Advance Security TR61 Remote Control User Manual 140904 Final SL 62oper both sides Draft

Download:
Mirror Download [FCC.gov]
Document ID	2387601
Application ID	JgwuAMJTZtmAFC29nUUBwQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.66kB (233237 bits)
Date Submitted	2014-09-14 00:00:00
Date Available	2014-09-14 00:00:00
Creation Date	2014-09-11 13:24:37
Producing Software	GPL Ghostscript 8.54
Document Lastmod	2014-09-11 13:24:37
Document Title	140904-Final SL-62oper both sides-Draft-
Document Creator	PDFCreator Version 0.9.3
Document Author:	eva

Model IUV711A
ACTIVE LOCKING – LOCK & ARMING:
STANDARD LCD ICON CONFIGURATIONS:
TRANSMITTER OPERATION
Transmitter
Button
System Function
The lock icon will be displayed
when the door are locked.
Remark
Valet Mode
All the function shall be
temporarily on hold.
Lock Doors & Arm System
Panic function
Car Locator
Arm and Delete The 2 Stage
Shock Sensor
Arm System and Hidden
Alarm Function
Silent Arming / Disarming
II
Active Anti Car-Jacking Mode
Unlock Doors & Disarm
System
Two Steps Door Unlock &
Disarm System(optional)
Trunk Release (Channel 3)
Passive Arming By-pass
Activate or Turn Off The
Remote Start
Channel # 4 Timer Output (4)
Switch to 2nd car operation
Press and Hold for 3 seconds.
Press Trunk
button to stop
panic function
Press when in armed mode
Warn Away trigger
Trigger on Shock Sensor
Press twice within 3 seconds.
Pass will appear on the remote
Press within 3 seconds and Hold
Shock Sensor Trigger
Trigger on Shock Sensor
Hood Trigger
Hood is illegally opened
button for 2 seconds
Ignition in "off" position.
Ignition in "on" position press
and hold for 2 seconds
Trunk Trigger
Trunk is illegally opened
Door Trigger
Doors are illegally opened
Press twice within 3 seconds.
Press and Hold for 2 seconds
While the system Disarmed.
Press button once.
Press
Twice if set to start safety mode
Channel 4
For 1-way TX only, Press & hold
until TX LED on
Sensor Bypass
Sensor bypass under Arm
mode
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Pressing the
button on the transmitter twice within 3
seconds will arm the security system and by-pass the shock sensor. The system will chirp one additional time to
confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming cycle
PASSIVE LOCKING OR ARMING: Programmable
Active arming / disarming is controlling your security system via the remote transmitter. This security system is
equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the
last door is closed. Operation is as follows.
1.
2.
3.
Turn the ignition to the “OFF” position and exit the vehicle.
After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any
door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle
entrances are closed.
After 30-second timer has elapsed, the security system will automatically “ARM”. The siren or horn will
chirp [1] time and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING: Programmable
The vehicle doors will automatically lock after passive arming cycle has been completed.
Remote Transmission
You are transmitting the
signal to control unit
In – Range Indicator
You are within the range
of the remote control.
PASSIVE ARMING BY-PASS: While the system is disarmed, Press the
button twice, the system will
respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as
Activate Channel 3 (Trunk
Release).
Activate Channel 4
Time Monitor
Parking Meter
0 :00 Reminder when time is up
CH 5
Activate Channel 5
Low Battery
You have to replace
battery of remote control.
Alarm Clock
Power Save (battery icon
full bar flash)
Melody Mode
Remote Control alert
user through melody sound
Vibration Mode
Remote Control vibrates
when the system is
triggered
BATTERY REPLACEMENT:
Engine Cranking
Your vehicle engine
Cranking by remote
control
Timer Control Start
Engine start automatically
every 2 or 3 hours.
long as you wish. To exit passive by-pass, press the transmitter
normal status.
or
buttons and the system will return to
ACTIVE UN-LOCKING – UNLOCK & DISARM:
for parking
12:00
button together on the
SILENT LOCKING AND UNLOCKING: ARMING / DISARMING: Press the
transmitter to LOCK or UNLOCK your security system, No chirp sound will be heard; arm / disarm confirmation
will be through the vehicles parking lights only.
Button Lock (icon on)
System trigger
CH 4
1. Press
button on transmitter.
2. The siren or horn will chirp once and the parking lights will flash once indicating that the system is now
armed. The vehicle doors will lock upon arming when interfaced with the security system.
Note: Defective sensor reminder: If the siren or horn sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. (OPTIONAL)
Ignition Trigger (icon flash)
Ignition switch is illegally
turned on
2nd Car Operation
REMOTE CONTROL TRANSMITTER:
CR2032 x 2 PCS battery powers the Remote Transmitter. When the power of the
battery weakens a
icon shall be displayed on the LCD screen. When the old
batteries are replaced, there will be beep sounds indicate the power is up of the
transmitter.
The One-way remote is powered by two CR2016 Batteries.
The unlock icon will
be displayed when the
door are unlocked
Driver paging
Someone is paging
you from of your
vehicle
Engine Running
Your vehicle's engine
is running
Manual Gear Mode
programmed
1. Press the
button on the transmitter.
2. The siren or horn will chirp twice and parking lights will flash twice to indicate that the security system is now
disarmed. The vehicle doors will unlock when interfaced with the security system.
IGNITION CONTROL DOOR LOCKS.
If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the
vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned
“OFF”.
TRUNK RELEASE: Press and hold
release or other electric devices.
button on transmitter for three seconds to remote control the trunk
CAR LOCATOR: Press the
button on the transmitter when the vehicle is in the armed / locked mode to active
car locator function. The siren or horn will chirp 6 times. The parking light will flash 12 times, allowing you to
easily locate your car.
VALET MODE: (System is in Disarm Mode)
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions
and remote start functions are bypassed, however, the remote panic feature and remote door locks will remain
operational. To use the valet mode, the system must first be disarmed either by using your remote transmitter,
or by operating the Manual Override sequence.
Get into/out valet mode using the ignition key.
Enter Valet Mode:
a). Under disarm mode, turn the ignition to “ON\OFF\ON” position.
b). Press and hold valet switch for 3 seconds until the LED turns ON solid. The LED will remain on as long
as the system is in 'valet mode'.
Exit Valet Mode:
a). Turn ignition 'ON\OFF\ON'.
b). Push and hold valet switch for 3 seconds, The LED will turn off indicate the system are exiting the
valet mode.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the
alarm in case of emergency.
1. Press and hold the
button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be disabled.
The transmitter
and
2-Way LCD Remote Manual:
TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
buttons can be used to lock and unlock the doors.
(if the option is installed), however once the
button is pressed, the vehicle’s
starter disable device, (where installed) will be disengaged allowing the vehicle to start.
To stop the alarm, press the trunk
button on the remote control.
If the button is not pressed, the alarm will automatically stop after 30 seconds
Transmitter button
button once on the transmitter.
1. Press
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will turn on and the climate
controls will activate and adjust the vehicle’s interior temperature to your preset setting. (While the
vehicle is running, the “ ” icon and the “minutes” digit on the LCD screen will flash and the will indicate
countdown timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.)
5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit
shuts off the countdown timer will turn off and the transmitter will play a melody.)
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk open / Turning
on the ignition key will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren, horn,
parking lights, and dome light will turn on alerting of an intrusion for 30 seconds. Then it will stop and
automatic reset and re-arm. If the any one of the sensors or detectors is still active, the alarm system will
sound a maximum of 3 times of 30 seconds cycles.
NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions
exists:
1.
2.
3.
4.
5.
6.
7.
The hood is opened.
The brake pedal is pressed.
The gear selector is in any gear other than “PARK” or “NEUTRAL”
The system in valet mode.
Release the parking (hand) brake. (For Standard Transmission Gear Vehicle or Turbo Timer Mode)
The system is failed in engine start memorize set up (For Standard Transmission Gear Vehicle.)
If the vehicle failed to start, the above status will flash on the LCD screen
NOISE ABATEMENT CIRCUIT:
Your system has a “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to
faulty door pin switches or environmental conditions such as thunder, jackhammers airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor
or switch has triggered the alarm; the “Noise Abatement Circuit” will interpret this pattern of triggers as a
false alarm. After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses, that sensor or
switch until a different sensor or switch is trigger.
“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open
door for three full cycles, the doors will be bypassed until the trigger ceases.
SAFE START (Child safety mode)
DISARMING WITHOUT A TRANSMITTER
To operate the vehicle while the engine is running from the remote start,
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
of LCD Remote
Press
button
Press
button = vehicle’s status check.
Press
button
Press
button = system trigger check.
Press
button
PRESS
This feature allows the vehicle to remain running after the key has been removed from the ignition. This
feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but
would like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
button once on the transmitter and the LED indicator will
flash 3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
Press & hold
button for
Press & hold
on = Button Lock
2 sec.
Press & hold
button for
Melody
Press & hold
Lock On
Vibration
button for
button for
button for 2 sec. Fast
Press & hold
button for 2 sec. LCD
remote Beep Sound mode Enable
beep sound).
Exit: Press
buttons or not press any button within 15 seconds, it will exit remote
programming mode automatically.
Two beeps to confirm
Transmitter button
LCD Display
Press & hold button
for 3 seconds (until
System feature & remark
Manual – 2 of LCD Remote ( chirp x 2), for clock time
12 is flashing
2 chirps)
adjust
or
button to decrease or increase “Hour” digit,
adjust hour from 0 to 12.
Complete adjust “Hour, “Press
or
Alarm Clock adjust
button.
button - Adjusts clock “Minute” from 0 to 59.
Press
button complete clock setting.
or
button to decrease or increase “Hour” digit, adjusts
clock hour from 0 to 12.
Complete adjust “Hour, “Press
button.
12 is flashing
or
00 is flashing
SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the engine will not start or will shut
down immediately:
the vehicle in an enclosed space for any extended period. Carbon Dioxide is
dangerous to Humans, pets and animals within the enclosed spaces.
button for 2 sec. Vibrator
Count Down
1. Press
button once on the remote transmitter under the remote start mode.
2. Move the optional remote start enable toggle switch to OFF position. (If installed)
3. Press the brake pedal
The vehicle will shut down and turn off the parking light to indicate the engine has stopped.
4. Pull down the hand brake. (for Standard Transmission Gear Vehicle)
The vehicle will shut down and turn off the parking light to indicate engine stopped
IMPORTANT: Remote Start should be used only in open areas, Never start and run
Press & hold
Press & hold
00 is flashing
1. The hood is opened.
2. The brake pedal is pressed.
3. The parking (hand) brake is released (For Turbo Timer Mode)
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Press
button on the remote transmitter under remote start mode.
7. The system trigger.
8. The vehicle refused to start running after {3} unsuccessful attempts.
button for 2 sec. Button
or Melody mode selection
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
button FOR OPTION OF CAR
1 / CAR 2
2 sec. (2-way LCD remote
OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
LCD display show U 01 = enter Manual 1
U 01
chirp)
2 sec.
buttons twice within 3 seconds to start the vehicle. or
2. The user presses the transmitter
and
buttons at the same time to start the vehicle.
NOTE: Contact your installing dealer to activate this feature.
button (see LCD Remote
DOME LIGHT CONVENIENCE SUPERVISION (Optional Feature)
The alarm has a unique feature that will turn on your vehicle dome light as follows:
1. Upon disarming, the interior light will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turning on the ignition switch or arming the alarm will turn off the dome light.
for 3 seconds (until 1
1. The user presses the transmitter
SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
DRIVER PAGING / LOST & FOUND (For two-way transceiver operation only)
This feature is useful the event that someone wants to page the driver of the parked vehicle or someone
cannot find his LCD remote transceiver.
Under the ignition switch “OFF” condition, press and hold the valet switch for 2 seconds to page the driver,
one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding and
“
” indication flashes on Remote LCD transceiver.
Press & Hold button
2 sec.
TEMPORARY STOP FEATURE:
Press & hold
button of LCD remote until 1 beep sounds, press
button (see LCD Remote
manual Table 1) to activate system trigger check. Note: If it has no response then you are out of range.
Backlight turns on 3 seconds
Press & hold
1. Enter the vehicle and turn the ignition switch to the 'ON’ position.
2. (Alarm will sound.)
3. Within 10 seconds push and release the antenna mounted valet switch. The alarm will stop sounding
and enter the disarm mode. You can now start and operate the vehicle normally.
SYSTEM’S STATUS CHECK (For two-way transceiver operation only)
Feature & remark
Press & release button
Factory default is set to press the
button once on the transmitter to start the vehicle. You can program
this feature to eliminate an accidental remote start:
The Override function may be used if the remote transmitter is lost or inoperative.
button of LCD remote until 1 beep sounds, press
Press & hold
manual Table 1) to activate system trigger check.
Note: If the system has no response then you are out of range.
LCD Display
Count Down Timer
setting
0 :00
0 is flashing
button - Adjusts clock “Minute” from 0 to 59.
Press
button complete Alarm clock setting.
or
adjust parking “Hour” (value from 0 to 2).
Complete adjust “Hour, “Press
or
Press
Press & hold button
for 5 seconds (chirp
x 3)
Full battery
icons flash
button.
adjust parking “Minutes” (value from 0 to 30).
button complete count down timer setting.
Power Save mode : ON / OFF
LCD remote transceiver uses “0” current to save the battery
power.
Exit: Press
+ buttons or not press any button within 15 seconds, it will exit remote
programming mode automatically

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Producer                        : GPL Ghostscript 8.54
Create Date                     : 2014:09:11 13:24:37+08:00
Modify Date                     : 2014:09:11 13:24:37
Title                           : 140904-Final SL-62oper both sides-Draft-
Creator                         : PDFCreator Version 0.9.3
Author                          : eva
Subject                         : 

EXIF Metadata provided by EXIF.tools