Aeon Labs ZW078 HEAVY DUTY SMART SWITCH GEN5 User Manual 501001000001 Heavy Duty Smart Switch AL001 AA 1

Download:
Mirror Download [FCC.gov]
Document ID	2268204
Application ID	t7csZTU7J6R0F5YDS3xz9w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	150.95kB (1886863 bits)
Date Submitted	2014-05-15 00:00:00
Date Available	2014-05-15 00:00:00
Creation Date	2014-02-11 14:26:03
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2014-04-28 11:32:28
Document Title	501001000001 Heavy Duty Smart Switch_AL001 AA-1
Document Creator	CorelDRAW
Document Author:	Administrator

Your Heavy Duty Smart Switch
Important: A licensed electrician with knowledge and
understanding electrician systems and electrical safety
should complete the electrical installation.
Status LED
Heavy Duty Smart Switch Gen5
3. Preparing the wires you will be attaching to your
Heavy Duty Smart Switch by stripping the wires to the
necessary length. Add wire terminals to each wire.
The wires please use the minimum AWG10 #, or AWG8#.
Action Button
Wire terminals
View the digital manual:
http://aeot.ec/spprt/heavyduty
Action button: Used for Heavy Duty Smart Switch’s ZWave network inclusion and exclusion and to manually
turn on/off;
4. Wire according to the following diagram, as shown in
the figure, connect each live lines(L1,L2) from Air Break
Switch to corresponding terminals that marked L1 and L2
on the Heavy Duty Smart Switch, if there is Neutral line
and ‘GND’, please connect to the terminals which market
‘GND’ and ‘N’ on Heavy Duty Smart Switch, similarly wire
the electric load with Heavy Duty Smart Switch. Then
tighten screws to the wire terminals.
Adding/Including/Pairing your Heavy Duty
Smart Switch into a Z-Wave Network
To add your Heavy Duty Smart Switch to your Z-Wave
network with a Z-Stick, bring your Z-Stick near your
Heavy Duty Smart Switch then press the button on the ZStick to begin the Z-Wave inclusion process.
When your Heavy Duty Smart Switch is first powered on
and it’s not a part of a Z-Wave network, its Status LED will
blink. If it’s not blinking see the tip below. Press your
switch’s Action button to connect it to the Z-Stick. If it’s
successfully added to the network its Status LED will stop
blinking or pulse steadily. If this fails, repeat the above
steps.
Tip: If the Status LED of your Heavy Duty Smart Switch
does not blink when it’s first powered up, it means that
your switch is already part of another Z-Wave network. To
rectify this, first follow the subsequent Removing
instructions before following the Adding/Including/Pairing
steps above.
Important: You must make sure the wire terminals
connected firmly with each corresponding terminals on
the Heavy Duty Smart Switch.
Action Button
Status LED: Indicates the switch’s status;
Terminals: There are two groups of terminals. As
marked of the silk print, AC Power be connected to main
power, Load for electric load.
N L2
Load
L1
GND
GND
L2
Acpower
L1 N
Installation
Important : Heavy Duty Smart Switch MUST wired
behind an air break switch for safety and electric
appliance protection .
Before wiring, you must switch off the Air Break Switch
and confirm the circuit power is down, if the Air Break
Switch is out of sight, please lock it to ‘OFF’ position and
tag it to prevent unexpected application of power:
1. Mount Heavy Duty Smart Switch on a wall as shown in
following figure:
Package Contents
Heavy Duty Smart Switch .... ............... ......
8AWG Wire terminal ................................
10AWG Wire terminal ..............................
Screws ...................................................
Load
Air Break Switch
OR
5. Power on your Heavy Duty Smart Switch. At this stage
you need to add it to your Z-Wave network. For
instructions on how to do this, please refer to the
following “Z- Wave Network Instructions” section.
To add your Heavy Duty Smart Switch to your Z-Wave
network with a Minimote, bring your Minimote to be
within range of your Heavy Duty Smart Switch then press
the remote button labelled “Include” on the Aeon Labs
Minimote to begin the Z-Wave inclusion process.
6. Once added to your Z-Wave network, replace your
Heavy Duty Smart Switch’s shell, and refasten to the
shell. Your installation is now complete.
x1
x8
x8
x2
Instruction Manual.................................... x1
Include
Aeotec by Aeon Labs Heavy Duty Smart Switch
Aeotec by Aeon Labs’ Heavy Duty Smart Switch is
a Z-Wave switch controller that can also report the
wattage energy usage and KWH usage of the
device wired in to it. As part of its switching
functionality, Heavy Duty Smart Switch can be
controlled by other Z-Wave devices to turn loads
on or off. It can bear up to 40 amps current of
resister loads.
It also act as a repeater, forwarding Z-Wave
command messages to destination nodes if the
originating controller is out of range from the
destination node.
By taking advantage of the Z-Wave mesh network,
commands can be routed to their destination via
intermediary Z-Wave products. Products that are
Z-Wave certified can be used and communicate
with other Z-Wave certified device.
2. Loosen your switch’s lower screw to release its shell.
Remove the shell to reveal the inner electronics.
Z-Wave Network Instructions
Heavy Duty Smart Switch must be paired(included) into a
Z-Wave network before it can receive Z-Wave commands
to turn on/off and report its energy usage. The Heavy
Duty Smart Switch can only communicate to devices
within its own Z-Wave network.
Note: The LED on the Heavy Duty Smart Switch will blink
if it is currently not operating within a Z-Wave network.
Tip: Before including / excluding Heavy Duty Smart
Switch from your Z-Wave network, it’s recommended that
you turn off most of the appliances connected to it. This
will help to prevent load damage.
When your Heavy Duty Smart Switch is first powered on
and it’s not a part of a Z-Wave network, its Status LED
will blink. If it’s not blinking see the tip below. Press your
switch’s Action button to connect it to the Z-Stick. If it’s
successfully added to the network its Status LED will
stop blinking or pulse steadily. If this fails, repeat the
above steps.
Tip: If the Status LED of your Heavy Duty Smart Switch
does not blink when it’s first powered up, it means that
your switch is already part of another Z-Wave network. To
rectify this, first follow the subsequent Removing
instructions before following the Adding/Including/Pairing
steps above.
To include the Aeon Labs Heavy Duty Smart Switch with
other controllers, please consult the operation manual for
these controllers on how to include Z-Wave products into
an existing network.
Removing your Heavy Duty Smart Switch From
a Z-Wave Network
You can remove your Heavy Duty Smart Switch from
your Z-Wave network at any time. To do this you need
use your main controller such as a Z-Stick or Minimote.
If you are using a Z-Stick:
If your Z-Stick is plugged into a gateway or a computer,
unplug it.
1. Bring your Z-Stick near your Heavy Duty Smart
Switch.
2. Press the Action Button on your Z-Stick.
3. Press the Action Button on your Heavy Duty Smart
Switch.
4. I f y o u r H e a v y D u t y S m a r t S w i t c h h a s b e e n
successfully removed from your network, its light will
blink. If the removal was unsuccessful its light will not
blink.
5. Press the Action Button on the Z-Stick to make it out of
removal mode.
If you are using a minimote:
1. Bring your Minimote near your Heavy Duty Smart
Switch.
2. Press the Remove Button on your Minimote.
3. Press the Action Button on your Heavy Duty Smart
Switch.
4. I f y o u r H e a v y D u t y S m a r t S w i t c h h a s b e e n
successfully removed from your network, its light will
blink. If the removal was unsuccessful its light will not
blink.
5. Press any button on your Minimote to make it out of
removing mode.
Turn Your Heavy Duty Smart Switch On or Off
Your Heavy Duty Smart Switch can be turned on or off
through the use of Z-Wave commands built into Z- Wave
certified controllers and gateways. The specific Z-Wave
commands supporting this function are the Basic
Command Class and Binary Switch Command Class.
Please consult the operation manual for these
controllers for specific instructions on controlling your
Heavy Duty Smart Switch.
Monitoring Power Consumption
Your Aeon Labs Heavy Duty Smart Switch can report
Watts energy usage or KWh energy usage to a Z-Wave
gateway or controller. If this function is supported by
the gateway/controller, the energy consumption will be
displayed in its user interface. The specific Z-Wave
commands supporting energy monitoring are the Meter
Command Class and Multilevel Sensor Command
Class. Automatic reports go to the only association
group 1, which is setup via the Association Command
Class. Please also consult the operation manual for
these gateways/controllers for specific instructions on
monitoring your Heavy Duty Smart Switch.
Technical Specifications
Model number: DSC10-ZWUS
Waterproof: IP44
Power Consumption: 1W
Ratings: 240VAC,50/60Hz(2Phases L1,L2) ;
Maxim 9600 Watts 40A Resister;
240VAC 5HP AC Motor;
RF range: 300ft/100m outdoor;
Endurance of 10ms period peak current of 1440A
Warranty
Aeon Labs warrants to the original purchaser of
Products that for the Warranty Period (as defined
below), the Products will be free from material defects
in materials and workmanship. The foregoing warranty
is subject to the proper installation, operation and
maintenance of the Products in accordance with
installation instructions and the operating manual
supplied to Customer. Warranty claims must be made
by Customer in writing within thirty (30) days of the
manifestation of a problem. Aeon Labs' sole obligation
under the foregoing warranty is, at Aeon Labs' option,
to repair, replace or correct any such defect that was
present at the time of delivery, or to remove the
Products and to refund the purchase price to
Customer.
The "Warranty Period" begins on the date the Products
is delivered and continues for 12 months.
Any repairs under this warranty must be conducted by
an authorized Aeon Labs service representative and
under Aeon Labs' RMA policy. Any repairs conducted
by unauthorized persons shall void this warranty.
Excluded from the warranty are problems due to
accidents, acts of God, civil or military authority, civil
disturbance, war, strikes, fires, other catastrophes,
misuse, misapplication, storage damage, negligence,
electrical power problems, or modification to the
Products or its components.
Aeon Labs does not authorize any person or party to
assume or create for it any other obligation or liability
in connection with the Products except as set forth
herein.
Aeon Labs will pass on to Customer all manufacturers'
Material warranties to the extent that they are
transferable, but will not independently warrant any
Material.
Customer must prepay shipping and transportation
charges for returned Products, and insure the
shipment or accept the risk of loss or damage during
such shipment and transportation. Aeon Labs will ship
the repaired or replacement products to Customer
freight prepaid.
Customer shall indemnify, defend, and hold Aeon Labs
and Aeon Labs' affiliates, shareholders, directors,
officers, employees, contractors, agents and other
representatives harmless from all demands, claims,
actions, causes of action, proceedings, suits,
assessments, losses, damages, liabilities,
settlements, judgments, fines, penalties, interest,
costs and expenses (including fees and disbursements
of counsel) of every kind (i) based upon personal injury
or death or injury to property to the extent any of the
foregoing is proximately caused either by a defective
product (including strict liability in tort) or by the
negligent or willful acts or omissions of Customer or its
officers, employees, subcontractors or agents, and/or
(ii) arising from or relating to any actual or alleged
infringement or misappropriation of any patent,
trademark, mask work, copyright, trade secret or any
actual or alleged violation of any other intellectual
property rights arising from or in connection with the
products, except to the extent that such infringement
exists as a result of Aeon Labs' manufacturing
processes.
IN NO EVENT SHALL AEON LABS BE LIABLE FOR
ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL
OR CONSEQUENTIAL DAMAGES, OR DAMAGES
FOR LOSS OF PROFITS, REVENUE, OR USE
INCURRED BY CUSTOMER OR ANY THIRD PARTY,
WHETHER IN AN ACTION IN CONTRACT, OR TORT,
O R O T H E RW I S E E V E N I F A D V I S E D O F T H E
POSSIBILITY OF SUCH DAMAGES. AEON LABS'
LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY
FOR ANY CAUSE OF ACTION ARISING IN
CONNECTION WITH THIS AGREEMENT OR THE
SALE OR USE OF THE PRODUCTS, WHETHER
B A S E D O N N E G L I G E N C E , S T R I C T L I A B I L I T Y,
BREACH OF WARRANTY, BREACH OF AGREEMENT,
O R E Q U I TA B L E P R I N C I P L E S , I S E X P R E S S LY
L I M I T E D T O , AT A E O N L A B S ' O P T I O N ,
REPLACEMENT OF, OR REPAYMENT OF THE
P U R C H A S E P R I C E F O R T H AT P O R T I O N O F
PRODUCTS WITH RESPECT TO WHICH DAMAGES
ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING
IN CONNECTION WITH THIS AGREEMENT OR THE
SALE OR USE OF PRODUCTS SHALL BE DEEMED
WAIVED UNLESS MADE IN WRITING WITHIN
THIRTY (30) DAYS FROM AEON LABS'S DELIVERY,
OR THE DATE FIXED FOR DELIVERY IN THE EVENT
OF NONDELIVERY.
THE INDEMNITY AND WARRANTY IN ABOVE ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER
I N D E M N I T I E S O R WA R R A N T I E S , W H E T H E R
EXPRESS OR IMPLIED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
FCCNOTICE (for USA)
THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY
U N A U T H O R I Z E D M O D I F I C AT I O N S T O T H I S
EQUIPMENT. SUCH MODIFICATIONS COULD VOID
T H E U S E R ' S A U T H O R I T Y TO O P E R AT E T H E
EQUIPMENT.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consul the dealer or an experienced radio/TV
technician for help.
Warning
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact your local government for information
regarding the collection systems available.
Certifications (regional)
Version:501001000001-AA
www.aeotec.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Administrator
Title                           : 501001000001 Heavy Duty Smart Switch_AL001 AA-1
Create Date                     : 2014:02:11 14:26:03+08:00
Creator Tool                    : CorelDRAW
Modify Date                     : 2014:04:28 11:32:28+08:00
Metadata Date                   : 2014:04:28 11:32:28+08:00
Producer                        : Corel PDF Engine Version 14.0.0.701
Document ID                     : uuid:06f1cca8-d2eb-4cbf-91c6-c1c5e7d31d7d
Instance ID                     : uuid:0fae35b1-59c8-42d4-b31c-5c30df1ead6f
Page Count                      : 2
Author                          : Administrator

EXIF Metadata provided by EXIF.tools