Advantech Co WISE-2400 BLE/ Wi-Fi Intelligent Sensor Gateway User Manual MFP Print Server Quick Installation Guide

Advantech Co Ltd BLE/ Wi-Fi Intelligent Sensor Gateway MFP Print Server Quick Installation Guide

Users Manual

WISE-2400-User Manual PRODUCT INTRODUCTION 1. Package Contents Before you start using this product, please check if there is anything missing in the package and contact your dealer to claim the missing item(s):  BLE/ Wi-Fi Intelligent Sensor Gateway (WISE-2400)  USB Cable (60cm)  User Manual  USB Adapter 5V/1A 2. LED & Button Definitions Front Panel
1 LEDs Color Status Description Power Status Blue ON Power on OFF Power off Active Status Blue BLINK Data Transmission Red BLINK Data Transmission failed Rear Panel Items Description Power ON/OFF Micro USB Port USB Power connector 3. Hardware Installation Step 1: Connect the power adapter to the WISE-2400 Plug one end of the power adapter into a power outlet and connect the other end to the 5V interface of the device.
2 Step 2: Fixed WISE-2400 with mounting kit Please follow below steps. to mount the WISE-2400.
3 4. GETTING STARTED A. First 2400 setting Start to use WISE-2400, please follow below flowchart to do the setting.
4 B. WISE-2400 Default Setting WISE-2400 default config as following table. Please follow the setting item to match wifi and RTLS server setting environment. Config Value Description SSID WISE_AP SSID of Connect AP security key 12345678 Security key of connected AP security type WPA/WPA2 Security type of connected AP Server IP 192.168.2.58 Server port 4242 WISE-2200W port 7000 For remote config connection Battery low power alert 40 Send alert if battery is low power RTLS Operation on/off off Turn on/off RTLS function Operation mode client Switch operation mode of RTLS Scan interval 10 Setting scan interval of RTLS function G-sensor sensitivity off Turn on/off G-sensor and set sensitivity(2G~16G), RTLS data will be sent if G-sensor is triggered Wifi AP config Key Config Note SSID WISE_AP key 12345678 Security type WPA RTLS Server config IP 192.168.2.58 port 4242 Factory default C. WISE-2400 connection Start the RTLS server with Wifi AP, then open WISE-2400 and WISE-2200B , WISE-2400 will be automatically registered to the RTLS server.
5 Can check all the WISE-2200B status from RTLS server "DEVICE MANAGEMENT "function.
6 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Navigation menu