Ademco 8DLSL5011 Multi-Band Wireless Modem Module Cartridge User Manual Rev 7B

Honeywell International Inc. Multi-Band Wireless Modem Module Cartridge Users Manual Rev 7B

Users Manual Rev 7B

Lyric-
CDMA
Installation Instructions
Lyric-CDMA Communication Module Installation Guide
For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech
General Information
The Lyric-CDMA Communication Module allows the Lyric Smart Controller to communicate with the Central Station via the
cellular radio network.
NOTE: Before installing the communication module, remove power from the control or use the “Install Cell” mode
described in the Replacing the Module section below.
Installing the Lyric-CDMA Module
1. Install the provided FCC/IC label (P/N 800-19688) on
the control’s case back.
2. Remove bezel from right-hand side of control to
expose the radio module slot To remove bezel, push
upward.
3. Insert the module into the slot. Push firmly to mate the
edge connector.
4. Replace the bezel.
5. Use AlarmNet Direct to enable the Lyric-CDMA
module, configure alarm reporting and module
supervision, and register the module.
Typical FCC/IC Label Location
Removing the Bezel
Installing the Lyric-CDMA Module
Replacing the Module
In the event the module needs to be replaced, the Control must first be put in module replacement (“Install Cell”) mode to
avoid causing a tamper alarm.
1. Select the Install Cell button.
(Security – More Tools enter codeTest Install Cell)
This mode deactivates tamper protection so the side
bezel can be removed without causing an alarm.
2. Remove the side bezel. See diagram above.
3. Remove the screw that secures the module to the
control.
4. Remove the communication module from its
connection slot.
5. Insert the new module into the slot. Push firmly to
mate the edge connector. Replace the securing screw.
6. Replace the bezel.
7. Use AlarmNet Direct to enable the Lyric-CDMA
module, configure alarm reporting and module
supervision, and register the module.
HONEYWELL
PRELIMINARY
PLEASE GO TO BOTTOM OF
THE NEXT PAGE FOR FCC / IC
AGENCY STATEMENTS.
Ê800-191807Š
800-19180 12/14 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2014 Honeywell International Inc.
www.honeywell.com/security
Electrical Specifications
Voltage Input .. 5V (provided by the control panel)
Current
Idle ................ 15 mA, standby
Average ........ 300mA, average transmit
Peak 1.6A peak transmit, 25% duty cycle
FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your
information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for
a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
If using an indoor antenna, have a quality outdoor antenna installed.
Reorient the receiving antenna until interference is reduced or eliminated.
Move the radio or television receiver away from the receiver/control.
Move the antenna leads away from any wire runs to the receiver/control.
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux
conditions suivantes: (1) Cet appareil ne doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris
les interférences causant une réception indésirable.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all
persons and must not be co-located or operated in conjunction with any other transmitter except in accordance with FCC multi-
transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation
IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS
If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer.
TO THE INSTALLER
For the Lyric-CDMA, the external antenna must not exceed a maximum directional gain (including cable loss) of 9.3 dBi at 850 MHz
and 8.2 dBi at 1900 MHz.
SUPPORT & WARRANTY
For the latest documentation and online support information, please go to:
www.security.honeywell.com/hsc/resources/MyWebTech
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
HONEYWELL
PRELIMINARY

Navigation menu