Advance Security TR61 Remote Control User Manual 140904 Final SL 62oper both sides Draft
Advance Security Inc Remote Control 140904 Final SL 62oper both sides Draft
Users Manual
REMOTE CONTROL TRANSMITTER:
TRANSMITTER OPERATION
Transmitter
Button System Function Remark
Lock Doors & Arm System
Panic function Press and Hold for 3 seconds.
Press Trunk button to stop
panic function
Car Locator Press when in armed mode
- Arm and Delete The 2 Stage
Shock Sensor Press twice within 3 seconds.
Pass will appear on the remote
- Arm System and Hidden
Alarm Function
Press within 3 seconds and Hold
button for 2 seconds
+ Silent Arming / Disarming Ignition in "off" position.
+ Active Anti Car-Jacking Mode
Ignition in "on" position press
and hold for 2 seconds
Unlock Doors & Disarm
System
- Two Steps Door Unlock &
Disarm System(optional) Press twice within 3 seconds.
Trunk Release (Channel 3) Press and Hold for 2 seconds
- Passive Arming By-pass While the system Disarmed.
Activate or Turn Off The
Remote Start Press button once. Press
Twice if set to start safety mode
+ Channel # 4 Timer Output (4)
Channel 4
II Switch to 2nd car operation
For 1-way TX only, Press & hold
until TX LED on
ACTIVE LOCKING
–
LOCK
& ARMING
:
1. Press
button on transmitter.
2. The siren or horn will chirp once and the parking lights will flash once indicating that the system is now
armed. The vehicle doors will lock upon arming when interfaced with the security system.
Note: Defective sensor reminder: If the siren or horn sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. (OPTIONAL)
SILENT LOCKING AND UNLOCKING: ARMING / DISARMING: Press the
+
button together on the
transmitter to LOCK or UNLOCK your security system, No chirp sound will be heard; arm / disarm confirmation
will be through the vehicles parking lights only.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Pressing the
button on the transmitter twice within 3
seconds will arm the security system and by-pass the shock sensor. The system will chirp one additional time to
confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming cycle
PASSIVE LOCKING OR ARMING: Programmable
Active arming / disarming is controlling your security system via the remote transmitter. This security system is
equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the
last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any
door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle
entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren or horn will
chirp [1] time and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING: Programmable
The vehicle doors will automatically lock after passive arming cycle has been completed.
PASSIVE ARMING BY-PASS: While the system is disarmed, Press the button twice, the system will
respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as
long as you wish. To exit passive by-pass, press the transmitter or buttons and the system will return to
normal status.
ACTIVE UN-LOCKING – UNLOCK & DISARM:
1. Press the
button on the transmitter.
2. The siren or horn will chirp twice and parking lights will flash twice to indicate that the security system is now
disarmed. The vehicle doors will unlock when interfaced with the security system.
IGNITION CONTROL DOOR LOCKS.
If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the
vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned
“OFF”.
TRUNK RELEASE: Press and hold button on transmitter for three seconds to remote control the trunk
release or other electric devices.
CAR LOCATOR: Press the button on the transmitter when the vehicle is in the armed / locked mode to active
car locator function. The siren or horn will chirp 6 times. The parking light will flash 12 times, allowing you to
easily locate your car.
VALET MODE: (System is in Disarm Mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions
and remote start functions are bypassed, however, the remote panic feature and remote door locks will remain
operational. To use the valet mode, the system must first be disarmed either by using your remote transmitter,
or by operating the Manual Override sequence.
Get into/out valet mode using the ignition key.
Enter Valet Mode:
a). Under disarm mode, turn the ignition to “ON\OFF\ON” position.
b). Press and hold valet switch for 3 seconds until the LED turns ON solid. The LED will remain on as long
as the system is in 'valet mode'.
Exit Valet Mode:
a). Turn ignition 'ON\OFF\ON'.
b). Push and hold valet switch for 3 seconds, The LED will turn off indicate the system are exiting the
valet mode.
Model IUV711A
The lock icon will be displayed
when the door are locked.
The unlock icon will
be displayed when the
door are unlocked
Valet Mode
All the function shall be
temporarily on hold.
Driver paging
Someone is paging
you from of your
vehicle
Warn Away trigger
Trigger on Shock Sensor
Shock Sensor Trigger
Trigger on Shock Sensor
Hood Trigger
Hood is illegally opened
Trunk Trigger
Trunk is illegally opened
Door Trigger
Doors are illegally opened
Sensor Bypass
Sensor bypass under Arm
mode
Ignition Trigger (icon flash)
Ignition switch is illegally
turned on
Button Lock (icon on)
Remote Transmission
You are transmitting the
signal to control unit
In – Range Indicator
You are within the range
of the remote control.
2nd Car Operation
System trigger
Activate Channel 3 (Trunk
Release).
0 :00
Parking Meter
Reminder when time is up
for parking
CH 4
Activate Channel 4
CH 5
Activate Channel 5
12:00
Time Monitor
Low Battery
You have to replace
battery of remote control.
Alarm Clock
Power Save (battery icon
full bar flash)
Melody Mode
Remote Control alert
user through melody sound
Vibration Mode
Remote Control vibrates
when the system is
triggered
Engine Cranking
Your vehicle engine
Cranking by remote
control
Engine Running
Your vehicle's engine
is running
Timer Control Start
Engine start automatically
every 2 or 3 hours.
Manual Gear Mode
programmed
STANDARD LCD ICON CONFIGURATIONS
:
BATTERY REPLACEMENT:
CR2032 x 2 PCS battery powers the Remote Transmitter. When the power of the
battery weakens a icon shall be displayed on the LCD screen. When the old
batteries are replaced, there will be beep sounds indicate the power is up of the
transmitter.
The One-way remote is powered by two CR2016 Batteries.
TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press button once on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will turn on and the climate
controls will activate and adjust the vehicle’s interior temperature to your preset setting. (While the
vehicle is running, the “ ” icon and the “minutes” digit on the LCD screen will flash and the will indicate
countdown timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.)
5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit
shuts off the countdown timer will turn off and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions
exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The gear selector is in any gear other than “PARK” or “NEUTRAL”
4. The system in valet mode.
5. Release the parking (hand) brake. (For Standard Transmission Gear Vehicle or Turbo Timer Mode)
6. The system is failed in engine start memorize set up (For Standard Transmission Gear Vehicle.)
7. If the vehicle failed to start, the above status will flash on the LCD screen
SAFE START (Child safety mode)
Factory default is set to press the button once on the transmitter to start the vehicle. You can program
this feature to eliminate an accidental remote start:
1. The user presses the transmitter buttons twice within 3 seconds to start the vehicle. or
2. The user presses the transmitter and buttons at the same time to start the vehicle.
NOTE: Contact your installing dealer to activate this feature.
OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:
To operate the vehicle while the engine is running from the remote start,
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but
would like to leave the motor running and the climate control on.
1. Before turning off the engine, press the button once on the transmitter and the LED indicator will
flash 3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
.
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
1. Press button once on the remote transmitter under the remote start mode.
2. Move the optional remote start enable toggle switch to OFF position. (If installed)
3. Press the brake pedal
The vehicle will shut down and turn off the parking light to indicate the engine has stopped.
4. Pull down the hand brake. (for Standard Transmission Gear Vehicle)
The vehicle will shut down and turn off the parking light to indicate engine stopped
SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the engine will not start or will shut
down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The parking (hand) brake is released (For Turbo Timer Mode)
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Press button on the remote transmitter under remote start mode.
7. The system trigger.
8. The vehicle refused to start running after {3} unsuccessful attempts.
IMPORTANT
: Remote Start should be used only in open areas, Never start and run
the vehicle in an enclosed space for any extended period. Carbon Dioxide is
dangerous to Humans, pets and animals within the enclosed spaces.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the
alarm in case of emergency.
1. Press and hold the button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be disabled.
The transmitter and buttons can be used to lock and unlock the doors.
(if the option is installed), however once the button is pressed, the vehicle’s
starter disable device, (where installed) will be disengaged allowing the vehicle to start.
To stop the alarm, press the trunk button on the remote control.
If the button is not pressed, the alarm will automatically stop after 30 seconds
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk open / Turning
on the ignition key will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn,
parking lights, and dome light will turn on alerting of an intrusion for 30 seconds. Then it will stop and
automatic reset and re-arm. If the any one of the sensors or detectors is still active, the alarm system will
sound a maximum of 3 times of 30 seconds cycles.
NOISE ABATEMENT CIRCUIT:
Your system has a “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to
faulty door pin switches or environmental conditions such as thunder, jackhammers airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor
or switch has triggered the alarm; the “Noise Abatement Circuit” will interpret this pattern of triggers as a
false alarm. After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses, that sensor or
switch until a different sensor or switch is trigger.
“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open
door for three full cycles, the doors will be bypassed until the trigger ceases.
DISARMING WITHOUT A TRANSMITTER
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to the 'ON’ position.
2. (Alarm will sound.)
3. Within 10 seconds push and release the antenna mounted valet switch. The alarm will stop sounding
and enter the disarm mode. You can now start and operate the vehicle normally.
SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
Press & hold + button of LCD remote until 1 beep sounds, press button (see LCD Remote
manual Table 1) to activate system trigger check.
Note: If the system has no response then you are out of range.
SYSTEM’S STATUS CHECK (For two-way transceiver operation only)
Press & hold + button of LCD remote until 1 beep sounds, press button (see LCD Remote
manual Table 1) to activate system trigger check. Note: If it has no response then you are out of range.
DRIVER PAGING / LOST & FOUND (For two-way transceiver operation only)
This feature is useful the event that someone wants to page the driver of the parked vehicle or someone
cannot find his LCD remote transceiver.
Under the ignition switch “OFF” condition, press and hold the valet switch for 2 seconds to page the driver,
one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding and
“ ” indication flashes on Remote LCD transceiver.
DOME LIGHT CONVENIENCE SUPERVISION (Optional Feature)
The alarm has a unique feature that will turn on your vehicle dome light as follows:
1. Upon disarming, the interior light will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turning on the ignition switch or arming the alarm will turn off the dome light.
2
-
Way LCD Remote Manual:
Transmitter button LCD Display Feature & remark
Press & release button
+
Backlight turns on 3 seconds
Press & Hold button +
for 3 seconds (until 1
chirp)
U 01 LCD display show U 01 = enter Manual 1
of LCD Remote
Press button Press button = vehicle’s status check.
Press button Press button = system trigger check.
Press button
PRESS button FOR OPTION OF CAR
1 / CAR 2
Press & hold button for
2 sec.
on = Button Lock
Press & hold button for 2 sec. Button
Lock On
Press & hold button for
2 sec.
Melody Vibration Press & hold button for 2 sec. Vibrator
or Melody mode selection
Press & hold button for
2 sec.
Press & hold button for 2 sec. Fast
Count Down
Press & hold button for
2 sec. (2-way LCD remote
beep sound).
Press & hold button for 2 sec. LCD
remote Beep Sound mode Enable
Exit: Press +
++
+ buttons or not press any button within 15 seconds, it will exit remote
programming mode automatically.
Two beeps to confirm
Transmitter button LCD Display
System feature & remark
Press & hold button
+ for 3 seconds (until
2 chirps)
12 is flashing
Manual – 2 of LCD Remote ( chirp x 2), for clock time
adjust or button to decrease or increase “Hour” digit,
adjust hour from 0 to 12.
Complete adjust “Hour, “Press button.
00 is flashing
or button - Adjusts clock “Minute” from 0 to 59.
Press button complete clock setting.
Alarm Clock adjust
12 is flashing
or button to decrease or increase “Hour” digit, adjusts
clock hour from 0 to 12.
Complete adjust “Hour, “Press button.
00 is flashing
or button - Adjusts clock “Minute” from 0 to 59.
Press button complete Alarm clock setting.
Count Down Timer
setting
0 :00
0 is flashing
or adjust parking “Hour” (value from 0 to 2).
Complete adjust “Hour, “Press button.
or adjust parking “Minutes” (value from 0 to 30).
Press button complete count down timer setting.
Press & hold button
+ for 5 seconds (chirp
x 3)
Full battery
icons flash
Power Save mode : ON / OFF
LCD remote transceiver uses “0” current to save the battery
power.
Exit: Press
+
++
+
buttons or not press any button within 15 seconds, it will exit remote
programming mode automatically
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.