Advance Security TR12 Car Alarm Transceiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	529547
Application ID	8PXLdu7yC/yFzCnucgrOGg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.84kB (35525 bits)
Date Submitted	2005-04-07 00:00:00
Date Available	2005-04-07 00:00:00
Creation Date	2005-04-06 11:27:44
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2005-04-06 11:27:44
Document Title	Users Manual

PROGRAMMABLE OPTIONS
You can program multiple options in one session if you start with the lowest option and continue
on to higher options [if needed] without repeating steps #1-3 below. For example, you can follow
the programming steps to change Option #2 to “OFF” by pressing the lock button on the remote,
then you can continue pressing the program button additional times to get to a high number option
and change the setting without having to repeat Steps 1-5. You can only go from low to higher
option numbers in one session.
To Engage Option Programming:
1. Open hood (ground the Blue wire if no hood pin switch is installed)
2. Turn Key to the ON position
3. Press program / valet button 5 times, after a few seconds the unit will flash the
lights 5 times.
4. Push the valet/program button [again] the number of times that corresponds to
the option number desired (1 thru 20). You must get a light flash after each
button press. See chart on next page for option list.
5. When you reach the desired programming level, Press button #1, #2, #3 or #4 to
change the option.
6. Turn Ignition OFF, Close hood and check for changed features. Change each
option individually repeating #1-5.
PROGRAMMABLE OPTION RESET
This system provides a reset method to restore all options to FACTORY DEFAULT
VALUES as listed in the “Button #2” column of the programmable option chart on
pages 18-19. This can be helpful if you have lost track of the option settings on
your system, or when you are moving the system from car to car and want a “clean
slate”.
1. Open hood (ground the Blue Hood Switch Wire if no hood pin is installed)
2. Turn Key to the ON position
3. Press program / valet button 5 times, after a few seconds the unit will flash the
lights 5 times.
4. Push the valet/program button 25 times. Press carefully, do not lose count! You
must get a light flash each time you press the button. If the unit didn’t flash the
lights, then the system did not register your press.
PROGRAMMABLE OPTION TABLE
Option
CS-2205 Alarm
Function
TX Button #1
TX Button #2
TX Button #3
TX Button #4
Horn Pulse
Door & Hood
Trigger Only
*All Functions
No Warn-AWay
No Arm/Disarm
Pulse
OFF
*ON =
Lock/Unlock
Lock Only
Unlock Only
ON = Passive Arm
*OFF = Active Arm
Auto lock with
Ignition
Passive/Active
Arming
Active Re-Arm
ON
*OFF
Passive Locks
ON
*OFF
Parking Lights
on w/Disarm
OFF
*ON
Arm with
Ignition ON
OFF
*ON (Sensors off
with Ignition On)
ON
(Sensors on
with Ignition
ON)
8
10
11
12
13
14
Siren Chirps
with Arm/Disarm
Override PIN
Code
Disarm on Trunk
pop
Open Door
Warning
Lock/Unlock
Pulse
Double Unlock
Pulse
Carjack
Enable/Disable
OFF
*ON
ON
*OFF
OFF
*ON
5 seconds
*60 seconds
3.5 Sec.
*0.80 Sec.
ON
*OFF
ON
*OFF
15
Type of Carjack
Protection
PASSIVE
ACTIVE*
16
Enable Range
Check
ON
*OFF
17
"TEST MODE"
Zone 2 & 3
*OFF
18
Panic Mode
OFF
*ON
19
Aux Channel #1
Latched
*Momentary
20
Aux Channel #2
Latched
*Momentary
21
Aux Channel #3
Latched
*Momentary
22
Aux Channel #4
Latched
*Momentary
23
Option Reset to
Default (*)
Values
0.50 Sec.
Comfort Feature
FULL-TIME
Zone 1 & 4
With Ignition
Off
Reset with
Ignition ON
Reset with
Ignition ON
Reset with
Ignition ON
Reset with
Ignition ON
Timed 1 to120
Sec.
Timed 1 to120
Sec.
Timed 1 to120
Sec.
Timed 1 to120
Sec.
Reset options
TRANSCEIVER / REMOTE CONTROL PROGRAMMING
1. Turn key to the ON position.
2. Press Programming button 4 times, then after a few seconds the unit will flash
the parking lights 4 times.
Press buttons #1 (Lock) & #2 (Unlock) together at the same time of each transceiver
to be learned. You should get 2 light flashes indication the unit is waiting for a 2nd
code, then press button #1 & #2 of a second transmitter or transceiver, the unit will
flash 3 times indicating its waiting for the 3rd code and lights will flash 4 times for 4th
code. If all 4 codes are learned, the unit will automatically exit code learning mode.
IGN
OFF
WAIT FOR
4 FLASHES
(BLUE WIRE GROUNDED)
PRESS 4X's
2-WAY SYSTEMS &
"SideKick" REMOTES
FLASH 2, 3, or 4 X's
LOCK &
UNLOCK
PRESS TOGETHER
IGN
OFF
COMPLETE
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions.
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that
may cause undesired operation.
Per FCC 15.21, you are cautioned that changes or modifications not expressly
approved by the part responsible for compliance could void the user’s authority to
operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2005:04:06 11:27:44+08:00
Modify Date                     : 2005:04:06 11:27:44+08:00
Page Count                      : 5
Creation Date                   : 2005:04:06 03:27:44Z
Mod Date                        : 2005:04:06 03:27:44Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Metadata Date                   : 2005:04:06 03:27:44Z

EXIF Metadata provided by EXIF.tools