Advance Security TR34 Car Alarm Transceiver User Manual CA Elite 6 series Install rev A 4 13 09

Download:
Mirror Download [FCC.gov]
Document ID	1182700
Application ID	mZPvdnMSzv7g3DMhQzvfpg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	82.67kB (1033373 bits)
Date Submitted	2009-10-13 00:00:00
Date Available	2009-10-13 00:00:00
Creation Date	2009-08-20 12:16:46
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2009-10-09 18:03:39
Document Title	CA Elite 6 series Install rev A 4-13-09
Document Creator	Adobe PageMaker 7.0
Document Author:	pburdick

PROFESSIONAL
SERIES
Security and Remote Start Installation Guide
for models:
CA 6150
CA 6550
2009 Audiovox Electronics Corporation. All rights reserved.
Table of Contents
Before You Begin ...................................................................................... 4
Wire Connection Guide ........................................................................... 5
5 Pin Main Harness ................................................................................... 7
6 Pin Start Harness ................................................................................... 8
6 Pin Output Harness ............................................................................. 10
8 Pin Input Harness ................................................................................. 11
2 Pin Door Lock Output Harness ........................................................... 14
Additional Ports ...................................................................................... 18
Antenna / LED / Programming Port ....................................................... 18
DBI Port .................................................................................................... 18
Set Up & Programming .......................................................................... 19
Transmitter Programming ........................................................................ 19
Manual Feature Programming ................................................................. 19
Programming Feature Banks .................................................................. 20
Tach Programming .................................................................................. 21
Adjusting the Shock Sensor .................................................................. 22
Testing the Shock Sensor ...................................................................... 22
Dome Light Delay / Theater Dimming ..................................................... 22
Chirp Delete - User Accessible .............................................................. 22
2009 Audiovox Electronics Corporation. All rights reserved.
Feature Descriptions ............................................................................. 23
Transmitter Button Functions ............................................................. 27
Security Trigger Zones ......................................................................... 28
Remote Start Shutdown Diagnostics ................................................ 28
System Layout ......................................................................................... 29
2009 Audiovox Electronics Corporation. All rights reserved.
BEFORE YOU BEGIN
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal
surfaces
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical Support (800) 421-3209
or go to
http://techservices.codesystems.com
2009 Audiovox Electronics Corporation. All rights reserved.
5 Pin Main Harness
6 Pin Start Harness
6 Pin Output Harness
2009 Audiovox Electronics Corporation. All rights reserved.
8 Pin Input Harness
2 Pin Lock Output Harness
2009 Audiovox Electronics Corporation. All rights reserved.
5 Pin Main Harness
WHITE/RED
PARKING LIGHT INPUT
WHITE
PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle’s light switch.
Verification: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
BLACK
GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
BROWN
SIREN OUTPUT ( + )
Locate a suitable mounting location in the engine compartment for the siren, away
from moving parts.
With the bell of the siren aiming downwards, secure the siren in place using self
tapping screws, being careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall
and connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.
2009 Audiovox Electronics Corporation. All rights reserved.
5
RED
BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6 Pin Start Harness
PURPLE
STARTER OUTPUT ( + )
Locate the vehicle starter wire.
Verification: This wire registers voltage only when the key is turned to the
START position. Cut the vehicle's starter wire in half when installing the
starter kill relay.
Verification after starter wire is cut:
KEY SIDE of starter wire registers voltage when the key is turned to the
START position.
MOTOR SIDE of starter wire registers no voltage.
Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE of the vehicle
starter wire when installing the starter kill relay.
RED
BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
2009 Audiovox Electronics Corporation. All rights reserved.
3
RED
BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
PINK
IGNITION 1 ( + )
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the PINK wire to the vehicle’s Ignition wire.
This wire is also used for Ignition 1 Output.
PINK/WHITE
IGNITION 2 ( + )
Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START (or CRANK) position.
Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.
Programmable output: IGN, ACC, Start.
ORANGE
ACCESSORY 1 ( + )
Locate the vehicle’s accessory wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START (or CRANK) position.
Connect the ORANGE wire to the vehicle’s accessory wire.
2009 Audiovox Electronics Corporation. All rights reserved.
6 Pin Output Harness
BROWN/BLACK
HORN OUTPUT ( - )
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 500mA.
BLUE/BLACK
IGNITION 3 / ACTIVE OUTPUT ( - )
The Active Output/Ignition 3 output wire provides a ground output when the remote
start function is activated and remains until 4 seconds after the remote start is
shutdown. The Ignition 3 output wire can be used for several functions listed
below. If this wire will be used for multiple application's a 1 amp diode is required
in-line with the stripe facing the control module.
Factory transponder (coded key) bypass.
General Motors VATS bypass, see the following diagram. Use an SPDT relay (not
supplied).
Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied).
Matching Value
Resistor
87
Fused +12 Volt
Battery Source
87a
85
86
BLUE/BLACK ActiveOutput
Wire
30
VATS Wire #2, WHITE or VIOLET/WHITE
VATS Wire #1, WHITE or WHITE/BLACK
Accessory 2/3 output, see the following diagram. Use an SPDT relay (not
GM VATS
supplied).
Ignition Switch
X CUT
VATS Control Module
Ignition 3
Accessory 2/3
Fused +12 Volt
Battery Source
Fused +12 Volt
Battery Source
87
87
Jump To PINK
Ignition Output
Wire From
Control Module
87a
85
86
30
To Vehicle's 2nd or
3rd Ignition Wire
10
BLUE/BLACK Active Output
Wire
Jump To ORANGE
Accessory Output
Wire From
Control Module
87a
85
86
BLUE/BLACK Active Output
Wire
30
To Vehicle's 2nd or 3rd
Accessory Wire
2009 Audiovox Electronics Corporation. All rights reserved.
3
VIOLET/BLACK
AUX 1
This wire provides a ( - ) 500mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
RED/WHITE
TRUNK RELEASE OUTPUT ( - )
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when the trunk
release is activated.
This is a low current output, 500mA.
LT GREEN/BLACK
FACTORY DISARM /
PULSE BEFORE START ( - )
This wire will supply a ( - ) 500mA pulse both upon disarming the system and when
the remote start feature is activated. Locate the factory perimeter alarm disarm
wire from the key cylinder inside the drivers door.
Verification: This wire registers ground if the key is turned to the unlock
position in the driver’s door cylinder.
Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.
ORANGE
GROUND WHEN ARMED OUTPUT ( - )
This wire will have a continuous ( - ) 500mA output when the system is Armed. This
wire is typically used for controlling window modules or additional sensors.
8 Pin Input Harness
BLUE/WHITE
INSTANT TRIGGER INPUT ( - )
This wire is a GROUND input for an external sensor or secondary pin switch.
Verification: This wire when connected will trigger the security system.
2009 Audiovox Electronics Corporation. All rights reserved.
11
2
GREEN
DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
PURPLE
DOOR TRIGGER INPUT ( + )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register positive voltage (POS) when the door is
opened and the interior light is on. This wire will
register ground or "0" Volts when the door is closed and the interior light is
off.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
WHITE/BLUE
EXTERNAL START INPUT ( - )
This wire will activate the Remote Start function when a GROUND pulse is applied to it
from an external device.
GRAY
HOOD PIN INPUT ( - )
Install a Hood Pin Switch and connect to the GRAY wire. This connection is
required for Remote Start.
Verification: This wire when connected will register ground when the
vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
12
2009 Audiovox Electronics Corporation. All rights reserved.
6
BLACK/WHITE
NEUTRAL SAFETY INPUT ( - )
Locate the vehicle’s neutral safety circuit.
Verification: This wire registers ( - ) voltage when the vehicle’s gear selector
is in park or neutral.
Connect the BLACK/WHITE neutral safety input wire to the neutral safety wire of
the vehicle or an optional toggle switch. The remote start feature will not operate
unless this input is supplied with a ground source.
BROWN/RED
BRAKE INPUT ( + )
Locate the vehicle’s brake light wire at the brake pedal mounted switch.
Verification: This wire registers positive voltage when the brake pedal is
pressed.
Connect the BROWN/RED wire to the vehicle’s brake light wire.
PURPLE/WHITE
TACH INPUT
Locate the vehicle’s ignition coil or fuel injector in the engine compartment.
Verification: Test using the following procedure:
1.
2.
3.
4.
5.
Set voltmeter to AC VOLTS.
Attach positive lead of a volt meter to a constant 12 volt source.
Attach negative lead of a volt meter to the wire to be tested.
Start the engine.
Have someone press on the gas pedal slightly as you monitor the meter. If
connected to the correct wire, the voltage reading will increase as the engine’s
RPM increases.
Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil
or fuel injector.
2009 Audiovox Electronics Corporation. All rights reserved.
13
2 Pin Lock Output Harness
BLUE
UNLOCK ( - )
GREEN
LOCK ( - )
The door lock / unlock outputs are designed to control several different types of
systems which may require additional parts. Please review the wire and location
chart to see which type of door lock system is in your vehicle. The most common
types are shown in the following diagrams.
Negative Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: These wires will register ground when the Lock and Unlock
switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Negative Locks:
GREEN (-) Lock Output
Lock
Vehicle Door Lock
Control Relays
Unlock
BLUE (-) Unlock Output
14
2009 Audiovox Electronics Corporation. All rights reserved.
Positive Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: These wires will register positive voltage when the Lock and
Unlock switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Positive Locks:
Fused +12 Volt
Battery Souce
87
87a
86
85
GREEN (-) Lock Output
30
Lock
Fused +12 Volt
Battery Souce
Vehicle Door Lock
Control Relays
87
Unlock
87a
86
85
BLUE (-) Unlock Output
30
Reverse Polarity Locks (5-Wire Door locks)
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: These wires will rest at ground and register positive
voltage when the Lock and Unlock switches are activated.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
Reverse Polarity Locks:
Fused +12 Volt
Battery Souce
87
87a
86
85
GREEN (-) Lock Output
30
Lock
To Door Lock Motor
Cut
Unlock
Fused +12 Volt
Battery Souce
87
87a
86
85
BLUE (-) Unlock Output
30
To Door Lock Motor
Cut
2009 Audiovox Electronics Corporation. All rights reserved.
15
Negative Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: This wire will show variable ground when the switch is activated.
Please consult the wire and location chart for specific resistor values for
your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
Multiplex Locks:
Ground
87
87
87a
GREEN (-) Lock Output
86
85
87a
Fused +12 Volt
Battery Source
86
85
BLUE (-) Unlock Output
30
30
Resistor
Lock
Vehicle Door Lock
Control Relays
Unlock
Positive Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: This wire will show variable positive voltage when the switch is
activated. Please consult the wire and location chart for specific resistor
values for your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
Multiplex Locks:
87
87
87a
GREEN (-) Lock Output
86
85
Fused +12 Volt
Battery Source
Lock
87a
86
85
BLUE (-) Unlock Output
30
30
Resistor
Vehicle Door Lock
Control Relays
Unlock
16
2009 Audiovox Electronics Corporation. All rights reserved.
Adding Aftermarket Actuators
After installing aftermarket actuators, (not supplied). Connect the GREEN and
BLUE wires shown in the diagram below using (2) SPDT relays (not supplied).
Fused +12 Volt
Battery Source
87
Door Lock
Actuator
87a
GREEN (-) Lock Output
85
86
30
Chassis
Ground
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
Chassis
Ground
2009 Audiovox Electronics Corporation. All rights reserved.
17
Additional Ports
Antenna / LED / Programming Port
Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield
that will not block the driver's vision. A good location is usually high on the
windshield near the rear view mirror. Be careful not to mount the antenna/receiver
on any metallic window film, as this will effect system range. Route the antenna/
receiver cable to the control module and plug into the antenna port.
Data Bus Interface Port
This 4 pin port is used for Flashlogic Door Lock and Transponder Databus
Interfaces to communicate with the vehicle's Databus. When using the DBI port to
control the Flashlogic Door Lock and Transponder Interface modules the
following options may be available. Please refer to the D2D (Data to Data)
function list available per vehicle on the tech service web site.
Tach Input
Brake Safety Shut Down
Door Trigger
Trunk/Hatch Open
Door Lock Control
Passlock / Passkey Interface (GM Only)
Dome Light Supervision
Transponder Interface Activation
Factory Alarm Arm / Disarm
Diesel Glow Plug Input
Manual Arm / Disarm Inputs (factory keyless controls system)
18
2009 Audiovox Electronics Corporation. All rights reserved.
Set Up & Programming
Transmitter Programming - Feature Bank 1 - 3 chirps
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Press 1 button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
6. Pressing the override button at anytime during programming will advance to the
next bank.
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
Transmitter programming for 2 Car Mode *2 way system only:
1. Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the
owners manual for 2 car operation)
2. Follow the steps above for transmitter programming.
NOTE: 2 car mode requires an additional security system installed in a second
vehicle.
Manual Feature Programming - Feature Bank 2 - 4 chirps
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2, 3 or 4, which is (4) four, (5)
five, and (6) six chirps.
5. Use the transmitter
button to scroll through the selections in each feature
bank, the system will chirp to match the feature number.
6. Press the transmitter
button to change the desired feature. The LED will
flash indicating the changed feature.
2009 Audiovox Electronics Corporation. All rights reserved.
19
Defaulting All Features: Pressing the
button anytime while in any of the
feature banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the
ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.
Feature Bank 1 - 3 Chirps
Transmitter Programming
Refer to transmitter programming.
20
2009 Audiovox Electronics Corporation. All rights reserved.
Tach Programming
The unit will not operate unless tach is programmed or tachless option is
turned ON. If an attempt is made to start the vehicle via the remote start without
first programming tach, the unit will flash the parking lights 7 times indicating tach
has not been learned and stored. If the tach rate is not properly programmed to
the specific vehicle, the unit may not realize that the vehicle is running in certain
instances and reengage the starter motor.
The Remote Start unit will learn the tach rate of most vehicle's single coil, multiple coil
packs, or single injector. To learn tach:
1. Turn the ignition key to the ON position.
2. Press and release the valet/override button 3 times.
3. Immediately turn the ignition key OFF.
4. Press and hold the valet/override button, then start the vehicle using the
key.
5. When the unit senses the tach signal, the parking lights will begin to flash.
6. Allow the vehicle to settle to a normal idle speed.
7. Release the valet/program push-button switch. The parking lights will
turn on for 2 seconds indicating that the learned tach signal is stored and
the unit has exited tach learn mode.
2009 Audiovox Electronics Corporation. All rights reserved.
21
NOTE: If the unit fails to learn tach rate due to an improper tach connection or a
poor tach source, the parking lights will not flash. To correct this situation, locate
and connect the PURPLE/WHITE wire to the proper tach signal, and then repeat
the tach learn routine.
Adjusting the Shock Sensor
1. Increase sensitivity by turning the adjustment dial clockwise.
2. Decrease sensitivity by turning the adjustment dial counter clockwise.
Testing the Shock Sensor
Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike
the vehicles bumper.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system will
respond with 1 chirp for ON or 2 chirps for OFF.
Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed (60
second max) for vehicles with a dome light delay or theater dimming feature. Once
programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has entered
DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the dome
light turns off, the system will then add 2 seconds and then exit the learning
mode.
4. The LED will begin to flash indicating the system has exited the learning
mode and is now armed.
22
2009 Audiovox Electronics Corporation. All rights reserved.
Feature Descriptions
Feature Bank 2 - Security
1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.
ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/
unlock a second time will activate the arm/disarm chirps respectively. The
system will only sound the arm/disarm chirps upon a second press of the
lock/unlock buttons.
OFF - normal arm/disarm chirps upon the first press of lock/unlock.
2 - Passive Locks: Determines manual or automatic locking of the vehicle’s
doors.
Active - Requires use of the transmitter to lock the vehicle’s doors.
Passive - Automatically locks the vehicle’s doors 1 minute after the last door
is closed
3 - Passive Arming: Determines manual or automatic locking of the vehicle’s
doors.
Active - Requires use of the transmitter to arm the security system.
Passive - Automatically arms the security system 1 minute after the last door
is closed
4 - Siren / Horn: This feature selects which output(s) will sound the system’s
arm/disarm chirps. This feature does not effect the triggered state of the security
system and during a triggered cycle, both the siren and horn outputs will activate
respectively.
5 - Security: Controls security functionality - ON / OFF.
ON - Full security functionality.
OFF - The security system does not trigger. Panic, Remote Start and all
other convenience features operate as normal.
6 - Hi Jack: Controls hi jack mode - ON / OFF.
OFF - Standard security system operation.
ON - Enables Hi Jack mode functionality as described in the owners manual
2009 Audiovox Electronics Corporation. All rights reserved.
23
Feature Bank 3 - Output Control
1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock
output wires.
1 Second - Single 1 second lock pulse, single 1 second unlock pulse.
3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.
1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1
second unlock pulse.
30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double
1 second unlock pulse.
Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1
second unlock pulse.
2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarm
output.
Factory Disarm - Single 1 second pulse with unlock and remote start
activation.
2nd Unlock - Single 1 second pulse with 2nd press of unlock only.
Start Status - Continuous ( - ) output during the remote start cycle.
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled
ON or OFF.
OFF - Door locks not activated by ignition.
Lock and Unlock - Doors lock when ignition is turned on and unlock when
ignition is turned off.
Lock Only - Doors lock when ignition is turned on.
Unlock Only - Doors unlock when ignition is turned off.
4 - Horn Output Timing: Control the minimum horn pulse time in milli seconds,
some vehicle will require a longer pulse to activate the factory horn.
16mS
10mS
30mS
40mS
50mS
5 - Real Panic: Controls the panic out when triggered from the transmitter.
ON - Randomized horn honks when panic is triggered.
OFF - Standard pattern horn honks when panic is triggered.
24
2009 Audiovox Electronics Corporation. All rights reserved.
6 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
Dome Light Output - Output is used for illuminated entry and is not controlled
by the AUX 1 function of the transmitter.
Feature Bank 4 - Remote Start Control
1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or OFF.
2 - Run Time: Controls the time in minutes that the vehicle will stay running
under control of the remote start until the system times out. The system may also
be shut down at any time by use of the transmitter or system shutdowns.
3 - Running Lights: Controls the WHITE parking light output wire during remote
start.
Steady - Parking lights constant during the remote start cycle.
Flashing - Parking lights flash at a slow pace during the remote start cycle.
4 - Tach Mode: Determines how the system monitors the engine running during
remote start.
Tach - Hard wired directly to the tach wire of the vehicle to monitor AC
voltage.
Tachless (Crank Average/Voltage) - Determines crank time by averaging the
last 8 times the vehicle was started with the key and then monitors the
change in voltage after remote start.
Hybrid (Crank Average / No Voltage) - Determines crank time by averaging
the last 8 times the vehicle was started with the key.
DBI Port - Monitors the vehicle’s tach rate through an interface module
connected to the DBI port.
2009 Audiovox Electronics Corporation. All rights reserved.
25
5 - Voltage Level: The voltage variance for remote start when set to tachless.
(see tach mode)
HIGH - The variance in battery voltage from before the remote start
is activated to after the engine is running must be greater than 0.5 volts.
LOW - The variance in battery voltage from before the remote start
is activated to after the engine is running may be less than 0.5 volts.
6 - Crank Time: Preset output times for the PURPLE starter wire.
7 - Crank Average / Crank Time: The length of time in which the remote start
will crank the vehicle’s starter.
Crank Average - Determines crank time by averaging the last 8 times the
vehicle was started with the key.
Preset Time - Preset starter output time. (see crank time)
8 - Gas / Diesel: Selects engine type and delay time for the starter output wire
during remote start activation.
Gas - Gasoline engine, no delay for the starter output wire.
10 Second Delay - Diesel engine, delays the starter output wire for 10
seconds after the ignition has been powered up by the remote start.
15 Second Delay - Diesel engine, delays the starter output wire for 15
seconds after the ignition has been powered up by the remote start.
20 Second Delay - Diesel engine, delays the starter output wire for 20
seconds after the ignition has been powered up by the remote start.
45 Second Delay - Diesel engine, delays the starter output wire for 45
seconds after the ignition has been powered up by the remote start.
9 - Single / Double Pulse Start: Switches the remote start activation between
a single or double press from the transmitter.
10 - IGN 2 Output: Programmable high current output.
Ignition 2 - Ignition output during remote start.
Accessory - Accessory output during remote start.
Start / Crank - Crank output during remote start.
26
2009 Audiovox Electronics Corporation. All rights reserved.
11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for
the programmed time and shut down every 2 or 3 hours.
12 - Turbo Timer: When activated, the vehicle will run for the programmed time.
OFF
1 Minute
3 Minutes
5 Minutes
Transmitter Button Functions
* 2 Way Transmitter - CA 6550 Only
2009 Audiovox Electronics Corporation. All rights reserved.
27
Security Trigger Zones
If the security system has been triggered the LED will flash one of the patterns
below indicating the zone.
LED FLASHES
TRIGGER ZONE
2 Flashes
Hood / Trunk Input
3 Flashes
Door Input
4 Flashes
Shock Sensor
5 Flashes
Ignition Input
Remote Start Shutdown Diagnostics
If the remote start shuts down or fails to start, the parking lights will flash one of
the patterns below indicating the shutdown input.
To manually enter diagnostics and view the last shutdown, turn the ignition ON
and press and release the
button.
LED FLASHES
SHUTDOWN ZONE
3 Flashes
Hood Input
Brake Input
28
4 Flashes
Remote Start Valet Mode
7 Flashes
Tach not learned / Crank Average not learned
2009 Audiovox Electronics Corporation. All rights reserved.
CA 6150 / CA 6550
2009 Audiovox Electronics Corporation. All rights reserved.
29
PARKING LIGHT INPUT
PARKING LIGHT OUTPUT
GROUND
SIREN OUTPUT ( + )
BATTERY 12V ( + )
HORN OUTPUT ( - )
IGNITION 3 / ACTIVE OUTPUT ( - )
AUX 1 ( - )
TRUNK RELEASE OUTPUT ( - )
FACTORY DISARM / PULSE BEFORE START ( - )
GROUND WHEN ARMED ( - )
UNLOCK ( - )
LOCK ( - )
WHITE/RED
WHITE
BLACK
BROWN
RED
BROWN/BLACK
BLUE/BLACK
VIOLET/BLACK
RED/WHITE
LT GREEN/BLACK
ORANGE
BLUE
GREEN
SHOCK SENSOR PORT
DBI PORT
STARTER OUTPUT - MOTOR SIDE ( + )
BATTERY 12V ( + )
BATTERY 12V ( + )
IGNITION 1 ( + )
IGNITION 2 ( + )
ACCESSORY 1 ( + )
ANTENNA
INSTANT TRIGGER INPUT ( - )
DOOR TRIGGER INPUT ( - )
DOOR TRIGGER INPUT ( + )
EXTERNAL START INPUT ( - )
HOOD INPUT ( - )
NEUTRAL SAFETY INPUT ( - )
BRAKE INPUT ( + )
TACH INPUT
PURPLE
RED
RED
PINK
PINK/WHITE
ORANGE
IVU(EUT)
LED
VALET
BLUE/WHITE
GREEN
PURPLE
WHITE/BLUE
GRAY
BLACK/WHITE
BROWN/RED
PURPLE/WHITE
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference
that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
30
2009 Audiovox Electronics Corporation. All rights reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2009:10:09 18:03:39+08:00
Create Date                     : 2009:08:20 12:16:46-04:00
Subject                         : CA Elite 6 series Install rev A 4-13-09
Page Count                      : 31
Has XFA                         : No
About                           : uuid:3abc6ec0-9c79-4df6-b220-e0438e9aebf9
Producer                        : Acrobat Distiller 6.0 (Windows)
Keywords                        : 
Mod Date                        : 2009:10:09 18:03:39+08:00
Creation Date                   : 2009:08:20 12:16:46-04:00
Author                          : pburdick
Creator Tool                    : Adobe PageMaker 7.0
Metadata Date                   : 2009:10:09 18:03:39+08:00
Document ID                     : uuid:28a09272-42cc-421f-995c-bb309a1f2e8f
Format                          : application/pdf
Description                     : CA Elite 6 series Install rev A 4-13-09
Title                           : CA Elite 6 series Install rev A 4-13-09
Creator                         : pburdick

EXIF Metadata provided by EXIF.tools