Aerotron Repco Systems UHFHH-01 HANDHELD FM TWO WAY LAND MOBILE RADIO User Manual USERS MANUAL
Aerotron Repco Systems Inc. HANDHELD FM TWO WAY LAND MOBILE RADIO USERS MANUAL
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 60408 |
| Application ID | drNo4sUgVVA4ZiFz/rYrDg== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 84.52kB (1056463 bits) |
| Date Submitted | 1999-09-24 00:00:00 |
| Date Available | 1999-12-22 00:00:00 |
| Creation Date | 1999-09-23 16:55:04 |
| Producing Software | Photoshop PDF Plug-in 1.0 |
| Document Lastmod | 1999-09-23 16:55:43 |
| Document Title | USERS MANUAL |
| Document Creator | Photoshop PDF Plug-in 1.0 |
General Information
1.4.1 FEATURE AND OPERATION
1) PowerNotume Control Switch
Power Orr/OH and Volume control snitch. As turning dockwisflCW) direction, power turns on,
and continuous CW turning makes volume louder. Turning counter clockwise(CCW) direction
makes volume weaker and power turns off when tuming completely.
2) Antenna Connector
A connector tor smell whip antenna or etttemel antenna.
3) Earphone Jack
A jack tor earphone and eaaernal speaker.
Inmmal speekerwill not operate when the earphone or enamel speaker is used.
4) Enemal Mlc and Charger Jack
External mic or chargtng terminal can be connected.
or CAUTtON a Power snitch must he turner! otf during charging the barren, pack.
5) Tx Swltoh
Changing switch between ‘l'x and Rx mode. Must be pressed to transmit.
6) Speaker
ngh performance speaker with e ohm Is employed.
7) MIC
Keep your mouth apart from the MIC properly and talk es usual voioe strength on transrnleeton.
8) Battery Look
For detaching the battery pack from the main transceiver unlt. push and hold up this look and push
battery pack to ten.
9) Battery Pack
By using high capacity 1.5V battery pack. much longer operation is possible.
10) Program Connector
For Injeding trequenoies. tone to prevent lnterterenoe and other necessary infonnetlon lrorn PC or
other radios. Turn the screw or! and uncover. Then connect a programming cable for PC or a
cloning cable for other radios.
11) status Lamp
3) Red lamp Turns on in Tx and green in Rx.
D) At low battery. m1 lamp is Blinking.
c) Yellow lamp luht in transmitting ID and stone.
ti) When the programmed CTCSSJCDCSS is dirterent trorn the received one. green temp is
blinking.
12) LCD lamp switch [LMP]
For LCD olsplay Onlotl. This lamp shall be turned oil autommically In 5 seconds after tumlng on. it
you want to turn on the lamp continuously. press and hold the switch tor more than 2 seconds alter
lumtng the radio on.
mam mc.
mow. ram-or
“r": _..Qfi_. 99-07-10
General lntonnatlon
13) Channel Switch tor 5-Tone Memory Number“ V ]
Switch for changing memory number. A is for increment or channels and V is for decrement. It
pressed and held in more than 1 second. channel changes rapidly.
14) Scan Switch [sort]
This which Is tor emefing into scan mode.
15) Monilor Switch [MON]
For monitor Onion. in monitormode. signal can be received regardless ol CTCSSICDCSS squelch
lecture which prevents interference. If you want to receive the white noise with disabling noise
squelch function, press and hold this snitch for more than 2 seconds. This monitor feature can be
disabled by Pc programmer.
16) Call Switch [cm
Using for calling the other user in Stone call mode.
17) Funuiun Key [FUN]
For operating additional functions. this key should be pressed and held until the other witches at
the hon! panel are pressed. This key can be programmed to patient: any 0! (allowing function.
e) Switching High and Low RF output 2 FUN sw t r [H.l.]
b) Front Switch look or unlock : FUN sw # SCN M. |
c) Alan'h anion : FUN w + MON M Q 1
d) Mohlng lollrom Stone call and general mode : FUN sw + CAL 914 it]
13) LCD dismay
The LCD window Is optimized to provide rapid access to information and message oonceming the
progress of your call mode and the saws of your radio.
L_______ ___ _ _ ___ __ _
. [HGH]. [LOW] indicates either high or low RF oulpul
. [OTC]. IDCSI zit-dimes the current channel using CTCSS or 00088
, [ ta 1 :indioates lront panel switch look
, [ g l zindicates alarm ONIOFF
, SGN zindioates scan mode
. MON zindroaies monitor mode
. SEL zindioates 5 tone call mode
. 83 zindicales channel number of cross or 00058.
This has 83 codes and that has 38 lrequencies
. Chi-99 11ndlcates 99" channel is selected
memos-never) erst-ms. INC-
Pocuxttfi 41! 99-07-10
General lntormalion
. UL rinoicales certain channel is UnLoolted
. UNLOCK zindieates UNLOCK in 5 tone call mode
. OFF :Indioates error in power source
. FROG :prog ram mode
zcloning mode
zindirzies that stoning Is in progress
. success zoionlng is computed successimly
. ERROR indicates error in cloning progress
. EPERROR zindieotes error in memory (EEPROM)
. SL—99 : program mode tor scan list
Pn-ao : program mode for priority channel
1.4.2 SPECIAL FEATURES
1)
e)
b)
I1)
6)
27
8)
b)
C)
d)
a]
3)
To input frequencies and other data.
Screw out a bolt in program connector and uncover the guide. Then connect the programing
pen in radio to Pc by programming cable.
As pressing A r snitch, turn on the radio. Then the radio would be programming mode and
‘PROG‘ message displayed on LCD window.
Using PC programmer sotiware. you can input frequencies and other data to the radio.
In order to quit programming mode, turn off the radio.
Cloning Between Radios
Scam out each boil in programming connectors or both radios (one is for transmitting data
and the other for receiving data) and uncover the each guide. Then. link between two radios
by programming cable.
As pressing Tx switch. turn on the radio tor transmitting data. Then you can hear two short
tones. And It goes into cloning mode and the radio displays ‘don' on LCD windows
As pressing A 1 switch. tum on the radio for receiving data. Than the radio would no
programming mode and the radio displays 'PROG' on LCD windows
When pressing Tx switch of radio for transmitting data. cloning wlI start. During cloning. radio
(or transmitting displays - on LCD window. tr cloning is completed mmssfully. radio for
transmitting data displays SUCCESS message on LCD window. However. it certain error
occurs during cloning, radio displays ERROR massage.
Repeatedly. you can don the transmit data to other radios. To quit cloning mode. tum oft the
radio.
Busy Channel Lock 0uttBCLOJ
During certain channel in engaged. BCLO makes other radios not to transmit in that channel. There
are two types or CARRIER type and REFEATER type. In BARRIER type. transmitting is banned
when receiving channel is In busy. Contrarily. in REPEATER type. though the receiving channel is
in used. it the received CTCSSICDCSS signals are same as the programmed lnoso signals. it is
possible to transmit. With PC programmer. you can select one of 2 types or ignore.
4)
Power Saving Mode
it no received signal (receive stand-by) for ore-defined time, this radio goes into power saving
mode. Time value can be programmable try Pc programmer.
5)
Transmit time out and penalty time
mmmoosvmmc
rocnz 4"
W t 9907-09
General Infonnation
In order to prevent long-time transmission. transmit titne out feature can be used. When “me of
transmission exceeds the limitation. the radio is automatioelty switohed to receive mode. Further
more. penalty time. which makes the radio not to transmit tor pro-defined time period. can be
applied. Transmit time out and penalty time can be programmable by PC programmer.
6) DTMF transmisslon
Whenever you press the TX button. your radlo transmlts its own number of 4 dlglts mirth DTMF
signal. This funflion can be programmed by PC.
1.4.3 5 TONE CALL MODE
This is a mode to call party's identity by transmitting 5 kinds or tones in each digit. Al PRC-400
radlo have their own recelve number and it is possible to call normal or group call. As Pressing
inflation kathUN), press call switch(CAL) at a time, then the radio can be 5 tone mode and LCD
display like the following: '
l 3‘ Hall 0 non SEL
. .
SEL Indication at right top ot‘ LCD means 5 tone calling mode. No digits number displayed In
smal tont at tett ls memory number. 5 digits number in large lont represents pany‘s ID number
included in the memory. Accordingly, the above example shows a calling number.'12345‘ and
stored number.‘16‘. You can set and motify these numbers by Pc programmer or front panel key.
I) Swltch operations in 5 tone callan made
.selecting memory number : A v
. switching monitor ‘. MON switch
. callingtstand-by . CAL switch
. memorize call number : SCN switch [it
2) Switch operations in call number memory mode
. change number : A v
, Input changed number : MON switch {SET}
, quit memory mode : CAL switch [ESC]
. move prior aigit : SON switch [it
3) Ceiling procedure
a) Select a slored party‘s ID number by using A v snitch. Memory number without ID number
is displayed ‘-—-—' on LCD and than i! is not possible to call,
ti) Press monitor switch (MON) to go into the entry mode trom stand-by mode. LCD display 'CAL'
message.
momma-am SYSTENE, INC.
FCCID: ill
EXHIBIT 3: 99-07-09
General lniormalion
5) After continuing whether the channel is empty or not. press call switch {or transmitting. Ii
pressing call switch at stand-by mode. audiue alarm goes all and the radio goes into monitor
mode.
a) When channel is linked, operate as same way as a conventional radio. After communication
press call switch to go stand-by mode.
4) automatic reset
Alter switched to the entry mode. it there are no transmitting or receiving signals in a ore-defined
time period. the radio is changed automatically to the stand-by mode‘ Arr audible alarm goes oil for
about 5 seconds before the end of that time. You can set time for limitation by Pc programmer.
5) Busy channel roar outrecm)
Such as in the conventional mode. when certain channel is engaged. this leature restralns users
trom transmitting in that channel. User can select this feature by PC programmer.
6) ANI transmission [or 5 tone
Whenever you press the TX switch. your radio transmits its ANl number at 5 digits. It is possible to
select this feature or set ANI number by PC programmer.
7) Memonzing easing number procedure
a) Select the number of memory lor being stored or modified by using A v switch,
b) When press the scan switch. first digit is blinking. Then select desired number by using A v
switch. Alter 9“. character ‘A' means group.
o) When press the monitor snitch [SET]. second digit Is blinking. The selection or desired
number is as same as preceding method. Then press monflor glitch, It some mistake occurs
in prior digit. you can correct by scan switch [it].
it) When setting at 5 digit-number is done. the number is memorized in memory then calling
number memory mode Is complete.
e) In process at selling number, pressing CAL switch makes quitting calling number memory
mode and displaying prior number.
a) Group calling
Character ‘A’ in calling number means group. and Is representative of all number in 0~9 at that digit.
so.
1030A calls number from 10300 to 10309
10m cells number from 1030010 10399
A0305 calls 10 numbers. which have 0305 in the last 4 digits
(for example 00305,10305,20305...)
M305 calls 100 numbers. which have 305 In the IN 3 digits
(lo! example nososnoaos, 9930s...)
AMAA calls all numbers (00000 ~ 99999)
1.4.4 EEPROM PROGRAM VARIABLES
In this section. there is explanation for variables set by PC programmer. For more intormation ot
programming. please relor to the PC programmer user's manual.
1) Channel lrequencv and sIEp mm SYSTEM!
Poem: hammer-or Am
m" ’1 JEL 99-07-09
General lnlorrnation
You can set the lrequendes or steps of the channel number from 1 to 99. step value can be one or
4 step types (5K, 5.25K, 10K. 12.5K defined as channel).
2) Setting CTCSS/CDCSS
You can set CTCSS or CDCSS data in eatm channel. cross has 37 EIA standard codes and a
97.4l-lz code. Ana CDCSS has 83 Motorola compatible codes. Especially in 00088. positive and
negative codes can be selected. Each code is referred to lollowing frequency and code table.
3) Scan
a) Add scan channels
it is possible that the scan channels at receive frequency stored in your radio are added only.
b) Priority channel
Define and set one of assigned channels for scanning.
c) Seen types
i . carrier slcan : whenever the radio has valid traffic. it will halt scanning and pause on the active
channe .
ii . CTCSSIDCS scan : It thI halt scanning and pause on the channel when programmed Rx signal
is same as T: tone (CTCSSIDCS) signal.
at) Scan limar
Carrier scan period can be defined lrom Somsel: to QODmsec hy lmnseeand CTCSSICDCSS scan
period can be dellned tram 200mm: to names: by “mean.
o) Transmitting channel while scanning
You can select transmitting channel while scanning between the channel received last and channel
belore scanning.
l) User‘s Definition of Sean list and Priority channel
This [nature can be selected by switch operation on the front panel it wish.
4) Transmit time out and Penalty time
a} Transmit time out
can be set from Otto disable feature) to 255 seconds In a second step.
b) Penalty lime
can be set from Otto disable leaturc] to 255 seconds In a second step.
5) Time inlormallon ot power saving mode
a) Transmit lime out
can be not from one dis-aisle lecture) to 255 seconds In a second step. When the radio does
not receive any or signals for pro-defined time limitation. the radio goes into pwer saving
mode and alternates ON and OFF ol Rx power lorsaving power consumption.
b) Power-applying time
In power saving mode. power-applying time can be set from 10ms to seems in a lums step.
c) Power-cute” time
In power saving mode. power-cutoff time can be set from 10rns lo ”Orr-S in a toms step.
5) “WP "3 ‘"’°"“‘“““ AERUI'RON-RE'OO SYSTEMS, me.
a) Selection transmit mode lcr DTMF ID FCC ID: NGIUHFHH-Ol
Vuu can select transmit mode for DTMF ID or not. EXHIBIT t 4L
h) Setting DTMF ID
These are two types of conventional and Kukjae type you can select. In conventional type. you can
99-07-09
General information
set 4 digits by using to numbers (0-9) and 8 characters (A.B.C.D.‘.#). And you an set 5 dlglts
lrom ooooo to 20915 in Kukjae type.
c) LEAD-IN new time
This feature can be selected for transmitting and receiving exacuy. This time is defined from Oms
2550ms in a toms step.
d) UTMF time type
Can set the time of OTMF tone and pause time lrom «ms to afiOOmS in lmS step.
7) Busy channel loclt oul(BCLO)
Gan select one of Garner type. Repeat type or not.
3) Menitorfeeture
can select MMIO' function or not.
9) Stone selective calling
Can select 5 tone selective calling feature or not.
1.4.5 EEPROM VARIABLES IN 5 TONE CALLING MODE
1) Setting lone type
Besifles 8 standard tones. you can set user-defined lone type.
2) Setting ID number
Can store party's ID number to memory number trom 1 to 99. Also. user can store this memory
region by snitch ot the radio.
3] Setting tone length
Length of all Stones can be set lrom zoms to tzooms In 3 ms step.
it LEAD-IN DELAY time belore 5 tone calling
can be set lrom ems lo 2550ms in a turns step.
5) 5 Tone AM!
can soled 5 Tone ANI mode or not. User can select between user‘s own receiving number and
certain number.
6) LEAD-IN DELAY Ilme belore 5 lane ANI
This feature can be set from we to 2550ms in a toms step,
7) Setting own receive number
can be set rmn receive number 0! radio.
8) Busy channel lock oul(BcLO)
When receive channel is engaged. user can inhibit from calling and transmitting.
9) Automatic reset
Can be set from 1ms to 255ms in 1ms step. mm m M
FCC ID: MOWER)!
mourn: fl]:
99-07-09
General lnlormaiion
1.4.6 MCU PORT TABLE
Circuit
Operalion
lI---W
Emma-m Fmscmw
PLL LATCH ENABLE
PLI. LE
(DATA LATCH IN RISING EDGE)
nm—_nn
“mun—
Elm—ml:-
we MUTE (MUTE IN Rx. DTMF
7 ID AND 5 TONE
msmssmm
AMP MUT “n AUDIO AMP MUTE
. Rx POWER on
RF men-4 POWER SELECT
(IN '|.'. HIGH POWER OUTPUT}
VLcoa - LCD Bus 3
m -—
n-—--—
n-
nm
18
19 “08C?
”7 (REPEAT ONIOFF m POWER
SAVING MODE)
n Tx POWER on
RF POWER ENABLE
(ENABLE AFTER Pu. LOCK N
TX)
il gflflfi
99-07-09
Genetal Momafion
DAO H
“mm“ WWW,
ummn_
nmmn_
ammu-
Im_fl-W
u- PLL LD -- PLI. LOCK DETECT INPUT
FUNCTION SWITCH
Opamflon
- CONNECT T0 4MHZ CRYSTAL
- CONNECT T0 AMHZ CRYSTAL
DIA CONVERTER 0
PTT SWITCH
CHANNEL UP SWITCH
CHANNEL DOWN SWITCH
LCD LAMP SWITCH
SQUELCH DETECT
SCAN SWITCH
MONITOR SWITCH
”D
lHHEHEEHE
‘o
21
87 CALL SM] CALI. SWITCH
SERIAL DATA INPUT
(Fxsosmzsmo)
SERIAL DATA OUTPUT
40
(FXSDSIXZSI BOIPLI.)
mow-am SYSTEMS. INC
POCID: ill
EXHIBITO:
59-07-09
Generannfmmafion
Ref. Circun
Type
NO‘ Sign
SERIAL CLOCK OUTPUT
(FXBDEIXZEHSOIPLL)
HI-II
nm-m mm“
mm n-
um Illl
Emmi“: mm
n-I-m
-- Lcmwmmm
LCD COMMON SEGMENT 2
LCD COMMON SEGMENT 1
LCD COMMON SEGMENT 0
LCD SEGMENT 0
LCD SEGMENT I
LCD SEGMENT 2
LCD SEGMENT 3
LCD SEGMENT 4
LCD SEGMENT 5
LCD SEGMENT a
LCD SEGMENT 7
99-07-09
General Inflammation
Rel. Circuit
Type
NO. Sign
fl
- LCD SEGMENT B
-n-
“— LCDSEGMENT13
oz
- LCD SEGMENT 15
LCD SEGMENT 17
an
LCD SEGMENT 13
LCD SEGMENT 19
LCD SEGMENT 20
q u v4 ~4 -.| 4 -.4
E!!- !“ Hun-Inn'nn
L4
-|
macs “- xz51GDCHIPSELECT
mmonmroo svstms mc.
rec nz mammal-01
mm a
99-07-09
General lnlormallon
1.4.7 OPERATION PROCEDURE
1)
2)
3)
4)
5)
G}
7)
5)
9)
Remave the enver no: and make sure equipments configurations and enamel lasture.
Check to charge the battery paek fuIy.
Screw and insert the small whip anlenna in the lap of yeur radin,
It the volume swileh turn the duckwise direelion (CW). turn on radio power.
Press and hold ltle monitor switch [MON] fora seconds. Then watch receive lamp lighting on.
Sel the volume level as turning the much cw or 00W. And set squelch volume switch turn to
CW, until the white noise doesn‘t go off.
Press the maniler snitch again.
Press and hold the PTT snitch and make sure of hearing Milan-on signal and lighting on the
TX lamp.
Finally. check the empty channel and slant the radio operallon.
mm
locum Wine.
m1? 0:
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Modify Date : 1999:09:23 16:55:43 Creator : Photoshop PDF Plug-in 1.0 Producer : Photoshop PDF Plug-in 1.0 Create Date : 1999:09:23 16:55:04 Page Count : 12EXIF Metadata provided by EXIF.tools