Ademco 8DL6HEAT Rate-Of-Rise Heat Detector User Manual
Honeywell International Inc. Rate-Of-Rise Heat Detector Users Manual
a href="https://usermanual.wiki/Ademco" itemprop="url">
Ademco >
Contents
- 1. Users Manual
- 2. Installation Guide
Users Manual

![2 Enrolling / Enrôlement For Lyric Controller 1. Set the Lyric Controller in Programming Mode and select SiX Programming: Security > Tools > [installer code] > Program > (scroll down) > SiX Programming Follow the controller’s instructions. 2. Pull the battery tab to activate the SiXHEAT and begin the enrollment process. 3. The LED flashes (up to about 20 seconds*) during enrollment. • The device sends its unique MAC ID (Serial Number) and Services type to the controller. • The controller registers the device and displays the sensor data on screen. *NOTE: Enrollment time varies depending on the signal strength between the device and the controller. When done, the LED is ON for 3 seconds and the control beeps to confirm enrollment. 4. Select the device and press EDIT. Assign the Zone Descriptor and set the Device Type (SMOKE). Verify the Service and Response Type and set the other options as desired. 5. To complete enrollment, select SAVE. The device can also be manually enrolled by entering the MAC ID (serial number) at the prompt. See the Controller’s Programming Guide for details. Follow instructions in the Controller’s programming guide to program the SiXHEAT zone attributes. For Lyric Gateway Use AlarmNet 360™ to enroll and program this sensor. NOTE: Once enrolled in a system, the SiXHEAT cannot be used with another controller until it is removed from the current controller. See the Controller’s instructions for details. Pour Lyric Controller 1. Réglez Lyric Controller en mode de programmation et sélectionnez SiX Programming: Sécurité > Outils > [code installateeur] > Program > (défiler vers le bas) > Programmation SiX Pour commencer l'enrôlement, suivez les instructions du panneau de commande. 2. Retirez la languette qui recouvre la pile pour activer le SiXHEAT et commencer la procédure d'enrôlement. (Ou, si la languette est déjà retirée, utilisez l'aimant.) 3. Durant l'enrôlement, la DEL clignote (jusqu'à 20 secondes*). • Le dispositif transmet au panneau de commande son ID MAC (numéro de série) et l'information pour les services. • Le panneau de commande enregistre le dispositif et affiche les données du transmetteur sur l'écran. *NOTE : La durée de l'enrôlement varie selon la puissance du signal entre le dispositif et le panneau de commande. 4. Une fois terminé, la DEL demeure allumée durant 3 secondes et le panneau de commande émet 3 bips pour confirmer l'enrôlement. 5. Sélectionnez la zone et appuyez sur EDIT. Attribuez le descripteur de zone et définissez le type de périphérique (porte ou fenêtre). Vérifiez le type de service et de réponse et définissez les autres options selon vos besoins. 6. Déclenchez de nouveau le dispositif pour mettre fin à l'enrôlement et sélectionnez Enregistrer garder. Le dispositif peut également être enrôlé manuellement. Pour les détails, reportez-vous au Guide de programmation du panneau de commande. Suivez les instructions du Guide de programmation du panneau de commande pour programmer les SiXHEAT. Pour Lyric Gateway Enrôlez et programmez le système au moyen d’AlarmNet 360MC. NOTE : Une fois enrôlé, le SiXHEAT ne peut pas être utilisé avec un autre système avant d'avoir été supprimé du panneau actuel. Reportez-vous aux instructions du panneau.](https://usermanual.wiki/Ademco/8DL6HEAT.Users-Manual/User-Guide-3697120-Page-2.png)