Ademco 8DL58111 One Zone Door / Window Transmitter User Manual 800 03928V1 5811 8 11

Honeywell International Inc. One Zone Door / Window Transmitter 800 03928V1 5811 8 11

Users Manual

800-03928V1 8/11 Rev. A ADEMCO 5811 One Zone Door/Window Transmitter Installation Instructions Model 5811 is a single zone Door/Window Transmitter, compatible with alarm systems that support 5800 series wireless devices. 5811 has a unique serial number permanently assigned during manufacture, which must be entered into the control panel upon installation. Refer to the panel’s installation instructions for programming details. NOTE: During programming of the control unit, 5811 transmitters should be treated as “RF” (i.e. supervised RF) Type. MOUNTING Choose a mounting location for 5811 where the device is stationary and the magnet is mounted to the moving part of the door or window. To verify adequate signal strength conduct Go/No Go tests (see control’s instructions) on 5811 before mounting permanently. 1. Install Battery by inserting one edge under one of the two plastic battery retainer clips, then pressing down firmly to snap it beneath both clips; see diagram. 2. Mount 5811 using double-faced tape (supplied) by affixing it to the back of the unit and mounting the unit in place. Use screws (optional) if desired; see diagram. Mount the magnet (supplied) near the alignment marks on the case (see Diagram). REEDLATCHROTATETOCLOSEMAGNETMOUNTINGHOLESMAX GAP3/4"CASE TABS 3. Engage the case tabs (see diagram), then rotate the housing to close. Engage latch with firm pressure to close and lock. BATTERY REMOVAL 1. Open housing by inserting a flat blade screwdriver into latch and twisting gently. 2. Remove old battery cell using a small flat screwdriver blade, as shown in the diagram. SCREWDRIVER(NO)5811-006-V1SCREWDRIVER(CORRECT)SCREWDRIVER(NO)PLACE TIP OF FLAT SCREW DRIVER BETWEEN EDGE OF BATTERY AND PLASTIC CASEAS SHOWN. POSITIONINGSCREWDRIVER AT ANY OTHERCORNER MAY CAUSE DAMAGETO DEVICE. CAREFULLY PRY UP WHILE TWISTING TO REMOVE BATTERY.ABXX
FEDERAL COMMUNICATIONS COMMISSION STATEMENT: The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / IC STATEMENT: This device complies with Part 15 of the FCC Rules, and RSS 210 of Industry Canada (IC). Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable. SPECIFICATIONS Dimensions 2-1/8” (55mm) x 1-3/16” (30mm) x 1/4” (7mm) Operating Conditions 23° F (-5° C) to 120° F (50° C). Relative Humidity 95%, (non-condensing) Replacement Battery Renata/Panasonic CR2032 WARRANTY INFORMATION For the latest warranty information, please visit: www.honeywell.com/security/hsc/resources/ wa REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH WHICH THIS DEVICE IS USED FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. 2 Corporate Center Drive, Suite 100P.O. Box 9040, Melville, NY 11747Copyright © 2011 Honeywell International Inc.www.honeywell.com/security Ê800Ê800Ê800Ê800----03928V1dŠ03928V1dŠ03928V1dŠ03928V1dŠ 800-03928V1 8/11 Rev. A

Navigation menu