer to Section 7 – Ethernet Setup for the installation
steps.
V.
If Bluetooth Dongle is required, please refer to Section 8 – Installation
of Bluetooth Dongle driver
For Alpha Only
5
Cable Connections
I.
There are various methods of connecting the SABRE™ I to the PC. Use
only 1 method.
Ethernet – Connect one end of the network cable to the PC’s network
socket and the other end to the RJ45 Ethernet Port.
For Alpha Only
1-13
6
Bluetooth Settings on SABRE™ I
6.1 Enable Bluetooth
I.
From the LCD, use the Up/Down buttons to select Menu > Settings >
Interfaces > Bluetooth > Enable.
Note: Bluetooth is enabled by default.
II.
The LCD will display “Bluetooth enabled!” for 2 seconds and revert
back to > Bluetooth.
6.2 Pairing of Bluetooth Devices
I.
II.
1-14
From the LCD, use the Up/Down buttons to select Pairing of Device.
The LCD will display “Searching…”.
For Alpha Only
III.
After searching, the LCD will display a list of devices for pairing. Select
a Bluetooth device from the list for pairing. (Devices of the same brand
and type may appear as the same name on the list.)
IV.
Enter the Bluetooth device PIN. (Wideye Bluetooth Headset default PIN
is 0000)
V.
The LCD will display “Pairing…”.
VI.
When successfully paired, the LCD will display “Paired successfully!”
for 2 seconds and revert back to > Bluetooth.
6.3 Connecting to a paired Bluetooth Device
I.
From the LCD, use the Up/Down buttons to select Paired list.
II.
From the list, use the Up/Down buttons to select the paired device to be
connected and Press ENTER.
III.
Use Up/Down buttons to select Connect and Press ENTER.
IV.
The LCD will display the Bluetooth profiles supported on the device.
V.
Use Up/Down buttons to select appropriate profile, for example for
Bluetooth Headset select HSP and Bluetooth Dongle select SPP1 or
SPP2.
For Alpha Only
1-15
VI.
1-16
When connected, the LCD will display ”Connected successfully!” for 2
seconds and revert back to > Bluetooth.
For Alpha Only
7
Ethernet Setup
7.1 Installation of Ethernet Driver
I.
Double click on the Ethernet Driver Folder.
II.
Click Setup to begin the installation process.
III.
From the Installation Wizard welcome window, click Next.
For Alpha Only
1-17
1-18
IV.
Select I accept the terms of the license agreement and click Next.
V.
Enter user name and company (if any) and click Next.
For Alpha Only
VI.
If there is a need to change the folder where the setup will install the files,
click Change, after making the change click Next to proceed. If change is
not needed, click Next to proceed immediately.
For Alpha Only
1-19
1-20
VII.
Select or unselect the components to be installed and click Next.
VIII.
Click Install.
For Alpha Only
IX.
Click Finish.
X.
An Addvalue Configuration Utility icon will be added on the Desktop.
XI.
Double-click the icon to open Addvalue Configuration Utility.
XII.
Configure only the followings:
•
From the VCOM Port pull-down menu – Choose any available
Virtual COM Port for the Modem to be created. (For example:
COM 11)
•
IP Address of BGAN: 192.168.1.35
(This is also known as the SABRE™ I’s Local IP Address)
For Alpha Only
1-21
7.2 Creating A New Modem
I.
1-22
From Control Panel, select Phone and Modem Options.
For Alpha Only
II.
Select the “Modem” tap and click Add.
III.
Check “Don’t detect my modem; I will select it from a list” and click
Next.
For Alpha Only
1-23
IV.
From the Manufacturer list, choose (Standard Modem Types) and from
the Models list, choose Standard 19200 bps Modem and click Next.
V.
From Selected Ports, For Ethernet: select the same COM Port number
that was created with Addvalue Configuration Utility (For example COM
11), For Bluetooth: select the two COM Port numbers that was assigned to
the when SABRE I pairing was performed with the Bluetooth dongle, and
click Next.
1-24
For Alpha Only
VI.
Click Finish.
For Alpha Only
1-25
7.3 Setup the DUN Client
I.
From Win XP Desktop, click Start, select All Programs > Accessories >
Communications > New Connection Wizard.
II.
From New Connection Wizard, click Next.
III.
Select Connect to the network of my workplace and click Next.
1-26
For Alpha Only
IV.
Select Dial-up connection and click Next.
V.
Check on the modem that was created earlier in 7.2 and click Next.
For Alpha Only
1-27
VI.
Enter a Company Name (for example Any Name) and click Next.
VII.
Enter *98*1# and click Next.
1-28
For Alpha Only
VIII.
Select Anyone’s use and click Next.
IX.
Check Add a shortcut to this connection to my desktop and click
Finish.
For Alpha Only
1-29
X.
1-30
The DUN Client shortcut icon will be created on the Desktop.
For Alpha Only
7.4 Ethernet settings on SABRE I
7.4.1
Defining PDP Context:
I.
From the LCD, use the Up/Down buttons to select Menu and press
ENTER. Select Settings > Network > Data > Automatic and Press
ENTER.
7.4.2
TAF Mode: Proceed with the following steps if TAF settings are required:
(Note: By default, the SABRE I is set to TAF mode.)
I.
From the LCD, use the Up/Down buttons to select Menu and press
ENTER. Select Settings > Interfaces > Ethernet > Connectivity > TAF
Connection and Press ENTER.
II.
Use the Up/Down buttons to select Enable and Press ENTER.
III.
From the PC, open the DUN Client - double-click on the DUN Client
icon.
IV.
Click Dial to start connection. Username and Password are not required.
V.
Open the Internet Browser to begin “Surfing”.
For Alpha Only
1-31
7.4.3
I.
IP Transparent Mode:
From the LCD, use the Up/Down buttons to select Menu and press
ENTER. Select Settings > Interfaces > Ethernet > Connectivity > IP
Connection and Press ENTER.
II.
Use the Up/Down buttons to select Enable and press ENTER.
III.
Use the Up/Down buttons to select Authentication > PAP and Press
ENTER. Press RETURN to revert back to the previous menu.
IV.
Use the Up/Down buttons to select DNS setting > Dynamic and Press
ENTER.
V.
1-32
Use the Up/Down buttons to select Connect and Press ENTER.
For Alpha Only
VI.
From the PC, double-click on the Local Area Connection icon (located at
the bottom right corner of the PC monitor)
VII.
Select Properties
For Alpha Only
1-33
VIII.
1-34
Select and check Internet Protocol (TCP/IP) and click Properties.
For Alpha Only
IX.
Select Obtain an IP address automatically and Obtain DNS server
address automatically and click OK.
X.
Close all the windows.
XI.
Open the Internet Browser to begin “surfing”.
For Alpha Only
1-35
8
1-36
Installation of Bluetooth Dongle Driver
I.
From the Bluetooth Dongle Driver folder, double-click on Setup.
II.
Select the language and click “OK”
III.
Click “Next”
For Alpha Only
IV.
Click “Yes”
V.
Click “Next”
For Alpha Only
1-37
VI.
Select “Yes” and click “Finish” to Restart the PC. Now the driver for the
USB Bluetooth dongle and connection application are installed into the
PC.
VII.
After restart, the IVT application will open. Insert the Bluetooth dongle in
a USB port. The PC will detect the dongle automatically.
VIII.
Perform Bluetooth setup as described in Section 6 Bluetooth Settings on
SABRE™ I. The COM Ports will be assigned for the serial connection.
IX.
1-38
Create a New Modem – Refer to Section 7 - 7.2 Creating a New Modem
For Alpha Only

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2007:03:02 15:37:32+08:00
Modify Date                     : 2007:03:02 15:37:32+08:00
Page Count                      : 38
Creation Date                   : 2007:03:02 07:37:32Z
Mod Date                        : 2007:03:02 07:37:32Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : leeping.miau
Metadata Date                   : 2007:03:02 07:37:32Z
Creator                         : leeping.miau
Title                           : Microsoft Word - Quick Start User Guide for Alpha1_Chris_041006.doc

EXIF Metadata provided by EXIF.tools