Advantech Co TREK-510 COMPUTER User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1727173
Application ID	YqF3vqE4LiuC+MhkvI8xzw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	231.75kB (2896877 bits)
Date Submitted	2012-06-20 00:00:00
Date Available	2012-06-20 00:00:00
Creation Date	2011-10-12 23:31:58
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2011-10-12 23:34:40
Document Title	untitled

User Manual
TREK‐510 User manual
TREK‐510
In‐Vehicle Computing Box
Smart Display
User manual
Copyright
The documentation and the software included with this product are copyrighted 2010 by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time without notice. No part
of this manual may be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of Advantech Co., Ltd. Information provided in
this manual is intended to be accurate and reliable. How‐ ever, Advantech Co., Ltd. assumes no
responsibility for its use, nor for any infringements of the rights of third parties, which may
result from its use.
Acknowledgements
Intel and Atom are trademarks of Intel Corporation. Microsoft Windows and MS‐DOS are
registered trademarks of Microsoft Corp. All other product names or trademarks are
properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by persons
other than repair personnel authorized by Advantech, or which have been subject to misuse,
abuse, accident or improper installation. Advantech assumes no liability under the terms of
this warranty as a consequence of such events.
Because of Advantech’s high quality‐control standards and rigorous testing, most of our
customers never need to use our repair service. If an Advantech product is defective, it will be
repaired or replaced at no charge during the warranty period. For out‐ of‐warranty repairs,
you will be billed according to the cost of replacement materials, service time and freight.
Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU speed,
Advantech products used, other hardware and software used, etc.) Note anything
abnormal and list any onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any
helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully‐completed Repair and Replacement Order
Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable
container. A product returned without proof of the purchase date is not eligible for
warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to your
dealer.
TREK‐510 User manual
Part No. 2010051001
Edition 1
Printed in Taiwan
Jan 2011
Declaration of Conformity
This product has passed the CE test for environmental specifications. Test conditions for
passing included the equipment being operated within an industrial enclosure. In order to
protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage,
we strongly recommend the use of CE‐compliant industrial enclosure products.
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
z Consult the dealer or an experienced radio/TV technician for help.
Technical Support and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/support for the latest
information about the product.
Contact the distributor, sales representative, or Advantech's customer service center
for technical support if you need additional assistance. Please have the following
information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software, etc.)
– A complete description of the problem
– The exact wording of any error messages
TREK‐510 User manual
Warnings, Cautions and Notes
Warning!
Warnings indicate conditions, which if not observed, can cause personal
Caution!
Cautions are included to help you avoid damaging hardware or losing data.
e.g.
Note!
Notes provide optional additional information.
Document Feedback
To assist us in making improvements to this manual, we would welcome comments and
constructive criticism. Send all such in writing to: support@advantech.com
Packing List
Before setting up, check that the items listed below are included, in good condition. If any item
does not accord with the table, please contact your dealer immediately.
z TREK‐510 series In‐Vehicle Computing Box
z USB/Audio Cable clip
z Warranty card
Power cord: DC power inlet cable (180 cm ‐ for TREK‐510 only)
“Drivers, Utilities and User Manual" CD‐ROM
z End User License Agreement (WinCE model), please download driver and related
document from www.advantech.com/support
Ordering information
P/N
Description
TREK‐510‐GCEA0E
ST2062 333Mhz , GPS, GPRS module built in, WinCE5.0
7" vehicle display system, 480x234 resolution, with 4 wire resistive touch
screen, 2‐watts speaker.
2‐meter cable(paired with TREK‐510)
TREK‐303R‐LA0E
1700018342
Packing list
Item
Power cable
x1 Screw
x4
GPS antenna
x1 Cable clip for MIC in, line out, USB host, USB client
x4
WWAN antenna
x1 Start up manual CD
x1
TREK‐510 User manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this user manual for later reference.
3. Disconnect this equipment from AC outlet before cleaning. Do not use liquid or spray detergents
for cleaning.
4. For pluggable equipment, the power outlet shall be installed near the equipment and shall be
easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could
cause damage.
7. Do not leave this equipment in an environment unconditioned where the storage temperature
under ‐30°C (‐22°F) or above 70°C (158°F), it may damage the equipment.
Operating temperature: 50°C. Safety Certificate Temperature: 50°C
8. The openings on the enclosure are for air convection hence protects the equipment from
overheating. DO NOT COVER THE OPENINGS.
9. Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
10. Place the power cord such a way that people can not step on it. Do not place anything over the
power cord. The voltage and current rating of the cord should be greater than the voltage and
current rating marked on the product.
11. All cautions and warnings on the equipment should be noted.
12. If the equipment is not used for long time, disconnect it from the power source to avoid being
damaged by transient over‐voltage.
13. Never pour any liquid into ventilation openings. This could cause fire or electrical shock.
14. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
15. If any of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well or you cannot get it to work according to user manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
16. CAUTION: The computer is provided with a battery‐powered real‐time clock circuit. There is a
danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type
recommended by the manufacture. Discard used batteries according to the manufacturer’s
instructions.
17. THE COMPUTER IS PROVIDED WITH CD DRIVES COMPLY WITH APPROPRIATE SAFETY STANDARDS
INCLUDING IEC 60825.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
TREK‐510 User manual
18. This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
19. CAUTION: Always completely disconnect the power cord from your chassis whenever you work
with the hardware. Do not make connections while the power is on. Sensitive electronic
components can be damaged by sudden power surges.
20. CAUTION: Always ground yourself to remove any static charge before touching the motherboard,
backplane, or add‐on cards. Modern electronic devices are very sensitive to static electric
charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic
components on a static‐dissipative surface or in a static‐shielded bag when they are not in the
chassis.
21. CAUTION: Any unverified component could cause unexpected damage. To ensure the correct
installation, please always use the components (ex. screws) provided with the accessory box.
22. Caution text concerning lithium batteries:
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri af samme
23 "Rack Mount Instructions ‐ The following or similar rack‐mount instructions are included with the
installation instructions:
A) Elevated Operating Ambient ‐ If installed in a closed or multi‐unit rack
assembly, the operating
ambient temperature of the rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an environment compatible with the
maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow ‐ Installation of the equipment in a rack should be such that the amount of air
flow required for safe operation of the equipment is not compromised.
C) Mechanical Loading ‐ Mounting of the equipment in the rack should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading ‐ Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on over current protection
and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
E) Reliable Earthing ‐ Reliable earthing of rack‐mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the branch
circuit (e.g. use of power strips)."
24. CAUTION:
1. This product is connected to a fuse box in the passenger compartment before it connected to
the vehicle battery, and the fuse in a fuse box is UL listed and automotive fuse.
2. Use the appropriate flexible and SAE wiring to connect to a fuse box.
*This product is installed in the passenger compartment.
3. This product must be installed and maintained by qualified service personnel.
4. This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
TREK‐510 User manual
Wichtige Sicherheishinweise
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Bitte lesen sie Sich diese Hinweise sorgfältig durch.
Heben Sie diese Anleitung für den späteren Gebrauch auf.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine
Flüssig‐oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
Das Gerät ist vor Feuchtigkeit zu schützen.
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Verletzungen hervorrufen.
Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit‐ zung
schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es sollte auch
nichts auf der Leitung abgestellt werden.
Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät
gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus‐ lösen.
Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von
einer qualifizierten Servicestelle zu überprüfen:
Netzkabel oder Netzstecker sind beschädigt.
Flüssigkeit ist in das Gerät eingedrungen.
Das Gerät war Feuchtigkeit ausgesetzt.
Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz nur durch
densellben order einem vom Hersteller empfohlene‐mahnlichen Typ. Entsorgung
gebrauchter Batterien navh Angaben des Herstellers.
ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht fach‐ männische
Weise gewechselt wird. Verfangen Sie die Batterie nur gleicher oder entsprechender
Type, wie vom Hersteller empfohlen. Entsorgen Sie Batterien nach Anweisung des
TREK‐510 User manual
Herstellers.
23. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt
70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC‐704‐1
erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in
diesem Zusammenhang getätigten Aussagen ab.
Safety Precaution ‐ Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
z To avoid electrical shock, always disconnect the power from your PC chassis before
you work on it. Don't touch any components on the CPU card or other cards while the
PC is on.
z Disconnect power before making any configuration changes. The sudden rush of power
as you connect a jumper or install a card may damage sensitive electronic components.
Warning!
1.
2.
3.
4.
Input voltage rated: 6‐36 Vdc.
Transport: carry the unit with both hands and handle with care.
Maintenance: to properly maintain and clean the surfaces, use only
approved products or clean with a dry applicator.
CompactFlash: Turn off the power before inserting or removing
CompactFlash storage cards.
European Contact information:
Advantech Europe GmbH Kolberger
Straße 7
D‐40599 Düsseldorf, Germany
Tel: 49‐211‐97477350
Fax: 49‐211‐97477300
TREK‐510 User manual
Contents
Chapter
1.1
1.2
1.3
Chapter
2.1
2.2
2.3
2.4
2.5
2.6
Chapter
3.1
3.2
3.3
3.4
TREK‐510 User manual
General Information ............................12
Introduction ............................................................................................... 12
General Specifications ............................................................................... 13
Dimensions ................................................................................................ 14
Figure 1.1 TREK‐510 dimensions............................................ 14
System Setup .......................................15
A Quick Tour of the Vehicle Mounted ............................................................ 16
Figure 2.1 Front view of the TREK‐510 ....................................... 16
Figure 2.2 Rear side of the TREK‐510 .......................................... 16
Figure 2.3 Side view of the TREK‐510 .......................................... 16
Figure 2.4 B o tto m view of the TREK‐510 ...................................17
Figure 2.5 To p view of the TREK‐510 .......................................... 17
Installation Procedures.................................................................................... 17
2.2.1 Connecting the Power Cord .............................................................. 17
Table 2.2.1: Pin Definition of Power Cord ................................... 17
2.2.2 Power connector ………………….. ...........................................................18
Figure 2.6 Po we r c o n n e c to r o u t l o o k ................................... 18
Table 2.2.2: Pin Definition of Power connector.......................... 18
Figure 2.7 Po we r c o n n e c to r p h o to ...................................... 19
Running the BIOS Setup Program ...............................................................……..19
Installing System Software ............................................................................... 19
Installing the Drivers..................................................................................... 19
Programming Function Keys and GPIO/CAN BUS ....................................... 19
Hardware & Peripheral Installation ……20
Overview of Hardware Installation & Upgrading ..................................... 21
Installing the Storage Device and Memory ............................................. 21
Installing Optional Accessories .................................................................. 21
3.3.1 Installing TREK‐510 peripheral modules....................................... 21
Figure 3.1 Install peripheral in the system............................... …21
3.3.2 Installing the MiniPCI type WWAN, SIM card & coin battery ...... 22
Figure 3.2 MiniPCI type WWAN, SIM card & coin battery from bottom
view………………………………………………………….... ………………………………22
3.3.4 Installing CF card…………….......................................................... 22
Figure 3.4 Installing CF card….. ................................................. 23
Figure 3.5 Installing cable lock….. ............................................. 23
3.3.5 GPS module is unable to be installed by customer ....................... 23
Paired with TREK‐303 specification …...................................................... 23
TREK‐510 User manual
10
Chapter
4.1
4.2
Jumper Settings and Connectors ..... 24
Setting Jumpers and Switches................................................................ ….25
4.1.1 Locations of the Jumpers and connector.................................. ….26
Figure 4.1 Locations of jumpers and connectors on top side the
motherboard………………………………………………………………………….…26
Figure 4.2 Locations of jumpers and connectors on bottom side of the
motherboard……………………………………………………...……………………26
Figure 4.3 Locations of jumpers and connectors on bottom side of the
daughter board……………………………………………………27
4.1.2
Jumpers………………………………………………………………27
Table 4.1.2.1: Jumpers on motherboard................................... …27
Table 4.1.2.2: Jumpers on daughter board................................ ..27
4.1.3
Connectors.................................................................................... 28
Table 4.1.3.1: Connectors on motherboard................................. 28
Table 4.1.3.2: Connectors on daughter board.............................. 28
Jumper Settings……………………………………………………………….29
4.2.1
CMOS Clear for External RTC (JP2)………………………………29
Table 4.2.1: Clear CMOS / External RTC (JP1)…………………..29
4.2.2
Power Input Voltage Setting (JP1)…………………………………29
4.2.3
4.2.4
4.2.5
4.3
Chapter
Table 4.2.2: Power Input Voltage Selection (JP1) ………………..29
Pin 9 of COM3 Function Selection (JP3)…………………………29
Table 4.2.3: Pin 9 of COM 3 Function Selection (JP3)……………29
Pin 9 of COM8 Function Selection (J3)……………………………29
Table 4.2.4: Pin 9 of COM8 Function Selection (J3)……………..29
DI/GPS Function Selection (SW2) ………………………………..30
Table 4.2.5: Pin 9 o22f COM8 Function Selection (J3)…………30
COM Port Interface………………………………………………………………30
Table 4.7: Serial Port Function…………………………………….30
Table 4.7: Serial Port Settings…………………………………….30
Pin Assignments ...............................31
5.1
Front Side connectors…………………………………………………………..32
5.2
Rear Side Connectors………………………………………………………….32
5.3
Power Connector (12/ 24V; 6 ~ 36V)…………………………………………..32
Table 5.3: Power connector………………………………………..32
5.4
Smart Display Connector…………………………………………………………33
Table 5.4: Smart display connector………………………………..33
5.5
RS‐232 Connector (COM3, COM8)……………………………………………..34
Table 5.5: RS232/485/J1708 connector……………………………34
5.6
RS‐232 (COM9) / RS‐485 (COM5) / J1708 (COM6) Connector………34
Table 5.6: RS232/485/J1708 connector……………………….…..34
5.7
DI / DO Connector…………………………………………………………………35
Table 5.7: DI/DO connector………………………………………….35
5.8
CAN/Video in Connector…………………… ……………………………………35
Table 5.8: CAN/Video in connector………………………………...35
5.9
LED Connector…………………… ………………………………………………36
Table 5.9: LED connector…………………………………………….36
Chapter
6.1
TREK‐510 User manual
SW functionality ...............37
Introduction…………………………………………………………………………38
11
6.1.1
Execute J1939 demo utility……………………………………………………………………….….38
Figure 6. 1 IMC demo utility……………………………………………..………38
Figure 6.2 J1939 truck simulator………………………………38
Figure 6.3 J1939 test ………………………………………………………….…39
Figure 6.4 J1939 test ……………………………………………………..……39
CAN Test…………………………………………………………………………..…………………………39
Figure 6. 9 CAN test ‐2 ………………………………………………………………39
RTC test………………………………………………………………….……………………………………40
Figure 6.10 RTC test ‐1………………………………………………………………40
Figure 6.11 RTC test ‐2…………………………………………………..……………40
Figure 6. 12 RTC test‐3………………………………………………………………40
Figure 6. 13 RTC test‐4…………………………………………………….…………40
Figure 6.14 RTC test‐5…………………………………………………………….…41
Power Management ………………………………………………………………………………….…..41
6.3.1
Power management Mechanism………………………………….……………..42
6.3.2
Power Management utility program…………………………………………….43
6.3.3
Power Management Parameter settings………………………..…………….43
Figure 6.15 Power management test utility…………………………………43
6.3.4
TREK‐510 power consumption……………………………………………………….43
6.4
GPIO Test…………………………………………………………………………………….…44
Figure 6.16 DI/O test …………………………………………………………………….44
Figure 6.17 Digital in……………………………………………………………………..…44
Figure 6.18 Digital out……………………………………………………………………45
6.7
G‐ sensor …………………………………………………. ………………………………………..46
6.1.2
6.2
6.3
Chapter
6.1
6.1.1
6.1.2
6.2
6.3
TREK‐510 User manual
SW demo utility set Up...............37
Introduction…………………………………………………………………………38
Execute J1939 demo utility……………………………………………………………………….….38
Figure 6. 1 IMC demo utility……………………………………………..………38
Figure 6.2 J1939 truck simulator………………………………38
Figure 6.3 J1939 test ………………………………………………………….…39
Figure 6.4 J1939 test ……………………………………………………..……39
CAN Test…………………………………………………………………………..…………………………39
Figure 6. 9 CAN test ‐2 ………………………………………………………………39
RTC test………………………………………………………………….……………………………………40
Figure 6.10 RTC test ‐1………………………………………………………………40
Figure 6.11 RTC test ‐2…………………………………………………..……………40
Figure 6. 12 RTC test‐3………………………………………………………………40
Figure 6. 13 RTC test‐4…………………………………………………….…………40
Figure 6.14 RTC test‐5…………………………………………………………….…41
Power Management ………………………………………………………………………………….…..41
6.3.1
Power management Mechanism………………………………….……………..42
6.3.2
Power Management utility program…………………………………………….43
6.3.3
Power Management Parameter settings………………………..…………….43
Figure 6.15 Power management test utility…………………………………43
6.3.4
TREK‐510 power consumption……………………………………………………….43
6.4
GPIO Test…………………………………………………………………………………….…44
Figure 6.16 DI/O test …………………………………………………………………….44
Figure 6.17 Digital in……………………………………………………………………..…44
Figure 6.18 Digital out……………………………………………………………………45
6.7
G‐ sensor …………………………………………………. ………………………………………..46
12
Appendix A
A.1
A.2
Appendix B
A.1
TREK‐510 User manual
Paired with TREK‐303 ............................47
Table A.1: TREK‐303 spec .............................................................................. 48
Table A.2 Smart Display connector pin out.................................................... 49
Figure A.1 Hotkey utility………………………………………………………….…..51
WinCE5.0 compatible list ......................47
Table A.1: WinCE 5.0 compatible list............................................................. 48
13
Chapter
General Information
This chapter gives background
information on the TREK‐510
In‐Vehicle Computing Box.
Sections include:
z Introduction
z General Specifications
z Dimensions
TREK‐510 User manual
14
1.1
Introduction
The TREK‐510The TREK‐510 is a dedicated box computer for industrial vehicle fleets, transport trucks,
buses and taxis. TREK‐510 combined with a variety of I/O connectors can be connected to devices like
OBD‐II or TPMS (Tire Pressure Monitoring System). Built‐in wireless communications‐WWAN enables
TREK‐510 to send important driver/vehicle/location/car information back to the control center.
TREK‐510 can also operate in extreme environments with features like a wide working temperature
range (‐30 to 70 degrees) and anti‐shock/vibration design. TREK‐510 also uses a special design to
handle the critical issue of in‐vehicle power. Special power protection (ISO7637‐2/SAE J1455 Class A/
SAE J1113) and car power management software (Ignition on/off, delay on/off, low battery monitor)
prevent electrical noise and surges from impacting the system, guarding against damage from
transient car power.
I/O Connectors
1.2
General Specifications
Key features
ST ARM based STA2062 333 MHz CPU with Win CE 5.0
Automotive grade working temperature range (‐30° C to 70° C)
Rich I/O including CAN, multi‐COMs, isolation 4DI/4DO, Line out, Mic in, USB and SD.
Built‐in RF communication modules, including GSM/GPRS/HSDPA/CDMA
GPS with AGPS
Certifications: CE/FCC/e‐mark, MIL‐SD810F, ISO 7637‐2, SAE J1455, SAE J1113 regulations
Ignition on/off delay; SW controllable for car power management
Built in G sensor for active security system
ƒ
Specifications
–
–
–
–
Dimensions: (W x H x D): 261 x 125 x 59.1 mm
Weight: 1.5 kg.
Vehicle power feature:
Input voltage: 6 ~ 36Vdc, support ignition cold crank
Support Ignition on/off
Support low battery shut‐down protection threshold (optional)
Support power off event delay
TREK‐510 User manual
12
–
–
–
–
Note!
Support power on delay
Support power low delay
Support power low hard delay
Support hard off delay
For more detail of function please refer to Chapter 7, Section 6.3 of this manual.
Enclosure: Ruggedized aluminum without ventilation holes.
CPU: STA2062 333 MHz
System memory: 2 GB on board flash for bootloader, image & Customer's AP
Storage: SD: 1 x (external accessible)
Serial ports:
„ COM 1&2: 2 x Full Function RS‐232, 5 V/12 V @ 0.5 A, ping9, by jumper selected
„ COM3: 1 x 4‐wire RS‐232/485 (control by SW, 5 V/12 V @ 0.5 A, ping9, by jumper
selected
USB Host port: Supports up to two USB1.1 x by Type A. One from smart display port.
USB Client port: 1 x by mini Type AB
Watchdog timer: Supports 0‐255 secs time intervals, SW programmable and SW
enable/disabled.
RTC Battery: 3.0 V @ 200 mAH lithium battery.
Power management: Supports power saving modes including Normal mode.
Digital I/O: 4 x Isolated dry contact digital inputs from DB9 connector (2500 Vrms
protection), 4 x relay driver from DB9 connector
CAN bus: Support CAN V2.0B up to 500 kb/s.
Audio: 2 audio codecs, one is for smart display, one is for TREK‐510 line out and mic in
phone jack.
Optional modules:
‹ GPS
z LEA‐5S: 50 channels GPS
‹ RF:
z Quad‐band GSM/GPRS, HSDPA, CDMA
Operating temperature: ‐30 ~ 70° C
Relative humidity: 10 ~ 95% @ 40° C (non‐condensing)
Shock: 30 G peak acceleration (11 msec duration)
Certifications: CE, FCC, CCC, Emark
Vibration: 5 ~ 500 Hz SAE J1455 4.9.4.2, MIL‐STD‐810F 514.5
TREK‐510 User manual
13
1.3
Dimensions
Figure 1.1 TREK‐510 dimensions
TREK‐510 User manual
14
Chapter
ShThis
This chapter details system setup
Sections include:
z A Quick Tour of the computer box
z Installation Procedures
z Running the Setup Program
TREK‐510 User manual
15
2.1
A Quick Tour of the TREK‐510 Computing box.
Before starting to set up the In‐Vehicle Computing Box, take a moment to become familiar with the
locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures
below. When the Computer boxis placed inside truck glove cabinet or under the passenger’s seat next to
the driver, its front appears as shown in Figure 2.1.
Figure 2.1. Front view of TREK‐510
Figure 2.2. Rear view of TREK‐510
Unit: mm
TREK‐510 User manual
16
Figure 2.3. Side view of TREK‐510
Unit: mm
Figure 2.4. Bottom view of TREK‐510
Unit: mm
Figure 2.5. Top view of TREK‐510
TREK‐510 User manual
17
2.2
Installation Procedures
2.2.1 Connecting the Power Cord
Connect the three pin waterproof power cord to the DC inlet of the In‐Vehicle Computing
Box. On the open‐wire end, one pin is reserved for positive voltage and is marked, "+";
one pin is reserved for ground and is marked, "‐"; and, one pin is reserved for the
ignition signal with an “ignition” mark.
Note!
Ignition on/off setting: The TREK‐510 supports an ignition on/off
function so that you can power on/off the TREK‐510 via the ignition
signal/voltage and connect the TREK‐510 vehicle ignition switch.
Table 2.2.1 Pin Definition of Power Cord
Pin
Definition
‐
Ignition
Color
Red
Black
Orange
2.2.2 Power Connector
Figure 2.6. Power connector outlook
Table 2.2.2 Pin definition of PowerConnector(Molex Manufacturer part no.0430451200)
Pin
Signal
Pin
Signal
Chassis Ground
Ground
Ground
(Reserved)
(Reserved)
(Reserved)
Power Input (6~36 VDC)
Power Input (6~36 VDC)
Acc Ignition Input
10
Ground
11
(Reserved)
12
Power button Input
Connector : Molex 430451200
Mating connector: Molex 0430251200
TREK‐510 User manual
18
Figure 2.7. Power connector photo
Note!
Fuse holder: The fuse holder on the power cable is water/dust proof; you may change the fuse
(5 Amp) easily by yourself.
TREK‐510 User manual
19
Chapter
Jumper Settings and
Connectors
This chapter explains how to set up the
In‐Vehicle Computing Box hardware,
including instructions on setting
jumpers and connecting peripherals,
and how to set switches and read
indicators.
Be sure to read all the safety pre‐
cautions before beginning the
installation procedure.
Sections include:
Jumpers Setting
TREK‐510 User manual
23
4.1
Setting Jumpers and Switches
It is possible to configure the In‐Vehicle Computing Box to match the needs of the application
by resetting the jumpers. A jumper is the simplest kind of electrical switch. It consists of two
metal pins and a small metal clip, often protected by a plastic cover that slides over the pins
to connect them. To “close” a jumper, connect the pins with the clip. To “open” a jumper,
remove the clip. Sometimes a jumper has three pins, labeled 1, 2, and 3. In this case,
connect either pins 1 and 2, or pins 2 and 3.
open
closed
closed 2‐3
open
closed
closed 2‐3
A pair of needle‐nose pliers may be helpful when working with jumpers. If there are any
doubts about the best hardware configuration for the application, contact the local
distributor or sales representative before making any changes.
An arrow is used on the motherboard to indicate the first pin of each jumper.
TREK‐510 User manual
24
4.1.1 Locations of the Jumpers and Connector
Figure 4.1 Locations of jumpers and connectors on top side the motherboard.
4.1.2 Jumpers
Table 4.1.2.1: Jumpers on motherboard
Location
Function
CN3
Vehicle input voltage selection
CN14
Pin9 of COM6 RS232 RI or 5V or 12V select jumper connector
CN15
Pin9 of COM7 RS232 RI or 5V or 12V select jumper connector
TREK‐510 User manual
25
4.1.3
Connectors
. The table below lists the function of each connector.
Table 4.1.3.1: Connectors on motherboard
Location
Function
CN1
Power input connector
CN2
Vehicle Grounding connector
SW1
Reset connector
SW2,SW3
System setting switch
CN4
USB Client connector
CN5
SD Card connector
CN6
USB HOST TYPE‐A connector
CN7
USB HOST TYPE‐A cable connector (reserve)
CN8
Audio and Speaker Jack connector
CN9
VGA connector
CN10
RS232 connector (debug only and reserve)
CN11
JTAG connector (debug only and reserve)
CN12
CAN BUS termination connector
CN13
Full function 8‐wire RS232 connector
CN19
Isolated DI/DO and CAN bus connector
CN20
on board GPS antenna connector
CN21
RF Module board cable connector
CN22
UBLOX GPS module board cable connector
CN23
RTC battery connector
J1
uP RS232 connector (debug only and reserve)
J2
up burning image connector
TREK‐510 User manual
26
4.2
Jumper Settings
4.2.1 Power Input Voltage Setting (CN3)
TREK‐510 must be configured properly according the vehicle power input range.
Table 4.2.1: Power Input Voltage Selection (CN3)
12V Input (Default)
24V Input
4.2.2 Pin 9 of COM6 Function Selection (CN14)
Pin 9 on COM3 port can be configured as RI, 5V or 12V output.
Table 4.2.2: Pin 9 of COM3 Function Selection (CN14)
RI
+5VDC (max. 500mA)
+12VDC (max. 250mA)
4.2.4 Pin 9 of COM7 Function Selection (CN15)
Pin 9 on COM8 port can be configured as RI, 5V or 12V output.
Table 4.2.4: Pin 9 of COM8 Function Selection (J3)
RI
TREK‐510 User manual
+5VDC (max. 500mA)
+12VDC (max. 250mA)
27
4.3
COM Port Interface
The computer provides totally eight serial ports for difference uses. Six RS232 and 3 UART .
Ports, respectively. Below table describe each COM port function.
Table 4.3.1: Serial Port Function
Port
Function
COM0
2‐wire RS‐232 (TXD/RXD) for TREK‐303
COM1
4‐wire RS‐232 for System internal debug
COM2
4‐wire UART for UBLOX GPS module
COM3
4‐wire UART for system internal GPS
COM4
2‐wire RS‐232 (TXD/RXD) for internal uP
COM5
8‐wire UART for RF module
COM6
8‐wire Full functional RS‐232
COM7
8‐wire Full functional RS‐232
COM8
4‐wire RS‐232 and 2‐wire RS‐485 with software select
TREK‐510 User manual
28
Chapter
Pin Assignments
This chapter explains pin
assignments on the TREK‐510.
Sections include:
z Front/side Connector
z Power connector
z Smart display connector
z RS232 Connectors
z DI/DO connectors
TREK‐510 User manual
29
5.1 Front Side Connectors
5.2 Rear Side Connectors
5.3 Power Connector (12/ 24V; 6 ~ 36V)
Molex Manufacturer part no. 0430451200
Table5.3:PowerConnector
Pin
Signal
Pin
Signal
Chassis Ground
Ground
Ground
(Reserved)
(Reserved)
(Reserved)
Power Input (6~36 VDC)
Power Input (6~36 VDC)
Acc Ignition Input
10
Ground
11
(Reserved)
12
Power Button Input
TREK‐510 User manual
30
5.4
Smart Display Connector
Table5.4:SmartDisplayConnector
Pin
Signal
Pin
Signal
Backlight Enable output #
Panel Power Enable output #
LVDS Ground
Reset Button Input #
LVDS Clock +
LVDS Clock ‐
Ground
Ground
LVDS Data2 +
10
LVDS Data2 ‐
11
RS232 TXD1 #
12
RS232 RXD1 #
13
LVDS Data1 +
14
LVDS Data1 ‐
15
Ground
16
Ground
17
LVDS Data0 +
18
LVDS Data0 ‐
19
USB D‐
20
USB D+
21
Ground
22
Ground
23
+12VDC output (+/‐ 5%, max 1A)
24
+12VDC output (+/‐ 5%, max 1A)
25
+12VDC output (+/‐ 5%, max 1A)
26
+12VDC output (+/‐ 5%, max 1A)
27
Power Ground
28
Power Ground
29
Power Ground
30
Power Ground
31
NC
32
NC
33
NC
34
Power Button Input #
35
Ground
36
Mono. Line‐out
TREK‐510 User manual
31
5.5
RS‐232 (COM6, COM7) Connector
Table5.5:RS‐232 Connector
Pin
Signal
Pin
Signal
RS‐232 DCD
RS‐232 RXD
RS‐232 TXD
RS‐232 DTR
RS‐232 Ground
RS‐232 DSR
RS‐232 RTS
RS‐232 RI / +5V(max. 500mA) /
+V12 (max. 250mA)
RS‐232 CTS
5.6
RS‐232 (COM8) / RS‐485 (COM8) Connector
Table5.6:RS‐232/ RS‐485 Connector
Pin
Signal
Pin
Signal
RS‐485 D‐
RS‐232 RXD#
RS‐232 TXD
RS‐485 D+
Ground
Ground
RS‐232 RTS
RS‐232 CTS
NC
TREK‐510 User manual
32
5.7
DI / DO Connector
Table:5.7:DI/DO Connector
Pin
Signal
Pin
Isolated Dry Contact Input 1
Isolated Dry Contact Input 3
/Speed signal input for DR*
Isolation Ground
Isolated Dry Contact Input 2
Isolated Dry Contact Input 4
/Forward signal input for DR*
Isolated Relay Driver Output 1
Isolated Relay Driver Output 2
Isolated Relay Driver Output 3
Isolated Relay Driver Output 4
Signal
*Note. Regarding the setting of Pin3/4, please refer paragraph 4.2.5 (DI/GPS Function Selection).
5.8
CAN BUS Connector
Table:5.8:CANBUSConnector
Pin
Signal
Pin
Signal
CAN_H
CAN_L
Isolation Ground
Isolation Ground
Isolation Ground
NC
NC
NC
Isolation Ground
TREK‐510 User manual
33
5.9 LED indicator
Status
indicator
This USER Defined indicator GREEN LED is used for customization
This LED is controlled by software.
System Power
indicator
This system power indicator is a RED LED, controlled by Hardware.
When system is in normal mode, this LED will be lit on.
In other modes, this LED will be lit off.
WWAN Activity
indicator
This GPS Activity indicator is a BLUE LED, controlled by WWAN module
When WWAN is activity, this LED will be lit on.
GPS Activity
indicator
This GPS Activity indicator is a BLUE LED, controlled by GPS Chip
When GPS is activity, this LED will be lit on.
Status
Power
GPRS
GPS
TREK‐510 User manual
34
Chapter
Software functionality
This chapter includes the Windows
5.0 operating system on TREK‐510
platform.
Sections include:
z Introduction
z Windows CE startup Procedure
z Upgrade Procedure
z Utilities
z Network
z Application Program Development
z Windows CE5.0 Require
components.
TREK‐510 User manual
35
6.1
Introduction
The TREK510 platform is one embedded system with Windows® Embedded CE 5.0. The
Windows® Embedded CE 5.0 is a compact OS that occupies less storage space or system
resources compared with other operating systems such as Windows® XP. By its modular
nature, it is possible to choose those functions that are useful for specific application. Not
only reducing the system resources required, but also reduces start‐up time. In the field of
embedded applications, this is an appealing feature because the impact of downtime would
be minimized.
Furthermore, the small storage space it needs makes OS on solid-state disk possible, which implies higher robustness to harsh environments.
Figure 6.1 Windows® Embedded CE 5.0 on the TREK510 platform
6.2
Windows CE Startup Procedure
Windows CE image can be loaded by two methods, first way is by SD / MMC storage card, and
second way is by system on‐board chip. Storage card is higher boot priority than on‐board
system flash chip. In BOOTLOADER criteria, it will first read the Windows CE image from
external storage card. After download image done, booloader will burn image to on‐board
flash chip automatically. If external storage card is unavailable or no Windows CE image inside,
BOOTLOADER will load the Windows CE image from on‐board system flash chip. BOOTLOADER
copy Windows CE image to DRAM and launch WinCE from DRAM, whenever loaded by
external storage card or system on‐board flash chip.
TREK‐510 User manual
36
6.3
Upgrade Procedure
Advantech release two images for TREK510 platform. EBOOT.NB0 is bootloader and NK.BIN is
WinCE5.0 image.
You can upgrade image by following two ways :
a) Upgrade image via bootloader.
6.3.1 Upgrade image via bootloader
Bootloader image will be able to support image download then burn it to on‐board flash
chip automatically. You just copy EBOOT.NB0 or NK.BIN image to storage card separately then
reboot platform. Platform will automatically load image from storage card next boot time.
1) Bootloader image download
Step 1, Copy EBOOT.NB0 file to SD / MMC storage card.
Step 2, Power on platform.
Step 3, It will automatically read EBOOT.NB0 from storage card and then burn it to on‐board
boot ROM.
2) NK image download
Step 1, Copy NK.BIN file to CF / SD / MMC storage card. You needs to make sure EBOOT.NB0
doesn’t exist in storage card in advance.
Step 2, Power on platform.
Step 3, It will automatically read NK.BIN from storage card and then burn it to on‐board flash
chip.
6.4
Utilities
There are several useful utilities added in the standard Windows® Embedded CE 5.0 :
6.4.1 Test Utility
The utility “AdvDiag.exe” is one integrated test tool, which includes the function validation for
peripheral. You can use this tool to verify whether the peripheral function work or not. You
just copy this utility to storage card and then launch from WinCE by double click it.
Main Function :
Item
COMx (LOOPBACK)
COMx <=> COMy
TOUCH SCREEN
Audio Play
Audio Record
USB Keyboard
USB Mouse
WATCHDOG Timer
Backlight Test
TREK‐510 User manual
Function Description
Lookback test for COM1 ~ COM3
Two COM ports RS232 transmission
Touch Screen function validation
Audio play function validation
Audio record function validation
USB Keyboard function validation
USB Mouse function validation
Watchdog timer validation
Backlight function validation
37
DIO Control
PAUSE
REPEAT TEST
Etc ……
DIO function validation
Pause test process
Repeat test process
6.4.2 Test Procedure
You should see a lot of test items in left zone after launch this utility. You can insert enough
test items you want to right zone by pressing “Add” button. The test items in right zone will
be executed. Also, you can remove test items from right zone by pressing “Remove” button.
After you add test items done, you can go function test by pressing “EXE ALL” button. To press
“View Rpt” button, you will see the test result.
Figure 6.4 Test Utility
6.4.3 Startup execution
The TREK510 platform has a useful function call "Startup execution". After the system boot up,
the startup execution function would automatically perform. This function is useful for control
system to do the initialization processes or some other procedures. In TREK510 platform,
there are two ways to perform "Starup" function.
Method 1:
Step1: Create "startup" directory in SD/MMC storage card, USB disk.
TREK‐510 User manual
38
Step2: Copy executable files to "startup" directory that is created by Step 1.
Example:
We copy two executable files "softreset.exe" and "Notepad.exe" in "Startup", and then
reboot the system. After the system boot up, the two executable file would automatically
execute.
Method 2:
Step1: Create "startup" directory in SD/MMC storage card, USB disk(Hard Disk).
Step2: Create a file called "startup.ini" in "startup" directory. Type in the commands you want
to execute after boot up in that file.
Example:
Create "Startup.ini" in "\DiskOnChip\Startup" directory and reboot the system. The content of
startup.ini was listed below:
\windows\tty.exe
\windows\registry.exe
After the system reboot, "\windows\ tty.exe" and "\windows\ registry.exe" would
automatically execute. Be sure that the two methods are independent. It means they can be
used simultaneously.
6.4.4 Platform Setting
Platform Setting utility is an outstanding utility designed by Advantech Windows® CE software
team. It is an integrated environment where user can get useful system information as well as
configure favorite system settings and apply system control function on demand. Double click
the icon of Platform Setting on the desktop. Platform Setting is also put on Control Panel.
Following sections illustrate the functions of Platform Setting.
6.4.4.1 General
It shows the memory information including DRAM and on board MMC. Platform name and
version control are also put here.
TREK‐510 User manual
39
Figure 6.5 General information
6.4.4.2 Touch‐screen
The Touch‐screen page provides the calibration function. Click the "calibration" button, the
"Stylus Properties" windows would appear. Then click "calibrate" button in the Stylus
Properties window to enter calibration process. In the calibration process, user taps on the
center of the target on the screen then the target will move to the next position. After
calibration, press "OK" to leave Stylus Properties window, and then it will save calibration
setting to registry persistently.
Figure 6.6 Touch Calibration
TREK‐510 User manual
40
6.4.4.3 WatchDog timer
It is important in industrial applications that the control systems are rarely crashed, or are
capable of self‐reset if they are halted somehow. Watchdog function of automatic resetting
system is therefore provided in TREK510. There is a timer inside the watchdog function. User’s
AP could invoke the associated APIs in Watchdog function to start the timer, then Watchdog
function would repeat the countdown of the specified period of time to reboot the system if
the user’s AP does not clear the timer in time periodically. The Watchdog function in the
TREK510 provides eight different time intervals: 2 seconds, 5 seconds, 10 seconds, 30 seconds,
60 seconds, 2 minutes, 5 minutes and 10 minutes. The “Enable" button is used to start the
Watchdog function. Press the "SoftReset" button will cause system warm boot, reloads all
drivers and refresh the newest registry settings. Press the “REBOOT” button will cause the
system cold boot. Press RTC TIME start button, it will get real RTC value from RTC chip.
Figure 6.7Watchdog timer
6.4.4.4 Miscellaneous
The Misc page provides several functions as described below. The "Registry" block provides
registry save and registry clean function. Pressing “Save” button, the registry settings will be
saved to persistent storage as DISKONCHIP. Pressing “Clean” button, the registry setting will
return to default settings. The “A.Sync” button invokes ActiveSync to the host computer.The
Memory Management block will check if memory size needs to be allocated automatically
during boot. Once this is checked, program memory will be allocated half size of memory, and
storage memory will occupy the rest.
TREK‐510 User manual
41
Figure 6.8 Miscellaneous settings
6.5
Network
TREK510 build in one 3G controller. It appears at “Control Panel/Network and Dial‐up
Connections” via “DM9CE1”. User can configure its 3G support as follows:
1. Click "Start/Settings/Control Panel"
2. Double click "Network and Dial‐up Connections"
3. If the TREK510 is a node of the LAN with 3G servers, it is now available.
4. Support Module have MC55i/MC5728V/MV8790V
Figure 6.10 3G via Ethernet
TREK‐510 User manual
42
6.6
Application Program Development
The TREK510 is bundled with built‐in Windows® Embedded CE 5.0 operating system. In real
applications users need to execute various application programs on it. However, unlike its
other family, the Windows® Embedded CE 5.0 is a hardware‐dependent operating system.
That is to say, Windows® Embedded CE 5.0 application programs are only portable in the
source code level. Users must rebuild the runtime file for a different Windows® Embedded CE
5.0 platform even though the source code may not be changed at all.
6.6.1 PC System requirements
• Intel® Pentium‐90 CPU or more advanced
• Microsoft® Windows® 2000 Professional or Windows® XP
• Microsoft® eMbedded Visual C++ 4.0 or Virtual Studio 2005
• Platform SDK for TREK510
• 64MB DRAM
• CD‐ROM drive
• Monitor with VGA resolution at least
• Mouse
• 200MB free hard disk space at least
• TREK510 platform
• Let the host PC and TREK510 connect on the same USB1.1 to do kernel debugging if
necessary
• USB cable (bundled in the standard TREK510)
6.6.2 Building Windows CE program
By the platform SDK bundled with the standard TREK510, users can build the Windows CE
runtime application program by the eMbedded Visual Tools.
TREK‐510 User manual
43
Figure 6.11 Flow‐chart of Building Windows® Embedded CE 5.0 runtime
6.6.3 How to install SDK
For example copy Platform SDK file “**.msi” to your PC, and launch it. You can install SDK by
steps.
Step 1, Launch Platform SDK file, and then tap Next button.
Figure 6.12
TREK‐510 User manual
44
Step 2, Accept License Agreement and go next.
Figure 6.13
Step 3, Key in your information and go next.
TREK‐510 User manual
45
Figure 6.14
Step 4, Choose setup type.
Figure 6.15
Figure 6.16
TREK‐510 User manual
46
Step 5, Tap “Install” button to install SDK.
Figure 6.17
Install SDK…….
TREK‐510 User manual
47
Figure 6.18
Step6, Finish installing.
Figure 6.19
6.6.4 Running your application programs
After you implement application code, you should choose Advantech SDK to compile.
TREK‐510 User manual
48
Figure 6.20
6.6.5 SUSI
library for application program
TREK510 is targeted to be the embedded device for system integrator. System integrator
usually access platform relative IO, like backlight control, brightness control, etc. Advantech
especially provide one SUSI static library to system integrator. SUSI library includes some
useful APIs. System integrator just adds it to their application project, and then they can use
SUSI library functions.
Note: about SUSI library detail was showed in [SUSIV3.0RISCUser Manual(Hotkey2GPIO).doc]
SUSI library package include following content :
1, SUSI.lib
2, SUSI.h
3, SUSI user guide
The functions in SUSI include :
1, Screen on / off
2, Brightness set / get
3, Watchdog timer set / get / refresh
TREK‐510 User manual
49
4, Software / Hardware reset
5, Get bootloader version
6, Digital I/O access
TREK‐510 User manual
50
Chapter
Software demo utility
setup
This appendix explains the software
demo utility for TREK‐510.
Sections include:
z Introduction
z How to set up demo utility
TREK‐510 User manual
51
7.1
Introduction
To make the hardware easier to access for programmers, Advantech has
developed a demo utility in order to let customer test the functions on TREK‐510.
This document describes detailed information for each Advantech demo utility so
that application developers can become more familiar with using them.
For technical support, contact Advantech application engineers
worldwide. For news updates, visit our website: www.advantech.com
7.1.1 Execute J1939 demo utility
This section explains how to install the Advantech demo utility in Windows XP Pro
/ Embedded.
1. Execute the test program called “IMC_Demo”
Figure 7. 1 IMC demo utility
2. Click J1939: customer may connect directly to the truck; we use a car
simulator board below to explain how J1939 protocol can be executed.
First, connect to the simulator board to TREK‐510 CAN port and console PC,
once the simulator is powered on (connect to the truck), you can start getting
the data, just click [Read], you may get the data you need from the car
simulator, click [Read], you may transfer the data to Console
TREK‐510 User manual
52
Figure 7.3 J1939 test ‐1
Figure 7.4 J1939 test ‐2
7.1.2 Execute CAN demo utility
Figure 7. 9 CAN test
TREK‐510 User manual
53
1. Reset the module
2. Transmit CAN message
3. Set the polling rate of CAN message reception
4. Received CAN message.
5. Set up the filter of CAN message (only show the message ID)
7.2
RTC test
Execute “RTC test”
1. For RTC Time setting: You may set year, month, date, and time show as
below.
Figure 7.10 RTC test ‐1
Figure 7. 12 RTC test ‐3
TREK‐510 User manual
Figure 7.11 RTC test ‐2
Figure 7. 13 RTC test ‐4
54
2. RTC Alarm Setting: You may also set Alarm time; you may wake up the
system by the time you have set. Please refer to below figure 6.
Figure 7.14 RTC test ‐5
7.3
Vehicle Power Management
7.3.1 Power management Mechanism
The feature of Vehicle Power Management (VPM) is provided for users to
fulfill the special requirements on in‐vehicle applications.
Ignition on/off
„ Turn on the system by ignition
For the cases of in‐vehicle applications, ignition signal is often used to turn on or
shutdown system. When the system is in OFF state and ignition is turn ON, the VPM
controller will countdown ON_DELAY; once it counts to zero, the system will be turn on.
„ Shutdown the system by ignition
When the system is powered on and ignition is turn off, the OFF_EVENT_DELAY will start
to count down. During this stage, if the ignition is back to ON, VPM controller will stop
countdown and reset the OFF_EVENT_DELAY value. If OFF_EVENT_DELAY is keeping
counting to zero, VPM controller will send a event (power button press) to the system
and start to count HARD_OFF_DELAY. The application programs could watch this event to
do pre‐defined tasks, like storing the data and preparing to turn off system.
Once going into HARD_OFF_DELAY stage, this process will be irreversible. And if
HARD_OFF_DELAY counts to zero, the system power will be cut off abruptly.
Low battery protection
To avoid draining out the car battery, low‐battery protection is involved to ensure the
car battery is capable to start the vehicle. When the system is ON, VPM controller will
monitor the car battery voltage. If the battery voltage is lower than a programmable
threshold (LOW_THRESHOLD), VPM controller will go into LOW_DELAY stage and start
to count down. During the stage of LOW_DELAY countdown, if battery voltage is back
TREK‐510 User manual
55
above LOW_THRESHOLD, VPM controller will stop count down and leave this stage. If
LOW_DELAY counts to zero, VPM controller will send an event (power button press) to
notify the system, go into LOW_ HARD_DELAY stage and start to count down. Once
LOW_ HARD_DELAY counts to zero, VPM controller will cut off the system power
abruptly to avoid draining out the cat battery.
The table below lists the user programmable parameters for VPM features:
Default value
Acceptable range
ON_DELAY
2 second
1 ~ 18000 second
OFF_EVENT_DELAY
5 second
1 ~ 18000 second
HARD_OFF_DELAY
60 second
1 ~ 18000 second
LOW_THRESHOLD (12V mode)
11.42 V
10.09 ~ 12.25 V
LOW_THRESHOLD (24V mode)
22.44 V
21.11 ~ 23.28 V
LOW_DELAY
30 second
1 ~ 3600 second
LOW_ HARD_DELAY
60 second
1 ~ 3600 second
7.3.2
Power Management utility program
TREK‐510 User manual
56
Execute IMCDemo.exe file, see the icon below.
7.3.3
Power Management Parameter settings
The parameters for power management on TREK‐510 could be read or modified by Demo
utility (see the image below) or SDK/API.
Figure 7.15 Power management test utility
7.3.4
TREK‐510 power consumption
OS: Windows Embedded Standard
Burn‐in test V6.0
Idle Mode
100% Burn‐in Test Mode
w/o TREK‐303H
12V / 1.04A
12V / 1.20A
w/ TREK‐303H
12V / 1.51A
12V / 1.94A
*Doesn’t support S1, S3, S4
7.4
GPIO Test
TREK‐510 User manual
57
Off mode (S5)
12V / 1.75mA
1. Execute I/O Test, connect GPIO loopback, click Pin0→Set, the end which Read
the signal, the bulb will be light up, like wise to Pin1~Pin3. Next pick Digital
output to execute the same procedure. See figure 6.
Figure 7.16 DI/O test
a. Digital Output Î isolated relay driver output
b. Digital Input Î isolated dry contact input
Figure 7.17 Digital in
TREK‐510 User manual
58
Figure 7.18 Digital out
7.7
G‐sensor (3‐axis accelerometer)
A 3‐axis accelerometer is integrated in TREK‐510. This could be used to
characterize driver behavior such as hard accelerations, braking, and
cornering. This also can tell users other significant information that can be used in
accident reconstruction and etc. A code example is provided for customer
reference regarding how to access and configure G‐sensor. G‐sensor is located on
the motherboard inside the TREK‐510. Please refer the link
(http://www.analog.com/static/imported‐files/data_sheets/ADXL345.pdf) for the
G‐sensor datasheet.
TREK‐510 User manual
59
Appendix
TREK‐303
This
This appendix explains the
TREK‐303 detailed information
TREK‐510 User manual
60
Appendix A Paired with TREK‐303 Specifications
TREK‐303 Specification
Note!
TREK‐510 User manual
1.
The Brightness control is adjusted by the auto light sensor
in the front panel as default; it is also defined by button on
the front panel by manual.
2. The color LCD display
61
Pin out for TREK‐303 LVDS connector
TableA.2:SmartDisplayConnector
Pin
Signal
Pin
Signal
Backlight Enable input #
Panel Power Enable input #
LVDS Ground
Reset Button Input #
LVDS Clock +
LVDS Clock ‐
LVDS Ground
LVDS Ground
LVDS Data2 +
10
LVDS Data2 ‐
11
RS232 RXD1 #
12
RS232 TXD1 #
13
LVDS Data1 +
14
LVDS Data1 ‐
15
LVDS Ground
16
LVDS Ground
17
LVDS Data0 +
18
LVDS Data0 ‐
19
USB D‐
20
USB D+
21
USB Ground
22
USB Ground
23
+12VDC input (+/‐ 5%, max 1A)
24
+12VDC input (+/‐ 5%, max 1A)
25
+12VDC input (+/‐ 5%, max 1A)
26
+12VDC input (+/‐ 5%, max 1A)
27
Power Ground
28
Power Ground
29
Power Ground
30
Power Ground
31
RS232 RXD2 #
32
33
RS232 RTS2
34
35
Audio Ground
36
RS232 TXD2 #
Power Button Input # (connect
with system box)
Mono. Line‐in
TREK‐510 User manual
62
Pin assignment
P1
10 11
12
13 14
15
16
17 18
P2
10 11
12
13 14
15
16
17 18
Color Brown White Ground Brown red white Ground Ground Orange white
red Orange yellow white Ground Ground Green white
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Black
black
Black Black Black
Black
Black
Yellow green
purple
grey
Blue
white Ground yellow Green Blue Purple Grey white Black
Orange
Brown
TREK‐303 Hotkey Utility
Execute IMC demo utility
TREK‐510 User manual
63
red
blue
Figure A. 1 Hotkey utility
1. Execute “Hot Key test” program Î
2. Brightness level: You may set panel’s brightness from level 0 ~10, total 10
levels, when you finish setting the brightness level you want, please click
“Apply”. If you want to check the current brightness level of TREK‐303,
please click “Get”.
3. Duty cycle: You may set every level’s brightness strength, total 10 levels,
when you finish setting the brightness strength for each level, please click
“Apply”. If you want to check the current brightness strength on certain
level of TREK‐303, please click “Get”.
4. Light sensor: When the sensor has detected the change of the brightness
in the environment, the value will change. The lowest level of brightness,
the lowest value it is presented. On the contrary, the highest level of
brightness, the highest value it is presented.
5. Hotkey: the backlight brightness of hotkeys could be adjusted by setting
the value from 0 ~100.
6. Key Status: When you press Hot key, the status will change from 0 to 1.
7. Key function Definition: You may set the parameter to connect the
application program of the hot key.
TREK‐510 User manual
64
Appendix
Windows Embedded
CE 5.0 Component
List
This
TREK‐510 User manual
65
Appendix B
Windows® Embedded CE 5.0 Component List
Advantech
APPLICATIONS AND SERVICES DEVELOPMENT
Advantech
Pro.
Advantech
Pro. Plus
Core
Core
Pro.
Pro.
Plus
Active Template Library (ATL)
C Libraries and Runtimes
Runtime Type Information
Full C Runtime
Standard I/O (STDIO)
Standard I/O ASCII (STDIOA)
String Safe Utility Functions
Standard String Functions - ASCII (corestra)
COM Storage
DCOM Remote Access
Minimal COM (No OLE Support)
C++ Runtime Support for Exception Handling
and
Component Services (COM and DCOM)
Component Object Model
COM
CoCreateGuid functionality for
OLE32
COM Storage
DCOM
CoCreateGuid functionality for
OLE32
COM Storage
Speech Interface
Speech API (SAPI) 5.0
Microsoft English (US) Windows CE Speech
Recognizer (available in 4.2 only)*
Lightweight Directory Access Protocol (LDAP)
TREK‐510 User manual
66
Client
Message Queuing (MSMQ)
SOAP Reliable Messaging Protocol (SRMP)
MSMQ ActiveX Wrappers
Microsoft Foundation Classes (MFC)
Object Exchange Protocol (OBEX)
OBEX Inbox
OBEX File Browser
OBEX Server
OBEX Client
Pocket Outlook Object Model (POOM) API
SOAP Toolkit
Client
Server
Standard SDK for Windows CE
.NET Compact Framework
Smart Device Authentication Utility
.NET Compact Framework 2.0
SQL Server CE 2.0 .NET Data Provider
SQL Server 2000 .NET Data Provider
SQL Server CE 2.0
XML
XML HTTP
XML Query Languages (XQL)
XML SAX
XML Error Strings
OS Dependencies for .NET Compact
Framework 2.0
MSXML 3.0
XML Core Services and Document
Object Model
(DOM)
XML Stylesheet Language
Transformations (XSLT)
XML Minimal Parser
Exchange Client
APPLICATIONS - END USER
TREK‐510 User manual
67
ActiveSync
File Sync
Inbox Sync
Pocket Outlook Database Sync
CAB File Installer/Uninstaller
Microsoft Excel Viewer*
Microsoft Image Viewer*
Microsoft PDF Viewer*
Microsoft PowerPoint Viewer*
Microsoft Word Viewer*
File Viewers*
FLASH Update Sample Application
Games
Freecell
Solitaire
Help*
Inbox
Remote Desktop Connection
Remote Desktop Protocol (RDP)
User Interface Dialog Boxes
Smart Card Redirection
File Storage Redirection
Cut/Copy/Paste Clipboard Redirection
Serial and Parallel Port Redirection
Audio Playback Redirection
Printer Redirection
Filtered File Storage Redirection
Terminal Emulator
Windows Messenger
WordPad
CORE OS SERVICES
Battery Driver
Display Support
Serial Port Support
Parallel Port Support
Internet Appliance (IABASE) Support
Notification LED Support
TREK‐510 User manual
68
PNP Notifications
USB Host Support
USB HID Keyboard and Mouse
USB HID Keyboard Only
USB HID Mouse Only
USB Printer Class Driver
USB Storage Class Driver
USB Remote NDIS Class Driver
USB Human Input Device (HID) Class Driver
Debugging Tools
Keyboard Test Application
Touch Driver Test Application
Remote Display Application
Tiny Kernel Test Sample Application
Toolhelp API
LMemDebug Memory Debugging Hooks
UI based Notification
Non UI based Notification
Notification (Choose 1)
Power Management (Choose 1)
Power Management (Full)
Power Management (Minimal)
Device Manager
Kernel Features
Target Control Support (Shell.exe)
Fiber API
FormatMessage API
Memory Mapped Files
Message Queue - Point-to-Point
Extensible Authentication Protocol
Firewall
COMMUNICATIONS SERVICES AND NETWORKING
Networking Features
Domain Discovery
Extended DNS Querying and Update
(DNSAPI)
Secure DDNS
TREK‐510 User manual
69
Internet Connection Sharing (ICS)
IPSec v4
NDIS Packet Capturing DLL
NDIS User-mode I/O Driver
Network Bridging
Network Driver Architecture (NDIS)
Network Utilities (IpConfig, Ping, Route)
Reference Gateway User Interface
Remote Configuration Framework
TCP/IP
TCP/IPv6
Universal Plug and Play (UPnP)
Control Point API
Device Host API
Device Host API (Minimal Subset)
UPnP Tools
UPnP Audio-Video DCP
AV Control Point API
AV Device API
Gateway Logging
IP Helper API
Sample UPnP IGD Schema
Implementation
AV Renderer Sample
USB Flash Config Tool
Windows Networking API/Redirector
(SMB/CIFS)
Native Wi-Fi WLAN STA
Wired Local Area Network (802.3, 802.5)
Winsock Support
Networking - Local Area Network (LAN)
Native Wi-Fi WLAN Access Point
Components
Wireless LAN (802.11) STA - Automatic
Configuration
and 802.1x
Networking - Personal Area Network (PAN)
TREK‐510 User manual
70
Bluetooth
Bluetooth Protocol Stack with Transport
Driver
Support
Bluetooth Stack with Integrated
CSR Chipset
Driver
Bluetooth Stack with Universal
Loadable Driver
Bluetooth Stack with Integrated
SDIO Driver
Bluetooth Stack with Integrated
USB Driver
Bluetooth Stack with Integrated
UART Driver
Bluetooth Profiles Support
Bluetooth HS/HF and Audio
Gateway
Service
Bluetooth LAP and Configuration
Utility
Bluetooth DUN Gateway
Bluetooth PAN
Bluetooth HID – Keyboard
Bluetooth HID – Mouse
Bluetooth HID Device Support
IrDA
Networking - Wide Area Network (WAN)
Dial Up Networking (RAS/PPP)
AutoDial
Standard Modem Support for Dial Up
Networking
Point-to-Point Protocol over Ethernet
(PPPoE)
Telephony API (TAPI 2.0)
Unimodem support
Virtual Private Networking
PPTP
TREK‐510 User manual
71
L2TP/IPSec
Core Server Support
FTP Server
File Server
Peer Name Resolution Protocol (PNRP)
Identity Manager
Servers
File Server Customizable UI
Windows Peer-to-Peer Networking
Print Server
RAS Server/PPTP Server (Incoming)
Telnet Server
Web Server (HTTPD)
JScript 5.6
VBScript 5.6
Device Management ISAPI Extension
WebDAV Support
Web Server Administration ISAPI
Active Server Pages (ASP) Support
Web Proxy
Parental Controls
SNTP Server
SNTP Client with DST
Device Management Client
Simple Network Management Protocol (SNMP)
Simple Network Time Protocol (SNTP)
SNTP Automatic Updates and Server
Synchronization
DEVICE MANAGEMENT
FILE SYSTEMS AND DATA STORE
Compression
Database Support
File and Database Replication (Choose 1)
Bit-based
Count-Based
File System - Internal (Choose 1)
RAM and ROM File System
TREK‐510 User manual
72
ROM-only File System
Registry Storage (Choose 1)
Hive-based Registry
RAM-based Registry
Binary Rom Image File System
Storage Manager Control Panel Applet
EDB Database Engine
Partition Driver
CD/UDFS File System
FAT File System
Transaction-Safe FAT File System (TFAT)
Storage Manager
System Password
FONTS
Arial
Arial (Subset 1_30)
Arial Black
Arial Bold
Arial Bold Italic
Arial Italic
Comic Sans MS
Comic Sans MS Bold
Comic Sans MS
Courier New
Courier New (Subset 1_30)
Courier New Bold
Courier New Bold Italic
Courier New Italic
Georgia
Georgia Bold
Georgia Bold Italic
Georgia Italic
Impact
Kino
MSLogo
Symbol
Georgia
TREK‐510 User manual
73
Tahoma
Tahoma (Subset 1_07)
Tahoma Bold
Times New Roman (Subset 1_30)
Times New Roman Bold
Times New Roman Bold Italic
Times New Roman Italic
Trebuchet MS
Trebuchet MS Bold
Trebuchet MS Bold Italic
Trebuchet MS Italic
Verdana
Verdana Bold
Verdana Bold Italic
Verdana Italic
Webdings
Wingding
Input Method Manager (IMM)
Locale Services (Choose 1)
Times New Roman
Trebuchet MS
Verdana
INTERNATIONAL
National Language Support (NLS)
English (US) National Language Support only
Tahoma (subset 1_08)
Tahoma Bold (subset 1_08)
Arial (subset 1_08)
Arial Bold (subset 1_08)
Courier New (subset 1_08)
Chinese (Simplified)
Agfa AC3 Font Compression
Locale Specific Support
Arabic
Fonts
Keyboard
Arabic Keyboard (101)
TREK‐510 User manual
74
Fonts
GB18030 Data Converter
Input Method Editor (Choose 1)
MSPY 3.0 for Windows CE
Small
Pocket IME
SimSun & NSimSun (Choose 1)
SimSun & NSimSun
SimSun & NSimSun (Subset
2_20)
SimSun & NSimSun (Subset
2_50)
SimSun & NSimSun (Subset
2_60)
SimSun & NSimSun (Subset
2_70)
SimSun & NSimSun (Subset
2_80)
SimSun & NSimSun (Subset
2_90)
SC_Song
MSPY 3.0 for Windows CE
Database
(Choose 1)
1.1 MB - Minimal
Database
1.3 MB - Compact
Database
1.7 MB - Standard
Database
Double Spelling (Shuang Pin) soft
keyboard –
Large
Double Spelling (Shuang Pin) soft
keyboard –
Double Spelling (Shuang Pin)
soft
keyboard – Small
TREK‐510 User manual
75
Chinese (Traditional)
Agfa AC3 Font Compression
Fonts
MS Ming
Input Method Editor
MingLiU & PMingLiU (Choose 1)
MingLiU & PMingLiU
MingLiU & PMingLiU (Subset
2_70)
MingLiU & PMingLiU (Subset
2_80)
MingLiU & PMingLiU (Subset
2_90)
Pocket IME
Input Methods
Input by Radical (Chang Jei)
Handwriting Recognizer Engine
(HWX)
MboxCHT HWX Sample UI
Phonetic Input (Bopomofo)
English (Worldwide)
Input Methods
Handwriting Recognizer Engine
(HWX)
English (U.S.)
Input Methods
Transcriber Handwriting
Recognition
Application
French
Input Methods
Transcriber Handwriting
Recognition
Application
German
Input Methods
Transcriber Handwriting
TREK‐510 User manual
76
Recognition
Application
Hebrew
Tahoma (subset 1_08)
Arial (subset 1_08)
Tahoma Bold (subset 1_08)
Arial Bold (subset 1_08)
Courier New (subset 1_08)
Fonts
Keyboard
Hebrew Keyboard
Indic
Hindi
Fonts
Mangal
Keyboard
Hindi Traditional Keyboard
Marathi
Fonts
Mangal
Keyboard
Marathi Keyboard
Punjabi
Fonts
Raavi
Keyboard
Punjabi Keyboard
Telugu
Fonts
Gautami
Keyboard
Telugu Keyboard
Gujarati
Fonts
Shruti
Keyboard
Gujarati Keyboard
TREK‐510 User manual
77
Kannada
Agfa AC3 Font Compression
Fonts
MS Mincho & MS PMincho
Input Method Editor (Choose 1)
Fonts
Tunga
Keyboard
Kannada Keyboard
Tamil
Fonts
Latha
Keyboard
Tamil Keyboard
Japanese
MS Gothic (Choose 1)
MS Gothic & MS PGothic &
MS UI Gothic
MS Gothic & MS PGothic &
MS UI Gothic
(Subset 1_50)
MS Gothic & MS PGothic &
MS UI Gothic
(Subset 1_60)
MS Gothic & MS PGothic &
MS UI Gothic
(Subset 1_80)
MS Gothic & MS PGothic &
MS UI Gothic
(Subset 1_90)
MS Gothic & MS PGothic &
MS UI Gothic
(Subset 1_70)
MS Gothic & MS PGothic
(Subset 30)
MS Gothic & MS PGothic
(Subset
30_1_19)
TREK‐510 User manual
78
IME 3.1
IME 3.1 Database (Choose 1)
Standard Database
Compact Database
Optional UI Components
Dictionary Tool
Properties Dialog Box
Name/Place Database
Supplemental Database
Test IME
Input Methods
HWX Sample UI
Multibox HWX Sample UI
Advanced Settings
Dialog Box
(Landscape mode
only)
System Tray Icon
Manager
Pocket IME (Choose Additional
Databases)
All Characters List
Handwriting Recognizer Engine
(HWX)
Character Auto Complete –
Kana Soft Keyboard
Romaji/English Soft Keyboard
Search by Radical
Search by Stroke
Agfa AC3 Font Compression
Fonts
Gulim (GL_CE)
Gulim & GulimChe (Choose 1)
Korean
Gulim & GulimChe (Subset
1_30)
Gulim & GulimChe (Subset
TREK‐510 User manual
79
1_40)
Gulim & GulimChe (Subset
1_50)
Multilingual User Interface (MUI)
Unicode Script Processor for Complex Scripts
Gulim & GulimChe (Subset
1_60)
Input Method Editor
IME 97
Input Methods
Handwriting Recognizer Engine
(HWX)
MboxKOR HWX Sample UI
Korean Soft Keyboard Sample
Thai
Fonts
Tahoma (subset 1_08)
Keyboard
Thai Kedmanee Keyboard
Internet Client Services
Browser Application
Internet Explorer 6.0 Sample Browser
TV-Style Navigation Components
Internet Explorer 6.0 for Windows CE Standard
Components
Pocket Internet Explorer
Internet Explorer 6.0 for Windows CE Components
Internet Explorer Browser Control Host
Internet Explorer HTML/DHTML API
Internet Explorer HTML Application
Filter and Translation
Internet Explorer Plug-in Image Decoder
API
Internet Explorer PNG Image
Decoder
Internet Explorer Theme Library
TREK‐510 User manual
80
Internet Explorer Multiple-Language Base
API
Internet Explorer RPC Support
Internet Explorer TV-Style Navigation
Fixed-Width Layout
Directional Tabbing
Disable Vertical Scroll Bar and Events
Customizable Font Range
Internet Explorer Multiple-Language Full
API
Optional Charset/Encoding in registry
URL Moniker Services
Windows Internet Services
Passport SSI 1.4 Authentication
Platform for Privacy Preferences (P3P)
XML Data Islands
XML MIME Viewer
Pocket Internet Explorer HTML View (WEBVIEW)
Internet Options Control Panel
Scripting
Script Authoring (Jscript)
Script Encode (Jscript)
Script Authoring (VBScript)
Script Encode (VBScript)
MsgBox and InputBox support
JScript 5.6
VBScript 5.6
GRAPHICS AND MULTIMEDIA TECHNOLOGIES
Graphics
Raster Fonts Support
V1 Font Compatibility
Alphablend API (GDI version)
Gradient Fill Support
Multiple Monitor Support
Imaging
Still Image Codec Support (Encode and
Decode)
TREK‐510 User manual
81
Still Image Decoders
PNG Decoder
BMP Decoder
GIF Decoder
ICO Decoder
JPG Decoder
GIF Encoder
BMP Encoder
JPG Encoder
PNG Encoder
Direct3D Mobile
DirectDraw
GSM 6.10 Codec
MSFilter Codec
Still Image Encoders
Audio
Audio Compression Manager
Waveform Audio
Media
Digital Rights Management (DRM)
DRM for Portable Devices
DRM License Acquisition OCX
Streaming Media Playback (requires WMP
application)
WMA and MP3 Local Playback
WMA and MP3 Streaming (requires WMP
application)
Digital Rights Management
DirectShow
DirectShow Core
DirectShow Display
DirectShow Error Messages
DMO Wrapper Filter
ACM Wrapper Filter
AVI Filter
MPEG-1 Parser/Splitter
Media Formats
TREK‐510 User manual
82
Audio Codecs and Renderers
G.711 Audio Codec
GSM 6.10 Audio Codec
IMA ADPCM Audio Codec
MP3 Codec
MPEG-1 Layer 1 and 2 Audio
Codec
MS ADPCM Audio Codec
Waveform Audio Renderer
WMA Codec
WMA Voice Codec
Wave/AIFF/au/snd File Parser
DirectShow Video Renderer
MPEG-1 Video Codec
MS RLE Video Codec
Overlay Mixer
Video Codecs and Renderers
Video/Image Compression
Manager
WMV/MPEG-4 Video Codec
DVD-Video
DVD-Video
DVD-Video Samples
Windows Media Player
Windows Media Player
Windows Media Player OCX
ASX v1 and M3U File Support
ASX v2 File Support
ASX v3 File Support
Windows Media Technologies
Windows Media Multicast and
Multi-Bit Rate
NSC File Support
Windows Media Streaming from
Local Storage
Windows Media Streaming over
HTTP
TREK‐510 User manual
83
Windows Media Streaming over
MMS
SECURITY
Authentication Services (SSPI)
NTLM
Kerberos
Schannel (SSL/TLS)
Cryptography Services (CryptoAPI 1.0) with High
Encryption
Provider
Certificates (CryptoAPI 2.0)
Cryptographic Messaging (PKCS#7)
Personal Information Exchange
Standard
(PKCS #12)
Diffie-Hellman/DSS Provider
Smart Card Encryption Provider
Local Authentication Sub-System
Password Local Authentication Plug-in
Microsoft Certificate Enrollment Tool Sample
Credential Manager
Minimal GWES Configuration
Minimal GDI Configuration
Minimal Input Configuration
Minimal Window Manager Configuration
SHELL AND USER INTERFACE
Graphics, Windowing and Events
Shell
Graphical Shell (Choose 1)
Standard Shell
Windows Thin Client Shell
AYGShell API Set
Command Shell
Console Window
Command Processor
User Interface
Accessibility
TREK‐510 User manual
84
Common Dialog Support
Controls Option B
Control Panel Applets
Customizable UI
Menu Tool Tip
Mouse
Network User Interface
Overlapping Menus
Software Input Panel
SIP for Small Screens
SIP for Large Screens
Touch Screen (Stylus)
Quarter VGA Resources - Portrait Mode
Common Controls
Windows XP-like Sample Skin
Software-based Input Panel Driver
Software-based Input Panel (SIP)
(Choose 1 or more)
Animation Control
Common Control
Windows CE Error Reporting
Error Report Generator
Report Upload Client
Error Report Transfer Driver
Error Reporting Control Panel
Phone IME
PC Authentication
VAIL Database Store
Phone Provisioner
Reference Media Manager
Report Upload Client User Interface
VOICE OVER IP PHONE SERVICES
Telephony User Interface
VoIP Application Interface Layer (VAIL)
Real-time Communications (RTC) Client API
SIREN/G.722.1 Codecs
TREK‐510 User manual
85
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written
permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2010
TREK‐510 User manual
86
TREK‐510 User manual
87
FCC ID: M82-TREK-510 This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
“Complies with CANADA RSS-210
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures: -Reorient or relocate the receiving antenna. -Increase
the separation between the equipment and receiver. -Connect the equipment
into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
b. FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including
interference that may cause undesired operation
Notes and Warnings to the User and Installer:
Caution:
This Installation Guide is intended for use by the professional wireless LAN
system installer.
The device cannot be sold retail, to the general public or by mail order. It must
be sold to dealers or have strict marketing control.
Warning: It is the responsibility of the professional installer to ensure that the
system is used exclusively for fixed, point-to-point operations.
Warning: When using the device in the United States (or where FCC rules
apply), it is the responsibility of the professional installer to ensure to control
the output power not greater then the application.
Who Should Use this Guide:
Installation of this device should be accomplished only by a qualified wireless
LAN system installer who is: -Knowledgeable of the use, installation and
configuration procedures and associated networking
components. -Knowledgeable of each system component’s equipment User
and Installation Guide. -Knowledgeable of the installation and configuration
procedures for the site’s network infrastructure system and wiring.
-Knowledgeable of the installation procedures, safety, and code
requirements for the site’s antenna, antenna mast, antenna cabling, and
installation. We highly recommend that the antenna installation be performed
by a qualified antenna installation professional.
Users should not attempt to make such connections themselves, but should
contact the appropriate electrical inspection authority, or electrician, as
appropriate.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 89
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:81dc3494-46ef-4532-ac8d-7ddab15d346e
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Modify Date                     : 2011:10:12 23:34:40+08:00
Create Date                     : 2011:10:12 23:31:58+08:00
Metadata Date                   : 2011:10:12 23:34:40+08:00
Document ID                     : uuid:7802f909-f04c-4322-aecb-3333408110cc
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools