Ademco 04007500 Microwave/PIR motion sensor User Manual

Honeywell International Inc. Microwave/PIR motion sensor Users Manual

04007500 User Manual PDF Download & Text

Users Manual

Download:
Mirror Download [FCC.gov]
Document ID	992099
Application ID	Ub9/8CXbRee1Rofv6hQVcQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	125.52kB (1568945 bits)
Date Submitted	2008-08-28 00:00:00
Date Available	2008-08-28 00:00:00
Creation Date	2008-05-28 13:17:35
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2008-05-29 11:00:02
Document Title	Users Manual

DT7500SN V-PlexTM DUAL TEC Motion Sensor - Installation Instructions
LOCATION / EMPLACEMENT / POSIZIONAMENTO / LOCALIZACIÓN / LOCATION
OPEN / OUVERTURE / APERTURA / APERTURA / OPEN
Use these holes when
mounting to a standard
U.S. electrical junction box
MOUNT / INSTALLATION / MONTAGGIO / MONTAJE / MOUNT
Microwave Walk Test ON
Anti-Mask ON
OFF 1
OFF 1
2.1 - 2.4 m
(7 - 8 ft)
0.3-1.3mm
(22-16 AWG)
Rear Tamper Breakaway Tab
Rear Tamper Breakaway Tab
Rear Tamper Breakaway Tab
Rear Tamper Breakaway Tab
Rear Tamper Breakaway Tab
LED Enabled
Pet Immune Lens (included)
Pet Immune Lens (included)
Pet Immune Lens (included)
Pet Immune Lens (included)
Pet Immune Lens (included)
6 a
75%
High Sensitivity
Pulse Count 2
Low Sensitivity
LED Disabled
Microwave Walk Test OFF
Anti-Mask OFF
Pulse Count 2
Low Sensitivity
LED Disabled
Microwave Walk Test OFF
Anti-Mask OFF
Pulse Count 2
Low Sensitivity
LED Disabled
Microwave Walk Test OFF
Anti-Mask OFF
Pulse Count 2
Low Sensitivity
LED Disabled
Microwave Walk Test OFF
Anti-Mask OFF
LED Enabled
Microwave Walk Test ON
Anti-Mask ON
Low Sensitivity
LED Disabled
Microwave Walk Test OFF
Anti-Mask OFF
High Sensitivity
LED Enabled
Pulse Count 1
High Sensitivity
LED Enabled
Microwave Walk Test ON
Anti-Mask ON
Pulse Count 1
High Sensitivity
LED Enabled
Microwave Walk Test ON
Anti-Mask ON
Microwave Walk Test ON
Anti-Mask ON
High Sensitivity
Pulse Count 1
If installed with a Smart V-PlexTM Panel:
The sensor will not transmit or indicate intrusion alarms
when the panel is disarmed; in the armed state, the sensor
will respond to all communications to or with the host panel.
If installed with a Standard V-PlexTM Panel:
The sensor will respond to all communications with the
host panel armed or disarmed.
Look-Down Mask (install as shown when using Pet Immune Lens)
Look-Down Mask (install as shown when using Pet Immune Lens)
Look-Down Mask (install as shown when using Pet Immune Lens)
Look-Down Mask (install as shown when using Pet Immune Lens)
Look-Down Mask (install as shown when using Pet Immune Lens)
High Sensitivity: 1 - 2 Steps; No Pet Immunity
High Sensitivity: 1 - 2 Steps; No Pet Immunity
High Sensitivity: 1 - 2 Steps; No Pet Immunity
High Sensitivity: 1 - 2 Steps; No Pet Immunity
High Sensitivity: 1 - 2 Steps; No Pet Immunity
If installed with a Smart V-PlexTM Panel: The sensor will not
transmit or indicate intrusion alarms when the panel is disarmed;
in the armed state, the sensor will respond to all communications
to or with the host panel.
If installed with a Standard V-PlexTM Panel: The sensor will
respond to all communications with the host panel, armed or
disarmed.
If installed with a Smart V-PlexTM Panel: The sensor will not
transmit or indicate intrusion alarms when the panel is disarmed;
in the armed state, the sensor will respond to all communications
to or with the host panel.
If installed with a Standard V-PlexTM Panel: The sensor will
respond to all communications with the host panel, armed or
disarmed.
If installed with a Smart V-PlexTM Panel: The sensor will not
transmit or indicate intrusion alarms when the panel is disarmed;
in the armed state, the sensor will respond to all communications
to or with the host panel.
If installed with a Standard V-PlexTM Panel: The sensor will
respond to all communications with the host panel, armed or
disarmed.
If installed with a Smart V-PlexTM Panel: The sensor will not
transmit or indicate intrusion alarms when the panel is disarmed;
in the armed state, the sensor will respond to all communications
to or with the host panel.
If installed with a Standard V-PlexTM Panel: The sensor will
respond to all communications with the host panel, armed or
disarmed.
IDENTIFY COMPONENTS AND SELECT APPROPRIATE SETTINGS / IDENTIFICATION DES COMPOSANTS ET SÉLECTION DES PARAMÈTRES APPROPRIÉS / IDENTIFICARE I COMPONENTI
E SELEZIONARE LE IMPOSTAZIONI APPROPRIATE / IDENTIFICAR LOS COMPONENTES Y SELECCIONAR LA CONFIGURACIÓN ADECUADA / IDENTIFY COMPONENTS AND SELECT
APPROPRIATE SETTINGS
50%
Range Adjustment
Réglage de la portée hyper
Regolazione della portata
Ajuste del rango de detección
Range Adjustment
Pulse Count 1
OFF 1
Pulse Count 1
100%
Pulse Count 2
25%
ON
ON
Wide Angle Lens (installed)
Wide Angle Lens (installed)
Wide Angle Lens (installed)
Wide Angle Lens (installed)
Wide Angle Lens (installed)
T V- V+
LED
REPLACE CIRCUIT BOARD / REMISE EN PLACE DU PCB /
RIPOSIZIONARE IL CIRCUITO / VOLVER A COLOCAR LA
PLACA DE CIRCUITO IMPRESO / REPLACE CIRCUIT
BOARD
WIRE / CABLAGE / COLLEGAMENTO / CABLEADO / WIRE
Polling Loop
9 - 13VDC
SMB-10T
TAMPER
24 VDC,
10mA
OFF 1
Cover Tamper Switch
Contact AP du capot
Interruttore tamper sul
coperchio
Tamper de la cubierta
Cover Tamper Switch
T T - +
OFF 1
OFF 1
ON
OFF 1
ON
ON
OFF 1
ON
ON
Medium Sensitivity: 1 - 3 Steps; No Pet Immunity
Medium Sensitivity: 1 - 3 Steps; No Pet Immunity
Medium Sensitivity: 1 - 3 Steps; No Pet Immunity
Medium Sensitivity: 1 - 3 Steps; No Pet Immunity
Medium Sensitivity: 1 - 3 Steps; No Pet Immunity
ON
With SMB10T
With SMB10T
With SMB10T
With SMB10T
With SMB10T
With SMB10T
OFF 1
Low Sensitivity: 2 - 4 Steps; Up to 23 kg (50 lb) Pet Immunity
Low Sensitivity: 2 - 4 Steps; Up to 23 kg (50 lb) Pet Immunity
Low Sensitivity: 2 - 4 Steps; Up to 23 kg (50 lb) Pet Immunity
Low Sensitivity: 2 - 4 Steps; Up to 23 kg (50 lb) Pet Immunity
Low Sensitivity: 2 - 4 Steps; Up to 23 kg (50 lb) Pet Immunity
ON
OFF 1
Lowest Sensitivity: 3 - 5 Steps; Up to 45 kg (100 lb) Pet Immunity
Lowest Sensitivity: 3 - 5 Steps; Up to 45 kg (100 lb) Pet Immunity
Lowest Sensitivity: 3 - 5 Steps; Up to 45 kg (100 lb) Pet Immunity
Lowest Sensitivity: 3 - 5 Steps; Up to 45 kg (100 lb) Pet Immunity
Lowest Sensitivity: 3 - 5 Steps; Up to 45 kg (100 lb) Pet Immunity
ON
DT7500SN V-PlexTM DUAL TEC Motion Sensor - Installation Instructions
!b
!b
!b
Note: Pet immunity characteristics for this sensor have not been verified by
Underwriter’s Laboratories, Inc.
Note: Pet immunity characteristics for this sensor have not been verified by
Underwriter’s Laboratories, Inc.
Note: Pet immunity characteristics for this sensor have not been verified by
Underwriter’s Laboratories, Inc.
FOR PET IMMUNITY
• Mount the center of the sensor at 2.3 m (7.5 feet) high.
• Set the sensor to the Lowest or Low sensitivity (see step 6a).
• Install Pet Immune lens (5-532-489-01 - see Lens Change
Instructions on page 3).
• Install the look-down mask (see Step 6a).
• Install the sensor where pets cannot come within 1.8 m (6 ft) of the
sensor by climbing on furniture or other objects.
• Aim the sensor away from stairways, furniture or other objects that
can be climbed on by pets.
• TEST the installation site to determine the exact level of attainable
animal immunity.
FOR PET IMMUNITY

• Mount the center of the sensor at 2.3 m (7.5 feet) high.
• Set the sensor to the Lowest or Low sensitivity (see step 6a).
• Install Pet Immune lens (5-532-489-01 - see Lens Change
Instructions on page 3).
• Install the look-down mask (see Step 6a).
• Install the sensor where pets cannot come within 1.8 m (6 ft) of the
sensor by climbing on furniture or other objects.
• Aim the sensor away from stairways, furniture or other objects that
can be climbed on by pets.
• TEST the installation site to determine the exact level of attainable
animal immunity.
Note: Pet immunity characteristics for this sensor have not been verified by
Underwriter’s Laboratories, Inc.
Note: Pet immunity characteristics for this sensor have not been verified by
Underwriter’s Laboratories, Inc.
PROGRAM SENSOR SERIAL NUMBER ID
Each sensor has a factory-assigned serial number which must be
entered into the control panel during the zone programming procedure.
The unique serial number can be found on a bar code label on the
sensor PCB. The serial number can be entered into the control panel in
one of the following methods:
A. Download it through software (Zone definition screen of Compass
software). This is recommended for large installations and
installations where foot traffic cannot be controlled.
B. Enter the number through the keypad at the “INPUT S/N” prompt
during manual zone programming. Ensure no other polling devices
are activated when manually entering the sensor serial number.
C. Activate the sensor twice while at the “INPUT S/N” prompt during
manual zone programming.
To enter the sensor’s serial number for option B or C:
Refer to the control panel’s manual for programming instructions.
TM
For all V-Plex panels, enter INT FOLLOWER 04 for the Zone Type and
“06” for SL (Serial Polling Device) at the “INPUT TYPE” prompt. For
Smart V-PlexTM panels press “1” (Yes) for SMART CONTACT.
At the “INPUT S/N” prompt, either enter the serial number (and “1” for
the loop number), or fault the sensor (wave your hand in front of the
sensor or activate the tamper), then wait 3-6 seconds and fault the
sensor again. The keypad will beep after each fault to confirm the signal.
The sensor should now be enrolled. If a “1” does not appear under the
“L” on the zone summary screen, press [*] and enter the loop number
manually at the next screen.
Refer to the control panel’s manual for programming instructions.
TM
For all V-Plex panels, enter INT FOLLOWER 04 for the Zone Type and
“06” for SL (Serial Polling Device) at the “INPUT TYPE” prompt. For
Smart V-PlexTM panels press “1” (Yes) for SMART CONTACT.
At the “INPUT S/N” prompt, either enter the serial number (and “1” for
the loop number), or fault the sensor (wave your hand in front of the
sensor or activate the tamper), then wait 3-6 seconds and fault the
sensor again. The keypad will beep after each fault to confirm the signal.
The sensor should now be enrolled. If a “1” does not appear under the
“L” on the zone summary screen, press [*] and enter the loop number
manually at the next screen.
NORMAL WALK TEST – 10 MINUTES
Normal walk test mode activates after power up mode and remains
active for 10 minutes. For an additional 10 minutes of walk test time,
remove and replace the front cover. In walk test mode, the LED is
always enabled, regardless of the LED DIP switch setting. [Note: if the
TM
panel is not a Smart V-Plex panel, walk test can also be done by
enabling the LED (DIP switch 3 = ON.]
Walk through the detection area and observe the LED.
If necessary, adjust the microwave range, pulse count or sensitivity
setting. (For LED activation meaning, refer to the LED Indicator table
below.)
Normal walk test mode activates after power up mode and remains
active for 10 minutes. For an additional 10 minutes of walk test time,
remove and replace the front cover. In walk test mode, the LED is
always enabled, regardless of the LED DIP switch setting. [Note: if the
TM
panel is not a Smart V-Plex panel, walk test can also be done by
enabling the LED (DIP switch 3 = ON.]
Walk through the detection area and observe the LED.
If necessary, adjust the microwave range, pulse count or sensitivity
setting. (For LED activation meaning, refer to the LED Indicator table
below.)
MICROWAVE WALK TEST – 10 MINUTES
1. Set the Microwave Walk Test DIP switch to ON, or toggle it ON and
OFF.
2. Set Range Adjustment potentiometer to 25% and replace the cover.
3. Walk through the detection area and observe the LED.
4. If necessary, adjust the potentiometer until desired detection range is
obtained. (For LED activation meaning, refer to the LED Indicator
table below.)
Indicator LEDs
Condition
Indicator LED
Power Up
Slow Blinking Red (will finish within
60 seconds)
Red ON for 3 seconds if Alarm
Yellow ON for 2 seconds if Microwave
event detected
Green ON for 2 seconds if PIR event
detected
Power Up
Slow Blinking Red (will finish within
60 seconds)
Red ON for 3 seconds if Alarm
Yellow ON for 2 seconds if Microwave
event detected
Green ON for 2 seconds if PIR event
detected
Red ON if Microwave is set too high
Green ON if Microwave is set correctly
OFF if Microwave is set too low
Fast Blinking Red (LED Enabled
or Disabled)
Microwave Walk Test
Trouble or Anti-Mask
Rotule de montage
Snodo da parete
Rotula de montaje a pared
Swivel Mount Bracket
SMB-10C
(P/N 0-000-111-01)
Swivel Mount Ceiling Bracket
Rotule de plafond
Rotula de montaje a techno
Swivel Mount Ceiling Bracket
SMB-10T
(P/N 0-000-155-01)
Swivel Mount Bracket w/Tamper
EN 50131-1 &
EN50131-2-4
NCompliant
Snodo da parete con tamper
DT7000-LRLK
15 m x 3 m
(50’ x 10’)
Long Range Lens Kit
Rotule de montage avec autoprotection
Rotula de montaje a pared con tamper
Swivel Mount Bracket w/Tamper
Kit lentille longue portée
Kit lenti a lunga portata
Kit de lentes de largo alcance
Long Range Lens Kit
DT7000-HSLK
11 m x 12 m
(35’ x 40’)
High Security Lens Kit
High Security Lens Kit
High Security Lens Kit
High Security Lens Kit
High Security Lens Kit
DT7000-PALK
11 m x 12 m
(35’ x 40’)
Pet Alley Lens Kit
Pet Alley Lens Kit
Pet Alley Lens Kit
Pet Alley Lens Kit
Pet Alley Lens Kit
LENS CHANGE INSTRUCTIONS / LENS CHANGE INSTRUCTIONS /
LENS CHANGE INSTRUCTIONS / LENS CHANGE INSTRUCTIONS /
LENS CHANGE INSTRUCTIONS
Indicator LEDs
Indicator LED
Microwave Walk Test
Swivel Mount Bracket
MICROWAVE WALK TEST – 10 MINUTES
1. Set the Microwave Walk Test DIP switch to ON, or toggle it ON and
OFF.
2. Set Range Adjustment potentiometer to 25% and replace the cover.
3. Walk through the detection area and observe the LED.
4. If necessary, adjust the potentiometer until desired detection range is
obtained. (For LED activation meaning, refer to the LED Indicator
table below.)
Condition
Normal Walk Test
SMB-10
(P/N 0-000-110-01)
Snodo da soffitto
PROGRAM SENSOR SERIAL NUMBER ID
Each sensor has a factory-assigned serial number which must be
entered into the control panel during the zone programming procedure.
The unique serial number can be found on a bar code label on the
sensor PCB. The serial number can be entered into the control panel in
one of the following methods:
A. Download it through software (Zone definition screen of Compass
software). This is recommended for large installations and
installations where foot traffic cannot be controlled.
B. Enter the number through the keypad at the “INPUT S/N” prompt
during manual zone programming. Ensure no other polling devices
are activated when manually entering the sensor serial number.
C. Activate the sensor twice while at the “INPUT S/N” prompt during
manual zone programming.
To enter the sensor’s serial number for option B or C:
NORMAL WALK TEST – 10 MINUTES
ACCESSORIES / ACCESSOIRES / ACCESSORI / ACCESORIOS /
ACCESSORIES
Normal Walk Test
Trouble or Anti-Mask
Red ON if Microwave is set too high
Green ON if Microwave is set correctly
OFF if Microwave is set too low
Fast Blinking Red (LED Enabled
or Disabled)
% ANTI-MASK
% ANTI-MASK
When DIP switch 5 is set to ON, the sensor indicates a mask condition
(see LED Indicator table above) when a variety of materials and
reflective objects are placed in front of it. Follow the mounting guidelines
in step 1 to avoid false mask alarms.
To clear a mask condition, visually inspect the sensor and remove any
materials blocking the sensor’s view. The sensor will clear an anti-mask
condition when three valid alarms are detected. After a mask condition
is cleared, fully walk test the required detection area.
When DIP switch 5 is set to ON, the sensor indicates a mask condition
(see LED Indicator table above) when a variety of materials and
reflective objects are placed in front of it. Follow the mounting guidelines
in step 1 to avoid false mask alarms.
To clear a mask condition, visually inspect the sensor and remove any
materials blocking the sensor’s view. The sensor will clear an anti-mask
condition when three valid alarms are detected. After a mask condition
is cleared, fully walk test the required detection area.
TROUBLESHOOTING
TROUBLESHOOTING
RED LED flashing rapidly during normal operation indicates a trouble or
an anti-mask condition. If the sensor is not masked (see step 10), either
a microwave, PIR, or temperature compensation fault is present.
RED LED flashing rapidly during normal operation indicates a trouble or
an anti-mask condition. If the sensor is not masked (see step 10), either
a microwave, PIR, or temperature compensation fault is present.
Solution: Momentarily power down the sensor. If the trouble does not
clear, replace the sensor. (Please check the power, all wiring and that
the sensor is not masked before replacing the sensor.)
Solution: Momentarily power down the sensor. If the trouble does not
clear, replace the sensor. (Please check the power, all wiring and that
the sensor is not masked before replacing the sensor.)
DETECTION PATTERNS / COUVERTURE DE DETECTION / DIAGRAMMA DI COPERTURA /
PATRON DE DETECCIÓN / DETECTION PATTERNS
LENS MASKING / LENS MASKING / LENS MASKING / LENS
MASKING / LENS MASKING
35’ / 11m Pet Immune Lens (P/N 5-532-489-01 – Included)
Install Look Down Mask to block look down zones.
Install Look Down Mask to block look down zones.
Install Look Down Mask to block look down zones.
Install Look Down Mask to block look down zones.
Install Look Down Mask to block look down zones.
- Page 3 -
5-532-489-01
Side View / VUE DE COTE / Vista in sezione /
VISTA LATERAL / Side View
25 / 35FT
TOP
Top View / VUE DE DESSUS / Vista in pianta / VISTA DESDE ARRIBA / Top View
DT7500SN V-PlexTM DUAL TEC Motion Sensor - Installation Instructions
SPECIFICATIONS
CARACTERISTIQUES
SPECIFICHE TECNICHE
ESPICIFICACIONES
SPECIFICATIONS
Range: 50’ x 60’ (15 m x 18 m) [installed]
35’ x 40’ (11 m x 12 m) [included]
Portée: 15 m x 18 m [installed]
(11 m x 12 m) [included]
Portata: 50’ x 60’ (15 m x 18 m)
[installed]; 35’ x 40’ (11 m x 12 m)
[included]
Covertura: 15 m x 18 m [installed]
(11 m x 12 m) [included]
Range: 50’ x 60’ (15 m x 18 m) [installed]
35’ x 40’ (11 m x 12 m) [included]
Tamper Switch: (NC) 10 mA,
24 VDC
Autoprotection: (NC) 10 mA,
24 VDC
Interruttori antimanomissione: (NC) 10
mA, 24 VDC
Salida de tamper: (NC) 10 mA,
24 VDC
Tamper Switch: (NC) 10 mA,
24 VDC
Power Requirements: 9 - 13 VDC @
polling loop terminals with reverse polarity
detection; nominal 11.0 VDC polling loop
Alimentation: 9 - 13 VDC @ polling loop
terminals with reverse polarity detection;
nominal 11.0 VDC polling loop
Alimentazione: 9 - 13 VDC @ polling
loop terminals with reverse polarity
detection; nominal 11.0 VDC polling loop
Requerimientos de alimentación: 9 - 13
VDC @ polling loop terminals with reverse
polarity detection; nominal 11.0 VDC
polling loop
Power Requirements: 9 - 13 VDC @
polling loop terminals with reverse polarity
detection; nominal 11.0 VDC polling loop
Current: 3.0 mA nominal (with LED
disabled); 6.0 mA nominal (with LED
enabled); 6.5 mA max. (during warm up)
Current: 2.5 mA nominal (with LED
disabled; 5.0 mA nominal (with LED
enabled
Current: 2.5 mA nominal (with LED
disabled; 5.0 mA nominal (with LED
enabled
Current: 2.5 mA nominal (with LED
disabled; 5.0 mA nominal (with LED
enabled
Current: 3.0 mA nominal (with LED
disabled); 6.0 mA nominal (with LED
enabled); 6.5 mA max. (during warm up)
Frequency: 24.125 GHz (K-band)
Hyperfréquence: 24.125 GHz
(K-band)
Frequenza microonda: 24.125 GHz (Kband)
Frecuencias Microondas: 24.125 GHz
(K-band)
Frequency: 24.125 GHz (K-band)
PIR White Light Immunity: 6,500 Lux
typical
Immunity à la lumière blanche: 6,500
Lux Typique
Immunita PIR alla luce bianca: 6,500
Lux tipica
Immunidad contra luces blancas: 6,500
Lux typical
PIR White Light Immunity: 6,500 Lux
typical
Fluorescent Light Filter: 50 Hz or 60
Hz, auto-detection
Filtre lumière Fluorescente: 50 Hz or 60
Hz, sélectionnable
Filtro luce Fluorescente: 50Hz o 60Hz,
selezionabile
Filtro Luz Fluorescente: 50 Hz or 60 Hz,
selectable
Fluorescent Light Filter: 50 Hz or 60
Hz, auto-detection
Operating Temperature: -4° to 131° F
(-20° to 55° C), 5% - 95% relative humidity
(non-condensing)
Température de fonctionnement:
-20° à 55° C; Humidité relative: 5% à 95%
sans condensation
Temperatura di esercizio: da -20° a 55°
C; 5% - 95% umidità relative (noncondensansante)
Temperatura de funcionamiento: -4° to
131° F (-20° to 55° C); Humedad relativa:
5% to 95% sin condensación
Operating Temperature: -4° to 131° F
(-20° to 55° C), 5% - 95% relative humidity
(non-condensing)
Self-Tests:
Microwave supervision; End-to-End PIR
self-test; Temperature Compensation
Auto-Tests:
Supervision hyperfréquences; IRP;
Compensation en température
Auto-Tests:
Supervisione Microonda; Auto-test PIR;
Comp. Temperatura
Auto-Test:
Supervisión Microondas; Test PIR; Comp.
Temp.
Self-Tests:
Microwave supervision; End-to-End PIR
self-test; Temperature Compensation
Temperature Compensation: Advanced
Dual Slope
Compensation en température: A
double pente
Compensazione Temperatura:
Avanzata a doppio gradiente
Compensación de temperatura: Doble
pendiente avanzada
Temperature Compensation: Advanced
Dual Slope
PIR Fields of View:
Wide Angle Lens (P/N 5-532-439-00)
44 long range zones
12 intermediate zones
6 lower zones
4 look-down zones
Champ de détection IRP:
Grand Angle Lens (P/N 5-532-439-00)
44 faisceaux longs
12 intermediaires
6 courts
4 verticaux
Zone PIR:
Wide Angle Lens (P/N 5-532-439-00)
44 lunga portata
12 intermedie
6 inferiori
4 antistrisciamento
Zonas de detección:
Wide Angle Lens (P/N 5-532-439-00)
44 zonas de largo alcance
12 zonas intermedias
6 zonas de corto alcance
4 zonas de angulo cero
PIR Fields of View:
Wide Angle Lens (P/N 5-532-439-00)
44 long range zones
12 intermediate zones
6 lower zones
4 look-down zones
Pet Immune Lens (P/N 5-532-489-00)
44 long range zones
36 intermediate zones
18 lower zones
4 look-down zones
Pet Immune Lens (P/N 5-532-489-00)
44 faisceaux longs
36 intermediaires
18 courts
4 verticaux
Pet Immune Lens (P/N 5-532-489-00)
44 lang bereik zones
36 midden
18 laag
4 kruipzones
Pet Immune Lens (P/N 5-532-489-00)
44 lang bereik zones
36 midden
18 laag
4 kruipzones
Pet Immune Lens (P/N 5-532-489-00)
44 long range zones
36 intermediate zones
18 lower zones
4 look-down zones
Dimensions: 4.93” x 2.93” x 1.68”
(12.5cm x 7.5cm x 4.3cm)
Dimensions:
12.5cm x 7.5cm x 4.3cm
Dimensioni:
12.5cm x 7.5cm x 4.3cm
Dimensiones:
12.5cm x 7.5cm x 4.3cm
Dimensions: 4.93” x 2.93” x 1.68”
(12.5cm x 7.5cm x 4.3cm)
Weight: 149.0 g (5.26 oz)
Packaged: 205.0 g (7.23 oz)
Masse: 149.0 g
Emballé: 205.0 g
Peso: 149.0 g
Impachettato: 205.0 g
Peso: 149.0 g
Embalaje del producto: 205.0 g
Weight: 149.0 g (5.26 oz)
Packaged: 205.0 g (7.23 oz)
APPROVAL LISTINGS / AGREMENT / OMOLOGAZIONI / HOMOLOGACIONES / APPROVAL LISTINGS
•
FCC part 15, Class B verified
•
IC, RSS-210, Class B verified
•
CE
•
EN 50131-1 and EN 50131-2-4 Security Grade 2, Environment Class II.
•
EN 50131-1 en EN 50131-2-4 Security Grade 2; Environmental Class II.
•
EN 50131-1 et EN 50131-2-4, grade 2, classe enironnementale II.
•
EN 50131-1 e EN 50131-2-4 Grado di Sicurezza 2; Classe Ambientale II.
•
EN50131-1 y EN 50131-2-4 Grado de Seguridad 2, Clase ambiental II.
C-Tick,
cULus Listed,
INCERT,
NOTES DE CONFORMITÉ
•
En référentiel TS 50131-2-4, installation à 2.30 m, choisir la sensibilité haute, et mettre en place la vis
de capot (fournie)..
•
Compatible pour un raccordement à une alimentation régulée EN 60950 Classe II.
IMQ
NOTE DI CONFORMITA’
•
Per installazioni TS 50131-2-4, montare il sensore a 2.3 m, impostare il sensore in alta sicurezza e
bloccare il coperchio con una vite (Inclusa).
•
Per connessioni con alimentatori compatibili EN 60950 Classe II in contesto EU.
•
COMPLIANCE NOTES
•
For EN 50131-2-4 compliant installations, mount sensor at 2.3m (7.5ft), set pulse count to 1, set sensitivity to
High, and install cover screw.
•
Suitable for connection to an EN60950 Class II Limited Power Source in European installations.
UL COMPLIANCE NOTES
•
Product must be tested once each year.
•
Wiring the terminals incorrectly may damage this unit, and/or the equipment wired to it.
NOTAS DE CONFORMIDAD
•
Para instalaciones que cumplen TS50131-2-4: monte el detector a una altura de 2.3m (7’6”),
seleccione alta sensibilidad y coloque el tornillo de la tapa.
•
Adecuado para conectarlo con una fuente de alimentación EN60950 Clase II en instalaciones
Europeas.
COMPLIANCE NOTES
•
For EN 50131-2-4 compliant installations, mount sensor at 2.3m (7.5ft), set pulse count to 1, set
sensitivity to High, and install cover screw.
•
Suitable for connection to an EN60950 Class II Limited Power Source in European installations.
FCC NOTICE:
To obtain applicable EU compliance Declaration of Conformities for this product, please refer to our Website,
http://www.security.honeywell.com/hsce/international/index.html. For any additional information regarding the compliance of this
product to any EU specific requirements, please contact:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
− Reorient or relocate the receiving antenna.
− Increase the separation between the equipment and receiver.
− Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
− Consult the dealer or an experienced radio/television technician for help.
The user is cautioned that changes or modifications not expressly approved by Honeywell could void the user’s authority to
operate this equipment.
Les déclarations de conformité aux normes Européennes de ce produit sont disponibles sur notre site Internet à l’adresse
http://www.security.honeywell.com/hsce/international/index.html. Toutes informations complémentaires relatives à la conformité
de ce produit à des normes Européennes particulières peuvent être obtenues auprès de notre département «Assurance
Qualité»:
Per ottenere una copia della Dichiarazione di conformità CE applicabile di questo prodotto, si prega di fare riferimento al nostro
sito Web, http://www.security.honeywell.com/hsce/international/index.html. Per ogni ulteriore informazione relativa alla
conformità di questo prodotto alle normative specifiche CE, siete pregati di contattare:
Para obtener la conformidad con la normativa EU y declaración de conformidad de este producto, por favor visite nuestra
Website, http://www.security.honeywell.com/hsce/international/index.html. Para cualquier información adicional sobre este
producto u otras especificaciones EU, por favor contacte con:
IC NOTICE:
This Class B digital device complies with RSS-210 of the IC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
To obtain applicable compliance Declaration of Conformities for this product, please refer to our Website,
http://www.security.honeywell.com/hsce/international/index.html. For any additional information regarding the compliance of this
product to any EU specific requirements, please contact:
Cet appareil numérique de la Classe B est conforme à la norme CNR-210 des règles d’IC. L'utilisation de ce dispositif est
autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l'utilisateur du dispositif doit
être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Quality Assurance Department,
Honeywell Security & Custom Electronics,
Newhouse Industrial Estate
Motherwell,
Lanarkshire ML1 5SB,
Scotland, United Kingdom.
Tel: +44(0)1698 738200
Email: UK64Sales@Honeywell.com
 2007 Honeywell International Inc. Honeywell, IntelliSense and DUAL TEC are registered trademarks of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved. Made in China.
For the latest U.S. warranty information, please go to: www.honeywell.com/security/hsc/resources/wa or
Please contact your local authorised Honeywell representative for product warranty information.
Contacter un revendeur Honeywell autorisé pour obtenir des informations sur la garantie de ce produit.
Contatti il suo rappresentante Honeywell per ulteriori informazioni su prodotti e garanzia.
Por favor contacte con su distribuidor Honeywell Security para información sobre la garantía del producto.
Please contact your local authorised Honeywell representative for product warranty information.
P/N P800-01643 Rev A
- Page 4 -

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2008:05:28 13:17:35Z
Modify Date                     : 2008:05:29 11:00:02-07:00
Metadata Date                   : 2008:05:29 11:00:02-07:00
Producer                        : Acrobat Distiller 4.05 for Windows
Format                          : application/pdf
Document ID                     : uuid:7c1b3bc6-5322-401b-9863-2bb30246361e
Instance ID                     : uuid:12012cec-91c4-47c7-a33b-becc98822755
Page Count                      : 4

EXIF Metadata provided by EXIF.tools

Ademco 04007500 Microwave/PIR motion sensor User Manual

Honeywell International Inc. Microwave/PIR motion sensor Users Manual

Users Manual

FCC ID Filing: C2D04007500

Navigation menu

Namespaces

Views

Navigation