Advanced RF Technologies EPOCH-HP-20 Epoch-HP-20, Epoch-HP-10, Epoch-HP-05 1900MHz band User Manual Epoch HP
Advanced RF Technologies, Inc. Epoch-HP-20, Epoch-HP-10, Epoch-HP-05 1900MHz band Epoch HP
Contents
- 1. instructions
- 2. manual
manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 794113 |
| Application ID | dnrNBx6e7zZFaiDeSa+B2g== |
| Document Description | manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 43.3kB (541280 bits) |
| Date Submitted | 2007-05-18 00:00:00 |
| Date Available | 2007-05-18 00:00:00 |
| Creation Date | 2007-05-08 11:31:41 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2007-05-08 11:31:41 |
| Document Title | Microsoft Word - Epoch-HP User Manual.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | jsanchez |
EPOCH-HP USER MANUAL Version 1.1 Epoch-HP RF Repeater User Manual V1.1 Version 1.1 (Modified May 4, 2007) Information in this document is subject to change without notice. Advanced RF Technologies, Inc. 1996-2007. All rights reserved. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro- vide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Please send comments to: E-Mail: info@adrftech.com Phone: (323) 254-8131 Fax: (323) 254-4928 Address: Advanced RF Technologies, Inc. Attention: Technical Publications Department 2607 Colorado Blvd., 1st floor Los Angeles, CA 90041 USA Advanced RF Technologies, Inc. Proprietary Document Page 2 of 36 Epoch-HP RF Repeater User Manual V1.1 TABLE OF CONTENTS 1. Introduction of Epoch-HP ...................................................................................5 1.1 Overview ......................................................................................................5 1.1.1 2. 1.1.2 Highlights ......................................................................................5 Available Models ............................................................................5 Installation Guide for Epoch-HP..........................................................................6 2.1 Environmental Requirements ........................................................................6 2.1.1 2.1.2 Antenna Separation/Isolation..........................................................6 Line of Sight ...................................................................................8 2.2 Warnings and Hazards ..................................................................................9 2.3 RF exposure warning ....................................................................................9 2.4 Tools and Recommendations for Installation...............................................11 2.5 Epoch-HP Parts List ....................................................................................11 2.6 Epoch-H V1.X Installation and Requirements ..............................................11 2.6.1 Minimum Requirements ..................................................................11 2.6.2 Epoch-H V1.X Installation ...............................................................12 2.6.3 Initial Startup of Epoch-H V1.X........................................................12 2.7 Pre-Installation using Epoch-H V1.X ...........................................................12 2.8 Step by Step Instructions for Installation .....................................................12 2.8.1 3. Repeater Setup .............................................................................12 User Manual V1.0 using Epoch-HP V1. X .......................................................17 3.1 Menu Structure ...........................................................................................17 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 Window Overview .........................................................................17 Status Window ..............................................................................18 Control Menu ...............................................................................19 3.1.3.1 3.1.3.2 General Setting Window..................................................19 Alarm Setting Window ....................................................22 Install Window ..............................................................................23 System Menu ................................................................................25 3.1.5.1 Information ....................................................................22 3.1.5.2 Firmware Upgrade ..........................................................22 3.2 Using the Epoch-H V1.X .............................................................................26 3.2.1 Changing Parameters ...................................................................26 3.3.1 General (Fixed Parameter) Alarms .................................................28 3.3 Alarms........................................................................................................27 3.3.2 Downlink/Uplink Alarms...............................................................28 3.4.1 Default General Setting.................................................................29 3.4 Default Control Settings..............................................................................29 4. 3.4.2 Default Alarm Setting ...................................................................29 Maintenance Guide for Epoch-HP..................................................................30 4.1 Periodic Inspection Checklist ......................................................................30 Advanced RF Technologies, Inc. Proprietary Document Page 3 of 36 Epoch-HP RF Repeater User Manual V1.1 4.2 Preventive Measures for Optimal Operation.................................................30 4.2.1 5. 6. 4.2.2 Recommendations ........................................................................30 Precautions ..................................................................................30 Troubleshooting ...........................................................................................31 5.1 Epoch-H V1.X Scenarios .............................................................................31 5.2 Common Installation Problems ...................................................................31 Warranty and Repair Policy............................................................................33 6.1 General Warranty ........................................................................................33 6.2 Limitations of Warranty...............................................................................33 Appendix A: Specifications ..........................................................................................35 A.1 Repeater Specifications (Epoch-HP-05).......................................................35 Advanced RF Technologies, Inc. Proprietary Document Page 4 of 36 Epoch-HP RF Repeater User Manual V1.1 1. Introduction of Epoch-HP 1.1 Overview Epoch-HP series repeaters enhances outdoor wireless coverage in the most effective and cost efficient way. For its intelligent design and versatility, EpochHP series repeaters are the ideal choice for wireless coverage problems outdoors. In many large scale in-building applications, Epoch-HP series repeaters can also be used (e.g. malls, campus, stadiums, etc.) with passive antennas instead of a DAS (distributed antenna system) and offer significant cost savings. 1.1.1 Highlights • 37, 40 or 43 dBm Composite Output Power • 95 dB gain • 30 dB AGC Range @ 0.5 dB Step • Can Set AGC Output Power Level • Band Selectable via Software • Can Support Non-Contiguous Bands • Supports Embedded Wireless Modem • Supports Network Management Monitoring System via SNMP 1.1.2 Available Models Epoch-HP is available in all 1900 MHz PCS band combinations. The following table illustrates the six models which are available in the Epoch-HP series: Product ID Description 5 W composite output power with 95 dB of gain (30 dB dynamic AGC range). Band Option 1 (S1): Any 5 or 15 MHz block or any 5 Epoch-HP-05-SX MHz and 15 MHz contiguous blocks at anytime. Band Option 2 (S2): Any 5 or 10 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. Band Option 3 (S3): Any 5 or 5 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. Epoch-HP-10-SX 10 W composite output power with 95 dB of gain Advanced RF Technologies, Inc. Proprietary Document Page 5 of 36 Epoch-HP RF Repeater User Manual V1.1 (30 dB dynamic AGC range). Band Option 1 (S1): Any 5 or 15 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. Band Option 2 (S2): Any 5 or 10 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. Band Option 3 (S3): Any 5 or 5 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. 20 W composite output power with 95 dB of gain (30 dB dynamic AGC range). Band Option 1 (S1): Any 5 or 15 MHz block or any 5 Epoch-HP-20-SX MHz and 15 MHz contiguous blocks at anytime. Band Option 2 (S2): Any 5 or 10 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. Band Option 3 (S3): Any 5 or 5 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. Table 1 – Epoch-HP Models ** Special band combinations are also supported in all the models. 2. Installation Guide for Epoch-HP 2.1 Environmental Requirements 2.1.1 Antenna Separation/Isolation Separation between antennas is necessary to prevent oscillation. Oscillation occurs when the signal entering the system continually reenters, due to the lack of separation between the donor and server antennas. In other words, the signal is being fed back into the system. This creates a constant amplification of the same signal. As a result, the noise level rises above the signal level. Advanced RF Technologies, Inc. Proprietary Document Page 6 of 36 Epoch-HP RF Repeater User Manual V1.1 Donor Server RF Repeater Figure 1 - RF Repeater Oscillation To prevent feedback, the donor and server antennas must be separated by an appropriate distance to provide sufficient isolation. Isolation is attained by separating antennas a sufficient distance so that the output of one antenna does not reach the input of the other. dependent on the gain of the repeater. This distance is A sufficient isolation value is 13 ~ 15 dB greater than the maximum gain of the repeater. For example, if the gain of the repeater is 50 dB, then an isolation of 63 ~ 65 dB or greater is required. In the same manner, because the Epoch-HP has a maximum gain of 95 dB, it requires an isolation of at least 108 ~ 110 dB. Advanced RF Technologies, Inc. Proprietary Document Page 7 of 36 Epoch-HP RF Repeater User Manual V1.1 2.1.2 Line of Sight The donor antenna which points towards the base station typically has a narrow beam antenna pattern. As a result, a slight deviation away from the direction of the BTS can lead to less than optimum results. In addition, obstacles between the repeater and the BTS may impair the repeater from obtaining any BTS signal. As a result, the repeater cannot transmit signal to the coverage area. Therefore, a direct line of sight to the BTS for the donor antenna is vital to the function of a repeater. For the same reason, placing the server antenna in direct line of sight of the coverage area is also necessary. BTS Donor Antenna Figure 2 - Direct Line of Sight to the BTS Advanced RF Technologies, Inc. Proprietary Document Page 8 of 36 Epoch-HP RF Repeater User Manual V1.1 2.2 Warnings and Hazards WARNING! ELECTRIC SHOCK Tampering with the modules within the Epoch-HP repeater exposes the user to electric shock and the risk of damaging the unit. DO NOT TAMPER with modules within the unit. Opening or tampering with any modules inside the Epoch-HP will void all warranties. WARNING! HIGH VOLTAGE In installing donor or server antennas, avoid close proximity to overhead power lines or high power components. Contact with high power components will severely damage the repeater and may cause serious injury and/or death to the user. Exercise extreme caution when installing antennas near high power lines. WARNING! EXPOSURE TO RF Working with the repeater while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure. Visit the FCC website at www.fcc.gov/oet/rfsafety to learn more about the effects of exposure to RF electromagnetic fields. WARNING! Operating the Epoch-HP with antennas in very close proximity facing each other could lead to severe damage to the repeater. Advanced RF Technologies, Inc. Proprietary Document Page 9 of 36 Epoch-HP RF Repeater User Manual V1.1 2.3 RF exposure warning Important Safety Information In order to satisfy the FCC RF exposure requirements, you must ensure that the installation complies with following: For INDOOR use, an omni-directional antenna with a maximum gain of 3 dBi can be used with this unit. Service antenna is connected to the Server port in the Epoch-HP via a cable with typical 1~10 dB loss in accordance with the length of the cable. Service antennas must be positioned to observe minimum separation of 50 cm (~20 inch) from all users and bystanders. For the protection of personnel working in the vicinity of service antennas, the following guidelines for minimum distances between the human body and the antenna must be observed. The installation of an service antenna must be such that, under normal conditions, all personnel cannot come within 50 cm(~20 inch) from any service antenna. Exceeding this minimum separation will ensure that the employee or bystander does not receive RF exposure beyond the maximum permissible exposure according to section 1.1310 (Limits for General Population/Uncontrolled Exposure) For OUTDOOR use, an directional antenna with a typical gain of 12 dBi can be used with this unit. Donor antenna is connected to the donor port in the Epoch-HP via a cable with typical 1~10 dB loss in accordance with the length of the cable. Donor antenna must be positioned to observe minimum separation of 152 cm (~ 5 ft) from all users and bystanders. For the protection of personnel working in the vicinity of service antennas, the following guidelines for minimum distances between the human body and the antenna must be observed. The installation of an donor antenna must be such that, under normal conditions, all personnel cannot come within 152 cm(~5 ft) from donor antenna. Exceeding this minimum separation will ensure that the employee or bystander does not receive RF exposure beyond the maximum permissible exposure according to section 1.1310 (Limits for General Population/Uncontrolled Exposure) Advanced RF Technologies, Inc. Proprietary Document Page 10 of 36 Epoch-HP RF Repeater User Manual V1.1 2.4 Tools and Recommendations for Installation The following may be necessary (not required) for installation of the repeater: a. Crescent Wrench b. Philips Screw Driver c. Lift, Ladder, or Boom Truck d. Spectrum Analyzer e. Sweep Tester f. Signal Generator g. Pilot Scanner h. RF Power Meter i. j. Voltmeter Coaxial Cables k. Compass l. PC with an USB port The list above may vary depending on if brackets are used to install the repeater. Bring additional tools that may be useful during installation. It is recommended that two people install the Epoch-HP repeater system. 2.5 Epoch-HP Parts List The Epoch-HP repeater system includes: a. Epoch-HP Repeater PART ID EPOCHHP01 QUANTITY b. Nuts and Bolts BLTS01 c. Epoch-H V1.X GUI HPOMS01 d. Ground Cable GNDSTD01 f. Keys KEYS01 e. USB Cable USB01 2.6 Epoch-H V1.X Installation and Requirements 2.5.1 Minimum Requirements Hardware (PC Platform) CPU: 200 MHz Memory: 32 MB USB Port: 1 Port Hard Disk: CD-ROM Drive 10 MB (Free Space) Compatible Operating System: Microsoft Windows XP (Preferred), 2000 Advanced RF Technologies, Inc. Proprietary Document Page 11 of 36 Epoch-HP RF Repeater User Manual V1.1 2.5.2 Epoch-H V1.X Installation Installing the Epoch-H V1.X a. Insert the CD into the CD-ROM drive. b. Click on “My Computer.” c. In the “My Computer” window, click on your CD-ROM drive (usually labeled D:). d. Double-click the file labeled “Epoch-H V1.x.exe.” e. The installation wizard will guide you through the conclusion of the Epoch-H V1.X installation process. 2.5.3 Initial Startup of Epoch-H V1.X a. Using the USB cable (USB01) that is provided, connect one end of the cable to the PC USB port and the other end to the repeater’s USB port located on the bottom of the repeater. b. Open the Epoch-H V1.X software 2.7 Pre-Installation using Epoch-H V1.X Prior to the Epoch-HP installation, ensure that: a. The USB driver is installed and the USB cable is connected at both ends. b. The donor and server antennas are in place. c. The TX and RX communication status LEDs are blinking. ** The TX and RX LEDs should blink every 1 second only in the Status Window. In the Status Window, a blinking green RX LED indicates that the PC is retrieving data from the repeater (Epoch-HP). Similarly, a blinking green TX LED indicates that the PC is transmitting data to the Epoch-HP. ** If neither of the LEDs is blinking: (1) check if the USB deriver has been installed; (2) check the USB cable is connected properly between the PC and the repeater; or (3) check if the repeater power is on. 2.8 Step by Step Instructions for Installation 2.8.1 Repeater Setup Advanced RF Technologies, Inc. Proprietary Document Page 12 of 36 Epoch-HP RF Repeater User Manual V1.1 1. Open the Epoch-HP Open the front door of the repeater cabinet by using the key (KEYS01) provided. There are two locks integrated into the door latches. One key works for both locks. ** Please keep the cabinet door open fully during the installation until you are instructed to close the cabinet. # 3 - Server # 2 - Donor Antenna Port Antenna Port # 4 – USB Port # 5 – Back-Up Battery Cable # 1 - AC Power Supply Opening Figure 3 – Bottom Side of the Repeater 2. Connect the Power Source and Ground Wire Make sure that the power switch inside the repeater is turned off before connecting the power cable. Connect the power cable to the power source as shown in Figure 3 (# 1). ** Before connecting the power cable to the power source, make sure that the voltage source is 110 V. 3. Connect the Donor Antenna Connect one end of the RF coaxial cable to the donor antenna and the other end to the repeater donor port located on the bottom of the EpochHP as shown in Figure 3 (# 2). 4. Connect the Server Antenna Connect one end of the RF coaxial cable to the server antenna and connect the other end to the repeater server port located on the bottom of the Epoch-HP as shown in Figure 3 (# 4). Advanced RF Technologies, Inc. Proprietary Document Page 13 of 36 Epoch-HP RF Repeater User Manual V1.1 5. Connect the USB Cable Using the USB cable (included in the box), connect one end of the cable to the Epoch-HP’s USB port located on the bottom of the repeater (# 4 Figure 3) and the other end to the laptop’s USB port. 6. Connect the Back-Up Battery (Optional) If a back-up battery is needed, please connect it to the power supply located inside the repeater. You can pass the back-up battery power cable through the opening as shown in Figure 3 (# 5). 7. Turn On the Power for Epoch-HP Make sure that the donor and server antennas and the power cable are securely connected to the correct ports. located inside the repeater. Turn the power switch on, 8. Launch the Epoch-H V1.X Program Open the Epoch-H V1.X program. You will see the Status Window. ** Please make sure that both communication status LEDs, the TX and the RX on the bottom of the window, are blinking periodically. A green blinking TX LED indicates that the data is being transmitted from the PC to the Epoch-HP. A green blinking RX LED indicates that the data is being retrieved from the Epoch-HP to the PC. ** For more detailed information on the Epoch-H V1.X, please refer to Section 3 on page 15. ** If either the TX or the RX status LED is not blinking, check if the USB driver has been installed. For more information, refer to Section 5, “Troubleshooting” on page 29. ** Before proceeding to the next step, please close the cabinet door (do not lock) at this time in order to avoid inadvertent RF feedback going inside the repeater.” 9. Go to the Install Window Now with the blinking TX and RX status LEDs on the Status Window, go to the Install Window. You will see the following: Advanced RF Technologies, Inc. Proprietary Document Page 14 of 36 Epoch-HP RF Repeater User Manual V1.1 Figure 4 - Installation Window of the Epoch-H V1.X 10. Select the Desired Band or Bands Select the desired band or bands by clicking on “Band Selection.” Once you do so, the following window will come up: Figure 5 – Band Selection Window of the Epoch-H V1.X You can select any 5 or 15 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. ** The above band configuration strictly depends on which model you are using (e.g. S1, S2, or S3). Please refer to Table 1 on Page 5. ** If a wireless modem is not connected, skip steps 11 through 13 and proceed to step 16. 11. Provide SNMP Information Type in the Site ID and the Manager IP address as given to you by the Wireless Provider. Once both the parameters are typed in, you must click “Set” for it to be executed. 12. Check the Modem Connection Advanced RF Technologies, Inc. Proprietary Document Page 15 of 36 Epoch-HP RF Repeater User Manual V1.1 Verify that the Auto Connection box is checked and then click on “Connect.” 13. Click on Install After the first three steps, click on “Install.” This installation process will normally take less than 5 minutes. ** Please refer to the “Quick Installation Guide” for any questions or problems that you may encounter during this installation process. If a modem is not connected to the repeater and you click the “Install” button, the following pop-up window will appear: Figure 6 – No Wireless Modem Connected If you choose to continue with the RF portion only, simply click “Yes” and the installation process will resume again. 14. Check the Front LED Panel Check that the Power LED is on (Green) and neither Soft Fail LED (Yellow) nor Hard Fail LED (Red) is lit. ** If the Soft Fail or Hard Fail LED is on, refer to Section 3.3 on page 25. ** You can go to the Status Window of the Epoch-H V1.X program to view the basic parameters of the repeater once the repeater has installed successfully. 17. Lock the Epoch-HP Door Now you can lock the door using the key provided. CONGRATULATIONS!! The Epoch-HP Installation Process is Complete. Advanced RF Technologies, Inc. Proprietary Document Page 16 of 36 Epoch-HP RF Repeater User Manual V1.1 User Manual V1.0 using Epoch-H V1.X 3.1 Menu Structure 3.1.1 Window Overview Status Control Install you to monitor the current you to change or adjust the through an automated installation The Status Window allows settings and status of the Epoch-HP. The Control Window enables Epoch-HP’s parameters and The Install Window guides you of the Epoch–HP repeater. settings. System Information For more detailed system information, click on the Info. Menu. Information such as model number, serial number, and firmware version of the repeater are included here. You can also upgrade the repeater firmware from this menu. Figure 7 - Status Window of the Epoch-H V1.X Advanced RF Technologies, Inc. Proprietary Document Page 17 of 36 Epoch-HP RF Repeater User Manual V1.1 3.1.2 Status Window The Status Window is the monitoring window of the Epoch-H V1.X. This window enables the user to monitor the status and settings of the Epoch- HP. In other words, no parameters can be changed in the Status Window. To change parameters, you will need to go to the Control Window. Repeater Input Indicates input signal strength of the repeater after being amplified by Band Message Board currently selected bands, center which are sent out recently. In addition, the user Will display filter bandwidth, The user will be able to see heartbeat messages downlink & uplink operating frequencies. will also be able to see any alarms that are the donor antenna generated along with messages once the alarms are cleared as well. [in dBm]. Modem Connection Will let you know if the Repeater Gain wireless modem is connected to the repeater Indicates the gain of the repeater [in dB]. Clear Repeater Output Will clear the Message Board. repeater [in dBm] Log File The output of the before being radiated by the server antenna. History for the Figure 8 - Status Window of the Epoch-H V1.X heartbeats and alarms generated from the repeater and can be saved as a text file. Alarm Button The alarm button changes color to the corresponding status of the repeater: Green for normal operation; Yellow for soft fail Installation Status Bar repeater is properly installed. Window Loaded Properly, etc.) and transmit (TX) & receive (RX) communication LEDs. Will let you know if the Displays the status of the repeater (e.g. Status alarm; and Red for hard fail alarm. Click on the alarm button for detailed information. Advanced RF Technologies, Inc. Proprietary Document Page 18 of 36 Epoch-HP RF Repeater User Manual V1.1 3.1.3 Control Menu 3.1.3.1 General Setting Window Figure 9 - General Setting Window of the Epoch-H V1.X AGC Mode AGC (Auto Gain Control) adjusts the variable gain of the repeater to ensure a constant specified output power of 37, 40 or 43 dBm (depending on the EpochHP model). The functionality of the AGC feature is assured under the condition that the input BTS signal is within the specified AGC range and that sufficient isolation exists between antennas. By default, the AGC ON box is checked. To manually change the gains in both the links, AGC ON must be unchecked. If AGC ON is checked and Uplink Tracking ON is unchecked, the user can specify the AGC level in the downlink and in the uplink respectively @ 0.5 dB step. By default, the AGC Level is set to maximum output power in each link. By default, Uplink Tracking is not checked. Once both AGC and Uplink Tacking are checked, this allows the user to set the AGC level in the downlink only. The default values that will be displayed on both Downlink and Uplink AGC Levels are the maximum output power as shown in the table below: Output Power Level Default Downlink AGC Level Default Uplink AGC Level 5W 43 dBm 33 dBm 10 W 40 dBm 30 dBm 20 W 37 dBm 27 dBm Table 2 – Default AGC Power Level Values Advanced RF Technologies, Inc. Proprietary Document Page 19 of 36 Epoch-HP RF Repeater User Manual V1.1 If Uplink Tracking ON is unchecked, then the user can set the AGC level in both links. Models Gain Range AGC Input Range Epoch-HP-05/XX 65 to 95 dB -58 to -28 dBm Epoch-HP-10/XX 65 to 95 dB -55 to -25 dBm Epoch-HP-20/XX 65 to 95 dB -52 to -22 dBm (37 dBm or 5 W Model) (40 dBm or 10 W Model) (43 dBm or 20 W Model) Table 3 – AGC Input Range Downlink/Uplink HPA Mode The HPA mode enables the user to turn the HPA on or off. If the HPA is turned off on either link, the Epoch-HP will not operate properly. Both HPAs needs to be turned on for the RF portion of the repeater to work in both directions (downlink and uplink). By default, the Downlink/Uplink HPA ON box is checked. Either or both HPAs can be turned off for troubleshooting purposes during an installation process. Uplink Tracking/Offset Modes Uplink tracking mode enables or disables the Uplink Tracking ON feature that sets the gain in the uplink equaling to the gain in the downlink. gain offset is the difference in the uplink and downlink gains. The tracking For example, if the downlink gain is 80 dB, the Uplink Tracking ON is checked, and the Uplink Tracking Gain Offset is set to 3 dB, the uplink gain would be 77 dB. By default, the Uplink Tracking ON box is not checked. If it was checked, then the default Uplink Tracking Offset is set to 3 dB. This means that the uplink gain will track the down link gain and will be 3 dB less. Control Item Action Setting Value Uplink Tracking ON Set Uplink Tracking Mode ON or OFF Uplink Tracking Offset Set Tracking Gain Offset 0 ~ 25 dB @ 0.5 dB step Table 4 - Uplink Tracking Mode and Tracking Gain Offset Range Advanced RF Technologies, Inc. Proprietary Document Page 20 of 36 Epoch-HP RF Repeater User Manual V1.1 Downlink/Uplink Gain The gain of the Epoch-HP is the ratio of the input signal to the output signal. The gain may be set in both links. ** The manual gain option is disabled when the AGC ON box is checked. Reboot By clicking the “Reboot” button, similar to how the operation works in a PC, the control board of the repeater will restart itself. Factory Setting Clicking on the “Factory Setting” button resets the settings of the repeater to the original default factory settings as noted in the “Default Control Settings” in Section 3.4 on page 27. ** You will lose your current saved settings once you click on “System Factory Setting” Advanced RF Technologies, Inc. Proprietary Document Page 21 of 36 Epoch-HP RF Repeater User Manual V1.1 3.1.3.2 Alarm Setting Window Figure 10 - Alarm Setting Window of the Epoch-H V1.X Control Item Downlink/Uplink RSSI Downlink/Uplink Input Overload Action Downlink Uplink Sets Low RSSI Alarm Level -120 ~ -30 dBm -120 ~ -30 dBm Sets Input Overload Level -90 ~ -20 dBm -90 ~ -20 dBm Table 4 - Alarm Threshold Values RSSI The RSSI alarm is the minimum RSSI value that the Epoch-HP requires to ensure optimal coverage. The RSSI alarm will go off when the RSSI is lower than the threshold value (refer to the RSSI value in the Alarm Setting Window). Input Overload A Downlink/Uplink Input Overload alarm occurs when the input signal strength to the Epoch-HP exceeds the threshold value (refer to the Uplink/Downlink Input Overload values in the Alarm Setting window). Advanced RF Technologies, Inc. Proprietary Document Page 22 of 36 Epoch-HP RF Repeater User Manual V1.1 Heartbeat Heartbeat is a periodic message sent out to Wireless Provider’s NOC only if the repeater has a wireless modem connected to it. Control Item Action Setting Value Heartbeat ON/OFF Set Heartbeat Mode ON/OFF Periodic Time Set Heartbeat Time 1 ~ 60 min @ 1 min step Table 6 - Heartbeat Mode and Time Range Heartbeat Mode The Heartbeat ON box is checked by default. The heartbeat feature is only available if the repeater has a wireless modem connected to it. Periodic Time The Periodic Time is the time interval between Heartbeats only if the repeater has a wireless modem connected to it. The default periodic time is 20 minutes. The periodic time can be adjusted manually between 1 to 60 minutes. 3.1.4 Install Window At the time of installation, the installer needs to go to the Install Window of the Epoch-H V1.X. The Install Window will guide the installer through a step by step process to properly install the Epoch-HP repeater. For setup or installation of a repeater, go to the Install Window. Figure 11 - Install Window of the Epoch-H V1.X Advanced RF Technologies, Inc. Proprietary Document Page 23 of 36 Epoch-HP RF Repeater User Manual V1.1 Band Select the desired band or bands by clicking on “Band Selection.” Once you do so, the following window will come up: Figure 12 – Band Selection Window of the Epoch-H V1.X You can select any 5 or 15 MHz block or any 5 MHz and 15 MHz contiguous blocks at anytime. ** If a wireless modem is not connected to the repeater, simply select the desired operating band(s) and click on “Install.” SNMP (only applicable if a wireless modem is connected to the repeater) a. Site ID The Site ID is a unique ID for each site and will be provided by the Wireless Provider. b. Manager IP The Manager IP address will be provided by the Wireless Provider. The repeater will send alarms to the Wireless Provider’s NOC to the assigned Manager IP address. Modem (only applicable if a wireless modem is connected to the repeater) The Auto Connection box needs to be checked when the wireless modem is installed inside the repeater. A wireless modem is used in order to send the alarms and the heartbeat over the air to the Wireless Provider’s NOC. Repeater Click the “Install” button and the repeater will setup automatically. For information regarding the use of the Epoch-H V1.X during installation, refer to Section 2.7.1 on page 12, “Repeater Installation” (starting at number 8). Advanced RF Technologies, Inc. Proprietary Document Page 24 of 36 Epoch-HP RF Repeater User Manual V1.1 3.1.5 System Menu 3.1.5.1 Information The Info. Window displays the following: (1) Model Number; (2) Serial Number; and (3) Firmware Version of the Epoch-HP repeater. Contact information is included along with a link to Advanced RF Technologies, Inc.’s URL. Figure13 - Info. Window of the Epoch-H V1.X Advanced RF Technologies, Inc. Proprietary Document Page 25 of 36 Epoch-HP RF Repeater User Manual V1.1 3.1.5.2 Firmware Upgrade The Firmware Upgrade Window enables you to upgrade the firmware of the repeater. The latest version of the firmware will be provided to you by ADRF. Save the latest version of the firmware on your PC. Click on Open and locate the firmware from your PC. Click on Download and automatically the latest version of the firmware will be downloaded onto the repeater. Figure 14 – Firmware Upgrade Window of the Epoch-H V1.X 3.2 Using the Epoch-H V1.X 3.2.1 Changing Parameters In changing the parameters of the repeater via use of the Epoch-H V1.X, note that the values entered into the Epoch-H V1.X are limited to the ranges and modes specified in the Menu Structure section as explained in Section 3.1 on page 15. The Organizational Chart below shows (alphabetically) the parameters that can be changed and the location of each parameter in the Menu Structure. The asterisk “*” denotes parameters that apply to both uplink and downlink. Advanced RF Technologies, Inc. Proprietary Document Page 26 of 36 Epoch-HP RF Repeater User Manual V1.1 Control Menu General Setting Alarm Setting Reboot Periodic Time Factory Setting Manual Gain Control* RSSI* Input Overload* AGC Level Control* Uplink Tracking Offset Figure 15 - Variable Parameters in the Epoch-H V1.X 3.3 Alarms All the various alarms that are supported by Epoch-HP can be viewed by clicking the “Alarm” button on the Status Window. If a soft fail alarm should occur, the alarm of concern would be highlighted in yellow. In the same manner, the corresponding hard fail alarm would be highlighted in red. In order to find out what is causing the alarm(s), simply place the mouse cursor over the highlighted yellow or red alarm box (Note: only applicable to some of the alarms) and a tool tip message will appear, displaying the threshold value and the current measured value. window, click the “Refresh” button. To update the Figure 16 - All Alarm Parameters Supported by Epoch-H V1.X Advanced RF Technologies, Inc. Proprietary Document Page 27 of 36 Epoch-HP RF Repeater User Manual V1.1 In the event of a hard fail alarm, the control board will shutdown the HPA (both uplink & downlink) for 30 seconds and then turns on the HPA to check for a repeated hard fail occurrence. If the next two occurrences sense a hard fail, the control board will shutdown the HPA for 20 minutes (total of three consecutive hard fails). After 20 minutes, the HPA will automatically come back alive and the control board will check if the Hard Fail alarm has cleared. If it has not, the same process will continue as mentioned above. 3.3.1 General (Fixed Parameter) Alarms Alarm List Soft Fail Hard Fail Comments Over/Under Current Over Temperature Synthesizer Lock Band selection will not work properly VSWR > 1.5:1 Low Isolation/OSC. Repeater will be in an oscillating state RF Power Soft Fail: Less than 0.5 A @ under current Hard Fail: More than 7.5 A @ over current Soft Fail: 158 ~ 185 °F Hard Fail: > 185 °F Will occur in the event of any Hard Fail alarm Table 7 - General (Fixed Parameter) Alarms of the Epoch-H V1.X 3.3.2 Downlink (Forward) Uplink (Reverse) Downlink/Uplink Alarms Alarm List Soft Fail Hard Fail Remark RSSI Alarms will turn on if the Input Power Overload limits specified in the Over Power* RSSI Input Power Overload Over Power* value is not within operable Control Alarm Setting Window. Note: The Over Power parameter is fixed and cannot be modified by the user. Table 8 – List of Alarm Settings of the Epoch-H V1.X Advanced RF Technologies, Inc. Proprietary Document Page 28 of 36 Epoch-HP RF Repeater User Manual V1.1 The example below distinguishes the difference between an over power soft failure and an over power hard failure: The threshold value for the downlink over power parameter is set to 45.0 dBm (factory set value for the 20 W model), a Hard Fail alarm would occur if the downlink over power value was greater than 45.0 dBm (43 dBm is the maximum composite power allowable). Similarly, a Soft Fail alarm would occur if the downlink over power value was greater than 44.0 dBm but less than 45.0 dBm. Vice versa, the same example is also applicable in the uplink side. 3.4 Default Control Settings 3.4.1 Default General Setting Control Item Setting Value AGC Mode ON Downlink/Uplink HPA Mode ON Uplink Tracking Mode ON Downlink/Uplink Gain 80 dB DL: 37/40/43 dBm Downlink/Uplink AGC Level UL: 27/30/33 dBm (depending on model) Tracking Gain Offset 3 dB Table 9 - Adjustable Alarm Settings of the Epoch-H V1.X When Uplink Tracking ON mode is enabled by default, the Tracking Gain Offset is set to 3 dB. b. When AGC ON mode is enabled, by default, the Downlink/Uplink AGC Level is set to 37/40/43 dBm (depending on model). a. 3.4.2 Default Alarm Setting Setting Value Control Item Downlink Uplink RSSI -95 dBm -110 dBm Input Overload -30 dBm -30 dBm Heartbeat On/Off ON Heartbeat Time 20 minutes Table 10 - Default Alarm Parameter Values of the Epoch-H V1.X Advanced RF Technologies, Inc. Proprietary Document Page 29 of 36 Epoch-HP RF Repeater User Manual V1.1 Maintenance Guide for Epoch-HP 4.1 Periodic Inspection Checklist a. Ensure that the door is closed and locked before inspection. b. Check for loose connections to the repeater and antennas. If connections are loose, make sure that all connections are tightly fastened properly. c. Cables and connectors are in good condition. d. Open the repeater door to check that the repeater is turned on. e. Check that all components inside are intact with no unusual wear (e.g., rust, dirt, etc.). f. Ensure that the repeater brackets (if used) are in good condition and that the repeater is securely fastened. 4.2 Preventive Measures for Optimal Operation 4.2.1 Recommendations • Perform the Periodic Inspection Checklist quarterly or semiannually. • Always lock the door to the repeater to prevent unauthorized access. 4.2.2 • Precautions Do not operate the repeater with the antennas in extremely close proximity as this may cause damage to the repeater. • Do not shut down the repeater unless absolutely necessary (in the case where the repeater is a hazard to safety). • Do not change parameters unless instructed to do so by an authorized supervisor. • Do not move the repeater unless instructed to do so by an authorized supervisor. • Do not detach any cables to the repeater unless repair of respective components are necessary. Advanced RF Technologies, Inc. Proprietary Document Page 30 of 36 Epoch-HP RF Repeater User Manual V1.1 Troubleshooting 5.1 Epoch-H V1.X Scenarios Tx Rx Explanation The USB port can not send or receive data. Check the USB port RED RED connection to the computer and the repeater. Ensure that the repeater is turned on and that the connection to the repeater is secure. Blinking GREEN The repeater is not receiving any commands from the RED Blinking Solid GREEN GREEN software. Ensure that the repeater is tuned on and check for proper USB port connection. The repeater is not receiving any commands from the software. In this state, the repeater is either processing or executing a command. Wait for a few seconds for the Rx LED to blink periodically. Blinking GREEN Blinking GREEN Successful Connection. The Epoch-H V1.X and the repeater are communicating successfully. Table 9 - Tx and Rx LEDs Note: The Tx/Rx LEDs will blink periodically only on the Status Window. 5.2 Common Installation Problems Problem The power green LED on the second Possible Solution Check if the power supply switch is turned on by opening the second door of the repeater. panel is not lit. Software & Laptop - No Communication Please verify if the USB driver has been installed. Option 1: Status Window – Weak Signal or Check that the donor and server antennas are connected to the proper antenna ports on the repeater. Donor RSS Option 2: Reposition or rotate the donor antenna around until Low Isolation or Increase the separation between the donor and server Downlink/Uplink Check the cabling because RF signals maybe leaking and also Downlink/Uplink Option 1: Add an attenuator after the donor/server antenna to Input Power reduce the strong donor/server signal coming into the Oscillation VSWR Alarm Overload Alarm a stronger signal is received. antennas by moving the antennas around or by rotating them. verify that the connectors are tightly secured. repeater. Advanced RF Technologies, Inc. Proprietary Document Page 31 of 36 Epoch-HP RF Repeater User Manual V1.1 Option 2: An oscillation in the system could cause this alarm. Check if there is sufficient separation between the donor and the server antennas. Option 1: Add an attenuator after the donor/server antenna to Downlink/Uplink Over Power Alarm reduce the strong donor/server signal coming into the repeater. Option 2: An oscillation in the system could cause this alarm. Check if there is sufficient separation between the donor and the server antennas. Table 11 – Troubleshooting Tips Advanced RF Technologies, Inc. Proprietary Document Page 32 of 36 Epoch-HP RF Repeater User Manual V1.1 Warranty and Repair Policy 6.1 General Warranty The Epoch-HP carries a Standard Warranty period of two (2) years unless indicated otherwise on the package or in the acknowledgment of the purchase order. 6.2 Limitations of Warranty Your exclusive remedy for any defective product is limited to the repair or replacement of the defective product. Advanced RF Technologies, Inc. may elect which remedy or combination of remedies to provide in its sole discretion. Advanced RF Technologies, Inc. shall have a reasonable time after determining that a defective product exists to repair or replace a defective product. Advanced RF Technologies, Inc. warranty applies to repaired or replaced products for the balance of the applicable period of the original warranty or ninety days from the date of shipment of a repaired or replaced product, whichever is longer. 5.3 Limitation of Damages Advanced RF Technologies, Inc. entire liability for any defective product shall in no event exceed the purchase price for the defective product. 5.4 No Consequential Damages Advanced RF Technologies, Inc. has no liability for general, consequential, incidental or special damages. 5.5 Additional Limitation on Warranty Advanced RF Technologies, Inc. standard warranty does not cover products which have been received improperly packaged, altered, or physically damaged. For example, broken warranty seal, labels exhibiting tampering, physically abused enclosure, broken pins on connectors, any modifications made without Advanced RF Technologies, Inc. authorization, will void all warranty. 5.6 Return Material Authorization (RMA) No product may be returned directly to Advanced RF Technologies, Inc. without first getting an approval from Advanced RF Technologies, Inc. If it is determined that the product may be defective, you will be given an RMA number and instructions in how to return the product. An unauthorized return, i.e., one for which an RMA Advanced RF Technologies, Inc. Proprietary Document Page 33 of 36 Epoch-HP RF Repeater User Manual V1.1 number has not been issued, will be returned to you at your expense. Authorized returns are to be shipped prepaid and insured to the address on the RMA in an approved shipping container. You will be given our courier information. It is suggested that the original box and packaging materials should be kept if an occasion arises where a defective product needs to be shipped back to Advanced RF Technologies, Inc. To request an RMA, please call (323) 254-8131 or send an email to techsupport@adrftech.com. Advanced RF Technologies, Inc. Proprietary Document Page 34 of 36 Epoch-HP RF Repeater User Manual V1.1 Appendix A: Specifications A.1 Repeater Specifications ELECTRICAL SPECIFICATIONS PARAMETERS Frequency Range SPECIFICATIONS DL 1930 to 1990 MHz UL 1850 to 1910 MHz Sub Band Filtering 5 MHz, 15 MHz or 20 MHz Operating Frequency Programmable Frequency Error ≤ +/- 0.05 ppm System Delay ≤ 5 usec Repeater Gain 65 to 95 dB Maximum DL / UL Output Power 20 W +43 dBm / +33 dBm 10 W +40 dBm / +30 dBm 5W +37 dBm / +27 dBm DL AGC Range 30 dB UL AGC Range 30 dB AGC Step Size 0.5 dB Gain Linearity ≤ +/- 0.8 dB Gain Flatness Spectral Mask Emission COMMENTS Any 5MHz @ 60MHz Any 15MHz @ 60MHz Any 5+ 15MHz @ 60MHz Each Band Composite ≤ 3.0 dB Peak to Peak @ Each Band ≤ 4.0 dB Peak to Peak @ Full Band ≤ -45 dBc @ Fc +/- 885 KHz ≤ -55 dBc @ Fc +/- 1.98 MHz < -13 dBm @ Fc +/- 2.25 MHz Rho Factor ≥ 0.96 Noise Figure Maximum 5 dB VSWR ≤ 1.5:1 Advanced RF Technologies, Inc. Proprietary Document @ Maximum Gain Page 35 of 36 Epoch-HP RF Repeater User Manual V1.1 MECHANICAL SPECIFICATIONS PARAMETERS SPECIFICATIONS Cabinet Size 18.11 x 20.08 x 9.55 inches Cabinet Weight 73 lbs Cabinet Mount Type Utility Pole Mount Antenna N-Type (F) Coupling SMA (F) Frame Ground Lug Terminal (5.5SQ) Control USB Connector Type Cooling Forced Air Cooling Weatherproofing NEMA 4, IP65 COMMENTS WxHxD (Including Bracket) Including Bracket 30 dB 2 FAN POWER SPECIFICATIONS PARAMETERS SPECIFICATIONS COMMENTS Main AC Power 100 or 240 V AC Select Switch Type AC Frequency 50 to 65 Hz Power Consumption 20 W 500 Watts 10 W 360 Watts 5W 250 Watts AC Supply Protection Fuse Grounding External Threaded Stud ENVIRONMENTAL SPECIFICATIONS PARAMETERS SPECIFICATIONS Operating Temperature -22 ˚F to +122 ˚F Storage Temperature -40 ˚F to +176 ˚F Humidity 5 to 95%, RH Advanced RF Technologies, Inc. Proprietary Document COMMENTS Page 36 of 36
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 36 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:28db04bb-b3f5-42ea-a3ce-84c6145184cf Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2007:05:08 11:31:41-07:00 Create Date : 2007:05:08 11:31:41-07:00 Document ID : uuid:abeb5d61-d279-413a-947f-d8d90b58981b Format : application/pdf Title : Microsoft Word - Epoch-HP User Manual.doc Creator : jsanchez Author : jsanchezEXIF Metadata provided by EXIF.tools