Ademco 8DL5882-4 Remote Control Security RX User Manual N7635 3V3 II

Download:
Mirror Download [FCC.gov]
Document ID	260843
Application ID	s/eRzYCZgTaTzUC/t19wCA==
Document Description	ii with FCC information
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.06kB (125781 bits)
Date Submitted	2002-08-02 00:00:00
Date Available	2002-09-17 00:00:00
Creation Date	2001-05-23 08:38:35
Producing Software	Acrobat Distiller 3.02
Document Lastmod	2002-06-26 11:34:10
Document Title	Microsoft Word - N7635-3V3_II.doc
Document Creator	PSCRIPT.DRV Version 4.0

N7635-3V3
1/01
5881EN Series
RF Receiver
INSTALLATION AND SETUP GUIDE
INTERIOR, etc.) and the procedure for programming the
receivers.
These receivers should not be installed in an area subject to
environmental extremes of below freezing (such as an
unheated warehouse) or extremely high temperatures (such
as an attic).
INTRODUCTION
The 5881EN series of RF receivers is designed for use with
control panels that support an RF receiver connection via
the keypad terminals. The receiver recognizes alarm, status,
and keypad control messages from wireless transmitters
operating at 345MHz.
One or two individually identified receivers can be
employed, depending on the control used. Connection of
multiple receivers to a control can provide redundant
coverage or extend coverage in large areas.
These receivers feature a Spatial Diversity System that
virtually eliminates the possibility of "nulls" and "dead
spots" within the coverage area. The 5881EN series of
receivers use ADEMCO’s new Signal-Sentry™ technology,
and can be used in commercial fire installations.
Additionally, the 5881ENHC receiver contains front and
back tamper that permits its use in commercial burglary
installations.
UL
INSTALLATION
With some controls, a receiver may be mounted directly
inside the control's cabinet (receiver circuit board only,
without its plastic housing) instead of remotely (in its own
housing). In both cases, avoid mounting the receiver
antennas against a metal surface.
NOTE: You may only mount the 5881ENHC its own plastic
housing. If you attempt to mount the 5881ENHC in the
control’s cabinet, the receiver constantly reports a tamper
condition.
1. Remove the receiver's cover by inserting and twisting
a screwdriver blade in the slot at the center of the cover's
lower edge.
2. If the receiver is to be mounted within the
control's cabinet (refer to Figure 1):
a. Remove the receiver's circuit board from its base by
bending back the two flexible plastic tabs that hold
the board's lower edge.
b. In the control's cabinet, unfasten and move the
control circuit board downward (if already installed).
c. Hang two mounting clips (provided with the receiver)
on the raised cabinet tabs, as shown in Detail B of
Figure 1.
d. Insert the top of the receiver board between the rows
of slots at the top of the cabinet, as shown in Detail A.
e. Position the base of the receiver board onto the
mounting clips and secure to the cabinet with the
supplied screws. See Detail B.
f. Hang two mounting clips (supplied with the control
board), on the raised cabinet tabs as shown in Detail
C in Figure 1.
g. Insert the top of the control board into the slots of the
mounting clips secured in step e above.
h. Position the lower end of the control board into place
on the mounting clips and secure both to the cabinet
with the two supplied screws.
i. Insert both grounding lugs (supplied with the
receiver) through the top of the cabinet into the lefthand terminals of the antenna blocks (located on the
upper edge of the receiver board), and secure them to
the cabinet with the screws provided, as shown in
Detail D.
• In commercial fire applications, the receiver can
only be used with control panels that are approved
for use in Commercial Fire Installations. When the
5881EN is used in commercial fire applications,
DIP switch 5 must be in the ON position.
commercial
burglary
applications,
the
• In
5881ENHC can only be used with control panels
that are approved for use in Commercial Burglary
Installations.
• In commercial fire applications, a keypad must be
connected to Keypad Port 2 in the control. The
keypad must be mounted on the control or within 3
feet of the control with the wiring encased in
conduit.
Each receiver supports the number of zones shown below.
5881ENL
Up to 8 zones
5881ENM
Up to 16 zones
5881ENH
*See below
5881ENHC
*See below
* The number of zones that the 5881ENH
receiver can support depends on the
control with which it is used. See the
control panel’s instructions for specific
details.
If a receiver is connected to a system in which more than
the permitted number of wireless zones have been
programmed, a "SET UP ERROR" message (on alpha
keypads) or an "E4 or “E8”" message (on fixed-word
keypads) will be displayed on the system's keypad, and none
of the zones will be protected.
The instruction manual that accompanies the control
includes
recommendations regarding
receiver
and
transmitter locations, the types of wireless zones that can
be programmed (e.g., ENTRY/EXIT, PERIMETER,
HOLES FOR ANTENNAS
AND GROUNDING LUGS
CABINET
CIRCUIT BOARD
BOARD
SUPPORTING
SLOTS
RECEIVER CIRCUIT BOARD
(See Detail D)
DETAIL A
SIDE VIEW
OF BOARD
SUPPORTING SLOTS
MOUNTING
CLIP
CONTROL
CIRCUIT
BOARD
MOUNTING
CLIP
SCREW
(2)
ANTENNA
(2)
GROUNDING
LUG
(2)
DETAIL B
SIDE VIEW
OF MOUNTING
CLIP
CABINET
DETAIL C
SIDE VIEW
OF MOUNTING
CLIP
RCVR BRD
ANTENNA
MOUNT
(2 PLACES)
DETAIL D
ANTENNA AND GROUNDING LUG INSTALLATION
pcb_RF_mount-V0
Figure 1: Installing the Receiver Board in the Control’s Cabinet
d. Affix the receiver's Summary of Connections label to
the inside of the housing cover.
j. Insert the receiver’s antennas through the top of the
cabinet, into the blocks’ right-hand terminals, and
tighten the screws.
k. Affix the receiver's Summary of Connections label to
the inside of the control's cabinet door.
l. Discard the receiver's unused plastic cover and base.
3. If the receiver is to be located remotely from the
control in its own plastic enclosure (not in a cabinet):
You will not need the circuit board mounting clips,
grounding lugs and screws included with the receiver.
a. If concealed wiring is to be used, route it through the
rectangular opening at the rear of the base before
mounting. For surface wiring entry, a thin breakaway
area is provided along the base's right edge.
b. Mount the receiver in the selected location. For
greatest security, use all four mounting holes (two
keyslot holes and two round holes) provided in the
plastic base.
c. If installing a 5881ENHC, install a flat-head screw
(supplied) in the case tamper tab as shown in Figure
2. When the receiver is pried from the wall, the
tamper tab will break off and remain on the wall.
This will activate a tamper switch in the receiver and
cause generation of a tamper signal. Note that this
signal will also be generated when the receiver’s front
cover is removed.
SCREW
5881ENHC-001-V0
Figure 2: Tamper Protection
4. Setting the DIP switches (All Receivers):
a. Set the receiver's DIP switch (#2 through #4) to
identify the receiver's address (refer to the DIP switch
chart in Figure 3).
b. Verify that DIP switch #1 is in the OFF position.
c. Set DIP switch #5 according to the following chart.
8. Replace the receiver's cover.
DIP SWITCH #5
For . . .
Commercial Fire Applications
Non-commercial Fire Applications
ENCRYPTED KEYS
The receiver can support up to 16 encrypted wireless
transmitters (keys) at one time. If the number on the
receiver microprocessor is WAK 4406-4 or higher, the
receiver provides you with the capability to check space
available and/or delete encrypted keys using the procedures
below.
The GREEN LED located on the receiver's circuit board
may be used to determine how many more encrypted keys
may be enrolled into the receiver. This LED is also used to
indicate when encrypted keys may be deleted. To determine
how many more encrypted keys may be enrolled and/or to
delete enrolled encrypted keys:
1. Remove power from the receiver and set DIP
switch 1 to the ON position.
2. Apply power to the receiver and watch the GREEN
LED. You will see one of the following indications:
a. The GREEN LED blinks the number of spaces that
are free for additional encrypted key enrollment and
then goes to constantly ON.
b. The GREEN LED is constantly ON, indicating the
receiver is full.
c. The GREEN LED is OFF, indicating no encrypted
keys are enrolled.
3. If you do not want to delete any enrolled
encrypted keys, advance to step 4. If you want to
delete enrolled encrypted keys, wait until the
GREEN LED is constantly ON in step 2 a. or 2 b.
above and then:
a. Record the positions of DIP switches 1 through
5.
b. Set DIP switches 1 through 5 to the opposite
positions of their current settings and wait a
few moments.
c. Set DIP switches 1 through 5 back to their
original positions as recorded in step a. All
enrolled encrypted keys will be deleted.
4. Place DIP switch 1 back into the OFF position to
return to normal receiver operation.
Set to . . .
ON
OFF
NOTES:
• If multiple receivers are used on one control, DIP
switch #5 must be set to the same position on all
receivers.
• DIP switch #5 reduces sensitivity during
supervision message reception. For commercial fire
applications, DIP switch #5 must be in the ON
position.
5. Insert the wiring plug (with 4 flying leads) into the
mating socket on the receiver (see Figure 3 for socket
location). Connect the 4 wires to the control's
corresponding keypad terminals (see “Interface Wiring”
in the SPECIFICATIONS section).
6. Install the antennas in the right-hand terminals of the
two terminal blocks at the upper edge of the circuit
board, one into each block’s right-hand terminal, and
tighten the screws to secure them.
Caution: Avoid mounting the receiver antennas against
a metal surface.
7. Proceed with any programming of the control that
may be necessary for RF operation, and the
installation of the system's wireless transmitters,
as described in the control's installation and setup guide
and the transmitter's installation instructions.
NOTES:
• The receiver can support up to 16 encrypted wireless
transmitters (keys). The total quantity of wireless
keys (encrypted and unencrypted) that can be used is
determined by the control panel.
• Wireless key buttons must be enrolled to zones in the
control panel via zone programming first. If the
wireless key is to be used for arming and disarming
the VISTA-40 and up, a user number must then be
assigned to the wireless key via user programming. If
it is not done in this order, you will be unable to
respond successfully to the RF button zone number
prompt in user programming.
• If more than one receiver is being used and you are
using encrypted wireless keys, we recommend that
you (a) enter the GO/NO GO mode, (b) disconnect one
receiver, (c) enroll all encrypted keys into the
connected receiver, (d) reconnect the disconnected
receiver, (e) exit the GO/NO GO mode, and then (f)
repeat (a) through (e) for the receiver that was
disconnected.
• The RED LED located on the receiver's circuit board
should be used as an indicator of strong local radio
frequency interference. If this LED is continuously
illuminated, the receiver should be relocated.
• After a successful enrollment of an encrypted key, the
GREEN LED blinks the number of spaces that are
free for additional encrypted key enrollment.
SPECIFICATIONS
Interface Wiring:
RED
12VDC input (+) Aux. Power
GREEN:
Data Out to Control
YELLOW: Data In from Control
BLACK:
Ground (–)
Dimensions:
7-3/8" W x 4-3/8" (10-7/8” w/antennas) H x 1-7/16" D
188mm W x 112mm H (277mm w/antennas) x 37mm D
Input Voltage:
12VDC (from control’s keypad terminals)
Range:
200ft (60m) nominal indoors from wireless transmitters
(the actual range to be determined with the security
system in the Test mode).
Current:
60mA (typical)
Operating Temperature:
0-50°C
TO THE INSTALLER
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the
user are vital to continuous satisfactory operation of any alarm system.
The installer should assume the responsibility of developing and offering a regular maintenance
program to the user, as well as acquainting the user with the proper operation and limitations of the
alarm system and its component parts. Recommendations must be included for a specific program
of frequent testing (at least weekly) to insure the system's operation at all times.
Figure 3: Summary of Connections, 5881EN Series RF Receivers
5881ENHC
5881ENH
5881ENM
5881ENL
5881EN SERIES
TO RELEASE CIRCUIT BOARD, BEND BACK
BOTTOM TABS (2). FOR COMMERCIAL FIRE
APPLICATION. USE TWO SCREWS
(NOT SUPPLIED) WITH INSULATING WASHERS
BENEATH THE HEADS. TO MOUNT BOARD IN
SEPARATE CABINET.
(SEE RECEIVER'S INSTRUCTIONS).
NOTE: WHEN CIRCUIT BOARD IS MOUNTED
IN CONTROL'S CABINET, GROUNDING LUGS
(2) PROVIDED MUST BE INSERTED IN LEFTHAND TERMINALS OF ANTENNA BLOCKS
AND SECURED TO CABINET (SEE RECEIVER'S
AND CONTROL'S INSTRUCTIONS).
WHEN BOARD IS MOUNTED IN A SEPARATE
CABINET (COMMERCIAL FIRE APPLICATION),
DO NOT USE THE GROUNDING LUGS.
MOUNTING
HOLES
DIP SWITCH
ANTENNAS
INSERT IN
RIGHT-HAND
TERMINALS
INTERFERENCE
GREEN LED: NORMALLY OFF
INDICATOR LED
ONE SHORT FLASH - RF MESSAGE DECODED
ONE LONGER FLASH - COMMAND RECEIVED FROM CONTROL
NOTES:
WHEN AN ENCRYPTED TRANSMITTER IS SUCCESSFULLY ENROLLED,
LED FLASHES A NUMBER OF TIMES THAT IS EQUAL TO THE SPACE
AVAILABLE FOR ADDITIONAL ENCRYPTED KEYS.
THE GREEN LED IS ALSO USED WHEN CHECKING ENCRYPTED KEY
SPACE AVAILABLE AND PERFORMING DELETIONS. SEE ENCRYPTED
KEYS DESCRIPTION FOR DETAILS.
CIRCUIT
BOARD
SEE
DETAIL A
GREEN
BLACK
RED
YELLOW
DETAIL A
FRONT AND
REAR TAMPER
5881ENHC ONLY
BACK OF PC BOARD
FRONT OF PC BOARD
PLUG & SOCKET
WIRING
OPENING
TO CONTROL'S KEYPAD
TERMINALS. EACH RECEIVER
MUST BE ON INDIVIDUAL
HOME RUN.
USE MAX. OF 220 ft. (67m) OF #22 (0.64mm) WIRE
OR 550 ft. (168m) OF #18 (1mm) WIRE FOR EACH RUN.
20 ft. MAX. IN COMMERCIAL FIRE INSTALLATIONS.
(SEE RECEIVER'S INSTRUCTIONS).
ON
OFF
—
—
—
SWITCH
POSITION
ON —
—
—
—
ON
—
ON
ON ON
ON ON ON ON
ON ON —
—
(SEE TEXT ABOVE)
5881EN-SOC-V1
MUST BE IN OFF POSITION
—
—
ON
RECEIVER ADDRESS SETTINGS
(“—” means “OFF”)
DIP SWITCH BELOW SHOWN SET FOR ADDRESS "0".
CONSULT CONTROL'S INSTRUCTIONS FOR ADDRESS TO USE.
DIP SWITCH: WHITE AREAS = SWITCH HANDLES
POSITION 2-4: DETERMINE RECEIVER'S ADDRESS
DIP SWITCH #5
ON:
FOR USE IN COMMERCIAL FIRE APPLICATIONS.
(SEE THE RECEIVER'S INSTRUCTIONS).
OFF:
USE IN NON-COMMERCIAL FIRE INSTALLATIONS.
FCC ID CFS8DL5882A
CANADA:17481021751A
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your
information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's
instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B
computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may find
the following booklet prepared by the Federal Communications Commission helpful:
"Interference Handbook"
This booklet is available under Stock No. 004-000-00450-7 from the U.S. Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation and Setup Guide or User Guide.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
WARNING
THE LIMITATIONS OF THIS WIRELESS ALARM SYSTEM
While this System is an advanced wireless security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm
system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm
warning device.
• Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated
devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if
their AC power supply is cut off for any reason, however briefly.
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been
recently checked during a weekly test, blockage can occur if a metal object is moved into the path.
• A user may not be able to reach a panic or emergency button quickly enough.
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning
for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the
reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and
positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the
other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for
example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of
fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent
explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending
on the nature of the fire and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to
allow all occupants to escape in time to prevent injury or death.
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared
Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed
areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions,
glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical
system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the
protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection performance can decrease.
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly
open doors. If warning devices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people
inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or
other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people.
• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service.
Telephone lines are also subject to compromise by sophisticated intruders.
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency
situation. In the case of a monitored alarm system, authorities may not respond appropriately.
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 20 years, the
electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be
tested weekly to make sure all sensors and transmitters are working properly. The security console (and remote keypad) should be tested as well.
This system's wireless transmitters are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much
as 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low
temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can
identify a true low battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system.
Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners,
property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these
developments.
ADEMCO LIMITED WARRANTY
Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates
("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans
and specifications and to be free from defects in materials and workmanship under normal use and service for 24
months from the date stamp control on the product or, for products not having an ADEMCO date stamp, for 12 months
from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the
shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for
materials or labor, any product which is proved not in compliance with Seller's specifications or proves defective in
materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or
otherwise if the product is altered or improperly repaired or serviced by anyone other than ADEMCO factory service.
For warranty service, return product transportation prepaid, to ADEMCO Factory Service, 165 Eileen Way, Syosset,
New York 11791.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER
BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN
NEGLIGENCE OR FAULT.
Seller does not represent that the products it sells may not be compromised or circumvented; that the products will
prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases
provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may only
reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or
a guarantee that such will not occur or that there will be no personal injury or property loss as a result.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR
OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD
LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED
WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL
NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE
AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only
warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited
Warranty is authorized.
165 Eileen Way, Syosset, New York 11791
Copyright © 2001 PITTWAY CORPORATION
¬19l
N7635-3V3
1/01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2001:05:23 08:38:35
Producer                        : Acrobat Distiller 3.02
Creator                         : PSCRIPT.DRV Version 4.0
Title                           : Microsoft Word - N7635-3V3_II.doc
Modify Date                     : 2002:06:26 11:34:10-04:00
Page Count                      : 8

EXIF Metadata provided by EXIF.tools