Advance Security TR12 Car Alarm Transceiver User Manual

Advance Security Inc Car Alarm Transceiver Users Manual

Users Manual

PROGRAMMABLE OPTIONS You can program multiple options in one session if you start with the lowest option and continue on to higher options [if needed] without repeating steps #1-3 below. For example, you can follow the programming steps to change Option #2 to “OFF” by pressing the lock button on the remote, then you can continue pressing the program button additional times to get to a high number option and change the setting without having to repeat Steps 1-5. You can only go from low to higher option numbers in one session. To Engage Option Programming: 1. Open hood (ground the Blue wire if no hood pin switch is installed) 2. Turn Key to the ON position 3. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times. 4. Push the valet/program button [again] the number of times that corresponds to the option number desired (1 thru 20). You must get a light flash after each button press. See chart on next page for option list. 5. When you reach the desired programming level, Press button #1, #2, #3 or #4 to change the option. 6. Turn Ignition OFF, Close hood and check for changed features. Change each option individually repeating #1-5.
PROGRAMMABLE OPTION RESET This system provides a reset method to restore all options to FACTORY DEFAULT VALUES as listed in the “Button #2” column of the programmable option chart on pages 18-19. This can be helpful if you have lost track of the option settings on your system, or when you are moving the system from car to car and want a “clean slate”. 1. Open hood (ground the Blue Hood Switch Wire if no hood pin is installed) 2. Turn Key to the ON position 3. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times. 4. Push the valet/program button 25 times. Press carefully, do not lose count! You must get a light flash each time you press the button. If the unit didn’t flash the lights, then the system did not register your press. PROGRAMMABLE OPTION TABLE Option # CS-2205 Alarm Function TX Button #1 TX Button #2 TX Button #3 TX Button #4 1 Horn Pulse Door & Hood Trigger Only *All Functions No Warn-A-Way No Arm/Disarm Pulse 2 Auto lock with Ignition OFF *ON = Lock/Unlock Lock Only Unlock Only 3 Passive/Active Arming ON = Passive Arm *OFF = Active Arm 4 Active Re-Arm ON *OFF 5 Passive Locks ON *OFF 6 Parking Lights on w/Disarm OFF *ON 7 Arm with Ignition ON OFF *ON (Sensors off with Ignition On) ON (Sensors on with Ignition ON)
8 Siren Chirps with Arm/Disarm OFF *ON 9 Override PIN Code ON *OFF 10 Disarm on Trunk pop OFF *ON 11 Open Door Warning 5 seconds *60 seconds 12 Lock/Unlock Pulse 3.5 Sec. *0.80 Sec. 0.50 Sec. Comfort Feature13 Double Unlock Pulse ON *OFF 14 Carjack Enable/Disable ON *OFF 15 Type of Carjack Protection PASSIVE ACTIVE* FULL-TIME 16 Enable Range Check ON *OFF 17 "TEST MODE" Zone 2 & 3 *OFF Zone 1 & 4 18 Panic Mode OFF *ON With Ignition Off 19 Aux Channel #1 Latched *Momentary Reset with Ignition ON Timed 1 to120 Sec. 20 Aux Channel #2 Latched *Momentary Reset with Ignition ON Timed 1 to120 Sec. 21 Aux Channel #3 Latched *Momentary Reset with Ignition ON Timed 1 to120 Sec. 22 Aux Channel #4 Latched *Momentary Reset with Ignition ON Timed 1 to120 Sec. 23 Option Reset to Default (*) Values Reset options TRANSCEIVER / REMOTE CONTROL PROGRAMMING 1. Turn key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times. Press buttons #1 (Lock) & #2 (Unlock) together at the same time of each transceiver to be learned. You should get 2 light flashes indication the unit is waiting for a 2nd code, then press button #1 & #2 of a second transmitter or transceiver, the unit will flash 3 times indicating its waiting for the 3rd code and lights will flash 4 times for 4th code. If all 4 codes are learned, the unit will automatically exit code learning mode.
IGNOFFWAIT FOR4 FLASHESPRESS 4X'sFLASH 2, 3, or 4 X's(BLUE WIRE GROUNDED)2-WAY SYSTEMS &IGNOFFPRESS TOGETHERLOCK &UNLOCK"SideKick" REMOTESCOMPLETE
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

Navigation menu