Ademco 8DL5883-2 remote security transceiver User Manual K3791 iibx

Honeywell International Inc. remote security transceiver K3791 iibx

ii with FCC statment

K3791 (bx) 6/6/01®,167$//$7,21$1'6(783*8,'(INTRODUCTIONThe 5883 series RF Transceiver Module contains an RF receiver and atransmitter. It is intended for use with ADEMCO’s 5800 series RFtransmitters, including bi-directional wireless units (e.g. 5827BD,5804BD), and the 5800RL Wireless Relay Module (see Fig. 1).The 5883 receives alarm, status, and control messages from 5800transmitters, and passes these messages to the control panel viawired connections. The control then responds accordingly (arm/disarmthe system, initiate an alarm, etc.). The 5883 also transmits systemstatus and other conditions to 5804BD or 5827BD bi-directional units(if used). The 5883 can emulate the functions of a 5800TM module,and can control the relays on the 5800RL Wireless Relay Module.The 5883 features a Spatial Diversity system that virtually eliminatesthe possibility of "Nulls" and "Dead Spots" within the coverage area. Italso incorporates ADEMCO’s new high-security encryption technology(UL-864 and RF Jam Detect).If more than the permitted number of wireless zones are programmed,a "SET UP ERROR" message (on alpha keypads) or an "E4 or “E8”"message (on fixed-word keypads) will be displayed on the system'skeypad, and none of the zones will be protected.The 5883 models support the number of zones shown below.5883M Up to 16 zones5883H Depends on the control with which it is used. Seethe control panel’s instructions for specificdetails.5883TRANSCEIVERCONTROLPANEL*5800 SERIES WIRELESS TRANSMITTERS*CONTROL MUST BE CAPABLE OFSUPPORTING A 5800 RF SYSTEM2-WAYWIRELESS KEYPAD(e.g., 5827BD, 5804BD)OR5800RL 2-WAY RELAYMODULEKEYPAD TERMINALS ON CONTROLBOARD2-WAYTRANSMISSIONDATA IN TOCONTROLDATA OUTTO 5883Figure 1. Block DiagramMOUNT THE MODULE OR PC BOARDThe 5883 can be mounted remotely, or, with some controls, can be mounted inside the control's cabinet. When mounting, make sure theantennas do not touch any metal surfaces.First, Check for RF Interference: Before mounting permanently,use the red RF Interference LED (see figure 3) to check for stronglocal radio frequency interference at the intended mounting location.If this LED is continuously lit, the 5883 module should be relocated.Removing the CoverRemove the 5883's cover by inserting and twisting a screwdriver bladein the slot at the center of the cover's lower edge.Replace the cover when installation is complete if unit is notmounted within a cabinet.Mounting inside the control's cabinet (refer to Fig. 2):1. Remove the 5883’s circuit board from its base by bending back thetwo flexible plastic tabs that hold the board's lower edge. Discardthe 5883's unused plastic cover and base.2. In the control's cabinet, unfasten and move the control circuit boarddownward (if already installed).3. Hang two short (black) mounting clips (provided) on the raisedcabinet tabs in the cabinet, as shown in Detail B of Figure 2.4. Insert the top of the 5883’s board into the supporting slots at thetop of the cabinet (Detail A). Swing the bottom of the board into thetwo short (black) mounting clips installed in step 3, and secure it tothe cabinet with the accompanying screws. See Detail B.5. Insert the top of the control’s board into the slot in the black clipsholding the lower edge of the 5883 board (see Detail B); position twolong (red) clips at the lower edge of the board (see Detail C).6. Swing the lower edge of the control board into place, and securewith two additional screws.7. Insert the grounding lugs (provided) through the top of the cabinetand into the left-hand terminals of the antenna blocks (at theupper edge of the 5883's circuit board). Secure it to the cabinet withthe two screws provided. See Detail D.8. Insert the 5883’s two antennas through the two openings in thetop of the cabinet, one into each block’s right-hand terminal, andtighten the screws to secure them.9. Affix the 5883's Summary of Connections label to the inside of thecontrol's cabinet door.Mounting the 5883 remotelyNOTE: If mounting the 5883 in its own enclosure, the supplied PCBmounting clips, grounding lugs, and screws are not needed.1. For concealed wiring, route wires through the rectangular openingat the rear of the base before mounting. For surface wiring entry,a thin breakaway area is provided along the base's right edge.2. Mount the module in the selected location. For greatest security,use all four mounting holes (two keyslot holes and two roundholes) in the plastic base.3. Install each antenna in the respective right-hand terminal of thetwo terminal blocks at the upper edge of the 5883’s circuit board,and tighten the screws to secure them.4. Affix the 5883's Summary of Connections label to the inside of thehousing cover.MOUNTINGCLIPCABINETDETAIL DANTENNA AND GROUNDING LUG INSTALLATIONANTENNAMOUNT(2 PLACES)ANTENNA(2)SCREW(2)MOUNTINGCLIPCONTROLCIRCUITBOARDBOARDSUPPORTINGSLOTSHOLES FOR ANTENNASAND GROUNDING LUGSRECEIVER CIRCUIT BOARD(See Detail D)++++RCVR BRDDETAIL ASIDE VIEWOF BOARD SUPPORTING SLOTSDETAIL BSIDE VIEWOF MOUNTINGCLIPDETAIL CSIDE VIEWOF MOUNTINGCLIPGROUNDINGLUG(2)pcb_RF_mount-V0CIRCUIT BOARDCABINETFigure 2. Installing the 5883 Board in the Control’s Cabinet(Check the control’s Installation Instructions for applicability)GO TO PAGE 3 FOR THEFCC PART 15 STATMENTAND FCC ID NUMBERAND THE IC ID NUMBER
– 2 –Mounting for Commercial Fire Applications (in separate cabinet)For Commercial Fire applications, the 5883 module must be mountedin a separate cabinet (N4868V4–BE), using the ADEMCO Cam Lock(N6277), and Retainer Clip (N6277–1). Refer to the control’sinstructions for installing the Cam Lock and Retainer Clip.The cabinet containing the module must be located no more than 20 feetfrom the alarm control cabinet (maximum wire run length 20 feet), withno intervening walls or barriers.1. Remove the PC board by bending back the two flexible plastic tabsthat hold the board's lower edge. Discard the 5883’s unused plasticcover and base.2. Insert the top of the board into the supporting slots at the top ofthe cabinet (see Detail A, Figure 2).Secure the bottom of the board with the 2 screws removed in step1 above, using an insulating washer (supplied) between the head ofeach mounting screw and the PC board.3. Affix the 5883's Summary of Connections label to the inside of thecabinet door.IMPORTANT: If mounting the 5883 in a separate cabinet in aCommercial Fire installation, do not use the antenna grounding lugs.SET THE DIP SWITCHESUse the DIP switches to set the 5883’s device address, to activateCommercial Fire usage (if applicable), to enable the built-intransmitter, and to check or delete encrypted keys.Addresses: The 5883 Transceiver has two device addresses: one forthe receiver (addresses 1-7) and one for the transmitter (addresses27-30, similar to the 5800TM device addresses; see notes 5 and 6below)). First, select a pair of addresses from the table below,making sure that neither address is currently being used in thealarm system, then use DIP switches 2-4 to set the address pair. Theaddresses should then be programmed in the control. Do not programthe transmitter’s address in the control if the 5883 is not being usedwith 5800TM compatible devices, such as the 5804BD or 5827BDDIP Switch FunctionsSw. Function1 Check/deactivate high-security keys (see High-Security Keys paragraph)Device Address SettingsTransmitter: 28 29 30 27 28 29 30Receiver: Non-Addr. 123456 72 OFF OFF OFF OFF ON ON ON ON3 OFF OFF ON ON OFF OFF ON ON4 OFF ON OFF ON OFF ON OFF ON5Commercial/Non-commercial Fire Installation:ON = commercial fire system (see Notes for Commercial Fire Apps.)OFF = non-commercial fire system6 ON = enable transmitter (if using 5800TM compatible devices)NOTE: If using more than one 5883 in a system, enable thetransmitter in only one 5883.OFF = disable transmitter7 Not used; leave in OFF position8 Used when removing RF keypads (see Removing RF Keypadsparagraph); otherwise leave OFFNOTES:•If multiple 5883 Transceivers are used on one control, DIP switch5 must be set to the same position on all receivers.•DIP switch 5 reduces sensitivity during supervision messagereception. For Commercial Fire applications (see note box), youmust set DIP switch 5 to the ON position.•DIP switches 2–4 select both an RF receiver and an RFtransmitter device address.•When used with 5800TM compatible devices such as the 5800RL,5804BD, or the 5827BD, the selected transmitter device addressmust be enabled as a “keypad” in the control and DIP switch 6must be set to “ON.”•If the 5883 is not being used with 5800TM compatible devices,such as the 5804BD or 5827BD, the RF transmitter address shouldbe ignored and DIP switch 6 should be set to OFF.•If programming the control to supervise the 5883, program onlythe receiver address for supervision. Do not program thetransmitter address for supervision.Notes for Commercial Fire Applications:•DIP switch 5 must be in the ON position.•All other system components, including the control, must beapproved for use in Commercial Fire applications.•When the 5883 is not used in a Commercial Fire application,switch 5 must be placed in the OFF position.CONNECT THE WIRING FROM THE CONTROL1. Insert the wiring plug (with 4 flying leads) into the mating socketon the 5883 (see Figure 3 for socket location).2. Connect the 4 wires to the control's corresponding remote keypadconnection points as follows:RED 12VDC input (+) Aux PowerGREEN: Data to Control (control’s data IN)YELLOW: Data from Control (control’s data OUT)BLACK: Ground (–)LED FUNCTIONS (refer to Figure 3)Red RF Interference LED: Lit Indicates local RF interference.Green LED: Flickering indicates reception of messages (decodedand/or non-decoded).Yellow LED: Occasional blinks occur under normal operation.Red LED: Blinks indicate available space for high security keys;Steady ON indicates ready to deactivate high securitykeys or remove wireless (RF) keypads.See High Security Keys and Wireless Keypadssection below for more information.RF INTERFERENCERED INDICATORREDYELGRNDIP SWITCHONOFF 234567815883 CIRCUIT BOARDMOUNTINGHOLES(4)ANTENNAS(INSERT INRIGHT-HANDTERMINALS)YELLOWREDBLACKGREENWIRINGOPENINGKNOCKOUT AREAFOR SURFACE WIRINGTOCONTROL'SREMOTEKEYPADCONNECTIONPOINTSTO RELEASE CIRCUIT BOARD,BEND BACK TABS SOCKETPLUG5883-002-V0Figure 3. 5883 Transceiver
– 3 –PROGRAM THE CONTROL FOR RF OPERATIONProceed with any control panel programming that may be necessary for RF operation and the installation of the system's wireless transmitters,as described in the control's installation instructions. In addition, note the following:•Enable the appropriate control data field for RF usage.•Enroll the wireless keypad address(es), if used (see instructionsprovided with keypad).•Wireless key buttons must first be enrolled in the control panel viazone programming, and, where applicable, assigned to a usernumber. Enroll each wireless key in the 5883 by pressing theappropriate buttons according to the instructions provided withthe key.•Upon the successful enrollment of an encrypted key, the red LEDblinks the number of available spaces remaining for additionalencrypted key enrollment (see Checking Available Space For HighSecurity Keys paragraph).•If more than one receiver is being used and you are usingencrypted wireless keys, we recommend that you:a. Enter the GO/NO GO mode.b. Disconnect one receiver.c. Enroll all encrypted keys into the connected receiver.d. Reconnect the disconnected receiver.e. Exit the GO/NO GO mode.f. Repeat steps a-e for the receiver that was disconnected.HIGH SECURITY KEYS & WIRELESS KEYPADSDepending on the control panel used, the 5883 can support up to 16 high-security (encrypted) wireless keys and up to 16 wireless keypads (e.g.,5839). The following paragraphs describe how to:• Check available space for high-security keys• How to deactivate all keys• How to remove all wireless keypads.See the Control’s instructions and the appropriate device instructions for procedures on enrolling high security keys and wireless keypads.Checking Available Space for High Security KeysThe RED LED (above the DIP switch) shows (by blinking) how manyhigh-security keys may be enrolled into the transceiver.1. Remove power from the transceiver and set DIP switches:DIP 1 = ONDIP 8 = OFF2. Apply power and observe one of the following RED LED indications:a. Blinks, indicating the number of available spaces for additionalhigh-security key enrollment, and then lights steady ON.b. Immediate Steady ON (no blinks), indicating that high-security key enrollment is full.c. Off, indicating that no encrypted keys are enrolled.3. Set DIP switch 1 back to the OFF position to return to normalreceiver operation (leave DIP 8 in OFF position).Deactivating High-Security keysThis procedure deactivates all enrolled high-security keys and isrequired only if previously enrolled high-security keys are beingreplaced and there is not enough available space left for them in thereceiver. Once this procedure is performed, all desired high-securitykeys must be re-enrolled to activate high-security operation.1. Perform steps 1 and 2 in Checking Available Space procedureabove.2. Wait until the RED LED lights steady ON then:a. Record the positions of DIP switches 1 through 8.b. Set DIP switches 1 through 8 to the opposite positions of theircurrent settings and wait a few moments.c. Set DIP switches 1 through 8 back to their original positions asrecorded in step a. All enrolled high-security keys will bedeactivated.3. Set DIP switch 1 back to the OFF position to return to normalreceiver operation (leave DIP 8 in OFF position).Removing All Wireless KeypadsThis procedure removes all wireless keypad from the transceiver.1. Remove power from the transceiver and set DIP switches:DIP 1 = OFFDIP 8 = ON2. Apply power and observe the RED LED lights steady ON, then:a. Record the positions of DIP switches 1 through 8.b. Set DIP switches 1 through 8 to the opposite positions of theircurrent settings and wait a few moments.c. Set DIP switches 1 through 8 back to their original positions asrecorded in step a. All enrolled wireless keypads will beremoved from the transceiver.3. Set DIP switch 8 back to the OFF position to return to normalreceiver operation (leave DIP 1 in OFF position).NOTE: If unsure that correct RF keypad (5839) addresses areenabled in the receiver, you should perform the RF keypad deleteprocedure, then enable RF keypad addresses as described in theinstructions included with the RF keypad. Otherwise, erroneous ecpdevice “check” messages may occur.FCC ID: CFS8DL5883-2This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept anyinterference received, including interference that may causeundesired operation. IC: 573F-58832This Class B digital apparatus complies with Canadian ICES-003.Cet Appareil numérique de la classe B est conforme à la normeNMB-003 du Canada.SPECIFICATIONSDimensions:7-3/8" W x 4-3/8" (10-7/8” w/antennas) H x 1-7/16" D188mm W x 112mm H (277mm w/antennas) x 37mm DInput Voltage: 12VDC (from control’s remote keypad terminals)Current: 80mA typicalRange: 200ft (60m) nominal indoors from wireless devices (actualrange is determined with the control in TEST mode)TO THE INSTALLERRegular maintenance and inspection (at least annually) by theinstaller and frequent testing by the user are vital to continuoussatisfactory operation of any alarm system.The installer should assume the responsibility of developing andoffering a regular maintenance program to the user, as well asacquainting the user with the proper operation and limitations ofthe alarm system and its component parts. Recommendationsmust be included for a specific program of frequent testing (atleast weekly) to insure the system's operation at all times.
WARNINGTHE LIMITATIONS OF THIS WIRELESS ALARM SYSTEMWhile this System is an advanced wireless security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whethercommercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device.• Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not workwithout batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason,however briefly.• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during aweekly test, blockage can occur if a metal object is moved into the path.• A user may not be able to reach a panic or emergency button quickly enough.• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasonsin as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction withthis System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smokecannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of aresidence or building. A second floor detector, for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke detectorcan sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violentexplosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fireand/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to preventinjury or death.• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not providevolumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannotdetect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting orspraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes intemperature; however, as the ambient temperature of the protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection performance candecrease.• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warningdevices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who areawake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices,however loud, may not warn hearing-impaired people.• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are alsosubject to compromise by sophisticated intruders.• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the caseof a monitored alarm system, authorities may not respond appropriately.• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic componentscould fail at any time.The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to makesure all sensors and transmitters are working properly. The security console (and remote keypad) should be tested as well.This system's wireless transmitters are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 7 years, depending onthe environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, mayall reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of batteryto maintain protection for that given point within the system.Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners andrenters should continue to act prudently in protecting themselves and continue to insure their lives and property.We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.LIMITED WARRANTYAlarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way,Syosset, New York 11791, warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials andworkmanship under normal use and service for 24 months from the date stamp control on the product or, for products not having an Ademco datestamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorterperiod shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which isproved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall haveno obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factoryservice. For warranty service, return product transportation prepaid, to ADEMCO Factory Service, 170 Michael Drive, Syosset, New York 11791.THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OROTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONEFOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, ORUPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCEOR FAULT.Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury orproperty loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection. Customer understandsthat a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm,but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY,SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THEPRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS ORDAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUMLIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE ANDEXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on this product. Noincrease or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.165 Eileen Way, Syosset, New York 11791Copyright © 2001 PITTWAY CORPORATION¬.lK3791 5/01

Navigation menu