Ademco 8DLLYNXTOUCH1 Wireless Control / Communicator User Manual 800 06834 ii

Download:
Mirror Download [FCC.gov]
Document ID	1430257
Application ID	J+Dp2j4+nAf5ydHkJwQUiA==
Document Description	Installers Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	171.83kB (2147859 bits)
Date Submitted	2011-03-11 00:00:00
Date Available	2011-09-07 00:00:00
Creation Date	2011-03-08 16:29:04
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2011-03-10 09:16:16
Document Title	Microsoft Word - 800-06834_ii.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	E652388

PLEASE USE BOOKMARKS
TO GO TO VARIOUS
AGENCY STATEMENTS
LYNX Touch Series
Security Systems
Installation and Setup Guide
ARMED
800-06834 1/11 Rev. A
READY
LYNX Touch Installation and Setup Guide
RECOMMENDATIONS FOR PROPER PROTECTION
The Following Recommendations for the Location of Fire and Burglary Detection Devices Help
Provide Proper Coverage for the Protected Premises.
Recommendations for Smoke and Heat Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's (NFPA) Standard #72
noted below.
• Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and
areas of the household as follows: For minimum protection a smoke detector should be installed outside of each
separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The
installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally
recommended.
• For additional protection the NFPA recommends that you install heat or smoke detectors in the living room,
dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and
attached garages.
In addition, we recommend the following:
• Install a smoke detector inside every bedroom where a smoker sleeps.
• Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely
closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the
sleeper if the door is closed.
• Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air
conditioners or humidifiers) are used.
• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.
• Install smoke detectors in any room where an alarm control is located, or in any room where alarm control
connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could
prevent the control from reporting a fire or an intrusion.
THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE
SOUNDING OF FIRE NOTIFICATION APPLIANCES.
KITCHEN
DINING
BEDROOM BEDROOM
TV ROOM
KITCHEN
DINING
BDRM
LIVING ROOM
BDRM
BEDROOM
BEDROOM
LIVING ROOM
Smoke Detectors for Minimum Protection
Smoke Detectors for Additional Protection
Heat-Activated Detectors
BEDROOM
BEDROOM
TO
BR
BEDROOM
KTCHN
LVNG RM
CLOSED
DOOR
GARAGE
BASEMENT
floor_plan-001-V1
Recommendations For Proper Intrusion Protection
• For proper intrusion coverage, sensors should be located at every possible point of entry to a home or
premises. This would include any skylights that may be present, and the upper windows in a multi-level
building.
• In addition, we recommend that radio backup be used in a security system. This will ensure that alarm
signals can be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm
signals are normally sent over the phone lines, if connected to an alarm monitoring station).
-2-
LYNX Touch Installation and Setup Guide
Table of Contents
System Features.....................................................................................................................................................5
Mounting the Control ...........................................................................................................................................6
Wall Mounting ....................................................................................................................................................6
Desktop Mounting ..............................................................................................................................................6
Wiring Overview .................................................................................................................................................6
Wiring Connections...............................................................................................................................................7
AC Power and Backup Battery ..........................................................................................................................9
Installing/Configuring Communications Modules ......................................................................................10
General ..............................................................................................................................................................10
Connecting and Configuring Communications Modules ...............................................................................10
Installing Wireless Zones...................................................................................................................................12
General Information.........................................................................................................................................12
5800 Series Transmitter Loop Numbers.........................................................................................................12
Mechanics of Programming ..............................................................................................................................15
Navigating Menus ............................................................................................................................................15
General Programming Information.................................................................................................................16
Programming ....................................................................................................................................................17
Loading Factory Defaults.................................................................................................................................17
Exiting programming Mode .............................................................................................................................17
Zone Response Type Definitions .....................................................................................................................18
General ..............................................................................................................................................................18
Programming the Control .................................................................................................................................20
Change Installer Code......................................................................................................................................20
System Type......................................................................................................................................................21
Program Date and Time...................................................................................................................................23
Program the Communications Module ...........................................................................................................24
Program Zones ..................................................................................................................................................26
Program Keys ...................................................................................................................................................28
Reporter.............................................................................................................................................................30
Sounder .............................................................................................................................................................36
System Settings ................................................................................................................................................37
Communications Diagnostics...........................................................................................................................40
Remote Programming/Control (Downloading) ............................................................................................46
General Information.........................................................................................................................................46
Remote Programming Information .................................................................................................................46
System Operation ................................................................................................................................................48
Key/Touchscreen Operation.............................................................................................................................48
Panic key/Icons .................................................................................................................................................48
Security Codes ..................................................................................................................................................48
“Follow Me” System Announcement Feature .................................................................................................50
“Follow Me” Reminder Feature .......................................................................................................................51
-3-
LYNX Touch Installation and Setup Guide
Table of Contents (Continued)
Remote Phone Control Feature .......................................................................................................................51
System Displays................................................................................................................................................52
Zone Status Displays........................................................................................................................................52
Audio alarm Verification (Two-Way Voice Feature) ......................................................................................53
Testing the System ..............................................................................................................................................55
Event Log ..........................................................................................................................................................54
Contact ID & SIA Event Log Codes ................................................................................................................54
Test Mode ..........................................................................................................................................................55
Armed System Test ..........................................................................................................................................55
LYNX Touch Programming Default Tables...................................................................................................56
LYNX Touch SIA Programming Default Tables...........................................................................................59
Zone Programming Default Tables .................................................................................................................60
Regulatory Agency Statements........................................................................................................................63
Limitations of this System Statement ............................................................................................................64
UL Notices .............................................................................................................................................................65
SIA Quick Reference Guide ..............................................................................................................................65
Specifications .......................................................................................................................................................66
Contacting Technical Support .........................................................................................................................67
Glossary .................................................................................................................................................................68
Index .......................................................................................................................................................................69
Summary of Connections Diagram .................................................................................................................71
Warranty Information ........................................................................................................................ Rear Cover
-4-
LYNX Touch Installation and Setup Guide
System Features
The LYNX Touch control is a self-contained, rechargeable wireless control/communicator that features easy
installation and usage. A built-in speaker provides voice annunciation of system status along with voice
descriptors of each zone. An internal module (if provided) allows the LYNX Touch to communicate with the
Central Station via the Internet or GSM Cellular Wireless.
UL
LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
300-03866/LYNXRCHKIT-SHA) is installed.
Features
Alarm Output
• Built-in sounder
• Steady output for burglary/panic
• Temporal (3) pulse output for fire alarms
• Temporal (4) pulse output for carbon monoxide
alarms
• Long range radio (GSM)/audio alarm verification
• Trigger output
System Features
• 4.7-inch color graphic touch screen
• Message center (for user recorded messages)
• Voice announcement of system and zone status
• Voice chime
• Reminders
• Automatic stay arming
• Remote phone control
• Speaker phone operation
• “Follow me” reminder and system announcements
• 16 User Codes (Installer, Master, Babysitter,
Duress)
• 3 Panic Functions
• 16 Programmable reminders
Programming
• Options stored in EEROM
• Can be uploaded, downloaded or controlled via
IBM-compatible computer using Compass
downloader software and specified HAYES or
Honeywell CIA modem or via capable GSM or
IP communications module
• Flash downloading
Zones and Devices
• 64 total zones including 1 Hardwire (EOLR, N/C,
N/O) zone and up to 63 wireless zones (5800
Series transmitters)
• 2 Resident Monitor Zone Types
• Supports wireless keypads
• Built-in Case tamper
Other Features
• Exit error feature (detects difference between an
actual alarm and exit alarm caused by leaving a
door open after the exit delay expires)
• Event log stores up to 128 events
• RF jam detection
• Two installer programmable user phone
numbers
Communication
• ADEMCO Contact ID
• SIA (DC-03)
• Internet central station communication
• GSM cellular central station communication
• Two-way voice communication
• Supports AlarmNet remote services
System Power
• Primary Power: Plug-in Power Supply, 110VAC
to 9VDC, 2.7A output 300-04705 or 300-04065
(300-04063 in Canada)
• Backup battery: Rechargeable nickel-metal
hydride battery pack rated at 7.2Vdc. (P/N 30003864-1/LYNXRCHKIT-SC or 30003866/LYNXRCHKIT-SHA)
-5-
LYNX Touch Installation and Setup Guide
Mounting the Control
Wall Mounting
MOUNTING
HOOKS (HINGES)
1. Release the front case from the back case by
depressing the two locking tabs at the top of the unit
with the blade of a medium size screwdriver.
TIE WRAP
POINT (3)
2. Separate the front and back case assemblies by rotating
the front case so that it is perpendicular to the back
case and unsnapping (releasing) the two hooks from the
back case.
BACK
CASE
3. Feed the field wiring through the appropriate openings
in the back case. Use tie-wraps to secure the wiring to
the built-in wire loops as needed.
MOUNTING
HOLES (4)
4. Mount the back case to a sturdy wall.
ROTATE
FRONT CASE
UPWARD
TO RELEASE
HOOKS
5. Attach the front and back cases by connecting the
hooks on the front case to the attachments on the back
case. Once attached, the hooks will support the front
case and allow you to make the wiring connections.
6. After all wiring connections have been made, snap the
front case and back case closed and ensure that the case
is secured by the locking tabs.
TIE WRAP
POINTS (2)
FRONT
CASE
LOCKING
TABS
5000-100-091-V0
Desktop Mounting
For desktop mounting, the optional mounting base (model L5000DM, purchased separately) must be used.
1. Slide the control panel onto the mounting base locking
tabs.
2. Bring all wiring through the bottom of the mounting
base, using one of the wire entry locations, before
making connections to the control panel.
3. Use tie-wraps to secure the wiring to the built-in wire
loops as needed.
ARMED
READY
4. Use the supplied screws to secure the control panel to
the mounting base.
5000-100-092-V0
Wiring Overview
The following summarizes the connections required. Refer to the Wiring Connections paragraph and the
Summary of Connections diagram on the inside back cover when making connections.
TELEPHONE
CONNECTION
SUPER
HIGH CAPACITY
BATTERY
CONNECTION
STANDARD
CAPACITY BATTERY
CONNECTION
POWER SUPPLY
RECEPTACLE
TELEPHONE
CONNECTIONS
TERMINAL
STRIP
GSMVLP5/ILP5
RECEPTACLE
TAMPER
SWITCH
5000-100-087-V0
-6-
LYNX Touch Installation and Setup Guide
Wiring Connections
INCOMING
PHONE LINE
1. Make Earth Ground Connection - The designated earth ground
terminal EGND must be terminated in a good earth ground for the
lightning transient protective devices in this product to be effective.
The following are examples of good earth grounds available at
most installations:
RING
TIP
RED
Metal Cold Water Pipe - Secure a non-corrosive metal strap
(copper is recommended) to the pipe that is electrically connected
and secured to which the ground lead is electrically connected and
secured.
TO
PREMISES PHONES
RJ31X
GREY
AC Power Outlet Ground - Available from 3-prong, 120VAC power
outlets only. To test the integrity of the ground terminal, use a threewire circuit tester with neon lamp indicators, such as the UL Listed
Ideal Model 61-035, or equivalent, available at most electrical
supply stores.
a. Connect terminal EGND to a good earth ground as shown on the
Summary of Connections.
RING
TIP
BROWN
DIRECT
CONNECT
CORD
INCOMING
PHONE LINE
GREY
H/S R
BROWN
H/S T
RED
RING
GREEN
OR
OR
TIP
2. Make Phone Line Connections - For local or full line seizure
follow the appropriate steps below.
Local Seizure
a. Connect the incoming phone line to either the 8 position jack or
terminals TIP and RING on the LYNX Touch as shown on the
Summary of Connections.
b. Connect the handset phone lines to terminals H/S T (TIP) and
H/S R (RING) as shown on the Summary of Connections.
terminals as shown in the diagram or plug into the 8-position
Full Line Seizure: The control must be placed in series with the
incoming phone line. Plugging the Direct Connect Cord directly into
the RJ31X jack, allows the control to seize the phone line when an
alarm occurs and normal phone line usage by the premises
phones if the plug needs to be removed.
c. Cut the incoming RING and TIP phone lines (typically red and
green, respectively) and connect them to RJ31X terminals 4
(red) and 5 (green).
GREEN
8-POSITION
JACK
TO
PREMISES
PHONES
FULL LINE SEIZURE CONNECTIONS
d. Connect the premises end of the cut RING and TIP wires to
RJ31X terminals 1 (grey) and 8 (brown) respectively.
e. Wire the flying leads of a Direct Connect Cord to the control's
phone terminals as shown in the diagram or plug into the 8position jack.
f. Plug the Direct Connect Cord into the RJ31X jack.
HARDWIRED ZONE: If the EOLR is not at the end of the
loop, the zone will not be properly supervised, and the
system may not respond to an open circuit on the zone.
3. Hardwired Zone Connections - One EOLR supervised zone
supports both open circuit and closed circuit devices and has a
response time of 350msec. Maximum zone resistance: 300 ohms,
plus EOLR
Note: The hardwire zone cannot be used as a fire zone.
a. Connect sensors/contacts to the hardwired zone terminals GND
(-) and HWZ1 (+). Refer to the Summary of Connections
diagram.
b. Connect closed circuit devices in series in the high (+) side of
the loop. The EOL resistor must be connected in series with the
devices, following the last device.
c. Connect open circuit devices in parallel across the loop. The
2000-ohm EOLR must be connected across the loop at the last
device.
WIRING TABLE
DISTANCE BETWEEN
POWER SUPPLY AND CONTROL
4. AC Power Connections - Connect the Power Supply to the
receptacle on the LYNX Touch.
OR
Connect wires from the Power Supply to +9VDC and EGND
terminals as shown on the summary of connections diagram.
Up to 75 feet
75 to 150 feet
WIRE
GAUGE
# 20
# 18
5000-100-094-V1
-7-
LYNX Touch Installation and Setup Guide
Wiring Connections
Installing the L5000-RJ31X in the LYNX Touch Control
An auxiliary L5000-RJ31X receptacle can be installed in the LYNX Touch that will allow the telephone cable
to be disconnected without requiring the unit to be opened up.
1.
2.
3.
4.
5.
6.
7.
Using a wire cutter or knife cut the plastic tabs that secure the receptacle knockout from the left side of the LYNX Touch back case.
Connect four wires between the L5000-RJ31X receptacle terminal strip and the incoming phone line and the premises telephones
as shown on the figure below.
Install the L5000-RJ31X receptacle into the slot on the back case.
Connect one end of the L5000-RJ31X cable to the 8-position jack on the LYNX Touch PC board.
Route the cable through the opening in the back case and along the wire channel in the back case.
Connect the other end of the cable to the L5000-RJ31X receptacle on the side of the back case as shown below.
Secure the wires to the tie wrap points on LYNX Touch front and back case with the provided tie wraps.
To allow flush wall or desk mounting of the control, ensure that L5000-RJ31X cable is routed through the
channel in the case back. Ensure enough slack is left in the wires to allow the case to close without pinching
the wires.
INCOMING / PREMISES TELEPHONE WIRING
L5000-RJ31X
L5000-RJ31X
CABLE
REMOVE
KNOCKOUT
TIE WRAP
POINT
REFER TO
WIRING
SCHEMATIC
FOR
CONNECTIONS
L5000-RJ31X WIRING
TO PREMISES
TELEPHONES
TIP
RING
HS RING
HS TIP
L5000-RJ31X
TERMINAL STRIP
INCOMING
PHONE LINE
TIE WRAP
POINT
5000-100-155-V1
-8-
LYNX Touch Installation and Setup Guide
AC Power and Backup Battery
The system is powered by a 9 Volt DC, 2.7 Amp Plug-in Power Supply, 300-04705 or 300-04065 (300-04063
in Canada). Refer to the wiring table below for wire gauge and length. In the event of an AC power loss, the
system is supported by a long life backup battery that is supervised for connection and for low voltage
conditions. If the battery is missing, or a low battery condition is detected, a “low battery” message is
displayed and a report is sent to the central station. In addition, the system will beep once every 45 seconds
to audibly indicate a low battery condition (press any key to stop the beeping).
Use only the provided 300-04705 or 300-04065 (300-04063 Canada) Power Supply. Wiring to the Power
Supply must not exceed 300 feet using 16-gauge wire.
Do not plug the power supply into the AC outlet until after all wiring connections have been made. Ensure the
cover is snapped closed prior to applying AC power
The LYNX Touch is equipped with an integral, replaceable, rechargeable battery pack rated at 7.2Vdc.
Select the appropriate battery pack, based on the installation’s requirement, and install the battery pack.
Installing the Rechargeable Backup Battery
1. Remove battery retainer.
2. Insert battery pack into back case.
3. Route cable through channel (cutout) on left side of
compartment.
4. Install battery retainer.
5. Secure battery retainer with the provided screw.
6. Secure battery wiring in the wire routing clips (3).
7. Connect the battery connector to the receptacle on the PC
board.
8. After the wiring connection has been made, snap the front
and the back case closed.
9. Plug the power supply into a 24-hour, 110VAC unswitched
outlet. Upon powerup, the system will display "Please Wait
Checking System Integrity".
SCREW
SCREW
RETAINER
RETAINER
BATTERY PACK
(P/N 300-03866/
LYNXRCHKIT-SHA)
BATTERY PACK
(P/N 300-03864-1/
LYNXRCHKIT-SC)
OR
Replacing the Rechargeable Backup Battery
1. When battery replacement is required, unplug the
transformer from the wall outlet, and open the control panel
cover.
2. Remove the screw that secures the battery retainer.
3. Remove the battery retainer and disconnect the battery
pack connector from the receptacle on the PC Board.
4. Remove the battery pack from the back case.
5. Install a replacement battery pack (P/N 300-03864-1/
LYNXRCHKIT-SC or P/N 300-03866/LYNXCHKIT-SHA)
into the back case.
6. Route cable through channel (cutout) on left side of
compartment.
7. Install the battery retainer.
8. Secure battery retainer with the provided screw.
Secure battery wiring in the wire routing clips (3).
9. Connect the battery connector to the receptacle on the PC
board.
10. After the wiring connection has been made, snap the front
and the back case closed.
11. Plug the power supply into a 24-hour, 110VAC unswitched
outlet. Upon powerup, the system will display "Please Wait
Checking System Integrity".
Ensure the control panel assembly is snapped closed
prior to applying AC power. Rechargeable batteries may
take up to 48-hours to fully charge. The "Low Battery"
message should clear within four hours or by entering an
OFF sequence.
BATTERY
CABLE
CHANNEL
BATTERY
WIRE ROUTING
CLIPS (3)
Battery Selection
The LYNX Touch is equipped with an integral, replaceable, rechargeable
battery pack rated at 7.2Vdc. Select the appropriate battery pack,
based on the installation's requirement, and install the battery pack.
Battery Part Number
Battery StandbyTime
300-03864-1/
LYNXRCHKIT-SC
4-hours (minimum)
Approximately 1-hour before battery depletion
300-03866/
LYNXRCHKIT-SHA
24-hours (minimum)
At least 1-hour before batter y depletion
Low Battery Notification
5000-100-093-V0
-9-
LYNX Touch Installation and Setup Guide
Installing/Configuring Communication Modules
General
This LYNX Touch control supports central station reporting using wireless (GSM) and hardwire (IP)
communications modules. It also supports upload/download programming capability via the Internet or a
Private local area network (Intranet). This allows site maintenance independent of central station
monitoring, and modification to sites globally via the Internet or through a private LAN. Refer to the
instructions provided with the LRR/IP Communications Module being installed for additional information
regarding its installation, programming, and registration. The control is compatible with the following
AlarmNet Communications Modules:
• GSMVLP5 GSM Communication Module
• ILP5 Ethernet Communications Module
Communications Module 24-Hour Standby Power
If you require 24-hour standby, you must install the Super High Capacity battery P/N LYNX-RCHB-SHA in
the control.
RF Exposure
WARNING: The LYNX Touch must be installed to provide a separation distance of at least 7.8 in (20 cm)
from all persons and not co-located or operated in conjunction with any other transmitter.
Connecting and Configuring Communication Modules
Connect and configure the communications module as follows:
Installing the GSMVLP5 in the LYNX Touch Control
Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the
communications module in the LYNX Touch.
1.
2.
3.
Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated into the receptacle on
the control.
Secure the GSMVLP5 with the three provided screws.
Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device. Refer to the “Program the
Communications Module” and “Communications Diagnostics” sections.
The communications module must be registered with AlarmNet before downloading or alarm reporting can
take place.
SCREW
CONNECTOR
BOARD
CONNECTOR
BOARD
SIM
CARD
ROTATED
180
GSMVLP5
RECEPTACLE
LYNX TOUCH
5000-100-151-V0
- 10 -
LYNX Touch Installation and Setup Guide
Installing/Configuring Communication Modules
Installing the ILP5 in the LYNX Touch Control
Ensure that the connector board and cable are securely installed in the ILP5 before installing the
communications module in the LYNX Touch.
1.
2.
3.
4.
5.
6.
7.
8.
Using a wire cutter or knife cut the plastic tabs that secure the ILP5 spacer from to the back case of the LYNX Touch.
Remove the ILP5 receptacle knockout from the left side of the LYNX Touch back case.
Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated into the receptacle on the
control.
Secure the ILP5 with the three provided screws.
Insert the ILP5 receptacle and spacer into the slot on the back case.
Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap.
Connect the Ethernet cable to the RJ45 receptacle.
Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the “Program the
Communications Module” and “Communications Diagnostics” sections.
Alternate Installation (Refer to the Alternate Installation as shown on the figure below)
1.
2.
3.
4.
5.
6.
Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated into the receptacle on the
control.
Secure the ILP5 with the three provided screws.
Insert the ILP5 receptacle into the slot on the back case as shown on the figure below.
Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap.
Connect the Ethernet cable to the RJ45 receptacle.
Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the “Program the
Communications Module” and “Communications “Diagnostics” sections.
The communications module must be registered with AlarmNet before downloading or alarm reporting
can take place.
ETHERNET CABLE
TO ILP5
RJ45 RECEPTACLE
LYNX TOUCH
ALTERNATE INSTALLATION
REMOVE ILP5
KNOCKOUT
REMOVE ILP5
SPACER
ILP5 SPACER
RJ45
RECEPTACLE
CONNECTOR
BOARD
ROTATED
180
TIE
WRAP
(1)
TIE
WRAP
POINT
CONNECTOR BOARD
SCREW
(3)
ILP5
RECEPTACLE
LYNX TOUCH
5000-100-154-V0
- 11 -
LYNX Touch Installation and Setup Guide
Installing Wireless Zones
General Information
Zones
The control supports up to 64 total wireless zones using 5800 Series transmitters, and wireless buttons.
Range
The built-in RF receiver can detect signals from wireless transmitters within a nominal range of 200 feet.
Transmitters
5800 Series transmitters have built-in serial numbers that must be entered into the system using the
“Zones” programming section, or input to the control via the downloader. 5800 Series transmitters (except
the 5800RL) do not have DIP switches. Each transmitter's zone number is also programmed into the system
in the “Zones” programming section. Some transmitters, such as the 5816 and 5817, can support more than
one "zone" (referred to as loops or inputs). On the 5816, for example, the wire connection terminal block is
loop 1; the reed contact is loop 2. Each loop must be assigned a different zone number.
For button transmitters (RF "keys") such as the 5804, you must assign a unique zone number to each
individual button used on the transmitter. Each button on the transmitter also has a pre-designated loop
or input number, which is automatically displayed.
UL
The 5816 and 5817 Transmitters do not have EOL supervision of their loop wiring, which must not exceed 3 feet.
The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819S(WHS & BRS), 5828/5828V
and 5850(GBD) transmitters have not been evaluated by UL.
House Identification
If you are using a 5804BD/5804BDV Wireless Keypad with the system, you must program a House ID Code
(01–31) as described in the “SYSTEM TYPE” programming section to establish proper communication, and
the keypad must be set to the same ID. House ID 00 disables all wireless keypads. An RF House ID is not
necessary for other 5800 Series transmitters; the entry should be left at “00” (default) in those cases.
Transmitter Supervision
With the exception of some transmitters/keypads that may be carried off-premises (5804, 5804BD,
5804BDV, 5804E and 5805-6), each transmitter is supervised by a check-in signal that is sent to the
receiver at 70–90 minute intervals. If at least one check-in is not received from each supervised transmitter
within a 12-hour period, the "missing" transmitter zone number(s) and "Supervision" will be displayed. The
supervision for a particular transmitter in the system that may also be carried off the premises
(5802/5802MN2, 5802MN) may be turned off by entering it as a Unsupervised RF (UR) type, as described in
the “ZONES” programming section. 5800 Series transmitters have built-in tamper protection and will
annunciate as a fault condition if covers are removed.
Transmitter Input Types
Each of the transmitters has one or more unique factory-assigned input (loop) ID codes. Each of the inputs
requires a programming zone (e.g., a 5804's four inputs require four button zones). Transmitters can be entered
as one of the following types (see transmitter’s instructions for appropriate input type):
Type
Supervised RF ("RF")
Unsupervised RF ("UR")
Unsupervised Button RF ("BR")
Description
Sends periodic check-in signals, as well as fault, restore, and low battery signals. The
transmitter must remain within the receiver's range.
Sends all the signals that the "RF" type does, but the control does not supervise the check-in
signals. The transmitter may therefore be carried off-premises.
Sends only fault signals. They do not send low battery signals until they are activated. The
transmitter may be carried off-premises.
Transmitter Battery Life
• Batteries in the wireless transmitters may last from 4–7 years, depending on the environment, usage,
and the specific wireless device being used. Factors such as humidity, high or low temperatures, as well
as large swings in temperature may all reduce the actual battery life in a given installation. The wireless
system can identify a true low battery situation, thus allowing the dealer or user of the system time to
arrange a change of battery and maintain protection for that point within the system.
• Button-type transmitters should be periodically tested for battery life. The 5802MN, 5802MN2, 5804,
5804BD, 5804BDV, and 5804E button transmitters have replaceable batteries.
- 12 -
LYNX Touch Installation and Setup Guide
Installing Wireless Zones
RF Sniffer Test Mode
This mode is used after all transmitters have been entered to check that all transmitters have been
properly programmed. Sniffer mode does not automatically expire. You must manually exit Sniffer mode by
selecting Off and entering the Installer Code to return to normal operation.
SCREEN
ACTION
Test
5000-100-096-V0
RF Sniffer
Test
5000-100-102-V0
Notes: (1)
(2)
(3)
(4)
1. At the Tools Screen, select “Test”. The following options are displayed.
Walk Test
RF Sniffer Test
Go-No-Go Test
Dialer Test
2. Select “RF Sniffer Test” from the options.
Note: If the communicator is in the process of sending a report to the central station, the
system will not go into the Sniffer mode. If so, wait a few minutes and try again.
3. The system displays all programmed zone numbers and zone descriptors, which have a
non-zero Zone Type. Fault each transmitter in turn, causing each one to send a signal. As
the system receives a signal from each of the transmitters, the zone number of that
transmitter disappears from the display. The transmitters may be checked upon installation,
or in an installed system. The system will beep once every 30-40 seconds while the RF
Sniffer Test mode is active.
4. When all transmitters have been checked, Exit RF Sniffer Test mode by depressing the Off
key and entering the Installer or a User Code.
All button-type (BR) units must physically be activated to clear the display, since they do not automatically send
check-in signals.
When one button of a button type, supervised or unsupervised RF transmitter (RF, UR, or BR) is activated, all zones assigned
to other buttons on that transmitter are cleared. This also applies to 5816 and 5817 transmitters that have multiple loops
(zones).
Any transmitter that is not “entered” will not turn off its zone number.
For SIA installations, the following devices may be used as specified for panic (24-hour) alarm response:
• wireless keys which have two-button panic pairs available (e.g., 5804BDV), on which only the two-button panic pairs may
be programmed for any 24-hour alarm response
• wireless keypads (e.g., 5828/5828V) keypads that have a two-second delay on the special function keys, or two-button panic
pairs
• built-in keypad panic key
Go/No Go Test Mode
Conducting this test with your hand wrapped around the transmitter will cause inaccurate results.
On button type transmitters that have been programmed to set ARM AWAY, ARM STAY, or DISARM, pressing a
button will take the system out of the Go/No Go Test mode causing the programmed action to occur.
The Go/No Go tests will verify adequate RF signal strength from the proposed transmitter location, and
allow you to reorient or relocate transmitters if necessary, before mounting the transmitters permanently.
This mode is similar to the transmitter Test mode, except that the wireless receiver gain is reduced. This
will enable you to make sure that the RF signal from each transmitter is received with sufficient signal
amplitude when the system is in the normal operating mode.
SCREEN
ACTION
1. At the Tools Screen, select “Test”. The following options are displayed.
Test
5000-100-096-V0
2.
3.
Go-No-Go
Test
5000-100-103-V0
4.
5.
6.
Walk Test
RF Sniffer Test
Go-No-Go Test
Dialer Test
Select “Go-No-Go Test”.
Once you have placed transmitters in their desired locations, and the approximate length of
wire to be run to sensors is connected to the transmitter's screw terminals (if used), fault
each transmitter.
a. The keypad beeps three times indicating signal reception, displays the appropriate
zone number and announced the zone description.
b. If the keypad does not beep, reorient or move the transmitter to another location.
Usually a few inches in either direction is all that is required.
If each transmitter produces the proper keypad response when faulted, they can be
permanently mounted according to their respective instructions.
The system will beep once every 30-40 seconds while the Go-No-Go Test mode is active.
Exit Go-No-Go Test mode by depressing the Off key and entering the Installer or a User
Code.
- 13 -
LYNX Touch Installation and Setup Guide
Installing Wireless Zones
5800 Series Transmitter Loop Numbers
(Refer to this information when programming transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop
designations.
LOOP
LOOP 1
LOOP
LOOP 1
(LOW
SENSITIVITY
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
LOOP 4 (TAMPER)
5800CO
ENROLL AS "RF"
5800Micra
ENROLL AS "RF"
5800PIR-RES
ENROLL AS "RF"
5800PIR/
5800PIR-COM
ENROLL AS "RF"
5800RL
SET
HOUSE ID
5800PIR-OD
ENROLL AS "RF"
LOOP 3
ON
LOOP 4
5800SS1
E N RO L L A S " R F "
5 8 0 0 WAV E
P RO G R A M
HOUSE ID
SERIAL #1
LOOP 3
ON
LOOP 1
5804/5804E
ENROLL AS "BR"
5802MN2
ENROLL AS
"UR" OR "RF"
5802MN
ENROLL AS
"UR" OR "RF"
LOOP 1
•
•• •••
••• • •
• ••
5 8 0 4 B D / 5 8 0 4 B DV
ENROLL AS "BR"
PROGRAM HOUSE ID
SERIAL #1
LOOP 2
OF
LOOP 2
(REED)
SERIAL #1
LOOP 1
SERIAL #2
LOOP 3
LOOP 1
LOOP 1
LOOP 1
SERIAL #2
LOOP 2
5806/5806W3/5807
5808/5808LST/5808W3
ENROLL AS "RF"
5809
ENROLL AS "RF"
5811
ENROLL AS "RF"
LOOP 1
(PRIMARY)
LOOP 2
(REED)
LOOP 1
(TERMINALS)
LOOP 3
(AUX.
RIGHT)
5817
ENROLL AS "RF"
LOOP 1
(TERMINALS)
5819
ENROLL AS "RF"
5818
ENROLL AS "RF"
SERIAL #2
LOOP 3
MIC
LOOPS
1-3
MESSA
LOOP 1
LOOP 2
(STANDARD
SECURITY)
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
5828/5828V
P RO G R A M
HOUSE ID
LOOP 1
LOOP 1
(INTERNAL
SHOCK
SENSOR
5819S (WHS & BRS)
ENROLL AS "RF"
LOOP 1
(HIGH
SECURITY)
SERIAL #2
LOOP 4
GE
SERIAL #1
LOOP 4
5821
ENROLL AS "RF"
LOOP 2
(REED)
SERIAL #1
LOOP 2
AR
AD
5816
ENROLL AS "RF"
5820L
ENROLL AS "RF"
SERIAL #2
LOOP 1
SERIAL #1
LOOP 3
ME
5814
ENROLL
AS "RF"
LOOP 3
(TERMINALS)
LOOP 3
(TERMINALS)
LOOP 1
5816TEMP
ENROLL AS "RF"
5816MN
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 2
(AUX.
CENTER)
LOOP 1
(TEMP
SENSOR)
ALTERNATE
POSITION
FOR LOOP 2
RE
LOOP 1
(TERMINALS)
LOOP 1
SERIAL #2 - LOOP 1 = ON + 4 BUTTONS
LOOP 4 = 3 + 4 BUTTONS
5805-6
ENROLL AS "BR"
5834-4
ENROLL AS "BR"
LOOP 3 (TILT MODE)
5853
ENROLL AS "RF"
LOOP 1
(MOTION)
5870API
ENROLL AS "RF"
LOOP 4 (TAMPER)
SERIAL #1
LOOP 3
AW
AY
SERIAL #1
LOOP 4
ST
AY
SERIAL #2
LOOP 3
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
5878
ENROLL AS "BR"
LOOP 1
(LOW SENSITIVITY)
LOOP 1
5890/5890PI
ENROLL AS "RF"
LOOP 4
LOOP
5894PI
ENROLL AS "RF"
LOOP 2
(HIGH SENSITIVITY)
LOOP 1
5897
ENROLL AS "RF"
5898
ENROLL AS "RF"
5800-002-V0
SERIAL #1
LOOP 4
LOOP 1
LOOP
LOOP 2
LOOP 2
LOOP 1
••
•
••
LOOP
OFF
Notes: (1) The 5806W3 smoke detector must be used in SIA applications.
(2) Button type (BR) devices send only fault and low battery signals; no restore or check-in signals.
Supervised RF (RF) devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised RF (UR) devices send periodic check-in signals, faults, restore and low battery signals but the
control does not supervise the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
UL
The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5814, 5816TEMP, 5819, 5819S(WHS & BRS), and
5828/5828V wireless transmitters have not been evaluated by UL.
- 14 -
LYNX Touch Installation and Setup Guide
Mechanics of Programming
Navigating Menus
Touch-screen Display
LYNX Touch’s Liquid Crystal Display (LCD) touch-screen displays variable icons and text on “screens”. The
screen displays status icons and associated text, the current time, system status information and menu
choices. The Menu area includes a list of commands, or choices that apply to the current selection. The
status area provides information about various system events and a colored bar also provides an indication
of system status. A “Home Screen” is displayed whenever power is applied to the system. In addition the
green “READY” LED is lit when the system is ready or flashes when it is not.
SYSTEM
STATUS
Ready To Arm
SYSTEM/ZONE
STATUS
Zones
Arm Away
Delay
LEDs
Arm Stay
Message
10:18 AM June 8, 2010
ARMED
System
Phone
More
READY
FUNCTION
KEYS
5000-100-054-V0
Home Screen (page 1)
Navigation Keys
Navigating through the screens is accomplished by lightly touching the menu item on the touch-screen.
Once activated, the control will take you to the next screen. Selecting the “Home” (cancel) key or the “2”
Key will return you to the previous screen at any time unless System Programming mode is active. By
Touching (selecting) an icon or key the system, depending on the function, advances to another screen,
toggles between options or scrolls through multiple options that can be selected. The system provides a
prompt when a specific input is required.
Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow you to clearly hear
the feedback announcements or system beeps from the system’s built-in speaker. To adjust the volume, select “More” on the
“home Screen” and then select “Settings”. Adjust the volume using the slide displayed on the Settings screen and then select
“Save” to accept. Upon exiting the Program Mode, the system resets the volume to the default value (mid level).
Menu Screens
System Status is displayed at the top of each screen. The time and date are displayed at the bottom of the
Home Screen. The Home Screen consists of two pages. The first page displays the system status and eight
selection “buttons” and “tabs”.
Selection
Zones
System
Arm Away
Arm Stay
Message
Phone
Delay/Instant
More
Function
Provides access to Zone information and options.
Provides information about system status
Used to Arm the system in Away mode (displayed on both Home Screen pages).
Used to Arm the system in Stay mode (displayed on both Home Screen pages).
Provides access to Message Center.
Provides access to Speaker Phone mode. (if programmed)
Used to toggle between exit delay and instant arming options (displayed on Home Screen pages).
Advances system to second page of the Home Screen.
- 15 -
LYNX Touch Installation and Setup Guide
Mechanics of Programming
The second page also displays the system status in and six selection “buttons” and “tabs”.
Selection
Tools
Arm Away
Arm Stay
Settings
Delay/Instant
Back
Function
Provides access to Installer and User Programming Menus (Master User Code required for access).
Used to Arm the system in Away mode (displayed on both Home Screen pages).
Used to Arm the system in Stay mode (displayed on both Home Screen pages).
Provides access to various keypad functions (i.e.; Brightness, Contrast, Volume, Voice, Chime & Ringer).
Used to toggle between exit delay and instant arming options (displayed on both Home Screen pages).
Returns system to first page of the Home Screen.
Installer Tools Menu
The Tools/Installer Menu provides access to the Installer configurable features and displays six options.
Entering the Installer Code is required to access the Installer Menu.
Ready To Arm
Program
Test
Devices
Events
Initiate
Download
Schedules
5000-100-043-V0
Installer Menu Page
User Tools Menu
The User Menu provides access to the User configurable features and displays eight options. Entering the
Master User Code is required to access the User Menu.
Ready To Arm
Users
Devices
Schedules
Test
Date Time
Events
Reminders
Slide Show
Back
5000-100-070-V0
User Menu Page
General Programming Information
When power cycling the control, remove AC power first and wait approximately 1 minute before
disconnecting battery.
Programming options are stored in non-removable, electrically erasable, nonvolatile EEROM memory. The
system can be programmed at any time, even at the installer's premises prior to the actual installation.
Simply apply power temporarily to the Control and then program the unit as desired.
The system can also be programmed remotely, using an IBM PC compatible Personal Computer, and
Compass Downloader and modem or via capable GSM or IP communications modules. See the Remote
Programming/Control (Downloading) section.
- 16 -
LYNX Touch Installation and Setup Guide
Mechanics of Programming
Programming
If the system is Armed or in Alarm, the Tools icon will not be functional. The system must first be
disarmed.
To enter Installer Programming Mode:
SCREEN
ACTION
Ready To Arm
Zones
Arm Away
Arm Stay
Message
System
At the Home Screen select “More”.
Select “Tools”. The system displays a virtual keypad.
Enter the Installer Code 4112.
The System Programming Screen is displayed. Select “Program” to
display the following options:
Installer Code
Date Time
Zones
Keys
Phone
10:18 AM June 8, 2010
Delay
1.
2.
3.
4.
More
5000-100-006-V0
System Type
Communications
Comm. Diagnostics
Reporter
Use the down T arrow to scroll to the next page of options.
Sounder
Default Config.
5.
System Settings
Selecting an option advances to that Programming screen.
Loading Factory Defaults
To load the factory defaults, enter the Installer Programming Mode and advance to second page of the
System Programming and refer to following procedure. Refer to the Programming Default Tables section of this
manual to view the Default Tables.
If a default table is loaded, any data that has already been programmed into the system will be changed
according to the default table selected!
To Select a Default Configuration
SCREEN
ACTION
1. Select “Default Configuration” to display the following options:
System Programming...
Sounder
System Settings
Default Config.
5000-100-035-V0
Default Config 2
Default Config 1
Default Config 4
Default Config 3
Default Downloader
Note: For a list of the pre-programmed defaults refer to the Default Tables
section.
2. Select the desired Default Configuration.
3. A Confirmation screen is displayed.
4. If “Yes” is selected, the System beeps three times and returns to the
Default option screen.
5. If “No” is selected, the System returns to the Default option screen.
Exiting Program Mode
1. Select the “2” key to exit the current screen. The system returns to the previous screen.
2. Select the “2” key as required until system displays a Confirmation screen.
3. Select “Yes” to allow the installer to re-enter Programming mode or “No” to prevent re-entry. If “No” is
selected, you can still re-enter Program Mode by powering down the unit (remove AC and battery
power) and entering Program Mode within 30 seconds of powering up.
4. Select the “2” key again to return to the Home Screen.
- 17 -
LYNX Touch Installation and Setup Guide
Zone Response Type Definitions
General Information
During programming, you must assign a zone type to each zone, which defines the way in which the system
responds to faults in that zone. Zone types are defined below.
Type
Function
Characteristics
•
•
•
•
•
Not Used
Entry/Exit 1
(Burglary)
Used to program a zone that is not used.
Usually assigned to sensors or contacts on
primary entry and exit doors.
Entry/Exit 2
(Burglary)
Usually assigned to sensors or contacts on
secondary entry and exit doors that might be
further from the keypad (typically used for a
garage, loading dock, or basement door).
Perimeter
(Burglary)
Interior, Follower
24-hour Silent
Alarm
Usually assigned to all sensors or contacts on
exterior doors and windows
Usually assigned to a zone covering an entry
area (i.e.: foyer, lobby, or hallway) that one
must pass upon entry (after faulting the
entry/exit zone) to reach the keypad. It provides
an instant alarm if the entry/exit zone is not
violated first, and protects an area in the event
an intruder has hidden on the premises before
the system is armed, or gains access to the
premises through an unprotected area.
Usually assigned to a zone that covers a
sensitive area (i.e.: stock room, drug supply
room, etc.) It can also be used on a sensor or
contact in an area where immediate notification
of an entry is desired.
Usually assigned to a zone containing an
Emergency button (silent emergency).
24-hour Audible
Alarm
Usually assigned to a zone containing an
Emergency button (audible emergency).
24-hour
Auxiliary Alarm
Usually assigned to a zone containing a
button for use in personal emergencies or to
a zone containing monitoring devices (i.e.:
water or temperature sensors, etc.).
Can be assigned to any wireless zone used as
a fire zone. This zone type is always active and
cannot be bypassed.
Bypassed when the panel is armed in the STAY
or STAY INSTANT mode.
Trouble by Day/
Alarm by Night
Fire No
Verification
Interior with Delay
Monitor
Can be assigned to any wireless zone used for
asset protection. Works as a dynamic monitor
of a zone fault/trouble (not alarm).
24-hour Carbon
Monoxide Monitor
Can be assigned to any wireless zone with a
carbon monoxide detector. This zone type is
always active and cannot be bypassed.
- 18 -
•
•
•
•
•
•
•
•
•
•
•
None
Entry delay #1 is programmable.
Exit delay is independently programmable.
Exit and entry delays when armed in AWAY or STAY mode.
No entry delay when armed in STAY INSTANT or AWAY
INSTANT mode.
Exit delay regardless of the arming mode selected.
Entry delay #2 is programmable.
Exit delay is independently programmable.
Secondary entry delay, if armed in the AWAY or STAY mode.
No entry delay when armed in the STAY INSTANT or AWAY
INSTANT mode.
Exit delay begins regardless of the arming mode selected.
Instant alarm, when armed in AWAY, STAY, STAY NO DELAY,
or AWAY INSTANT mode.
Delayed alarm (using the programmed entry/exit time) if
entry/exit (types 01 or 02) or interior-with-delay (type 10) zone is
faulted first.
Instant alarm in all other situations.
Active when armed in AWAY or AWAY INSTANT mode.
Bypassed automatically when armed in STAY or STAY
INSTANT mode.
• Instant alarm, when armed in AWAY, STAY, STAY INSTANT, or
AWAY INSTANT (night) mode.
• Provides a latched trouble sounding from the keypad and, if
desired, a central station report when disarmed (day).
• Sends a report to the central station but provides no keypad
display or sounding.
• In disarmed state sends a report to the central station displays
"Not Ready to Arm" on the keypad and “AWAY”, “STAY” and
“TOOLS” buttons are disabled.
• Follows sounder timeout
• Sends a report to the central station, and provides alarm sounds
at the keypad.
• Sends a report to the central station and provides an alarm
sound at the keypad. (There is no keypad timeout.)
• Alarm sound will pulse when this zone type is alarmed.
• Entry delay #1 (with programmed entry time) when armed in the
AWAY mode.
• Entry delay begins whenever sensors in this zone are violated,
regardless of whether an entry/exit delay zone was tripped first.
• No entry delay when armed in the AWAY INSTANT mode.
• Exit delay regardless of the arming mode selected.
• No reports to the central station.
• Fault/restore events are logged by the system.
• Activity Zone No. and Zone Descriptor displayed on LCD.
• Restore will be stored in event log.
• No keypad sounding or chime
• System can still be armed
• Local keypad and detector will sound when this zone type is
alarmed. (Pulse Temporal 4)
LYNX Touch Installation and Setup Guide
Zone Response Type Definitions
Function
Characteristics
Fire with
Verification
Type
Can be assigned to any wireless zone used as
a fire zone. Fire with verification is available
with smoke detector device type. It can not be
used with heat detectors, combination
heat/smoke detectors, wireless sensors or fire
pull stations. This zone type is always active
and cannot be bypassed.
Arm–Stay
Special-purpose zone type used with 5800
Series wireless pushbutton units.
Arm–Away
Special-purpose zone type used with 5800
Series wireless pushbutton units.
• Alarm sound will pulse when this zone type is alarmed. Only
after the alarm has been verified.
• System verifies alarm by delaying reporting and control panel
alarm sounding for 30 seconds after alarm is detected. If the
zone remains faulted after 30 seconds a fire alarm is provided. If
any other fire zone is faulted during the 30 second delay window
a fire alarm is immediately provided for that zone. An alarm for
original fire zone will also be provided if that zone is still faulted
afterward. If there are no fire alarms after the 30 second delay
expires, the system will open a 60 second window. If any fire
zone is faulted during that window a fire alarm will immediately
be provided for that zone.
• Exit delay regardless of the arming mode selected.
• System is armed in the STAY mode when the zone is activated.
• System is armed in the AWAY mode when the zone is activated.
Disarm
Special-purpose zone type used with 5800
Series wireless pushbutton units.
Assigned when no-alarm response is required
No Alarm
Response
Silent Burglary
Usually assigned to sensors or contacts on
exterior doors and windows where sirens are
NOT desired.
General Monitor
Assigned sensors or contacts on doors and
windows or asset protection within the
premises. Used to track activity of the occupant
and alert occupant of the activity of others.
General
Response
Assigned sensors or contacts on doors and
windows or asset protection within the
premises. Used to track activity of the occupant
and alert occupant of the activity of others.
• Disarms the system when the zone is activated.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Resident Monitor
Used to monitor a resident in an area deemed
to be dangerous by a caregiver.
•
•
•
•
•
Resident
Response
Used to monitor a resident in an area deemed
to be dangerous by a caregiver. Requires
acknowledgement by caregiver.
•
•
•
•
•
•
•
•
- 19 -
No reports to the central station.
Activity Zone No. and Zone Descriptor displayed on LCD.
No keypad sounding or chime
System can still be armed
No display on the screen
Instant alarm, with NO audible indication when is armed in the
AWAY, STAY, STAY NO DELAY, or AWAY INSTANT mode.
Report sent to the central station.
No reports to the central station.
Fault/restore events are logged by the system.
Monitors entry into a monitored area. Activates a one-time unique
chime sound and announcement when faulted.
Activity Zone No. and Zone Descriptor displayed on LCD.
Restore will be stored in event log.
No reports to the central station.
Fault/restore events are logged by the system.
Monitors entry into a monitored area. Activates a unique chime
sound and zone announcement when faulted.
Activity Zone No. and Zone Descriptor displayed on LCD.
System re-triggers audible sounding every ten seconds until
acknowledged (Off sequence or wireless key button).
No reports to the central station.
Monitors entry into a monitored area. Activates a unique chime
sound and zone announcement when faulted.
Activity Zone No. and Zone Descriptor displayed on LCD.
If programmed, triggers a voice message (follow me) report.
If triggered by a PIR, the system remains latched until another
Monitor or Response zone has been tripped or a specified time
interval has elapsed.
Fault/Restore events are not logged by the system.
No reports to the central station.
Monitors entry into a monitored area. Activates a unique chime
sound and zone announcement when faulted.
Activity Zone No. and Zone Descriptor displayed on LCD.
If programmed, triggers a voice message (follow me) report.
If triggered by a PIR, the system remains latched until another
Monitor or Response zone has been tripped or a specified time
interval has elapsed.
System re-triggers audible sounding every ten seconds until
acknowledged (Off sequence or wireless key button).
Fault/Restore events are not logged by the system
LYNX Touch Installation and Setup Guide
Programming the Control
After entering the System Programming mode select from the options provided on the First and Second
Installer Programming screens as shown in the accompanying figure.
System Programming...
System Programming...
Installer Code
System Type
Sounder
Date Time
Communicator
Default Config.
Zones
Comm. Diagonostics
Keys
Reporter
System Settings
Save
5000-100-035-V0
5000-100-013-V0
Page 1
Page 2
Change Installer Code
The factory default Installer Code for the LYNX Touch Control is set to 4-1-1-2.
SCREEN
ACTION
Installer Code
1.
Select “Installer Code”.
2.
Enter a new four-digit Installer Code on the displayed keypad The system will display the
new code on the left side of the screen.
Select “Done” when you are finished.
The system returns to the “System Programming” Screen.
5000-100-129-V0
3.
4.
- 20 -
LYNX Touch Installation and Setup Guide
Programming the Control
System Type
The following system options are programmed in this section:
Option
RF Jam
Speaker Phone
Two Way Voice
RF House Code
Phone Notification
Phone Detect Time
Remote Phone
Events
Non-Security
Remote Access
Serial
Multi Mode Serial
Function
Enable or disable RF Jam Log and Reporting
Enable or disable Speaker Phone mode. (End User feature)
Enable or disable Two Way Voice communication with the Central Station.
Set RF House Code. (Bi-directional RF Devices)
Enable or disable Phone Notification mode. (Phone Line-cut)
Select a delay period between phone line-cut & system response (allows phone to restore)
Enable or disable Remote Phone Control mode. (End User feature)
Enable or disable multiple options for event logging (i.e.; alarms, troubles, open/close)
Enable or disable non-security event logging
Enable or disable end user to access their system via a website
Enable or disable transmission of panel status events via email (Active only when Remote Access
Serial is enabled)
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless
otherwise noted.
Screen
ACTION
System Type
5000-100-130-V0
System Type
Note: If applicable, the pre-programmed default will be displayed beneath the option.
1.
Select “System Type” from the following options:
RF Jam
Speaker Phone
Two Way Voice
RF House Code
Phone Notification
Remote Phone
Phone Detect Time
Use the down T arrow to scroll to the next page of options.
Events – Log All
Events – Log Alarm
Events – Log Bypass
Events – Log Open/Close
Events – Log Trouble
Non-Security
Remote Access Serial
Multi Mode Serial
Speaker Phone
Enabled
Two Way Voice
Disabled
RF House Code
Phone Notification
Disabled
Phone Detect Time
2 Minutes
3. Select “Speaker Phone”. The System toggles between the following:
Disabled
Enabled
4. Select “Two-Way Voice” .The System toggles between the following:
Disabled
Enabled
5. Select “RF House Code”.
6. After entering a code (00-31) on the displayed keypad, select “Done”.
7. Select “Phone Notification” (phone line cut). The System scrolls between the following
options:
Disabled
Keypad
Trouble
If “Keypad” or “Trouble is selected proceed to Step 8.
8. If Keypad or Trouble was selected in Step 7, the “Phone Detect Time” option is
displayed. Select “Phone Detect Time”. The system scrolls between the following options:
1 Minute
2 Minutes
3 Minutes
4 Minutes
- 21 -
LYNX Touch Installation and Setup Guide
Programming the Control
Screen
Remote Phone
Enabled
Events - Log All
Press To Log All
Events – Log Alarm
Enabled
ACTION
9. Select “Remote Phone”. The System toggles between the following options:
Disabled
Enabled
Use the down T arrow to scroll to the next page of options.
10. Select “Events - Log All”. The system displays “Press To Log All”. Selecting this option
programs the system to log all events and “Log All Set” is displayed. Additionally all of the
options listed below are enabled.
Events – Log Alarm
Events – Log Bypass
Events – Log Open/Close
Events – Log Trouble
Non-Security
OR
Proceed to step 11 and select the options individually.
11. Select “Events – Log Alarm”. The System toggles between “Enabled” and “Disabled.
12. Select “Events – Log Bypass”. The System toggles between “Enabled” and “Disabled”.
13. Select “Events – Log Open/Close”. The System toggles between “Enabled” and
“Disabled”.
14. Select “Events – Log Trouble”. The System toggles between “Enabled” and “Disabled”.
Remote Access Serial
Disabled
Non Security
15. Select “Remote Access Serial”. The System toggles between “Enabled” and “Disabled”.
If the Remote Access Serial” option is enabled, the “Multi Mode Serial” option is
displayed.
16. Select “Non Security”. The System toggles between “Enabled” and “Disabled”.
Disabled
Multi Mode Serial
Disabled
17. Select “Multi Mode Serial”. The System toggles between “Enhanced Reports” and
“Disabled”.
18. Select “Save” when complete.
- 22 -
LYNX Touch Installation and Setup Guide
Programming the Control
Program Date and Time
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless otherwise noted.
SCREEN
ACTION
Note: If you are installing a GSMVLP5 or ILP5 Communication Module, the
time and date will be programmed and updated automatically via
Central Station. You must still program the correct Time Zone below.
1. Select “Date Time”.
Date Time
5000-100-131-V0
System Programming...
June
SUN
2.
Using the left W and right X arrows select the Month and Year then
select the date. Select the T key to advance to the next screen.
3.
To set the correct time, touch the “Clear” button.
4.
Enter the correct time and then select AM or PM. Select the T key to
advance to the next screen or select “Save” to return to the System
Programming Screen.
2010
MON
TUE
WED
THU
FRI
SAT
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Save
5000-100-016-V0
System Programming
Enter Time
Clear
10:21 AM
AM / PM
Save
5000-100-010-V0
Time Zone
Eastern (EST)
Day Light Savings Time
Yes
Start Month
March
Start Week
Second
End Month
November
End Week
First
6.
Select “Time Zone”. The system scrolls between the following options:
Eastern (EST)
Mountain (MST)
Central (CST)
Pacific (PST)
Hawaii (HAST)
Alaska (AKST)
6. Select “Day Light Savings Time”. The system toggles between “Yes” and
“No”. If “Yes” is selected the following options will become active.
7. Select “Start Month”. The system displays the following options.
January
February
March
April
May
June
July
August
Use the down T arrow to scroll to the next page of options.
September
October
November
December
8. Select “Start Week”. The system scrolls between the following options.
First
Fourth
3rd from Last
Second
Last
Third
Next to Last
9. Select “End Month”. The system displays the following options.
January
February
March
April
May
June
July
August
Use the down T arrow to scroll to the next page of options.
September
October
November
December
10. Select “End Week”. The system will scrolls through the available weeks.
First
Fourth
3rd from Last
Second
Last
Third
Next to Last
11. After programming these options, select the “Save” key.
- 23 -
LYNX Touch Installation and Setup Guide
Programming the Control
Program the Communications Module
The following system options are programmed in this section:
Option
Communications Path
Primary City Id
Primary Central Station Id
Primary Subscriber Id
Supervision
Old Alarm Time
Remote Acc. IP or GSM
Multi Mode IP or GSM
IP Fault Time
Use DHCP
NIC IP Address
Subnet Mask
Gateway IP Address
DNS Server IP Address
GSM Fault Time
GSM Rollover
GSM 24 Hour Test
Function
Selects type of Communications Module
Enter Central Station Primary City ID
Enter Primary Central Station ID
Enter Central Station Primary Subscriber ID
Selects how often the Communications Module sends a supervisory message to the Central
Station.
Selects how long an undeliverable alarm delivery is retried to the Central Station.
Enables or disables user remote access via internet and/or GSM.
(appears only if Remote Access IP or GSM is enabled.) Enables or disables multi mode
feature.
(Appears only if IP is enabled in Communications Path field.) Selects time delay before the
Communications Module notifies the control panel of a loss of contact with the internet.
Dynamically selects the IP addresses
(Appears only if “No” is selected in Use DHCP field.) Enter NIC IP Address.
(Appears only if “No” is selected in Use DHCP field.) Enter Subnet Address.
(Appears only if “No” is selected in Use DHCP field.) Enter Gateway IP Address
(Appears only if “No” is selected in Use DHCP field.) Enter Domain Name Server IP
Address.
(Appears only if GSM is enabled in Communications Path field.) Selects time delay before
the Communications Module notifies the control panel of a loss of contact with the network.
Allows messages to be sent over GSM in the event that contact with the internet is lost.
Enables daily test of GSM module operation.
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless otherwise noted.
Remote Access (Total Connect) and Multi Mode (PSD) over IP or GSM cannot be enabled in the panel alone.
Availability of this service is controlled via the web-based programming tool on the AlarmNet Direct website. These
features must to be enabled through the AlarmNet Direct website first and transferred to the device.
SCREEN
ACTION
Communicator
5000-100-132-V0
Communicator
1. Select “Communicator”
The System displays the following options:
Communications Path
Primary City Id
Pri Central Station Id
Primary Subscriber Id
Supervision
Old Alarm Time
Remote Acc. IP or GSM
Multi Mode IP or GSM
Use the down T arrow to scroll to the next page of options.
GSM Fault Time
OR
IP Fault Time
2.
Select “Communications Path”. The system scrolls between the following options:
None
IP
GSM
Primary City Id
3.
Select “Primary City Id”. Enter the 2-digit Primary City ID (Decimal).
Options
01-99
Pri Central Station Id
4.
Select “Pri Central Station Id”. Enter the 2-digit Primary Central Station ID (HEX).
Options
01-FE
Primary Subscriber Id
5.
Select “Primary Subscriber Id”. Enter the 4-digit Subscriber Account Number
(Decimal).
Options
0001-9999
Communications Path
None
- 24 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
Supervision
ACTION
6.
Select “Supervision”. The system scrolls between the following options:
24 Hours
None
30 Days
7.
Select “Old Alarm Time”. The system scrolls between the following options:
10 Minutes
15 Minutes
30 Minutes
1 Hour
2 Hours
4 Hours
8 Hours
12 Hours
Use the down T arrow to scroll to the next page of options.
24 Hours
8.
Select “Remote Acc. IP or GSM”. The system toggles between “Disabled” and
“Enabled”.
24 Hours
Old Alarm Time
10 Minutes
Remote Acc. IP or GSM
Disabled
Multi Mode IP or GSM
Disabled
IP Fault Time
00
Use DHCP
Yes
NIC IP Address
9.
If “Remote Access IP or GSM” was enabled in the previous step, the “Multi Mode IP
or GSM” option is displayed. The system scrolls between the following options.
Disabled
Relay Reports
Enhanced Reports
10. Use the down T arrow to scroll to the next page of options. If IP or IP & GSM was
selected in step 2, proceed to step 11. If GSM was selected in step 2, proceed to
step 19.
11. Select “IP Fault Time”. Enter the time delay (in minutes) on the displayed keypad.
Options
00-99
13. Select “Use DHCP”. The system toggles between “Yes” and “No”. If “No” is selected
the system displays four additional options. If “Yes” is selected, skip to step 18.
14. Select “NIC IP Address”. Enter the 4-part address on the displayed keypad.
255.255.255.255
Subnet Mask
15. Select “Subnet Mask”. Enter the 4-part address on the displayed keypad.
255.255.255.255
Gateway IP Address
16. Select “Gateway IP Address”. Enter the 4-part address on the displayed keypad.
255.255.255.255
255.255.255.255
17. Select “DNS Server IP Address”. Enter the 4-part address on the displayed keypad.
18. If “IP” was selected in step 2, select “Save” and then select “OK” when the
“Programming Done” screen appears. Proceed to “Diagnostics” section in order to
register the device.
GSM Fault Time
19. Select “GSM Fault Time”. Enter the time delay (in minutes) on the displayed keypad.
DNS Server IP Address
00
Options
00-99
20. If “GSM” was selected in step 2, select “Save” and then select “OK” when the
“Programming Done” screen appears. Proceed to “Diagnostics” section in order to
register the device.
- 25 -
LYNX Touch Installation and Setup Guide
Programming the Control
Program Zones
The following system options are programmed in this section:
Option
Serial Number
Loop Number
Zone Description 1/2
Device Type
Response Type
Alarm Report
Chime
Supervision
Function
Manually enter device serial number or enroll via RF transmission
Manually enter device loop number or enroll via RF transmission
Enter Zone Descriptors for the device being enrolled
Select the type of device being enrolled
Select the alarm response for the device being enrolled (refer to Zone Response Type Table)
Activate reporting option for the device being enrolled
Enable/disable chime mode for specific device being enrolled (applies to Entry/ Exit, Perimeter,
and Interior Response types only)
Select supervision for device being enrolled
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless otherwise noted.
SCREEN
ACTION
Zones
5000-100-133-V0
Serial Number
Loop Number
Zone Description 1
1. Select “Zones”
The System displays the following options:
1. New
2. Front Door
3. Back Door
4.Window
5. Motion Sensor
6.New
2. Use the down T arrow to scroll to the next page of options. Use the S arrow to return to
the previous page.
7. – 48. New
49. – 56. 4 Button
57. – 64. New
95. Fire
96. Medical
99. Police
3. Select a zone and then select “Edit” or “Add New” to program the next available zone. The
following options are displayed (dependant upon Zone Type):
Serial Number
Loop Number
Zone Description 1
Zone Description 2
Device Type
Response Type
Alarm Report
Chime
Supervision
4. Select an option to display the next programming field.
Serial Number
When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed. The
transmitter serial number and loop number can be enrolled via RF transmission OR manually.
Enroll via RF Learning To enroll the device using RF Learning mode three transmissions
(open/close) of the device will be required. The initial transmission activates the RF Learning
mode and the system will emit a single beep. A second transmission enrolls the serial number
and the system beeps two times and displays “Activate Sensor Again To Confirm”. A third
transmission will confirm the serial number. The system beeps two times and returns to the
Zone programming Screen.
Enroll Manually
Enter the 7-digit serial number printed on the transmitter using the displayed keypad and
select “Done”. The system beeps one time and returns to the Zone programming Screen.
Loop Number
Select “Loop Number” to toggle between 1, 2, 3 and 4. Enter Save.
Zone Description 1
Select “Zone Description 1”. Using the displayed keypad enter Zone Description 1. The
system announces the Zone Description. Enter “Done”, when you are finished. The system
returns to the Zone Programming page.
Zone Description 2
Select “Zone Description 2”. Using the displayed keypad enter Zone Description 2. The
system announces the Zone Description. Enter “Done”, when you are finished. The system
returns to the Zone Programming page.
- 26 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
ACTION
Device Type
Device Type
Select “Device Type”. The system displays the following options (dependant upon the Zone):
New
Door
Window
Motion Sensor
Glass Break
Smoke Detector
Heat Sensor
Carbon Mono. Det.
Use the down T arrow to scroll to the next page of options:
Temperature
Flood
Environmental
Medical
Fire
Police
Other
Response Type
Response Type
1. Select “Response Type”. The system displays the following options (dependant upon the
Zone):
Not Used
Entry Exit 1
Entry Exit 2
Perimeter
Interior Follower
Trouble Alarm
24 Hour Silent
24 Hour Audible
2. Use the down T arrow to scroll to the next page of options. Use the S arrow to return to
the previous page.
24 Hour Auxiliary
Fire No Verification
Interior With Delay
Monitor
Carbon Monoxide
Trouble
Arm Stay
Arm Away
Not Used
Disarm
No Response
Silent Burglary
Resident Monitor
Resident Response
General Monitor
General Response
Fire With Verification
3. Select Response Type and select “Save”. The system will return to the Zone screen
Alarm Report
Yes
Chime
No
Supervision
Supervised
Alarm Report
Note: This field is for Alarms. If Response Type “Trouble” is set up and Alarm Report is set to
“No” the system will still report if Report Alarms was enabled in the Reporter
programming.
Select “Report” to toggle between “No” or “Yes”. Select “Save”.
Chime
Note: Chime only applies to entry/exit, perimeter and interior zone types.
Select “Chime” to toggle between “No” or “Yes”. Select “Save”.
Supervision
Select “Supervision” to scroll between the following options:
Hardwire – Normally Open
Hardwire – Normally Closed
Hardwire – End of Line
RF – Supervised
RF – Unsupervised
After making a Supervision selection, select “Save”.
- 27 -
LYNX Touch Installation and Setup Guide
Programming the Control
Program Keys
The following system options are programmed in this section:
Option
Key Type
User
Serial Number
Zone
Button Key * - Zn *
Function
Select the specific type of key being entered or enrolled
Associates the Key with a specific User
Manually enter key serial number or enroll via RF transmission
Manually enter key zone number (between 49 and 64) or enroll via RF transmission
Associate the selected button with a specific function
* Key number and Zn number are dependant upon the Key Type selected.
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless otherwise noted.
SCREEN
Keys
Key Type
4 Button key
User
ACTION
1. Select “Keys”
The System displays the following options:
Edit
Add New
Delete
2. Select “Add New”.
3. The following options are displayed (dependant upon the “Key Type” selected):
Key Type
User
Serial Number
Zone
Button Key 1 – Zn 49
Button Key 2 – Zn 50
Button Key 3 – Zn 51
Button Key 4 – Zn 52
Button Key 5 – Zn 53
Button Key 6 – Zn 54
Button Key 7 – Zn 55
Button Key 8 – Zn 56
4. Select an option to display the next programming field.
Key Type
Select “Key Type”. The system scrolls between the following:
1 Button key
6 Button key
2 Button key
8 Button key
4 Button key
User
4. Select “User” then select from the following options (or the list of Users that have been
programmed):
Master
Babysitter
Duress
User 3
User 4
User 5
User 6
User 7
Use the down T arrow to scroll to the next page. The system displays options for User 8
through 14.
Note: The Key must be associated with a specific User/User Code in order for it to operate.
Refer to the LYNX Touch User Guide for additional Information regarding User Codes.
Serial Number
Serial Number
When “Serial Number” has been selected “Enter Serial Number or Activate” is displayed. The
transmitter serial number and loop number can be enrolled via RF transmission OR manually.
Enroll via RF Learning To enroll the device using RF Learning mode three transmissions
(open/close) of the device will be required. The initial transmission activates the RF Learning
mode. A second transmission enrolls the serial number and the system beeps two times and
displays “Activate Sensor Again To Confirm”. A third transmission will confirm the serial
number. The system beeps three times and returns to the Zone programming Screen.
Enroll Manually
Enter the 7-digit serial number printed on the transmitter using the displayed keypad and
select “Done”. The system beeps one time and returns to the Zone programming Screen.
Zone
49
Zone
The system displays the next available key Zone number. Select “Zone” to manually enter a
specific Zone Number on the displayed keypad (49-64). If the desired Zone Number is not
available, the system returns to the previous screen.
Select ”Done”. The system returns to the previous screen. Repeat the previous step to enter
another Zone Number.
- 28 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
Button Key * - Zn *
ACTION
Button Key * Zn *
Select the desired Button Key and enter a function for each button key. The system
displays the following options:
Disarm
Arm Away
Arm Stay
No Response
24 Hour Silent
24 Hour Audible
24 Hour Auxiliary
Silent Burglary
Fire No Verification
* Options are the same for each Button/Zone combination.
- 29 -
LYNX Touch Installation and Setup Guide
Programming the Control
Reporter
When Compass service is required and GSM or IP are the only reporting channels: As part of Primary Central
Station programming; the “Phone Type” must be set to any selection other than “None”, the “Communicator Type”
must be set to GSM or IP, as applicable, and must match the compass value; “Phone number” field must be left
blank and an “Account number” must be programmed.
The following system options are programmed in this section:
Option
Prim. or Sec. Central Station
Phone Type
Phone Number
Communicator Type
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Phone 1 or Phone 2
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Report Selection
Options
PBX
Call Wait Cancel
Number of Reports
Alarm Report Delay
Swinger Shutdown
Abort Window
First Offset Report
Report Frequency
Downloader
Phone Answer
Modem Speed
Ans. Machine Defeat
Ring Counter
Callback Number
Flexible Callback
Number
Function
Enroll information pertaining to the Primary and/or Secondary Central Station.
Select the Report Format that will be used to send reports to the Primary or Secondary
Central Station, as applicable.
Enter the Phone Number for the Primary or Secondary Central Station, as applicable.
Select the type of Communications Module that will be used to communicate with the
Primary or Secondary Central Station, as applicable.
Enter the account number for the Primary or Secondary Central Station, as applicable.
Select the primary method for sending Reports to the Primary or Secondary Central
Station, as applicable.
Selects delay between switching between reporting methods. Active if Dynamic Delay
feature has been set to Preferred Telco or Preferred Radio.
Enable All Reports to be sent to the Primary or Secondary Central Station, as applicable.
Enable Alarm Reporting to the Primary or Secondary Central Station, as applicable.
Enable Trouble Reporting to the Primary or Secondary Central Station, as applicable.
Enable Open/Close Reporting to the Primary or Secondary Central Station, as applicable.
Enable Test Reporting to the Primary or Secondary Central Station, as applicable.
Enroll information Primary and/or Secondary telephone numbers for “Follow Me”
Announcements and/or Reminders.
Enter Number for Phone 1 or Phone 2, as applicable.
Enter Primary and/or Secondary telephone numbers for “Follow Me” Announcements
and/or Reminders.
Enable All Reports to be sent to the Phone 1 or Phone 2, as applicable.
Enable Alarm Reporting to the Phone 1 or Phone 2, as applicable.
Enable Trouble Reporting to the Phone 1 or Phone 2, as applicable.
Enable Open/Close Reporting to the Phone 1 or Phone 2, as applicable.
Enable Test Reporting to the Phone 1 or Phone 2, as applicable.
Enable Reporting of Specific Events
Enter the digits required to access an outside line, if applicable
Enter the digits required to cancel call waiting, if applicable
Limit the number of messages sent to the Central Station during an armed period.
(applies to LYNX Touch only)
Disable or select the time delay for alarm reporting (applies to LYNX Touch only)
Select the number of times reports are sent and sounder sounds for non-fire alarms
before the system ignores subsequent alarms (applies to LYNX Touch SIA only)
Select the time delay for alarm reporting (applies to LYNX Touch SIA only)
Select the time for the first test report following power-up/programming or downloading
Select the test report frequency
Enable or disable to allow control to answer incoming phone line.
(Future Use)
Enable to defeat answering machine mode. (Active if Phone Answer is enabled.)
Enter the number of rings before control picks up phone line. (Active if Ans. Machine
Defeat is not enabled.)
Enter the phone number the control will use to call back the downloading computer.
(Active if Phone Answer is enabled.)
Allows Download operator to temporarily change the callback number by the number of
digits selected. Active if Phone Answer is enabled
Enter the number of flexible callback numbers that will be used. Active if Flexible Callback
is enabled.
- 30 -
LYNX Touch Installation and Setup Guide
Programming the Control
Notes: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless
otherwise noted.
When GSM is used as the Primary Communications channel for any Total Connect service, the GSM
Radio must be selected as the Primary Reporting Path (Preferred Radio).
SCREEN
Reporter
Primary
Central Station
Phone Type
Contact Id: 4 Digit
Phone Number
Communicator Type
None
ACTION
Select “Reporter”
The System displays the following options:
Primary Central Station
Secondary Central Station
Phone 1
Phone 2
Report Selection
Options
Downloader
Select “Primary Central Station”. The System displays the following options:
Phone Type
Communicator Type
Select “Phone Type”. The System scrolls though the following options:
None
Contact Id: 4 Digit
Contact Id: 10 Digit
SIA
If any option other than “None” is selected in “Phone Type” The “Phone Number” option will
be displayed. Select “Phone Number”. Enter the Primary Central Station Phone Number on
the displayed keypad.
Select “Communicator Type”. The System scrolls though the following options:
None
GSM
IP
Note: The system will display the communications (GSM or IP) path that was selected in
Communications Programming. The Communication Path selection can be enabled for either
Primary Central Station or Secondary Central Station but not both. If it is enabled in one it will
not be available for the other Central Station.
Account Number
FFFF
Dynamic Priority
Redundant Reports
Dynamic Delay
30 Seconds
If any option other than “None” is selected in “Phone Type” The “Account Number” option
will be displayed. Select “Account Number”. Enter the Primary Central Station Account
Number on the displayed keypad.
If any option other than “None” is selected in “Communicator Type” The “Dynamic Priority”
option will be displayed. “Select “Dynamic Priority”. The system scrolls between “Redundant
Reports”, “Preferred Telco” and Preferred Radio”.
If any option other than “Redundant Reports” is selected in “Dynamic Priority” The “Dynamic
Delay” option will be displayed. “Select “Dynamic Delay”. The system scrolls between “15
Seconds”, “30 Seconds”, “60 Seconds” and “90 Seconds”.
Note: If GSM is selected as the primary reporting channel Dynamic Delay should be set to minimum
of 60 seconds.
Report All
Press to Report All
Select “Report All”. The System toggles between “Press to Report All” and “Report All Set”.
If “Report All” is selected all reporting options will be “Enabled”. Select the “Save” key to
return to the Reporter options screen.
Report Alarms
Disabled
Select “Report Alarms”. The System toggles between “Disabled” and “Enabled”.
SIA: The LYNX Touch SIA default is “Enabled”.
Report Troubles
Disabled
Select “Report Troubles”. The System toggles between “Disabled” and “Enabled”.
SIA: The LYNX Touch SIA default is “Enabled”.
Report Open/Close
Disabled
Select “Open/Close”. The System toggles between “Disabled” and “Enabled”.
Report Tests
Disabled
Select “Report Tests”. The System toggles between “Disabled” and “Enabled”.
Secondary
Central Station
Select “Secondary Central Station”. The System displays the following options:
Phone Type
Communicator Type
- 31 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
Phone Type
None
Communicator Type
None
ACTION
Select “Phone Type”. The System displays the following options:
None
Contact Id: 4 Digit
Contact Id: 10 Digit
SIA
Select “Communicator Type”. The System displays the following options:
None
GSM or IP
Note: The system will display the communications path (GSM or IP) selected in Communications
Programming. The path can be enabled for either primary Central Station or Secondary Central
Station but not both. If it is enabled in one it will not be available for the other Central Station.
Phone Number
Account Number
FFFF
Dynamic Priority
Redundant Reports
If any option other than “None” is selected in “Phone Type”, the “Phone Number” option will
be displayed. Select “Phone Number”. Enter the Secondary Central Station Phone Number
on the displayed keypad.
If any option other than “None” is selected in “Phone Type” The “Account Number” option will
be displayed. Select “Account Number”. Enter the Secondary Central Station Account
Number on the displayed keypad.
If any option other than “None” is selected in “Communicator Type” The “Dynamic Priority”
option will be displayed. “Select “Dynamic Priority”. The system scrolls between “Redundant
Reports”, “Preferred Telco” and Preferred Radio”.
30 Seconds
If any option other than “Redundant Reports” is selected in “Dynamic Priority” The “Dynamic
Delay” option will be displayed. “Select “Dynamic Delay”. The system scrolls between “15
Seconds”, “30 Seconds”, “60 Seconds” and “90 Seconds”.
Note: If GSM is selected as the primary reporting channel Dynamic Delay should be set to
minimum of 60 seconds.
Report All
Press to Report All
Select “Report All”. The System toggles between “Press to Report All” and “Report All Set”. If
“Report All” is selected all reporting options will be “Enabled”. Select the “Save” key to return
to the Reporter options screen.
Dynamic Delay
Report Alarms
Disabled
Select “Report Alarms”. The System toggles between “Disabled” and “Enabled”.
Report Troubles
Disabled
Select “Report Troubles”. The System toggles between “Disabled” and “Enabled”.
Report Open/Close
Disabled
Select “Open/Close”. The System toggles between “Disabled” and “Enabled”.
Report Tests
Disabled
Select “Report Tests”. The System toggles between “Disabled” and “Enabled”.
Phone 1
Phone Type
None
Phone Number
Report All
Press to Report All
Select “Phone 1” to program the “Follow Me” Reminder telephone number 1
Select “Phone Type”. The System toggles between “None” and “Follow Me”.
Select “Phone Number”. Enter the “Follow Me” Phone Number 1 on the displayed keypad.
Select “Report All”. The System toggles between “Press to Report All” and “Report All Set”. If
“Report All” is selected all reporting options will be “Enabled”. Select the “Save” key to return
to the Reporter options screen.
Report Alarms
Disabled
Select “Report Alarms”. The System toggles between “Disabled” and “Enabled”.
Report Troubles
Disabled
Select “Report Troubles”. The System toggles between “Disabled” and “Enabled”.
- 32 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
ACTION
Report Open/Close
Disabled
Select “Open/Close”. The System toggles between “Disabled” and “Enabled”.
Report Tests
Disabled
Select “Report Tests”. The System toggles between “Disabled” and “Enabled”.
Phone 2
Phone Type
None
Select “Phone 2” to program the “Follow Me” Reminder telephone number 2.
Select “Phone Type”. The System toggles between “None” and “Follow Me”.
Phone Number
Select “Phone Number”. Enter the “Follow Me” Phone Number 2 on the displayed keypad.
Report All
Press to Report All
Select “Report All”. The System toggles between “Press to Report All” and “Report All Set”.
If “Report All” is selected all reporting options will be “Enabled”. Select the “Save” key to
return to the Reporter options screen.
Report Alarms
Disabled
Select “Report Alarms”. The System toggles between “Disabled” and “Enabled”.
Report Troubles
Disabled
Select “Report Troubles”. The System toggles between “Disabled” and “Enabled”.
Report Open/Close
Disabled
Select “Open/Close”. The System toggles between “Disabled” and “Enabled”.
Report Tests
Disabled
Select “Report Tests”. The System toggles between “Disabled” and “Enabled”.
Report Selection
Select “Report Selection”. The System displays the following options:
Arm Away
Arm Stay
Disarm
Exit Error
Recent Closing
Event Log Full
Trouble
Trouble Restore
Use the down T arrow to scroll to the next page of options.
Alarm Restore
Alarm Cancel
Test
Test Restore
Bypass
Bypass Restore
AC Loss
AC Loss Restore
Use the down T arrow to scroll to the next page of options.
Low Battery
Low Battery Restore
RF Low Battery
RF Low Battery Restore
Arm Away
Enabled
Select “Arm Away”. The System toggles between “Disabled” and “Enabled”.
Arm Stay
Enabled
Select “Arm Stay”. The System toggles between “Disabled” and “Enabled”.
Disarm
Enabled
Select “Disarm”. The System toggles between “Disabled” and “Enabled”.
Exit Error
Enabled
Select “Exit Error”. The System toggles between “Disabled” and “Enabled”.
Recent Closing
Enabled
Select “Recent Closing”. The System toggles between “Disabled” and “Enabled”.
Note: In the LYNX Touch SIA control, this field is always “Enabled”.
Event Log Full
Enabled
Select “Event Log Full”. The System toggles between “Disabled” and “Enabled”.
- 33 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
Trouble
Enabled
Trouble Restore
Enabled
ACTION
Select “Trouble”. The System toggles between “Disabled” and “Enabled”.
Select “Trouble Restore”. The System toggles between “Disabled” and “Enabled”.
Alarm Restore
Enabled
Select “Alarm Restore”. The System toggles between “Disabled” and “Enabled”.
Alarm Cancel
Enabled
Select “Alarm Cancel”. The System toggles between “Disabled” and “Enabled”.
Test
Enabled
Test Restore
Enabled
Bypass
Enabled
Bypass Restore
Enabled
AC Loss
Enabled
AC Loss Restore
Enabled
Low Battery
Enabled
Low Battery Restore
Enabled
RF Low Battery
Enabled
RF Low Battery Restore
Enabled
Options
PBX
Call Wait Cancel
Number of Reports
Unlimited
Select “Test”. The System toggles between “Disabled” and “Enabled”.
Select “Test Restore”. The System toggles between “Disabled” and “Enabled”.
Select “Bypass”. The System toggles between “Disabled” and “Enabled”.
Select “Bypass Restore”. The System toggles between “Disabled” and “Enabled”.
Select “AC Loss”. The System toggles between “Disabled” and “Enabled”.
Select “AC Loss Restore”. The System toggles between “Disabled” and “Enabled”.
Select “Low Battery”. The System toggles between “Disabled” and “Enabled”.
Select “Low Battery Restore”. The System toggles between “Disabled” and “Enabled”.
Select “RF Low Battery”. The System toggles between “Disabled” and “Enabled”.
Select “RF Low Battery Restore”. The System toggles between “Disabled” and “Enabled”.
Select “Options”. The System displays the following options:
LYNX Touch Control
PBX
Call Wait Cancel
Number of Reports
Alarm Report Delay
First Report Offset
Report Frequency
LYNX Touch SIA Control
PBX
Call Wait Cancel
First Report Offset
Swinger Shutdown
Abort Window
Report Frequency
Select “PBX”, and enter PBX Prefix on the displayed keypad.
Select “Call Wait Cancel”, and enter Call Wait Cancel Prefix on the displayed keypad
Note: This field applies only to the LYNX Touch control.
Select “Number of Reports”, the system toggles between “Unlimited” and “10 Reports”.
- 34 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
Alarm Report Delay
No Delay
Swinger Shutdown
2 Reports
Abort Window
30sec
First Report Offset
6 Hrs
Report Frequency
Never
Downloader
Phone Answer
ACTION
Note: This field applies only to the LYNX Touch control.
Select “Alarm Report Delays”. The System scrolls between the following options:
15sec
30sec
45sec
No delay
Note: This field applies only to the LYNX Touch SIA control.
Select “Swinger Shutdown”, the system toggles between “1 Report” and “2 Reports”.
Note: This field applies only to the LYNX Touch SIA control.
Select “Abort Window”. The System scrolls between the following options:
15sec
30sec
45sec
SIA The burglary abort window must be set to a minimum of 15 seconds. The sum of the
burglary abort window and the entry delays should not exceed 1 minute.
Note: The LYNX Touch SIA control validates the data entered in this field. If the selection is
not valid the control will emit a single long beep indicating that the selection has been
rejected. The control replaces the selection with the default value “30sec.
Select “First Report Offset” for the Test Report. The System scrolls between the following
options:
6 Hrs
12 Hrs
18 Hrs
24 Hrs
Select “Report Frequency” for the Test Report. The System scrolls between the following
options:
Never
Every Day
Every 7 Days
Every 30 Days
Select “Downloader”. The System displays the following options:
Phone Answer
Modem Speed
Ans.Machine Defeat
Callback Number
Ring Counter
Flexible Callback
Number
Select “Phone Answer”, the system toggles between “Yes” and “No”.
Yes
Modem Speed
(Future Use)
Slow
Ans. Machine Defeat
Select “Ans. Machine Defeat”, the system toggles between “Yes” and “No”.
Yes
Callback Number
Ring Counter
Flexible Callback
Select “Callback Number” and enter callback number on the displayed keypad.
This option only appears if Answering Machine defeat is set to “No”. Enter ring counter (1 –
14 rings) on the displayed keypad.
Select “Flexible Callback”, the system toggles between “Yes” and “No”.
No
Number
This option only appears if “Flexible Callback” is set to “Yes”. The system scrolls between
options 1, 2 and 3.
- 35 -
LYNX Touch Installation and Setup Guide
Programming the Control
Sounder
The following system options are programmed in this section:
Option
Burglary Alarm Sound
Burglary Alarm Timeout
Fire Bell Timeout
Arm Confirm
Alarm Options
Function
Switches the full 110 dB alarm sound for burglary On/Off.
Select the time for timeout of the Burglary Alarm sounder.
Select the time for timeout of the Fire Alarm sounder.
Enable sounder “ding” when system is armed via the selected RF device.
Select a limit for the number of times an alarm can sound for a specific zone.
Note: This option does not apply to the LYNX Touch SIA control.
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless otherwise noted.
SCREEN
Sounder
Burglary Alarm Sound
ACTION
Select “Sounder”
The System displays the following options:
Burglary Alarm Sound
Burglary Bell Timeout
Fire Bell Timeout
Arm Confirm
Alarm Options
Select “Burglary Alarm Sound”. The System toggles between Yes* and No:
Yes
Burglary Bell Timeout
4 Minutes
Fire Bell Timeout
4 Minutes
Arm Confirm
None
Alarm Options
Unlimited
Select “Burglary Bell Timeout”. The System scrolls between the following options:
No
4 Minutes
8 Minutes
12 Minutes
16 Minutes
Select “Fire Bell Timeout”. The System scrolls between the following options:
No
4 Minutes
8 Minutes
12 Minutes
16 Minutes
Note: This option does not apply to the LYNX Touch Control.
Select “Arm Confirm”. The System scrolls between the following options:
None
All RF
RF Key Fob
RF Keypad
Select “Alarm Options”. The System scrolls between the following options:
Unlimited
10
Select “Save”.
- 36 -
LYNX Touch Installation and Setup Guide
Programming the Control
System Settings
The following system options are programmed in this section:
Option
Function
Entry Delay1/Entry Delay 2
Selects an Entry Delay time in seconds. The system will wait the time entered before
sounding alarm upon entering if system is not disarmed.
Note: The Default values differ for the LYNX Touch and LYNX Touch SIA controls.
Exit Delay
Selects an Exit Delay time in seconds for both Entry Delay 1 and 2 Zone Types. The
system will wait the time entered before sounding an alarm if the exit door is left open after
the system has been armed.
Note: The Default values differ for the LYNX Touch and LYNX Touch SIA controls.
Backlight Timeout
Enable or disable display backlight turnoff after 30 seconds.
Quick Arm
Enables or disables Quick Arm Mode. If enabled, security code is not required to arm the
system. The user simply presses and holds down the AWAY button or ICON and then
selects the ARM button on the displayed keypad to arm the system.
Quick Exit
Enables or disables Quick Exit Mode. If enabled allows the user restart the exit delay to
allow entry or exit when the system is armed
Restart Exit Time
Enables or disables Restart Exit Time Mode. This option allows the control to restart the
exit delay time after arming in STAY mode by entering the User Code and pressing the
STAY key (if quick arming is disabled) or by pressing the STAY key (if quick arming is
enabled). This option also enables automatic exit delay reset, which resets exit delay if the
entry/exit door is re-opened and closed before exit delay time expires after arming.
Force Bypass
Enables or disables Force Bypass Mode. All zones bypassed by this function will be
displayed after the bypass is initiated. The Fire and CO Zones are not bypassed in the
LYNX Touch.
Exit Warning
Enables or disables Exit Warning sound. Audible Exit Warning sound consists of slow
continuous beeps until last 5 seconds, when it changes to fast beeps. The warning sound
will end at the termination of exit delay.
Note: This field is not programmable in the LYNX Touch SIA and is always enabled.
Auto Stay Arming
Enables or disables Auto Stay Arming Mode. If this feature is enabled and the control panel
has been armed “Armed Away” at the LYNX Touch keypad or RF keypad, the system will
switch to the “Armed Stay” mode if the Exit Time has expired and no exit has been made.
Lack of Usage Notify
Enables or disables Lack of Usage Notification feature. If enabled, notifies the central
station if an end user is not operating their security system by sending a System Inactivity
report 654. The report will be sent only to the Primary phone number and only if Contact
ID® format was selected.
Power-Up in Previous
Enables or disables Power-Up in Previous Mode feature. When the system powers up
armed, an alarm will occur 1 minute after arming if a zone is faulted. For the LYNX Touch
control any bypassed zones will be unbypassed. For the LYNX Touch SIA any bypassed
zones will remain bypassed.
Display Alarm Cancel
Enables or disables display of Cancelled Alarm.
Display Exit Time
Enables or disables display of Exit Time.
Cross Zone Delay
Sets the maximum amount of time in which two zones must be tripped in an armed system
to send an alarm message to the Central Station. If only one cross zone is tripped during
this time, a trouble message (CID code 380) for that zone is sent to the Central Station.
Cross Zone 1/Cross Zone 2
Select the zones that will be used for Cross Zoning
- 37 -
LYNX Touch Installation and Setup Guide
Programming the Control
Note: If applicable, preprogrammed defaults for the LYNX Touch Control are shown on the screen unless otherwise noted.
SCREEN
System Settings
Entry Delay 1
30 Seconds
ACTION
Select “System Settings”
The System displays the following options:
Entry Delay 1
Entry Delay 2
Exit Delay
Backlight Timeout
Quick Arm
Quick Exit
Restart Exit Time
Force Bypass
Exit Warning
Auto Stay Arming
Use the down T arrow to scroll to the next page of options. Use the S arrow to return to
the previous page:
Lack of Usage Notify
Power-Up In Previous
Display Alarm Cancel
Display Exit Time
Cross Zone Delay
Cross Zone 1
Cross Zone 2
Select “Entry Delay 1”. The System scrolls between the following options:
LYNX Touch LYNX Touch SIA
None
30 Seconds
15 Seconds
45 Seconds
30 Seconds
60 Seconds
45 Seconds
90 Seconds
60 Seconds
2 Minutes
90 Seconds
3 Minutes
2 Minutes
4 Minutes
UL installations: The Entry Delay must be set for a maximum of 45 seconds
SIA: The Entry delay must be set to a minimum of 30 seconds. The sum of entry delay 1 and
the burglary abort window should not exceed 1 minute.
Entry Delay 2
60 Seconds
Select “Entry Delay 2”. The System scrolls between the following options:
LYNX Touch LYNX Touch SIA
None
30 Seconds
15 Seconds
45 Seconds
30 Seconds
60 Seconds
45 Seconds
90 Seconds
60 Seconds
2 Minutes
90 Seconds
3 Minutes
2 Minutes
4 Minutes
UL installations: The Entry Delay must be set for a maximum of 45 seconds
SIA: The Entry delay must be set to a minimum of 30 seconds. The sum of entry delay 2 and
the burglary abort window should not exceed 1 minute. The LYNX Touch SIA default is
“60 Seconds”.
Exit Delay
60 Seconds
Select “Exit Delay”. The System toggles between the following options:
LYNX Touch LYNX Touch SIA
None
45 Seconds
15 Seconds
60 Seconds
30 Seconds
90 Seconds
45 Seconds
2 Minutes
60 Seconds
90 Seconds
2 Minutes
UL installations: Exit Delay must be set for a maximum of 60 seconds
SIA: The Exit Delay must be set to a minimum of 45 seconds.
Backlight Timeout
Select “Backlight Timeout”. The System toggles between No and 30 Seconds.
No
Quick Arm
Select “Quick Arm”. The System toggles between Yes and No.
Yes
- 38 -
LYNX Touch Installation and Setup Guide
Programming the Control
SCREEN
Quick Exit
ACTION
Select “Quick Exit”. The System toggles between Yes and No.
Yes
Restart Exit Time
No
Force Bypass
No
Exit Warning
No
Auto Stay Arming
No
Lack of Usage Notify
Disabled
Power-Up In Previous
Yes
Select “Restart Exit Time”. The System toggles between Yes and No.
SIA: The LYNX Touch SIA default is “Yes”.
Select “Force Bypass”. The System toggles between Yes and No.
UL installations: must be NO (no forced bypass)
Select “Exit Warning”. The System toggles between Yes and No.
Note: This option is not selectable in the LYNX Touch SIA control and is always
enabled.
Select “Auto Stay Arming”. The System toggles between Yes and No.
SIA: The LYNX Touch SIA default is “Yes”.
Select “Lack of Usage Notify”. The System scrolls between the following options:
Disabled
1 Day
7 Days
27 Days
90 Days
180 Days
365 Days
Select “Power-Up In Previous”. The System toggles between Yes and No.
Note: If the previous state was Armed Away or Stay, the system will not respond to sensor changes for
1 minute. This allows time for sensors such as PIRs to stabilize.
UL installations: must be 1 (power up in previous state)
Display Alarm Cancel
Select “Display Alarm Cancel”. The System toggles between Yes and No.
No
Display Exit Time
Select “Display Exit Time”. The System toggles between Yes and No.
Yes
Cross Zone Delay
3 Minutes
Cross Zone 1
Disabled
Cross Zone 2
Disabled
Select “Cross Zone Delay”. The System toggles between the following:
None
30 Seconds
1 Minute
90 Seconds
2 Minutes
3 Minutes
4 Minutes
Select “Cross Zone 1”. The System toggles between the following:
Disabled
Note: If Cross Zone Delay is enabled the system will display the zones that are programmed with the
following Zone Types: Day/Night, Interior Follower and perimeter.
Select “Cross Zone 2”. The System toggles between the following:
Disabled
Note: If Cross Zone Delay is enabled the system will display the zones that are programmed with the
following Zone Types: Day/Night, Interior Follower and perimeter.
- 39 -
LYNX Touch Installation and Setup Guide
Programming the Control
Communications Diagnostics
Communications Status – The system provides a status of the IP or GSM communications paths and
performs a self-test of the AES encryption algorithm as follows:
Message
GSM:
Encryption:
Alarmnet Registration:
Meaning
OK
Fault Reported!
Not Connected
Not Registered!
No Physical Link
AES Passed!
AES Failed!
No Encryption!
Registered
Not Registered
Normal; No fault. (IP or GSM)
No network connectivity and fault time has expired. (IP or GSM)
No network connectivity over IP and fault time has NOT yet expired.
No network connectivity over GSM and fault time has NOT yet expired.
No network connectivity over IP and fault time is set to 0.
Test successful.
Test failed.
No encryption algorithm set.
Communication Device is Registered with AlarmNet.
Communication Device is not Registered with AlarmNet.
Ethernet Information – Displays IP information, if IP communication path is enabled.
Physical Link:
DHCP:
Indicates status of the physical connection to the internet.
DHCP (Dynamic Host Configuration Protocol) indicated server is performing satisfactorily.
NIC IP Address:
Displays the IP address assigned to this device
Subnet Mask:
Displays the 32-bit address mask used to indicate the portion (bits) of the IP address that is
being used for the subnet address.
Displays the IP address assigned to the Gateway.
Displays the IP address assigned to the DNS (Domain Name System) server.
Gateway IP Address:
DNS Server IP Address:
Message
Physical Link
DHCP
Meaning
10 Mbps or 100 Mbps
Bad
OK
Bad
Off
Link speed of physical connection
No physical connection
DHCP address resolved
DHCP address not resolved
DHCP disabled
GSM Information – Displays GSM information if GSM communication path is enabled.
Status
GSM Registered
GSM Not Registered
Message
Cell Registration:
Home
Roaming
Primary RSSI: -xxdBm*
GPRS: Yes
No
Country: xxx
Network: xxx
LAC xxxxx
Cell: xxxx
Base Station: xx
Channel: xxx
Second Site RSSI: -xxdBm*
Searching For Coverage!
SIM Error!
Cell Registration: SIM Not Active
Cell Registration: Not Registered
Meaning
Registered Home
Registered Roaming
Primary Site RSSI level in dBm
GPRS Service availability
GPRS is not available
Country Code
Network Code
Local Area Code
Base Station ID
Base Station Antenna Sector
Control Channel in use
Secondary Site RSSI level in dBm
Searching for cell network.
No SIM card present or SIM card faulty
SIM is not activated
Not registered with cell network
* RSSI = Communications Module’s Signal Level. Displayed in dBm, where:
xx = -01 to -93 Indicates Good signal level
xx = -94 to -95 Indicates Poor signal level. Unit should be relocated for better signal level.
xx = -96 (and lower) Indicates fail signal level. Move unit for better signal level. If “FAIL” condition persists, do not install.
- 40 -
LYNX Touch Installation and Setup Guide
Programming the Control
Communications ID Numbers – Displays programmed SIM card information
Message
MAC:
MAC CRC:
SCID:*
IMEI:*
xxxxxxxxxxxx
xxxx
xxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxx
Meaning
MAC Address indicates the unique identification number
MAC CRC number
Displays the ID number assigned to the installed SIM card (SCID)
Displays the ID number assigned to the installed GSM module.
* Displayed if GSM communication path is enabled.
Test Communications – Performs network diagnostics and sends test alarms to AlarmNet. The following
tests are available depending on the type of communications module installed.
Test Ethernet
This test is available if IP communication path is enabled. The network diagnostic process tests the integrity of the links
between the LYNX Touch and the various connection points of AlarmNet Control that are known as “Redirectors”. If a
physical link is detected and is ready, the following diagnostics are performed.
Testing Gateway…
Traces the connection to the Gateway and displays the following:
Testing Gateway – Successful!
A successful trace to Gateway. OR
Testing Gateway – Failed!
Failed to reach Gateway.
Testing Redirector * Sequentially traces the connection to Redirector 1, 2 and 3 at AlarmNet Control. The following will be
displayed.
Redirector * – Service OK
Service at AlarmNet Control on Redirector 1, 2 or 3 is functioning. OR
Redirector * – Failed
Error occurred on Redirector 1, 2 or 3.
* = Number of the director being tested is displayed
A summary of the tests is displayed after Redirector 3 is tested. The example shows that the tests of all three
connection points, or Redirectors, were successful. If an error occurred at any point, the summary will display
“Failed” next to the faulty Redirector.
Redirector 1 – Service OK
Redirector 2 – Service OK
Redirector 3 – Service OK
If no physical link is detected, the test is aborted and one of the following is displayed:
No Physical Link
No physical link is detected.
Link Not Ready
There is a link but it is not ready (address not resolved).
Send Any
If both IP and GSM communication paths are enabled and the LYNX Touch is registered, a Test alarm is sent over IP path. If
that is not successful, it sends the alarm over GSM path and the following message is displayed: Test Message Sent
If the device is not registered, the following is displayed: Test Message Failed – Not Registered
Send GSM Message
If GSM communication path is enabled and the LYNX Touch is registered, a Test alarm to AlarmNet over the GSM path. The
following message is displayed: Test Message Sent
If the device is not registered, the following message is displayed: Test Message Failed – Not Registered
Send Ethernet Message
If IP communication path is enabled and the LYNX Touch is registered, a Test alarm to AlarmNet over the IP path. The
following message is displayed: Test Message Sent
If the device is not registered, the following message is displayed: Test Message Failed – Not Registered
Setup Communication – Performs registration of the LYNX Touch and its associated communication
module with AlarmNet updates configuration files or reset factory defaults.
Registering the LYNX Touch
Once the LYNX Touch is initialized and a communications module is programmed, it must be registered to
enable the account. Upon completion of the registration process, the LYNX Touch transmits a registration
message and receives a registration validation indicating that the account is now enabled. Wait for the
“Registration Success” message to appear, regardless of which registration method is used.
You can register the communications module by one of the following methods:
• Through the AlarmNet Direct website
• By Phone
• Through the LYNX Touch Diagnostics
- 41 -
LYNX Touch Installation and Setup Guide
Programming the Control
Register through AlarmNet Direct Website
If you have programmed the communications module through AlarmNet Direct, you must then transfer the
data to the module, and register the module.
To do this, please go to: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx.
Log in and follow the on-screen prompts.
If you are not signed up for this service, click on “Dealer Signup” from the login screen to gain access to the
Honeywell web-based programming.
Dealer Sign-Up Direct Link: https://services.alarmnet.com/AlarmNetDirectP_Sign-Up.
You will be instructed how to proceed upon completing the sign-up form. Only one sign-up per dealer is
required. Once an initial user is established, additional logins may be created by that user.
Please have the following information available when programming the device:
1. Primary City ID (two-digit number)
2. Primary Central Station ID (two-digit hexadecimal number)
3. Primary Subscriber ID (four-digit number)
4. MAC ID and MAC CRC number (located on outside of box and on label inside module – location to be
confirmed).
Once module is registered, you may log out of the AlarmNet Direct website.
Register by Phone
You can register the module by calling the AlarmNet Technical Assistance Center (TAC) at 1-800-222-6525.
You will need the following information:
• MAC number (found on the label).
• Subscriber information (provided by the central station), including a city code, CSID, and a subscriber
ID.
• When instructed to do so, select Register Device in the LYNX Touch Diagnostics to complete the
registration.
Register through LYNX Touch Diagnostics
You can register the module using the LYNX Touch Diagnostics by the following the following procedure.
SCREEN
Comm. Diagnostics
Setup
Communication
ACTION
1. Select “Comm. Diagnostics” The System displays the following options depending upon
the communication device that is installed:
Communication
Ethernet
GSM
Status
Information
Information
Communication
Test
Setup
ID Numbers
Communication
Communication
2. Select “Setup Communication”. The System advances to the Registration screen and
the following options are displayed:
Register
Register Device
Device
With PIN
Update
Factory
Server
Defaults
3. Select “Register Device”. The registration message is sent and the unit waits
for the acknowledgement. (Refer to the table below for applicable
registration messages.)
Note: Register Device can be cancelled by selecting “Cancel”. The registration process is
aborted and the message Registration Cancelled! is displayed.
- 42 -
LYNX Touch Installation and Setup Guide
Programming the Control
During the registration process the following messages may be displayed:
Message
Getting Configuration File…
Registering…
Registration Successful!
Registering – Try Later!
Registration Failed!
Invalid Configuration!
Timed Out.
Central Station Database Full.
Primary Sub ID Bad.
Primary ID – Need PIN.
Account Disabled.
Meaning
The configuration file is obtained from AlarmNet if the module was programmed through
AlarmNet Direct or a previously programmed module was defaulted.
The registration message is sent and the unit is waiting for the acknowledgement.
The module is registered and is now in full service and available for alarm reporting to the
central station.
Error Message indicates the module is busy.
Error message followed by one of the messages below:
Indicates the configuration is invalid.
Displayed if no response to the registration request is received.
Indicates CS database has more than 1000 subscribers.
Indicates the city, central station, or customer number for the labeled account is not
accepted. The ID information was either entered incorrectly, or the central station failed to
pre-authorize programmed ID numbers with AlarmNet customer service.
Indicates the city, central station, or customer number for the labeled account is not
accepted. The ID information was either entered incorrectly, or the central station failed to
pre-authorize programmed ID numbers with AlarmNet customer service. See the Register
Device With PIN section.
Displayed if the account is disabled in AlarmNet.
Register Device With PIN
This procedure is used to replace one LYNX Touch module with another.
SCREEN
Comm. Diagnostics
Setup
Communication
ACTION
1. Select “Comm. Diagnostics” The System displays the following options depending upon
the communication device that is installed:
Communication
Ethernet
GSM
Status
Information
Information
Communication
Test
Setup
ID Numbers
Communication
Communication
2. Select “Setup Communication”. The System advances to the Registration screen and
the following options are displayed:
Register
Register Device
Device
With PIN
Update
Factory
Server
Defaults
3. Select “Register Device With PIN”. Enter a 4-digit alphanumeric PIN number
(provided by your central station, your dealer or an authorized AlarmNet
representative) on the displayed keypad then select “Done”. (Refer to the
table below for applicable registration messages.)
Note: Register Device With PIN can be cancelled by selecting “Cancel”. The registration
process is aborted and the message Registration Cancelled! is displayed.
During the registration process the following messages may be displayed:
Message
Registering…
Registration Successful!
Registering – Try Later!
Registration Failed!
Invalid Configuration!
Timed Out.
Primary ID – Need PIN.
Meaning
The registration message is sent and the unit is waiting for the acknowledgement.
The PIN number is valid and module is registered and is now in full service and available
for alarm reporting to the central station. The old module is unregistered. Additionally,
AlarmNet sends a substitution alarm to the central station.
Error Message indicates the module is busy.
Error message followed by one of the messages below:
Indicates the configuration is invalid.
Displayed if no response to the registration request is received.
Indicates PIN that was entered is invalid.
- 43 -
LYNX Touch Installation and Setup Guide
Programming the Control
Update Server
This procedure is used to upload the Configuration File to the Server.
SCREEN
Comm. Diagnostics
Setup
Communication
Yes
ACTION
1. Select “Comm. Diagnostics” The System displays the following options depending upon
the communication device that is installed:
Communication
Ethernet
GSM
Status
Information
Information
Communication
Test
Setup
ID Numbers
Communication
Communication
2. Select “Setup Communication”. The System advances to the Registration screen and
the following options are displayed:
Register
Register Device
Device
With PIN
Update
Factory
Server
Defaults
3. Select “Update Server” and select “Yes” when the confirmation screen appears. The
device uploads its entire configuration file to the server. Selecting “No” will cancel the
operation. (Refer to the table below for applicable registration messages.)
During the upload process the following messages may be displayed:
Message
Updating Root File…
Programming Done
Updating Configuration – Try Later!
Cannot Upload – Try Later!
Update Root File – Failed!
Meaning
The root file is being uploaded.
Indicates the root file has been successfully uploaded.
Error message indicates the module is busy
Error message indicates the communication path(s) is not available.
Error message indicates an error while uploading root file..
- 44 -
LYNX Touch Installation and Setup Guide
Programming the Control
Factory Defaults
This procedure resets the programming options to factory-default values.
SCREEN
Comm. Diagnostics
Setup
Communication
ACTION
1. Select “Comm. Diagnostics” The System displays the following options depending upon
the communication device that is installed:
Communication
Ethernet
GSM
Status
Information
Information
Communication
Test
Setup
ID Numbers
Communication
Communication
2. Select “Setup Communication”. The System advances to the Registration screen and
the following options are displayed:
Register
Register Device
Device
With PIN
Update
Factory
Server
Defaults
3. Select “Factory Defaults” and select “Yes” when the confirmation screen appears. The
device is reset to factory default values. Selecting “No” will cancel the operation. (Refer
to the table below for applicable registration messages.)
The following messages may be displayed:
Message
Default Configuration – Successful!
Default Configuration Failed –
Access Denied
Default Configuration – Try Later!
Meaning
Indicates all programmed values are reset to the original factory settings.
Error message indicates the device does not have local programming access.
Error message indicates the module is busy.
- 45 -
LYNX Touch Installation and Setup Guide
Remote Programming/Control (Downloading)
General Information
The control panel can be remotely programmed from an IBM-compatible Personal Computer (PC), Compass
Downloader, a HAYES compatible Modem or via a capable GSM or IP Communications Module. When
connected to the COMPASS Downloader – “SERVICE UPDATE” appears on touch screen.
UL
Downloading may only be performed if a technician is at the site.
Multiple security levels protect remote programming against compromise by attempts to defeat the system.
1. Security Code Handshake: A download ID code is verified for authenticity before connection is
established.
2. Site-Initiated Remote Programming: The installer initiates downloading by selecting the “Initiate
Download” button on the Installer programming screen.
3. Station-Initiated Remote Programming: The operator calls the site from your office to initiate the
download call. The Control hangs up and then calls back the PC via the preprogrammed telephone
number. The unit can then be uploaded, downloaded, or controlled from your office.
4. Data Encryption: Data passed between the PC and the Control is encrypted for security so that it is
very difficult for a foreign device tapped into the phone line to take over communication and substitute
system-compromising information.
Equipment required to download to a system at the premises
• Compass Downloader for Windows (at revision level supporting LYNX Touch).
Flexible Callback: If enabled in Installer Programming, the download operator can temporarily change
the last 1, 2, or 3 digits (depending on selection) of the call back number. This allows the control to call back
a computer other than the one programmed, which may be helpful at times of high computer traffic.
Remote Programming Information
If using Remote Programming, the LYNX Touch must be connected to the telephone line, GSM Cellular or
to the Internet, as applicable.
The downloading system can perform many functions when in communication with the Control. Besides
uploading and downloading, the status of the system can be observed and various commands can be
initiated, as follows:
• Arm the system in the away mode; disarm the system.
• Bypass a zone.
• Force the system to accept a new program download.
• Shut down communication functions (for nonpayment of monitoring fees in an owned system).
• Shut down all security system functions (for nonpayment for a leased system).
• Inhibit local keypad programming (prevents account takeover).
• Command the system to upload a copy of its resident program to the office.
• Set the time
• View/Modify
• Read: arming status, AC power status, lists of faulted zones, bypassed zones, zones currently in alarm,
zones currently in trouble, and RF sensors with low battery conditions; read control’s time.
Notes: (1)
(2)
After the control and the PC have established valid communication, “Service Update” will be displayed on the
LCD.
The detailed operation of the download functions is covered in the installation instructions for the Compass
Downloader for Windows.
- 46 -
LYNX Touch Installation and Setup Guide
Remote Programming/Control (Downloading)
Remote Programming Advisory Notes
• A copy of the program downloaded may be printed using the IBM PC-compatible computer’s internal
report generator, when an optional printer is connected (consult your PC manual for proper printer and
connections).
• The approximate time for program upload or download for a complete program is shown below:
Communication
Method
PSTN
GSM
IP
Approx.
Time
380 secs.
75 secs.
30 secs.
- 47 -
LYNX Touch Installation and Setup Guide
System Operation
Key/Touchscreen Operation
The keys and touchscreen allows the user to arm and disarm the system, and perform other system
functions, such as bypassing zones. Zone and system conditions (ALARM, trouble, bypass) are displayed on
the display. When an alarm occurs, console sounding and external sounding will occur, and the zone(s) in
alarm will be displayed on the display. Pressing any key will silence the keypad sounder for 10 seconds (only
once). Disarming the system will silence both console and external sounders. When the system is disarmed,
any zones that were in an alarm condition during the armed period will be displayed (memory of alarm). To
clear this display, simply repeat the disarm sequence by pressing the OFF key and entering the Security
Code. The console also features chime annunciation, and three panic key icons for silent, audible, fire or
personal emergency alarms. These keys can notify the central station of an alarm condition, if that service
is connected.
Panic Key/Icons
There are three panic key icons that, if programmed, are displayed on the virtual keypad when the “PANIC”
key is depressed for four seconds. The panic key screen will timeout if a selection is not made within ten
seconds. The keys can be used to manually initiate alarms and send a report to the central station. Each can
be individually programmed for 24-hour silent, audible, personal or fire emergency responses. The panic
function is activated when the respective keys is pressed. The panic functions are identified by the system as
follows:
Zone
95
96
99
Function
Fire Emergency
Medical Emergency
Police Emergency
Important: For the silent panic functions to be of practical value, the system must be connected to a central station.
Security Codes
Installer Code
The installer programs the 4-digit Installer Code initially as part of the programming procedure. The
factory default Installer Code is 4-1-1-2, but may be changed in the Installer Code programming
field. The Installer Code is the only code that allows entry into Installer Programming mode.
Master Code
In normal operation mode, the Master Code is used to enter the 4-digit User Security Codes.
Enter/change the Master code by installer.
The factory default Master Code for the LYNX Touch Control is set to 1-2-3-4. The Master Code is used to
enter the 4-digit User Security Codes.
SCREEN
ACTION
Ready To Arm
Users
Devices
Schedules
Test
Date Time
Events
Reminders
Slide Show
1.
After entering the User Tools/Programming Menu, select the “Users” icon
on the User Menu screen. The system displays the User Code
Programming screen
2.
Select “Master”, then select “Edit”.
3.
Enter a new four-digit Master Code on the displayed keypad The system
will display the new code on the left side of the screen.
Select “Done” when you are finished.
The system returns to the User Code Programming screen.
Back
5000-100-070-V0
Master ****
4.
5.
- 48 -
LYNX Touch Installation and Setup Guide
System Operation
Secondary User Codes
In normal operation mode, the Master Security Code can be used to assign up to 14 secondary 4-digit
security codes, including a Babysitter Code and a Duress Code. The Master Code can also be used to remove
secondary codes from the system (individually). Refer to the LYNX Touch User Manual for additional
information.
Security Code Notes
•
•
•
•
•
The Master and Secondary security codes permit access to the system for arming, disarming, etc.
The Installer Code can disarm the system only if it was used to arm it. In addition, the Installer Code cannot
disarm the system if it was armed by pressing and holding a Quick-Arm button.
The Babysitter Code can disarm the system only if it was used to arm it. In addition, the Babysitter Code cannot
disarm the system if it was armed by pressing and holding a Quick-Arm button.
Duress code sends a special code to the monitoring station when used to perform any system operation. Instruct
users to be careful not to use this code for normal usage.
Opening/closing reports are sent for the Installer Code, with the appropriate subscriber number. Master Code and
set of secondary user codes are sent as Nos. 02 and 03–14, respectively, in Contact ID® format (with the
appropriate user number).
- 49 -
LYNX Touch Installation and Setup Guide
System Operation
“Follow Me” System Announcement Feature
This feature allows the LYNX Touch to deliver a voice system message to the user phone numbers
programmed by the installer. The LYNX Touch will first transmit reports to the Central Station and after
receiving its kiss-off the system will dial the user phone numbers and begin transmitting the welcome
message “System Message, Press Star to Play”. The system will dial the user phone numbers a maximum of eight
times.
The “Follow Me” System announcements feature is only supported if PSTN line is available. The
announcements are individually sent to the User 1 and/or User 2 phone numbers which are programmed as
Phone 1 and Phone 2 respectively in the Reporter Programming section. System Follow Me announcements
are triggered by a system event that belongs to one of the Event Groups enabled by Installer individually for
User 1 and User 2. The groups are listed below.
• All Bypassing actions by a user
• Any Open/Close (arming/disarming status changes)
• Any Alarms
• Any Alarm Restores
• Alarm Cancel by the user
• Any System Troubles
• Any Test
• Non-security Events
If User 1 does not press a “*” key, LYNX Touch will hang up and will redial the User 1 number in 20
seconds. The control will make eight attempts before unsuccessfully ending the System “Follow Me” session
and erasing all the events in the User 1’s queue. The next call will be triggered by a new event from the
Event Group enabled for User 1.
If User 1 presses a “*” key, LYNX Touch will play back a sequence of System “Follow Me” announcements
from the User 1’s queue in chronological order starting with the oldest one. The announcements will
include “End of Message” at the end of the “Follow Me” announcements.
If a “*” key is pressed again during playback or within 15 seconds following the end of the playback, the
control will repeat the sequence. Otherwise the system will hang up, successfully ending the System “Follow
Me” session. Because the “*” key was pressed LYNX Touch will not redial the User 1 again. The next call
will be triggered by a new event from the Event Group enabled for User 1.
Note: The follow me system announcement will be terminated if any other event requires the system to send a report to the
Central Station. Once the PSTN line is available the session will be resumed and the control will again make up to 8
delivery attempts.
Follow Me Event Triggers
AC Loss
Audible Panic
Automatic Disarmed
Battery Failed Under Load
Burglary Zone Bypass
Carbon Monoxide Detected
Disarmed From AWAY or STAY
Emergency Alarm
Entry/Exit Alarm
Exit Error Alarm (zone)
Expansion Module Tamper
Expansion Module Failure
Expansion Module Tamper Alarm
Expansion Module Tamper Trouble
Fire Alarm
Fire Trouble
Interior Alarm
Follow Me
Announcement
AC Loss
Panic Alarm
Disarmed
System Low Battery
Zone ** Bypassed
Carbon Monoxide Alarm
Disarmed
Emergency Alarm
Perimeter Alarm
Perimeter Alarm
Tamper Alarm
System Trouble
Tamper Alarm
Tamper Alarm
Fire Alarm
System Trouble
Interior Alarm
Follow Me Event Triggers
Keypad Panic
Manual Test
Medical Alarm
Opening Keyswitch
Perimeter Alarm
Remote Disarm
RF Sensor Lost
Sensor Low Battery or Tamper
Silent Burglary
Siren Tamper
System Inactivity
System Low Battery
Water Leakage Alarm
Zone Bypass
Zone Tamper (Alarm)
Zone Trouble
** = Zone Number
- 50 -
Follow Me
Announcement
Panic Alarm
System Test
Emergency Alarm
Disarmed
Perimeter Alarm
Disarmed
System Trouble
Sensor Trouble
Silent Burglary
Tamper Alarm
No Check In
System Low Battery
Auxiliary Alarm
Zone ** Bypassed
Tamper Alarm
System Trouble
LYNX Touch Installation and Setup Guide
System Operation
“Follow Me” Reminder Feature
This feature allows the user to schedule a time driven message. When activated, the system will dial the
User 1 and/or User 2 phone numbers, which are programmed as Phone 1 and Phone 2 respectively by the
installer (in the Reporter Programming section), and deliver a recorded message. The LYNX Touch will
immediately begin transmitting the voice message and will repeat the message for 45 seconds. If the
message has timed out, the system will redial the programmed number a maximum of seven additional
times or until it is acknowledged. Pressing any key on the LYNX Touch keypad will terminate (acknowledge)
both the “Follow Me” reminder and the local reminder announcements.
Notes: (1) This feature is only supported if it has been programmed.
(2) The follow me reminder will be terminated if any other event requires the system to dial out, however, delivery of
the local schedule reminder message will continue.
(3) If a Central Station report must be sent, the “Follow Me” Reminder message will be suspended. Once the PSTN
line is available the session will be resumed and the control will again make up to 8 delivery attempts.
Remote Phone Control Feature
The remote phone control feature, which must be enabled, allows the user to access the security system from
any off-site touch-tone telephone. The control will pick up the incoming call, based on the specified ring
count, and will announce “SYSTEM ENTER CODE” every three seconds for the next nine seconds. During
this period the panel will wait for a valid User Code to be entered. If a valid User Code is not entered or the
nine second period expires a modem tone will be generated for remote programming (Compass
Downloading). If a valid User Code has been entered, the control will announce the current system status
and/or beeping sounds. Refer to the User Guide for additional information regarding this feature.
- 51 -
LYNX Touch Installation and Setup Guide
System Operation
System Displays
The following icons will be displayed on the Home screen along with specific zone status information
(if applicable) to indicate system status.
DISPLAY
DEFINITION
DISPLAY
DEFINITION
AC Loss
Door Open
Alarm
(intrusion)
Window Open
Armed Away
Exit Active
Armed Stay
Fire
Battery Low
Flood
Check Zones
Glass Break
CO Alarm
Medical Alarm
Disarmed Not
Ready to Arm
Motion
Disarmed
Ready to Arm
Temperature
90 RF Jam
Cover
Tamper
94 Phone
Line Cut
Reporter
Failure
103 Comm.
Trouble
Zone Status Displays
The following icons will be displayed on the Zone Status screen along with specific zone status information
when a zone has been Faulted, Bypassed or in Alarm.
DISPLAY
DEFINITION
Alarm
Fault (Yellow)
DISPLAY
DEFINITION
Ready
Trouble (red)
- 52 -
DISPLAY
DEFINITION
Bypass
LYNX Touch Installation and Setup Guide
System Operation
UL
Audio alarm verification has not been evaluated by UL.
Audio Alarm Verification (Two-Way Voice Feature)
This feature allows the central station operator to listen, talk to or conduct a two-way conversation with an
individual(s) at the premises. It also assists the operator in gathering information about the nature and
location of the alarm that may be helpful in responding to police and fire departments. All LYNX Touch
control panels are capable of supporting the Two-Way Voice feature. The LYNX Touch does not make system
announcements when the Two-Way voice feature is active.
Activation
Fire and CO alarms will prevent the LYNX Touch from starting an AAV session. A new Fire or CO alarm will
end an AAV session that is in progress.
The LYNX Touch sends the “alarm message” followed by a “Listen-in-to-Follow message” (Contact ID® code
606) to the Central Station. The Listen-in-to-Follow message causes the Central Station’s digital receiver to
temporarily hold the phone line for approximately 1-minute. When the LYNX Touch receives the “kissoff”
from the central station, indicating that the alarm message has been received, the Two-Way Voice (AAV)
feature is activated in the (default) “Listen Mode” and sirens and keypad sounds are discontinued. The
LYNX Touch transmits a beep acknowledgment to the Central Station, once per second. The beep alternates
between two tones and indicates that the LYNX Touch is waiting for a session command from the Central
Station operator. Once a command is issued the beep acknowledgement is discontinued, however, if a
command is not issued within two minutes the system will “time out” and the call will be terminated.
Operator Commands
The Central Station operator begins the session, which last 5 minutes, by entering one of the valid AAV
commands shown in the table below. The session may be extended 5 minutes, without changing the
operating mode, by pressing the [7] key on the touch-tone phone. Selecting another operating mode also
resets the session an additional 5 minutes. During the last minute of the 5 minute, session, the LYNX
Touch generates two beeps every 30 seconds to alert the Central Station operator that the session is about to
time out. The Central Station operator may then extend the session by pressing the [7] key on the touch-tone
phone. If the session is not extended the phone line is disconnected, and the session is ended. Sessions may
be ended at any time by pressing the [9] key on the touch-tone phone. The AAV modes are described as
follows:
Note: When entering AAV commands make sure the Central Station receiver has been disconnected from the phone
line, otherwise AAV commands may not go through.
Key
Function
Talk Mode: Pressing the [1] key on the touch tone phone, enables one-way voice communication from the
central station to the violated premises, and allows the operator to talk communicate through the LYNX
Touch speaker. In this mode the ARMED (red) and READY (green) LEDs blink alternately.
VOX (Voice) Mode: Pressing the [2] key on the touch-tone phone, enables two-way voice communications
between the central station and the violated premises. In this mode the ARMED (red) and READY (green)
LEDs blink alternately.
Listen Mode: Pressing the [3] key on the touch-tone phone, enables one-way audio from the violated premises
to the central station. The Listen Mode is the start up default mode of the voice feature and allows the
operator to listen through the LYNX Touch microphone. This mode does not affect the existing LED pattern.
Extends the session 5 minutes without changing its operating mode.
Ends the session and disconnects the phone line.
- 53 -
LYNX Touch Installation and Setup Guide
System Operation
Event Log
The LYNX Touch Series event log is capable of recording and displaying up to 128 system events. The type
of events that can be recorded is selectable and is programmed in the System Type programming field. The
event log can be reviewed by entering the Installer Programming or Master User Programming mode. Refer
to the LYNX Touch Series User Manual for additional information.
Note: In the unlikely condition that the backup battery becomes fully discharged when AC power is lost, any system activity
performed after the low battery notification will not be saved in the event log. Additionally, the panel will revert to the
status condition as before the low battery notification.
Contact ID® & SIA Event Log Codes
CID
SIA
Definition
Definition
Code
Code
110
Alarm, Fire
AT/AR
AC Trouble/AC Restoral
121
Alarm, Duress
BA/BR
Burglary Alarm/Burglary Restoral
122
Alarm, Silent
BB/BU
Burglary Bypass/Burglary Unbypass
123
Alarm, Audible
CA/CD
Automatic Closing/Closing Delinquent
131
Alarm, Perimeter
CI
Fail to Close
132
Alarm, Interior
CL
Closing Report
134
Alarm, Entry/Exit
CQ
Remote Closing
135
Alarm, Day/Night
CR
Recent Closing
137
Alarm, Tamper
CS
Closing Keyswitch
145
Expansion Module Tamper
DF/DR
Door Forced/Door Restoral
146
Silent Burglary
EA
Exit Alarm
150
24-Hour Non-Burglary
EM/EN
Expansion Device Missing/Expansion Missing Restore
162
Carbon Monoxide Detected
ES/EJ
Expansion Device Tamper/Expansion Tamper Restore
301
Trouble, AC Loss
ET
Expansion Trouble
302
Trouble, Low System Battery
FA
Fire Alarm
305
Trouble, System Reset
FT/FJ
Fire Trouble/Fire Trouble Restore
341
Trouble, Case Tamper
FT/FJ
Fire Trouble/Fire Trouble Restore
344
Trouble, RF Receiver Jam Detect
HA/HR
Holdup Alarm/Holup Restoral
351
Trouble, Telco 1 Fault
JL
Log Threshold
353
Trouble, Long Range Radio Transmitter Fault
LB/LX
Local Progr./Local Progr. End (Logged in Event Log )
354
Trouble, Failure to Communicate Event
LT/LR
Phone Line Trouble/Phone Line Restoral
373
Trouble, Fire Trouble
MA/MR Medical Alarm/ Medical Restoral
374
Trouble, Exit Error Alarm
OA
Automatic Opening
380
Trouble, Sensor
OC
Cancel Report
381
Trouble, Loss of Supervision RF
OP
Opening Report
383
Trouble, Sensor Tamper
OQ
Remote Opening
384
RF Low Battery
OS
Opening Keyswitch
401
Open/Close by User
PA
Panic Alarm
403
Open/Close Automatic
RP
Automatic Test
406
Cancel
RS
Remote Program Success
407
Remote Arm/Disarm
RX
Manual Test
408
Quick Arm
TA/TH
Tamper Alarm/Tamper Alarm Restore
409
Open/Close Keyswitch
TJ
Tamper Trouble Restore
412
Successful Download
TS/TE
Test Start/Test End
441
Armed Stay
TT
Tamper Trouble
442
Keyswitch Armed STAY
UA
Untyped Zone Alarm
455
Auto-Arm Failed
UB/UU
Untyped Zone Bypass/Untyped Zone Unbypass
459
Recent Close
WA/WR Water Alarm/Water Restoral
570
Zone/Sensor Bypass
XQ/XH
RF Interference/RF Interference Restore
601
Manual Trigger Test Report
XT/XR
Transmitter Battery Trouble/Transmitter Battery Restoral
602
Periodic Test Report
YC/YK
Communications Fail/Communications Restoral
606
Listen-in to follow
YM
System Battery Missing
607
Walk Test
YT/YR
System Battery Trouble/System Battery Restoral
623
Event Log 80% Full
627
Program Mode Entry (Logged in Event Log Only)
628
Program Mode Exit (Logged in Event Log Only)
654
System Inactivity
759
Resident Monitor Zone Response
760
Resident Response Zone Response
761
General Monitor Zone Response
762
General Response Zone Response
Note: LRR/IP Communications Module Low Battery and Low Battery restore reports are sent real time. LRR/IP Communications Module
trouble restore report is sent after two OFF Sequences (only if physically restored).
- 54 -
LYNX Touch Installation and Setup Guide
Testing the System
Test Mode
After installation is completed, the security system should be carefully tested, as follows.
1. With the system in the disarmed state, check that all zones are intact. If the READY LED is not lit,
select the Zones icon to display the faulted zone(s). If necessary, restore faulted zone(s) so that the
READY LED lights. Fault and restore every sensor individually to assure that it is being monitored by
the system.
Armed System Test
Alarm messages will be sent to the central station during the following tests 1 and 2. Notify the
Central Station in advance that tests will be in progress.
1. Arm the system and fault one or more zones. After 15 seconds (if optional dialer delay is selected),
silence alarm sounder(s) by pressing OFF and entering the security code. Check entry/exit delay zones.
2. Check the keypad-initiated alarms that are in the system by selecting the Panic key. If the system has
been programmed for audible emergency, the keypad will emit a steady alarm sound, and “ALARM”
and zone number will be displayed. For LYNX Touch, silence the alarm pressing OFF and entering the
security code. For LYNX Touch SIA configuration, silence the alarm by entering the security code.
If the system has been programmed for silent emergency, there will be no audible alarms or displays,
but a report will be sent to the central station.
3. Notify the central station when all tests are finished, and verify results with them.
4. To test the wireless part of the system and the RF receiver, perform the two additional tests described
in the Installing Wireless Zones section: Sniffer mode and Go/No Go Test.
Note:
System Test mode and Go/No Go Test will be automatically terminated after 3-1/2 to 4 hours if the installer or user
does not manually terminate it. This ensures that fire and panic zones will not remain disabled. However, Sniffer
mode does not automatically expire. You must manually exit (by entering an OFF Sequence) Sniffer mode to return
to normal operation. During the final 5 minutes the system will emit double beeps indicating that the end of Test
mode is nearing.
Dialer Test
The Dialer Test checks that the phone connection to the central station is working properly. Notify the
Central Station in advance that tests will be in progress.
1. With the System in the Installer Programming mode, select the “Test” button and then select the
“Dialer Test” button.
2. If the test is successful the system will send the Manual Trigger Test Report (E601) to the Central
Station. The test will not be recorded in the Event Log.
3. The system will make 8 attempts to test the dialer for both the Primary and Secondary Central Station,
as applicable. If the test is unsuccessful the system will display a “Reporter Failure” trouble message
after 1-17 minutes.
TO THE INSTALLER
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory
operation of any alarm system.
The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting
the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a
specific program of frequent testing (at least weekly) to ensure the system’s proper operation at all times.
- 55 -
LYNX Touch Installation and Setup Guide
LYNX Touch Programming Default Tables
Program Function
Installer Code
System Type
RF Jam
Speaker Phone
Two Way Voice
RF House Code
Phone Notification
Remote Phone
Phone Detect Time
Events - Log All
Events - Log Alarm
Events - Log Bypass
Events - Log Open/Close
Events - Log Trouble
Non Security
Remote Access Serial
Multi Mode Serial
Date Time
Calendar
Enter Time
Time Zone
Day Light Savings time
Start Month
Start Week
End Month
End Week
Communicator
Communications Path
Primary City Id
Pri Central Station Id
Primary Subscriber Id
Supervision
Old Alarm Time
Remote Acc. IP or GSM
Multi Mode IP or GSM
GSM Fault Time
IP Fault Time
Use DHCP
NI IP Address
Subnet Mask
Gateway IP Address
DNS Server IP Address
Zones
Reporter
Primary Central Station
Phone Type
Communicator Type
Phone Number
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Table 1
Table 2
Table 3
Table 4
4112
4112
4112
4112
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Press To Log All
Enabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Log All Set
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Log All Set
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Log All Set
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
None
None
None
None
24 Hours
10 Minutes
Disabled
Disabled
00
00
Yes
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
None
None
None
None
None
None
None
None
24 Hours
24 Hours
10 Minutes
10 Minutes
Disabled
Disabled
Disabled
Disabled
00
00
00
00
Yes
Yes
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
See Zone Programming Default Tables
None
None
None
None
24 Hours
10 Minutes
Disabled
Disabled
00
00
Yes
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
- 56 -
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
LYNX Touch Installation and Setup Guide
LYNX Touch Programming Default Tables
Program Function
Secondary Central Station
Phone Type
Communicator Type
Phone Number
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Phone 1
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Phone 2
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Report Selection
Arm Away
Arm Stay
Disarm
Exit Error
Recent Closing
Event Log Full
Trouble
Trouble Restore
Alarm Restore
Alarm Cancel
Test
Test Restore
Bypass
Bypass Restore
AC Loss
AC Loss Restore
Low Battery
Low Battery Restore
RF Low Battery
RF Low Battery Restore
Options
PBX
Call Wait Cancel
Number of Reports
Alarm Report Delay
First Report Offset
Report Frequency
Table 1
Table 2
Table 3
Table 4
Contact Id: 4 Digit
None
None
FFFF
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Blank
Blank
Unlimited
No Delay
6 Hrs
Never
Blank
Blank
Unlimited
15 Seconds
12 Hrs
30 Days
Blank
Blank
Unlimited
No Delay
12 Hrs
Never
Blank
Blank
Unlimited
No Delay
12 Hrs
Never
- 57 -
LYNX Touch Installation and Setup Guide
LYNX Touch Programming Default Tables
Program Function
Downloader
Phone Answer
Ans. Machine Defeat
Modem Speed (Future Use)
Ring Counter
Callback Number
Flexible Callback
Number
Sounder
Burglary Alarm Sound
Burglary Bell Timeout
Fire Bell Timeout
Arm Confirm
Alarm Options
System Settings
Entry Delay 1
Entry Delay 2
Exit Delay
Backlight Timeout
Quick Arm
Quick Exit
Restart Exit Time
Force Bypass
Exit Warning
Auto Stay Arming
Lack Of Usage Notify
Power-Up In Pervious
Display Alarm Cancel
Display Exit Time
Cross Zone Delay
Cross Zone 1
Cross Zone 2
Table 1
Table 2
Table 3
Table 4
Yes
Yes
Slow
Blank
No
Yes
Yes
Slow
Blank
No
Yes
Yes
Slow
Blank
No
Yes
Yes
Slow
Blank
No
Yes
4 Minutes
4 Minutes
None
Unlimited
Yes
4 Minutes
4 Minutes
None
Yes
4 Minutes
4 Minutes
None
Yes
4 Minutes
4 Minutes
None
30 Seconds
60 Seconds
60 Seconds
No
Yes
Yes
No
No
No
No
Disabled
Yes
No
Yes
3 Minutes
Disabled
Disabled
45 Seconds
60 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
Yes
Yes
None
Disabled
Disabled
30 Seconds
60 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
Yes
Yes
None
Disabled
Disabled
30 Seconds
60 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
Yes
Yes
None
Disabled
Disabled
- 58 -
LYNX Touch Installation and Setup Guide
LYNX Touch SIA Programming Default Tables
Program Function
Installer Code
System Type
RF Jam
Speaker Phone
Two Way Voice
RF House Code
Phone Notification
Remote Phone
Phone Detect Time
Events - Log All
Events - Log Alarm
Events - Log Bypass
Events - Log Open/Close
Events - Log Trouble
Non Security
Remote Access Serial
Multi Mode Serial
Date Time
Calendar
Enter Time
Time Zone
Day Light Savings time
Start Month
Start Week
End Month
End Week
Communicator
Communications Path
Primary City Id
Pri Central Station Id
Primary Subscriber Id
Supervision
Old Alarm Time
Remote Acc. IP or GSM
Multi Mode IP or GSM
GSM Fault Time
IP Fault Time
Use DHCP
NI IP Address
Subnet Mask
Gateway IP Address
DNS Server IP Address
Zones
Reporter
Primary Central Station
Phone Type
Communicator Type
Phone Number
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Table 1
Table 2
Table 3
Table 4
4112
4112
4112
4112
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Press To Log All
Enabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Log All Set
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Log All Set
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Enabled
2 Minutes
Log All Set
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
January 1, 2011
10:00AM
Eastern (EST)
Yes
March
Second
November
First
None
None
None
None
24 Hours
10 Minutes
Disabled
Disabled
00
00
Yes
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
None
None
None
None
None
None
None
None
24 Hours
24 Hours
10 Minutes
10 Minutes
Disabled
Disabled
Disabled
Disabled
00
00
00
00
Yes
Yes
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
See Zone Programming Default Tables
None
None
None
None
24 Hours
10 Minutes
Disabled
Disabled
00
00
Yes
255.255.255.255
255.255.255.255
255.255.255.255
255.255.255.255
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
- 59 -
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
LYNX Touch Installation and Setup Guide
LYNX Touch SIA Programming Default Tables
Program Function
Secondary Central Station
Phone Type
Communicator Type
Phone Number
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Phone 1
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Phone 2
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Report Selection
Arm Away
Arm Stay
Disarm
Exit Error
Recent Closing
Event Log Full
Trouble
Trouble Restore
Alarm Restore
Alarm Cancel
Test
Test Restore
Bypass
Bypass Restore
AC Loss
AC Loss Restore
Low Battery
Low Battery Restore
RF Low Battery
RF Low Battery Restore
Options
PBX
Call Wait Cancel
Swinger Shutdown
Abort Window
First Report Offset
Report Frequency
Table 1
Table 2
Table 3
Table 4
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
Contact Id: 4 Digit
None
None
FFFF
None
None
Report All Set
Enabled
Enabled
Enabled
Enabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
None
None
Press To Report All
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Blank
Blank
30 Seconds
6 Hrs
Never
Blank
Blank
30 Seconds
12 Hrs
30 Days
Blank
Blank
30 Seconds
12 Hrs
Never
Blank
Blank
30 Seconds
12 Hrs
Never
- 60 -
LYNX Touch Installation and Setup Guide
LYNX Touch SIA Programming Default Tables
Program Function
Downloader
Phone Answer
Ans. Machine Defeat
Modem Speed (Future Use)
Ring Counter
Callback Number
Flexible Callback
Number
Sounder
Burglary Alarm Sound
Burglary Bell Timeout
Fire Bell Timeout
Arm Confirm
System Settings
Entry Delay 1
Entry Delay 2
Exit Delay
Backlight Timeout
Quick Arm
Quick Exit
Restart Exit Time
Force Bypass
Exit Warning
Auto Stay Arming
Lack Of Usage Notify
Power-Up In Pervious
Display Alarm Cancel
Display Exit Time
Cross Zone Delay
Cross Zone 1
Cross Zone 2
Table 1
Table 2
Table 3
Table 4
Yes
Yes
Slow
Blank
No
Yes
Yes
Slow
Blank
No
Yes
Yes
Slow
Blank
No
Yes
Yes
Slow
Blank
No
Yes
4 Minutes
4 Minutes
None
Yes
4 Minutes
4 Minutes
None
Yes
4 Minutes
4 Minutes
None
Yes
4 Minutes
4 Minutes
None
30 Seconds
30 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
No
Yes
3 Minutes
Disabled
Disabled
30 Seconds
30 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
Yes
Yes
None
Disabled
Disabled
30 Seconds
30 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
Yes
Yes
None
Disabled
Disabled
30 Seconds
30 Seconds
60 Seconds
No
Yes
Yes
Yes
No
Yes
Yes
Disabled
Yes
Yes
Yes
None
Disabled
Disabled
Zone Programming Default Tables
Zone Assignment/Alarm Report Codes for Table 1
Zone
Loop
Supervision/
Device Type
Response Type
Report
Chime
Zone Descriptor
Number Number
Input Type
--New
n/a
yes
no
EOLR
n/a
Door
Entry Exit 1
yes
yes
RF Supervised
Front Door
Door
Entry Exit 1
yes
yes
RF Supervised
Back Door
Window
Perimeter
yes
yes
RF Supervised
n/a
Motion Sensor
Interior w/Delay
yes
no
RF Supervised
n/a
49
4 Button Key
Arm Away
yes
no
Button
n/a
50
4 Button Key
Disarm
yes
no
Button
n/a
51
4 Button Key
Arm Stay
yes
no
Button
n/a
52
4 Button Key
No Response
no
no
Button
n/a
53
4 Button Key
Arm Away
yes
no
Button
n/a
54
4 Button Key
Disarm
yes
no
Button
n/a
55
4 Button Key
Arm Stay
yes
no
Button
n/a
56
4 Button Key
No Response
no
no
Button
n/a
92
------yes
no
Duress Trigger
n/a
95
--Fire
Fire No Verification
yes
no
Panic Trigger
n/a
96
--Medical
n/a
yes
no
Panic Trigger
n/a
97
------yes
no
Cover Tamper
n/a
99
--Police
24-Hour Silent
yes
no
Panic Trigger
n/a
NOTE: Zone 1 is a hardwire zone; Zone 2 to 48 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic
- 61 -
LYNX Touch Installation and Setup Guide
Zone Programming Default Tables
Zone Assignment/Alarm Report Codes for Table 2
Zone
Loop
Supervision/
Device Type
Response Type
Report
Chime
Zone Descriptor
Number Number
Input Type
--New
n/a
yes
no
EOLR
n/a
Door
Entry Exit 1
yes
yes
RF Supervised
Front Door
Door
Entry Exit 1
yes
yes
RF Supervised
Back Door
Door
Entry Exit 1
yes
yes
RF Supervised
Garage Door
Motion Sensor
Interior w/Delay
yes
no
RF Supervised
n/a
Smoke Detector
Fire No verification
yes
no
RF Supervised
n/a
49
4 Button Key
Arm Away
yes
no
Button
n/a
50
4 Button Key
Disarm
yes
no
Button
n/a
51
4 Button Key
Arm Stay
yes
no
Button
n/a
52
4 Button Key
No Response
no
no
Button
n/a
53
4 Button Key
Arm Away
yes
no
Button
n/a
54
4 Button Key
Disarm
yes
no
Button
n/a
55
4 Button Key
Arm Stay
yes
no
Button
n/a
56
4 Button Key
No Response
no
no
Button
n/a
92
------yes
no
Duress Trigger
n/a
95
--Fire
Fire No Verification
yes
no
Panic Trigger
n/a
96
--Medical
24-Hour Auxiliary
yes
no
Panic Trigger
n/a
97
------yes
no
Cover Tamper
n/a
99
--Police
24-Hour Audible
yes
no
Panic Trigger
n/a
NOTE: Zone 1 is a hardwire zone; Zone 2 to 48 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic
Zone Assignment/Alarm Report Codes for Tables 3 and 4
Zone
Loop
Supervision/
Device Type
Response Type
Report
Chime
Zone Descriptor
Number Number
Input Type
--New
n/a
yes
no
EOLR
n/a
Door
Entry Exit 1
yes
yes
RF Supervised
Front Door
Door
Entry Exit 1
yes
yes
RF Supervised
Back Door
Window
Perimeter
yes
no
RF Supervised
n/a
Window
Perimeter
yes
no
RF Supervised
n/a
Window
Perimeter
yes
no
RF Supervised
n/a
Window
Perimeter
yes
no
RF Supervised
n/a
Motion Sensor
Interior w/Delay
yes
no
RF Supervised
n/a
Smoke Detector
Fire No Verification
yes
no
RF Supervised
n/a
49
4 Button Key
Arm Away
yes
no
Button
n/a
50
4 Button Key
Disarm
yes
no
Button
n/a
51
4 Button Key
No Response
yes
no
Button
n/a
52
4 Button Key
No Response
no
no
Button
n/a
53
4 Button Key
Arm Away
yes
no
Button
n/a
54
4 Button Key
Disarm
yes
no
Button
n/a
55
4 Button Key
No Response
yes
no
Button
n/a
56
4 Button Key
No Response
no
no
Button
n/a
92
------yes
no
Duress Trigger
n/a
95
--Fire
Fire No Verification
yes
no
Panic Trigger
n/a
96
--Medical
n/a
yes
no
Panic Trigger
n/a
--yes
no
97
--Cover Tamper
n/a
99
--Police
24-Hour Silent
yes
no
Panic Trigger
n/a
NOTE: Zone 1 is a hardwire zone; Zone 2 to 48 are RF zones; Zone 92 is Duress; Zones 95, 96 and 99 are keypad panics
- 62 -
LYNX Touch Installation and Setup Guide
Regulatory Agency Statements
Federal Communications Commission (FCC) Part 15
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
•
•
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC IC Statement
This device complies with Part 15 of FCC Rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les
interferences causant une reception indésirable.
TELEPHONE/MODEM INTERFACE
Federal Communications Commission (FCC) Part 68
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and
Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested.
This equipment uses the following USOC jack: RJ31X
This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This equipment is
hearing-aid compatible.
Industry Canada
NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network
protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The
Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe
system, if present, are connected together, This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as
appropriate.
AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection,
d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives
au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Le
matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la
conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.
Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications
peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais
fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques et des
canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.
Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des installations
électriques, ou à un électricien, selon le cas.
Ringer Equivalence Number Notice:
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être
raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition
que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
RF Exposure
WARNING: The LYNX Touch must be installed to provide a separation distance of at least 7.8 in (20 cm) from all
persons and not co-located or operated in conjunction with any other transmitter.
- 63 -
LYNX Touch Installation and Setup Guide
WARNING
THE LIMITATIONS OF THIS ALARM SYSTEM
While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or
other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a
variety of reasons. For example:
•
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or
disconnect an alarm warning device.
•
Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work
without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put
in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.
•
Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the
signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.
•
A user may not be able to reach a panic or emergency button quickly enough.
•
While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not
activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the
Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may
not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not
sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of
closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector,
for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke
detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by
carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable
materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire
and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to
allow all occupants to escape in time to prevent injury or death.
•
Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their
installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams
of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion
or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.
Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical
system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the
ambient temperature of the protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection
performance can decrease.
•
Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the
other side of closed or partly open doors. If warning devices are located on a different level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not
hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing
traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people.
•
Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or
temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.
•
Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond
appropriately.
•
This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to
last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This
alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad
(and remote keypad) should be tested as well.
Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions.
Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device
being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce
the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus
allowing time to arrange a change of battery to maintain protection for that given point within the system.
Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for
insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to
insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones
to learn about these developments.
- 64 -
LYNX Touch Installation and Setup Guide
UL NOTICES
1. For UL Residential Burglar Alarm installations with line security, total exit delay time must not
exceed 60 seconds. For UL Burglar Alarm installations without line security, total exit delay time
must not exceed 120 seconds.
2. Periodic testing (see scheduling mode) must be at least every 24 hours.
3. Remote downloading without an alarm company technician on-site (unattended downloading) is not
permissible for UL installations.
4. Auto-disarming is not a UL Listed feature.
5. As SIA limits for delay of alarm reporting and sounding can exceed UL limits for commercial and
residential applications, the following UL requirements per UL681 are provided:
The maximum time that a control unit shall be programmed to delay the transmission of a signal to a
remote monitoring location, or to delay the energizing of a local alarm sounding device to permit the
alarm system user to enter and disarm the system, or to arm the system and exit shall not exceed:
a) 60 seconds for a system with standard line security or encrypted line security,
b) 120 seconds for a system without standard line security or encrypted line security, or
c) 120 seconds for a system that does not transmit an alarm signal to a remote monitoring location.
SIA Quick Reference Guide
1.
2.
3.
4.
7.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Report Alarms: Default is “Enabled”
Report Troubles: Default is “Enabled”
Exit Error: Default is “Enabled”.
Recent Closing: Default is “Enabled”.
Alarm Cancel: Default is “Enabled”.
Call Wait Cancel: If call waiting is used, a call waiting cancel prefix must be entered.
Swinger Shutdown: Options for “alarm sounding per zone” include 1 report or 2 reports. Default is “2
Reports”.
Abort Window: Options include 15, 30 and 45 seconds. Default is 30 seconds.
Entry Delay 1 and 2: Options include 30, 45, 60 and 90 seconds and 2, 3 or 4 minutes. Minimum entry
delay is 30 seconds. When added together the entry delay plus the dialer delay should not exceed 1
minute.
Exit Delay: Options include 45, 60, 90 seconds and 2 minutes. Minimum exit delay is 45 seconds.
Restart Exit Time: Default is “Yes”.
Exit Warning: Always enabled. This field is not programmable
Auto Stay Arming: Default is “Yes”.
Cross Zone Delay: Options include None or selections between 30 seconds and 2 minutes (in 30 second
increments), 3 minutes and 4 minutes. Default is 3 minutes.
- 65 -
LYNX Touch Installation and Setup Guide
Specifications
LYNX Touch Series Security Controls
Physical:
Dimensions:
8.5” W x 6” H x 1.875” D
Electrical:
Voltage Input:
9 Vdc from plug-in 2.7A power supply
Rechargeable Backup Battery: Nickel-metal hydride battery pack rated at 7.2 Vdc
Communication:
Formats Supported:
ADEMCO Contact ID® Reporting, 10 characters/sec., DTMF (TouchTone)
Data Tones, 1400/2300Hz Handshake, 1400Hz Kissoff.
Line Seize:
SIA/DCS Format, 2225Hz Handshake, Data Tones, 2025/2235Hz, baud
Double Pole
Ringer Equivalence:
0.5B
ACTA Registration No.:
US: AC3AL05BL5000
Hardwire Zone:
2K ohms, End of Line Resistor (EOLR), 200 ohms max wire resistance, dry
contacts only
Trigger Output:
1k ohms to ground when closed (output low) 3ma
- 66 -
LYNX Touch Installation and Setup Guide
Contacting Technical Support
PLEASE, before you call Technical Support, be sure you:
• READ THE INSTRUCTIONS!
•
Check all wiring connections.
•
Determine that the power supply and/or backup battery are supplying proper voltages.
•
Verify your programming information where applicable.
•
Note the proper model number of this product, and the version level (if known) along with any
documentation that came with the product.
•
Note your Honeywell customer number and/or company name.
Having this information handy will make it easier for us to serve you quickly and effectively.
Technical Support: ........................................................................................................ 1-800-645-7492 (8 a.m.-10 p.m. E.S.T.)
MyWebTech: ..............................................................................http:// www.honeywell.com/security/hsc/resources/MyWebTech
- 67 -
LYNX Touch Installation and Setup Guide
Glossary
AES – Advanced Encryption Standard
DHCP – Dynamic Host Configuration Protocol, which provides a mechanism for allocating IP addresses
dynamically so that addresses can be reused when hosts no longer need them.
DNS – Domain Name System, which is a distributed hierarchical naming system used to resolve domain
names (e.g., www.yahoo.com) into numerical IP addresses (e.g., 204.17.25.1).
Gateway IP Address – A gateway (sometimes called a router) is a computer and/or software used to connect
two or more networks (including incompatible networks) and translates information from one network to the
other. The Gateway IP address is the IP address for the gateway.
GPRS – (General Packet Radio Service)
GSM – Global System for Mobile communications, which is an international standard for digital mobile
phone systems used for cellular communication.
IMEI – International Mobile Equipment Identity number
IP – Internet Protocol
IP Address – A unique number consisting of four parts separated by periods, sometimes called a "dotted
quad.," for example: 204.17.29.11, assigned to every computer/workstation connected to the Internet. IP
numbers can be "static" (assigned and unchanging) or "dynamic," assigned via DHCP at each and every
startup.
ISP – Internet Service Provider
MAC ID – Media Access Code; located on the module label.
NIC – Network Interface Card.
RSSI – Received Signal Strength Indication.
SCID – SIM Card ID
Subnet Mask – A Subnet is a portion of a network that shares a network address with other portions of the
network, and is distinguished by a subnet number. The Subnet Mask is a 32-bit address mask used in IP to
indicate the bits of an IP address that are being used for the subnet address.
- 68 -
LYNX Touch Installation and Setup Guide
– Index –
Features .................................................................... 5
Flexible Callback .................................................... 46
Follow Me Reminder Feature ................................ 51
Follow Me System Announcement ........................ 50
Force Bypass........................................................... 37
General Programming Information....................... 16
Go/No Go Test......................................................... 13
GSM Information.................................................... 40
GSMVLP5 ......................................................... 10, 23
House Identification ............................................... 12
ILP5................................................................... 10, 11
Installer Code ......................................................... 48
Installer Menu ........................................................ 16
Installing Wireless Zones................................. 13, 14
Key/Touchscreen Operation ................................... 48
Keys......................................................................... 12
L5000DM .................................................................. 6
Lack of Usage Notify .............................................. 37
Liquid Crystal Display (LCD) Touch-Screen ........ 15
Loading Factory Defaults....................................... 17
LYNXRCHKIT-SC.................................................... 5
LYNXRCHKIT-SHA................................................. 5
Master Code............................................................ 48
Master Security Code ....................................... 20, 48
Memory of Alarm.................................................... 48
Menu Screens ......................................................... 15
Mounting Base.......................................................... 6
Navigating Menus .................................................. 15
Navigation Keys ..................................................... 15
Operator Commands .............................................. 53
Panic Key/Icons ...................................................... 48
Plug-in Power Supply............................................... 9
Power-Up in Previous............................................. 37
Program Date And Time ........................................ 23
Program Keys ......................................................... 28
Program the Communications Module.................. 24
Program Zones................................ 26, 28, 30, 36, 37
Programming Default Tables... 56, 57, 58, 59, 60, 61
Quick Arm............................................................... 37
Quick Exit ............................................................... 37
Range ...................................................................... 12
Register by Phone................................................... 42
Register Device with PIN....................................... 43
Register Through Alarmnet Direct Website ......... 42
Register Through LYNX Touch Diagnostics ......... 42
Registering The LYNX Touch ................................ 41
Regulatory Agency Statements.............................. 63
Remote Phone Control............................................ 51
Remote Programming ............................................ 46
Remote Programming/Control ............................... 46
Reporter ............................................................ 30, 31
Resident Monitor Zone Types .................................. 5
RF Sniffer Test Mode ............................................. 13
Secondary User Codes ............................................ 49
Security Code Handshake...................................... 46
Security Codes .................................................. 37, 48
Setup Communication............................................ 41
SIA (DC-03)............................................................... 5
SIA Event Code ...................................................... 54
24-Hour Silent Alarm .............................................48
300-03864-1...............................................................5
300-03866..................................................................5
300-04063..............................................................5, 9
300-04065..............................................................5, 9
300-04705..............................................................5, 9
5800 Series Transmitter Loop Numbers ...............14
5800 Series Transmitters ...................................5, 12
5802MN...................................................................12
5802MN2.................................................................12
5804 .........................................................................12
5804BD....................................................................12
5804BDV .................................................................12
5804E ......................................................................12
5805-6......................................................................12
5806 .........................................................................14
5816 .........................................................................12
5817 .........................................................................12
AC Power ..................................................................9
AC Power Loss ..........................................................9
ADEMCO Contact ID .........................................5, 66
Armed System Test ................................................55
Audio Alarm Verification
(Two-Way Voice Feature) .......................................53
Auto Stay Arming ...................................................37
Babysitter Code ......................................................49
Backup Battery............................................... 3, 9, 66
Button Transmitters...............................................12
Case Tamper .............................................................5
Change Installer Code............................................20
Communication Modules........................................10
Communications ID Numbers ...............................41
Communications Status .........................................40
Installing/Configuring Communication Modules..10
Contact ID® Codes .................................................54
Contact ID Event Codes .........................................54
Contact ID Reporting .............................................66
Contacting Technical Support................................67
Cross Zone 1/Cross Zone 2......................................37
Cross Zone Delay ...................... 37, 38, 39, 58, 61, 65
Data Encryption .....................................................46
Desktop Mounting ....................................................6
Diagnostics........................................................40, 41
Dialer Delay ......................................................55, 65
DIP Switches...........................................................12
Display Alarm Cancel.............................................37
Display Exit Time...................................................37
Duress Code ............................................................49
Enter Installer Programming Mode ......................17
Enter/Change the Master Code .............................48
Entry Delay1/Entry Delay 2 ..................................37
Entry/Exit Burglary ...............................................18
Ethernet Information .............................................40
Event Log Codes .....................................................54
Exit Delay ............................. 5, 15, 16, 18, 37, 55, 65
Exit Door .................................................................37
Exit Warning ..........................................................37
Exiting Program Mode ...........................................17
Factory Defaults .....................................................45
FCC Statement .......................................................63
- 69 -
LYNX Touch Installation and Setup Guide
Touch-Screen Display .............................................15
Transmitter Battery Life........................................12
Transmitter Input Type .........................................12
Transmitter Loop Numbers....................................14
Transmitter Supervision ........................................12
Unsupervised Button..............................................12
Unsupervised RF ....................................................12
Update Server .........................................................44
User Menu...............................................................16
Wall Mounting ..........................................................6
Wireless Buttons.....................................................12
Wireless Keypads..........................................5, 12, 13
Wireless Zones ........................................................12
Wiring Connections ..................................................6
World Wide Web Address .......................................67
Zone Programming Default Tables ..................61, 62
Zone Response Type Definitions ............................18
Silent Burglary .......................................................19
Site-Initiated Remote Programming......................46
Sniffer Mode ............................................................55
Sounder ...................................................................36
Specifications ..........................................................66
Station-Initiated Remote Programming ................46
Super High Capacity Battery .................................10
Supervised RF .........................................................12
System Displays......................................................52
System Features .......................................................5
System Operation .............................................48, 49
System Settings ......................................................37
Technical Support ...................................................67
Test Communications .............................................41
Test Ethernet ..........................................................41
Test Mode ................................................................55
Testing the System .................................................55
- 70 -
- 71 -
EDGE
CONNECT
(FUTURE
USE)
REPLACE EVERY FOUR YEARS
P/N 300-03864-1/LYNXRCHKIT-SC
P/N 300-03866/LYNXRCHKIT-SHA
THE LYNX TOUCH CONTROLS ARE COMPATIBLE WITH THE
FOLLOWING INTEGRAL RECHARGEABLE BATTERY PACKS:
EGND
EARTH GROUND
STANDARD CAPACITY
BATTERY CONNECTOR
SUPER HIGH CAPACITY
BATTERY CONNECTOR
ZONES
2K
OHM
EOLR
HARD
WIRED
ZONE
WEEKLY TESTING IS REQUIRED TO ENSURE
PROPER OPERATION OF THIS SYSTEM
TAMPER
SWITCH
GSMVLP5/ILP5
RECEPTACLE
TELCO
JACK
INCOMING
PHONE LINE
WARNING
CONTROL UNIT
DELAY-SEC
30 seconds
CIRCUIT
(ZONE)
02 - 48
ZT16
5806W3
5000-100-SOC-V0
10 seconds
SMOKE DETECTOR
MODEL
DELAY-SEC
THIS UNIT MAY BE PROGRAMMED TO INCLUDE AN ALARM
VERIFICATION FEATURE THAT WILL RESULT IN A DELAY OF THE
SYSTEM ALARM SIGNAL FROM THE INDICATED FIRE CIRCUITS.
THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS)
SHALL NOT EXCEED 60 SECONDS. NO OTHER INITIATING
DEVICES SHALL BE CONNECTED TO THESE CIRCUITS UNLESS
APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION.
EDGE
CONNECT
(FUTURE
USE)
POWER SUPPLY
CONNECTOR
300-04705 or 300-04065
(300-04063 CANADA)
POWER SUPPLY
9V, 2.7A
Be sure to observe
polarity when
connecting the
power supply to
the terminal strip.
IMPORTANT
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
POWER
GND
LYNX TOUCH SERIES SUMMARY OF CONNECTIONS
TIP
TIP
PHONE
RING
TIP
RING
RING
COMPLIES WITH FCC RULES, PART 68
FCC REGISTRATION No. AC3AL05BL5000
RINGER EQUIVALENCE: 0.5B
UL INSTALLATIONS
THE MINIMUM WIRE
SIZE USED FOR
TELEPHONE
INSTALLATIONS
MUST BE #26 GAGE
H/S T
PREMISES
TELEPHONE
H/S R
INCOMING
PHONE LINE
GND
NOTE: THE HARDWIRE ZONE CANNOT BEUSED AS A FIRE ZONE.
HWZ1
WARNING
TO PREVENT RISK OF
SHOCK, DISCONNECT
TELEPHONE LINE
AT TELECOM JACK
BEFORE SERVICING
THIS UNIT
TRIG
TRIGGER OUTPUT (NEG)
(3ma)
LYNX TOUCH SERIES ALSO COMPLIES WITH THE FOLLOWING:
CANADIAN STANDARDS ASSOCIATION (CSA) C22.1,
CANADIAN ELECTRICAL CODE, PART 1, SAFETY STANDARD
FOR ELECTRICAL INSTALLATIONS AND CAN/ULC-S540
INSTALLATION OF RESIDENTIAL FIRE WARNING SYSTEMS.
+9VDC
THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE
PROTECTION ASSOCIATION STANDARDS ANSI/NFPA 70 NATONAL ELECTRIC CODE AND
NFPA 72 NATIONAL FIRE ALARM CODE, CHAPTER 2 (NATIONAL FIRE PROTECTION
ASSOC., BATTERY MARCH PARK, QUINCY, MA 02169). PRINTED INFORMATION
ESCRIBING PROPER INSTALLATION, EVACUATION PLANNING AND REPAIR SERVICE IS TO
BE PROVIDED WITH THIS EQUIPMENT.
LYNX Touch Installation and Setup Guide
Notes: Connection of the fire alarm signal to a fire alarm headquarters or a central station shall be permitted with the
approval of the local authority having jurisdiction. The burglar alarm signal shall not be connected to a police
emergency number. The System must be checked by a qualified technician once every three years
WARRANTY INFORMATION
Fort the latest warranty information, please visit:
www.honeywell.com/security/hsc/resources/wa
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2011 Honeywell International Inc.
www.honeywell.com/security
Ê800-06834MŠ
800-06834
1/11 Rev. A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : E652388
Create Date                     : 2011:03:08 16:29:04Z
Modify Date                     : 2011:03:10 09:16:16-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : E652388
Title                           : Microsoft Word - 800-06834_ii.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2011:03:10 09:16:16-05:00
Producer                        : Acrobat Distiller 4.05 for Windows
Document ID                     : uuid:a328a0b0-2e07-4230-a80a-719991276046
Instance ID                     : uuid:17505d8d-7f15-42a6-a9ba-112aacfb7101
Page Count                      : 72

EXIF Metadata provided by EXIF.tools