Agri Fab 45 0362 User Manual 42 ROUGH CUT TRAIL MOWER Manuals And Guides L0406294
AGRI-FAB Mower Deck Manual L0406294 AGRI-FAB Mower Deck Owner's Manual, AGRI-FAB Mower Deck installation guides
User Manual: Agri-Fab 45-0362 45-0362 AGRI-FAB 42 ROUGH CUT TRAIL MOWER - Manuals and Guides View the owners manual for your AGRI-FAB 42 ROUGH CUT TRAIL MOWER #450362. Home:Lawn & Garden Parts:Agri-Fab Parts:Agri-Fab 42 ROUGH CUT TRAIL MOWER Manual
Open the PDF directly: View PDF .
Page Count: 28
Download | |
Open PDF In Browser | View PDF |
Agri-Fab ® OWNERS MANUAL Model No. 45-0362 42" ROUGH CUT TRAILMOWER CAUTION: Read Rules for Safe Operation and Instructions Carefully _/,/_'_'u_'rdr/ PRINTED IN U.S.A. NOTE: Your mower deck will require a 12 volt battery to operate. This battery is NOT included with the deck but must be purchased separately. Any 12 volt tractor battery with about 230 cold cranking amps. will operate the machine. • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts www.speedepart.corn FORM NO. 49202 (3/04) TABLE OF CONTENTS SAFETY RULES ...................................................... SAFETY AND OPERATIONAL HARDWARE ASSEMBLY DECALS ................ 5,6 CHART .................................................. ............................................................ OPERATION ......................................................... CUSTOMER RESPONSIBILITIES REPAIR PARTS ................................................... DIAGRAM ................................................... 2 7 8-11 12-16 ...................... 17-20 STORAGE ................................................................. WIRING 3,4 21 22-26 27 SAFETY RULES Safe Operation Practices for Tow Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Im • • • • • • • • • • • • • • GENERAL OPERATION II. Read, understand, and follow all instructions in the manual and on the machine before starting. Read this operator's manual carefully. Become familiar with the controls and know how to operate your mower properly. Only allow responsible adults, who are familiar with the instructions, to operate the machine, Clear the area of objects such as rocks, toys, wire, etc., which could he picked up and thrown by the blade. Be sure the ares is clear of other people before mowing. Stop machine if anyone enters the ares. Never carry passengers. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Slow down before tuming. Never leave • running machine unattended. Always turn off blades_ and stop engine. Turn off blades when not mowing. Mow only in daylight or good artificial light. Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Usa extra care when loading or unloading the machine into a trailer or truck. Slopes are a major factor related to bes-of-control and tipover accidents, which can result in severe injury or death. All slopes require extra caution. If you feel uneasy on it, do not mow if. DO: • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obatacles. • Use slow speed. Choose a low gear so that you wil! not have to stop or shift while on the slops. Follow the tractor manufacturer's recommendations for • wheel weights or counterweights Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. • Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. DO NOT: • Do not mow near drep-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. Exercise special care when mowing around fixed objects in order to prevent the blades from striking them. Never deliberately run tractor or mower onto or over any foreign object. Usa mower only as the manufacturer intended and as described in this manual. • Do not mow on wet grass. Reduced traction could cause sliding. Do not operate mower if it has been dropped or damaged in any manner. Always have damage repaired before using your mower. Always wear safety glasses or eye shields when starting and while using your mower. Dress properly. Do not operate mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing. Always make cutting height adjustments before starting your mower. Never attempt to do this while the engine is running. Keep your eyes and mind on your mower and the area being cut. Do not let other interests distract you. Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. Before cleaning, inspecting, or repairing your mower, stop the engine and make absolutely sure the blade and all moving parts have stopped. Then disconnect the spark plug wire and keep it away from the spark plug to prevent accidental starting. Do not operate your mower if it vibrates abnormally. Excessive vibrationis an indicationof damage or unbalanced blades. Stop the engine,safety check for the cause of the vibrationand repair as required. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Disengage power to mower, stop engine when transporting or not in USa, • • • • • • • • • to improve stability. • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. Do not attempt to operate your tractor or mower when not in drivers seat. • Mow up and down slopes, not across. • • • • SLOPE OPERATION III. Never operate your mower withoot proper guards, plates, or other s_ety devices in place. 3 CHILDREN • Keep children out of the mowing area and under the watchful care of another responsible adult. • Be alert and turn machine off if children enter the area. • Before and when becking, look behind and down for small children. • Never carry children. They may fall off and be sanously injured or interfere with safe machine operation. • Never allow children to operate the machine. • Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision. IV. SERVICE Look for this symbol to point out important safety precautions. It means CAUTIONlll BECOME ALERTlll YOUR SAFETY IS INVOLVED. Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive, Use only an approved container. -Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke. Never refuel the machine indoors. Never store the machine or fuel container inside where there • is an open flame, such as a water heater. Never run a machine inside a closed area. • Keep nuts and belts, especially blade attachment nuts, tight and keep equipment in good condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up, Clean oil or fuel spillage. Allow machine to cool before storing. • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Never make adjustments or repairs with the engine running. • Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. Adjust and service as required. 4 SAFETY Replace number. II AND OPERATIONAL decal immediately See back cover. KEEPHANDSandFEETAWAY if damaged. DECALS Order by part 11 ROTATING BLADES AND BELTS. KEEP ALL SHIELDS IN PLACE. KEEP HANDS AND FEET FROM UNDER MOWER. HA12314 HA12315 DANGER ROTATING BLADES DECAL DANGER DECAL F HOW TO USE YOUR MOWER STOPPING • Move mower blade clutch lever to "DISENGAGED" position. • Move throttle control to "SLOW" position. • Turn ignition key to "OFF" position. CAUTION STARTING OWNERS MANUAL I READ AND FOLLOW DIRECTIONS IN KNOW HOW TO OPERATE BOTH THE VEHICLE AND THE MOWER ATTACHMENT • Move mower blade clutch lever to "DISENGAGED" position. • Move throttle control to the choke position for cold engine starts. • Turn ignition key clockwise to "START' position and release key as soon as engine starts. • When engine starts, slowly move throttle control to "FAST" position. • Allow engine to warm up. NEVER ALLOW CHILDREN TO USE THE EQUIPMENT DO NOT LEAVE MOWER RUNNING WITH UNIT UNATTENDED KEEP ALL SAFETY FEATURES IN PLACE AND OPERATING USE • Sit on tractor seat. • Move mower blade clutch lever to "ENGAGED" position. • Operate tractor at medium ground speed. (3-4 MPH) AVOID CONTACT WITH MOVING PART. KEEP HANDS AND FEET AWAY FROM BLADES STOP ENGINE BEFORE FUELING,ADJUSTING OR INSPECTING. DO NOT ADD FUEL TO AN ENGINE THAT IS RUNNING OR HOT TRANSPORTING • Shut off engine. • Place mower deck in the highest position directly behind tractor. HA24431 5 SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number. See back cover. BLADES ENGAGED \ BLADES DISENGAGED BLADE CLUTCH LEVER HA23265 CLUTCH LEVER OPERATION DECAL THROTTLE _ CHOKE ® © SLOW HA23820 .................... 6 J CONTENTS SHOWN OF PARTS BAG FULL SIZE f B j NOT SHOWN K FULL SIZE I f I I I M N J I f J I I J I J J REF. A B C D E F G QTY. 1 2 2 2 3 2 1 DESCRIPTION Hex Bolt, 1/2" x 7" Hex Bolt, 1/4" x 7-1/2" Hex Bolt, 3/8" x 2-3/4" Hex Bolt, 5/16" x 3/4" Hex Bolt, 1/4" x 3/4" Screw, Self Tapping #10 x 1/2" Hex Lock Nut, 1/2" REF. H I J K L M N 0 7 QTY. 2 2 1 2 2 2 2 1 DESCRIPTION Hex Lock Nut, 3/8" Hex Lock Nut, 5/16" Hex Lock Nut, 1/4" Hex Nut (SEMS), 1/4" Flat Washer, 3/8" Clip, 3/8" Plastic Nut Key O ASSEMBLY TOOLS (1) (2) (2) (2) (2) REQUIRED FOR ASSEMBLY INSTALL 5/16" Wrench 7/16" Wrenches 1/2" Wrenches 9/16" Wrenches 3/4" Wrenches or Adjustable Wrenches • • • • CLUTCH TO TOWBAR TUBE Place Clutch Cable forward along Towbar Tube. Spread ends of two Cable Clips and place around Clutch Cable. Place Clutch Cable on top of Towbar Tube and align Cable Clips with bolt holes in Towbar Tube. Secure with two #10 Screws. UNPACKING INSTALL Enclosed in packing crate are (3) items: 1. Mower Deck 2. Tow Bar Hitch Assembly 3. Box of Parts consisting of: • Rear Roller • Rear Roller Bracket • Your Trail Mower requires a 12 volt battery to operate. The battery is NOT included with the unit. It must be purchased separately. • Remove four screws and the Battery Cover from the Mower and set them aside. Bag of Parts (See page 7) • • ENGINE OIL VERY IMPORTANT: Engine must be filled with oil before operation. See OIL & FUEL RECOMMENDATIONS in engine Owner's Manual for correct filling instructions and oil fill capacity. INSTALL TOWBAR QUADRANT • • • • • • • • TUBE BATTERY TO REAR • • Place the Battery Hold Down on top of the Battery. Secure the Battery to the Mower Deck with two 1/4 x 7-1/2 hex bolts. • Open the terminal Hold Down. • Connect the Red Wire to the positive (+) battery terminal using a 1/4 x 3/4 hex bolt and 1/4 SEMS nut. Tighten securely. Connect the Black Wire to the negative (-) battery terminal using a 1/4 x 3/4 hex bolt and 1/4 SEMS nut. Tighten securely. Close the terminal access doors. • • Remove Hex Bolts and lift Front Drive Cover from mower housing. Rest end of Tow Bar Tube on front edge of mower. Feed Wire Harness in end of Tow Bar Tube through large hole in back wall of Rear Quadrant. Place Towbar Tube into Rear Quadrant, align holes and insert 3/8 x 2-3/4 Hex Bolt through quadrant and rear hole of Tube. Install two Plastic Nuts into the square holes in the Mower Deck under the Battery Cover. Place the Battery on the Mower Deck between the two Plastic Nuts. • Replace screws. INSTALL LEVER • Secure tightly with 3/8 Hex Lock Nut and then loosen 1/4 turn to allow Tube to pivot freely inside Rear Quadrant. Assemble a 3/8 Flat Washer onto a 3/8 x 2-3/4 Hex Bolt. Insert Bolt and Washer into slot in Rear Quadrant and into hole in Towbar Tube. • • • Secure Tightly with 3/8 Flat Washer and 3/8 Hex Lock Nut, then loosen 1/4 turn to allow Tube to pivot freely inside Rear Quadrant. • NOTE: Towbar Tube must pivot freely inside Rear Quadrant when Latch is pulled from notch. 8 access doors on the Battery Battery Cover and secure it with the four CLUTCH CABLE TO CLUTCH Remove outer 5/16 Nut from end of Clutch Cable Housing. (See Fig. 1) Turn inner 5/16 Nut to bottom of thread. Insert Cable and outer 5/16 Nut through slotted hole in Cable Guide of Hitch Assembly. The outer 5/16 Nut must be cocked sideways to insert through slotted hole of Cable Guide. Reinstall outer 5/16 Nut to the cable housing to secure Cable Harness to Cable Guide. Install Mounting Anchor of Clutch Cable to Clutch Lever using 1/4 x 3/4 Hex Bolt and 1/4 Lock Nut. Tighten 1/4 Lock Nut securely and then loosen approximately two turns to allow Mounting Anchor to pivot freely on bolt. ASSEMBLY TERMINAL ACCESS DOORS 1/4 X 3/4 HEX BOLT & BATTERY COVER 1/4 HEX NUT (SEMS) N BLACK WIRE SCREW (4) BATTERY HOLD DOWN 1/4 X 7-1/2 HEX BOLT PLASTIC NUT RED WIRE 1/4 X 7-1/2 HEX BOLT 3/8 X 2-3/4 HEX BOLT CLUTCH LEVER 3/8 FLAT WASHER #10 SCREW (2) CABLE CLIP (2) .3/8 FLAT WASHER V 3/8 HEX LOCK NUT 1/4 X 3/4 HEX BOLT CLUTCH CABLE 5/16 HEX NUT (2) FIG. 1 MOUNTING ANCHOR 9 1/4" HEX LOCK NUT ASSEMBLY INNER NUT CLUTCH CABLE ADJUSTMENT / / • • • / / Remove four screws from Rear Drive Cover. Lay aside cover and screws. / / / OUTER NUT Place Clutch Lever in "DISENGAGED" position The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" • • • SWITCHE] BODY position. Loosen the outer nut on the Clutch Cable. Tighten the inner nut on the Clutch Cable. Repeat the above procedure until you have the correct tension. o © \ \ \ \\ IDLERE] PULLEY ENC PULLEY PLUNGER BLADEE] ILLEY CLUTCH LEVER FOURE] SCREWS CLUTCH LEVER FIG. 2 10 ASSEMBLY INSTALL • • • REAR ROLLER TO DECK Install Rear Roller Mounting Bracket to rear of deck using two 5/16 x 3/4 Hex Bolts and two 5/16 Hex Lock Nuts. (See Fig. 3.) Install Roller to Rear Roller Bracket using 1/2 x 7 Hex Bolt and 1/2 Hex Lock Nut. Make sure Roller turns freely on Bolt. 5/16 X 3/4 HEX BOLTSB AND 5/16 HEX LOCK NUTS "h ROLLER 1/2 X 7 HEX BOLT REAR ROLLERB MOUNTING BRACKET 1/2 HEX LOCK NUT FIG. 3 11 OPERATION KNOW YOUR MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR MOWER. Compare the illustrations with your mower to familiarize yourself with the location of various controls and adjustments. Save the manual for future reference. HEIGHT ADJUSTMENT MOWER BLADE CLUTCH LEVER STRAP IGNITION KEY SWITCH HEIGHT ADJUSTMENT LIFT LEVER TOW HITCH OFFSET ADJUSTMENT 3HT ADJUSTMENT STRAP TOW BAR HEIGHT ADJUSTMENT THROTTLE CONTROL FIG. 4 MOWER BLADE CLUTCH LEVER - Starts and stops mower blade rotation. THROTTLE CONTROL - Controls engine speed, engine shut-off and engine choke. IGNITION KEY SWITCH - Used to start and stop engine. HEIGHT ADJUSTMENT LIFT LEVER - Raise and lower mower to different cutting heights. HEIGHT ADJUSTMENT STRAP - Controls cutting height, TOW BAR HEIGHT ADJUSTMENT - To level mower front to rear. TOW HITCH OFFSET ADJUSTMENT - To adjust mower deck offset from tractor center. 12 OPERATION The operation of any mower can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your mower and while mowing. We recommend wide vision safety mask for over the spectacles or standard safety glasses. CHILDREN ,_ Tragic occur if not the alert to the presence of children. Childrenaccidents are often can attracted to the the operator machine isand mowing activity. Never assume that children will remain where you last saw them. HOW TO USE YOUR ATTACHING MOWER STOPPING • MOWER BLADES- • • Move mower blade clutch switch to "DISENGAGED" position. • ENGINE• • MOWER TO TRACTOR Place mower behind tractor and back tractor up to it for attaching. (See Fig. 5) Slide tow bar of mower over tractor draw bar so that the hitch pin holes line up. Insert hitch pin until it extends through the bottom of the tow bar. Insert hair cotter pin through hitch pin. Move throttle control to "SLOW" position. NOTE: Failure to move throttle control to "SLOW" position or allowing engine to idle before stopping may cause engine to "backfire". • • Turn ignition key to "OFF" position and remove key. Always remove key when leaving tractor to prevent unauthorized use. Never use choke to stop engine. TO USE CHOKE CONTROL TRACTOF HITCH PIN OR MOWER CLEVIS PIN Use choke control whenever you are starting a cold engine. Do not use to start a warm engine. • • • To engage choke control, move throttle control to choke position. After engine has started move throttle control to full throttle position. TO USE THROTTLE HAIR COTTER PIN FIG. 5 CONTROL Always operate engine at full throttle. • • Operating engine at less than full throttle reduces the battery charging rate. Full throttle offers the best mower performance. TRANSPORTING • • TRACTOR DRAWBAR Shut off engine. Place mower deck in the highest position directly behind tractor. 13 OPERATION BEFORE STARTING ENGINE • Fill engine with oil. (See engine manual for proper procedure and requirements. • Add gasoline. Fill fuel tank using fresh clean unleaded gasoline. (See tractor manual for safe filling procedure and storage instructions) STARTING • • • • TO START Adjust mower cutting height. Start mower engine. Move throttle to fast position. Move mower blade lever to"ENGAGED" BREAKING CAUTION: FILL TO BOTTOM OF FUEL TANK FILLER NECK. DO NOT OVERFILL. WIPE OFF ANY SPILLED OIL OR FUEL. DO NOT STORE, SPILL OR USE GASOLINE NEAR OPEN FLAME. ENGINE MOWING • • • ,_ PROCEDURES NEVER CARRY CHILDREN. THEY MAY FALL OFF AND BE SERIOUSLY INJURED CAUTION: OR INTERFERE WITH SAFE OPERATION Mowing should be started with tow vehicle in low gear and speed increased only as mowing conditions will safely permit. Mower will perform at its best when engine throttle is set for full throttle. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32°F), the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in your Engine Owner's Manual Always operate mower engine at full throttle when mowing to assure better mowing performance and proper discharge of matedal. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired. When operating any attachment select a ground speed that will suit the terrain and give best performance of the attachment being used. CAUTION: ,_ MOWER CAUTION: TRAGIC ACCIDENTS CAN OCCUR IF THE OPERATOR IS NOT ALERT TO THE PRESENCE OF CHILDREN. CHILDREN ARE OFTEN ATTRACTED TO THE MACHINE AND THE MOWING ACTIVITY. NEVER ASSUME THAT CHILDREN WILL REMAIN WHERE YOU LAST SAW THEM. Move mower blade clutch lever to"DISENGAGED" position. Move throttle control to the choke position for cold engine starts. For warm engine starts move throttle control to midway between "FAST" and "SLOW" positions. Turn ignition key clockwise to "START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If engine does not start after several attempts, move throttle control to "FAST" position, wait a few minutes and try again. When engine starts, slowly move throttle control to "FAST" position. Allow engine to warm up for a few minutes before engaging mower blade clutch lever. • IN YOUR position. Break in your belts, pulleys, and engine before you actually begin mowing. • Start engine, engage blade control to start blades rotating and allow blades to rotate for approximately five minutes to break in mower and engine. When starting engine for the first time or if engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • THE MOWER MOWER FOR ANY OBJECTS THAT COULD CHECK AREA FROM UNDERUNDER AND AROUND BE THROWN MOWER. MAKE SURE THAT MOWER DISCHARGE AREA IS CLEAR. IMPORTANT: Avoid prolonged mowing of ditches with slopes greater than 15 degrees. Small engines become starved for oil at angles greater than 15 degrees and should only be used for brief periods on such slopes. Be sure the engine is filled to the maximum oil level when mowing on slopes. 14 OPERATION MOWER HEIGHT ADJUSTMENT FRONT CAUTION: SHUT OFF MOWER ENGINE AND REMOVE _ To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/4" to 3/4" lower than the rear. To check front to back adjustment measure from the bottom edge of the deck to the ground at both front and rear of the deck. PARK PLUG WIREANY FROM SPARK PLUGTO BEFORE MAKING ADJUSTMENTS THE MOWER TO ADJUST MOWER FROM FRONT TO BACK The cutting height range is approximately 1-1/2 to 5 inches. The heights are measured form the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of brush and types of brush being mowed. CUTTING • • • • • • HEIGHT TO BACK RAKE ADJUSTMENT • • • • ADJUSTMENTS Remove two hair cotter pins from two clevis pins in the tow bar adjustment. (See Fig. 6) Remove two clevis pins from tow bar adjustment. Raise or lower the tow bar to obtain the proper front to back adjustment. Reassemble two clevis pins to tow bar adjustment and secure with two hair cotter pins. To adjust the mower cutting height remove hair cotter pin from locating pin. (See Fig. 6) Apply down pressure to height adjustment lift lever. Remove the locating pin from the height adjustment strap. Move height adjustment strap up or down to align it with the desired hole in the height adjustment strap. Reassemble locating pin to the height adjustment strap and secure with hair cotter pin. Make sure that both side height adjustment straps are adjusted to the same height. HAIR COTTER PIN LOCATING PIN HEIGHT ADJUSTMENT _'_ STRAP HEIGHT ADJUSTMENT CUTTING HEIGHTS GROUND LEVEL / CUTTING HEIGHT --1_- FIG. 6 15 OPERATION TOW HITCH OFFSET ADJUSTMENT CAUTION: SHUT OFF MOWER ENGINE AND REMOVE This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow vehicle while cutting down the brush beside him. The adjustable hitch gives you three offset cutting positions plus straight behind for narrow paths. _lb PARK PLUG WIREANY FROM SPARK PLUGTO BEFORE MAKING ADJUSTMENTS THE MOWER TO ADJUST THE OFFSET HITCH • Pull back the pivot latch from the notch of the front quadrant. Adjust the hitch tube to the desired offset and release the pivot latch into the notch of the quadrant. (See Fig. 8) • Pull back the pivot latch from the notch of the rear quadrant. Adjust the hitch tube to the corresponding notch of the front quadrant and release the pivot latch into the notch. IMPORTANT: The hitch tube must be assembled to the same offset notch in both the front and rear MODEL 45-0362 The adjustable hitch of this mower can be set in seven positions including straight and offsets of 9", 17" and 23" on both sides. (See Fig. 7) quadrants. 9" OFFSET ON MODEL 45-0362 OFFSET _17,, OFFSET ON MODEL 45-0362 I _) OFFSET _/ ATCH 23"OFFSET LATCH 17" OFFSE'I , II- JO;_ 9 _ STRAIGH1 _ 23" OFFSET ON MODEL 45-0362 /° REARQUADRANT FIG. 7 FIG. 8 16 CUSTOMER GENERAL RESPONSIBILITIES RECOMMENDATIONS Once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. The warranty on this Vehicle does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. BEFORE EACH USE Some adjustments will need to be made periodically to properly maintain your unit. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • • • Check engine oil level. Check blade operation Check for loose fasteners. LUBRICATION Keep unit well lubricated (See "LUBRICATION CHART"). MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE Change Engine Oil DATES I1_ Inspect Spark Arrester Muffler Inspect Air Screen V/ Check and Clean Air Cleaner II_ Replace Air Cleaner Cartridge Clean Engine Cylinder Fins Replace Spark Plug [ Lubricate Spindle 1 - Change I1_ more often when operating unaer a heavy load or in high ambient temperatures, LUBRICATION CHART 2- Service more often when operating in dirty or dusty conditions. WHEEL PIVOT _3_ SPINDLE _2_ O REFER TO ENGINE MANUAL Q GENERAL PURPOSE GREASE @ DRY LUBRICANT WHEEL_2),_ IMPORTANT: DO NOT OIL OR GREASE PIVOT POINTS. VISCOUS LUBRICANTS WILL A'R'RACT DUST AND DIRT THAT CAN CAUSE WEAR ON PIVOT POINTS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY POWERED GRAPHITE TYPE LUBRICANTS. SWIVEL_2_' QUADRANT _3) 17 WHEEL PIVOT _3_ CUSTOMER BLADE RESPONSIBILITIES CARE AND SERVICE BLADE ASSEMBLY CAUTION: BARE HANDS. CARELESS OR IMPROPER DO NOT HANDLE MOWER BLADES WITH HANDLING MAY RESULT IN SERIOUS INJURY. BLADE CARE For best results mower blades must be kept sharp. The blades can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen blades while they are still on the mower. BLADE SERVICE (Refer to fig. 9) TO • • • REMOVE BLADE ASSEMBLY FROM DECK Remove cotter pin from the spindle shaft. Remove nut and washer from the spindle shaft. Pull blade assembly off the spindle shaft. (Watch for a key in the spindle shaft.) TO • • • REMOVE BLADES FROM BLADE ASSEMBLY. Remove cotter pin from the blade bolt. Remove nut from the blade bolt. Remove blade from the blade assembly. FIG. 9 WARNING: SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS OR REPAIRS TO THE MOWER. BLADE SHARPENING • Blades can be sharpened with a file or grinding wheel. NOTE: When sharpening blades take care to maintain blade balance. Sharpen both blades equally even if one blade does not need to be sharpened. Check balance by weighing each blade to make sure they are equal in weight. CLEANING Water pressure from a garden hose will remove fresh clippings from the underside of the mower. Clean mower after each mowing. CAUTION: ,_ DALLY MAINTENANCE IFYOUR BLADE SHOWWEAR, REPLACE THEM BOLTS WITH FACTORY REPLACEMENTS ONLY. Make sure all nuts and bolts are tight, cotter pins and retainer springs are secure. Keep blades sharp. Observe all Safety Precautions. Keep mower well lubricated. TO REINSTALL BLADES • Assemble a blade bolt through a flat washer, a blade and then another flat washer. • Assemble the bolt through the hole in the stump plate and the blade hub assembly. • Assemble a flat washer and nut onto the blade bolt. • Tighten nut, then loosen just until blade can pivot. • Install a cotter pin to secure the nut. TO • • • • THE MOWER REPAIR PARTS Your rotary mower has been produced with components designed for your unit. Although standard V-belts, bearings, blades, pulleys, etc. may look like parts used on your rotary mower, while similar in appearance many are of a different construction and could in some cases cause a malfunction in the operation of the machine. REINSTALL BLADE ASSEMBLY TO MOWER Reinstall key in spindle shaft, if necessary. Install the blade assembly onto the spindle shaft. Secure with flat washer and nut. Torque the spindle shaft and nut to 15 FT. LBS. and secure with a hair cotter pin. For continued satisfactory performance use only repair parts supplied by the manufacturer. See the dealer where the mower was purchased for factory replacement parts. 18 CUSTOMER RESPONSIBILITIES INNER NUT CLUTCH CABLE ADJUSTMENT / • \ \ , \ OUTER NUT Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" SWITCHD BODY position. • Loosen the outer nut on the Clutch Cable. • Tighten the inner nut on the Clutch Cable. • Repeat the above procedure until you have the correct tension. © 1/8"" © IDLERD PULLEY ENC PULLEY PLUNGER BLADED PULLEY CLUTCH LEVER 19 o CUSTOMER RESPONSIBILITIES INSTALLING NEW V-BELT V-BELT REPLACEMENT • • V-belt must be replaced if it becomes stretched to the point that it can no longer be adjusted, or if it becomes frayed or otherwise can not function properly. Move Blade Clutch Lever to the "DISENGAGED" position. • • • • I,_ DISCONNECT CAUTION: SPARK PLUG WIRE • • REMOVING OLD V-BELT • Remove Rear Drive Cover. • Remove Front Drive Cover. • Remove Hair Pin and Clevis Pin from Clutch Cable. • Loosen two Rear Belt Guides and pivot them away from Blade Pulley. • Remove V-belt from around Blade Pulley. • Remove one small Hair Pin from Belt Keeper Rod and slide Belt Keeper Rod to the side. • Pull V-belt down from around Engine Pulley and remove V-belt from Mower. • • Feed new V-belt between the two belt guides at the Engine Pulley. Place V-belt up and around the Engine Pulley. Check to make sure the V-belt is seated properly in the groove of the Engine Pulley. Place V-belt along inside of Idler Pulley. Wrap V-belt down around Blade Pulley, placing Belt inside of Rear Belt Guides. Reinstall V-belt Keeper Rod and secure with Small Hair Pin. Check to make sure V-belt is over top of Keeper Rod. Reposition and retighten two Rear Belt Guides at the rear of the Blade Pulley. Leave approximately 1/16" between Guides and Pulley. Reinstall Clevis Pin and Hair Pin into Clutch Cable. Reinstall Front Drive Cover and Rear Drive Cover. BELT GUIDES HAIRPIN AND CLEVIS PIN BLADE PULLEY REAR BELT GUIDES ENGINE PULLEY BELT KEEPER ROD V-BELT 20 STORAGE Immediately prepare your mower for storage at the end of the season or if the unit will not be used for 30 days or more. ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil. (See engine manual) MOWER CYLINDER When the mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean dry area. • Clean entire mower (See =CLEANING") • Lubricate as shown in the Customer Responsibilities section of this manual. • Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. • Touch up all rusted or chipped paint surfaces; sand lightly before painting. • • • • OTHER • • Do not store gasoline from one season to another. Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. • If possible, store your unit indoors and cover it to give protection from dust and dirt. • Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust. IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND EXHAUST ARE STILL WARM. CLEANING IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP BRUSH AND TRASH. CLEAN THE UNDERSIDE OF YOUR MOWER AFTER EACH USE. CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with the spark plug. • • • Remove spark plug. Pour one ounce (29 ml) of oil through spark plug hole into cylinder. Pull starter handle slowly a few times to distribute oil. Replace with new spark plug. CAUTION: Clean the underside of your mower by scraping to remove build-up of brush and trash. Keep finished surfaces and wheels free of all gasoline, oil, etc. We do not recommend using a garden hose to clean mower unless the electrical system, muffler, air filter, and carburetor are covered to keep water out. Water in engine can result in shortening engine life. Never store the mower with where fumes may an aopen flame or gasoline in the tankreach inside building spark. Allow the engine to cool before storing in any enclosure. ENGINE • Never use engine or carburetor cleaner products in the fuel tank or Permanent damage may occur. • Use fresh fuel every season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer. 21 42" ROUGH CUT TRAILMOWER - MODEL 45-0362 o © 22 42" ROUGH CUT TRAILMOWER - MODEL 45-0362 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 1. HA24255 MOWER DECK 48. HAl15321 SCREW 5/16-18 X 5/16 SOC. SET 2. 3. HA24378 HA23193 GUARD WHEEL 50. 43555 WASHER 7/16" LOCK SCREW 3/8-16 X 1-1/4 THD. FORMING 51. HA181668 BOLT 7/16-20 X 1-1/4 HEX HEAD 4. HA24292 BRACKET 52. 25051 COVER, GAS TANK 5. HA24293 ROD BELT GUIDE 53. 25265 6. HA3090 PIN HAIR COTTER 55. 43182 COVER, FRONT DRIVE BOLT 5/16-18 X 3/4 HEX HEAD 7. HA24294 8. HA24295 V-BELT (B SEC. 60" O.C.) CHANNEL CLUTCH LEVER 56. 57. 43064 25264 9. 45100 BOLT 1/2-13 X 4" HEX HEAD 58. HA23732 COVER, REAR DRIVE TANK GASOLINE 10. HA120396 WASHER 1/2 FLAT 59. HA24317 PLATE FUEL TANK 11. 43262 NUT 1/2-13 HEX LOCK 60. HA163318 SCREW 1/4-14 X 7/8 TAPPING PAN HEAD 12. HA14232 WASHER FLAT 61. HA23733 CAP GASOLINE 13. HA24296 ROD CLUTCH LINK 62. 48837 HOSE FUEL TANK LONG 14. 44101 43081 63. 64. HA24455 HA23792 HOSE FUEL TANK SHORT 15. PIN, COTTER 3/32" X 3/4" WASHER FLAT 5/16" STD. WRT. CLAMP FUEL LINE 16. HA24297 SPRING CLUTCH 65. HA23791 FILTER FUEL LINE 17. 49165 CLUTCH CABLE ASSY 66. 48095 PIPE BELT GUIDE NUT 5/16-18 HEX LOCK TANK STRAP, CLUTCH ADJUSTING 67. 48096 CAP 68. 69. HA24310 HA12138 BRACKET 43016 BOLT, 1/4-20 X 1" HEX HEAD NUT 1/4-20 HEX LOCK 21. 25262 BRACKET 70. HA12315 22. HA23199 SWITCH INTERLOCK 71. HA12314 DECAL DANGER (HAND) DECAL DANGER 24. 712-0121 NUT #10-24 HEX 72. HA24431 DECAL OPERATION/CAUTION 25. 47078 SCREW #10-24 X 3/4" 74. HA126145 BOLT 1/2-13 X 7" HEX HEAD 26. 27. 48840 48298 SCREW 1/4-20 WASHER HEAD 75. 43982 28. HA24300 CLIP, CORD WHEEL MOUNTING BRACKET L.H. 76. 77. HA22981 HA24298 PIN, CLEVIS 1/4" X 5/8" BELT GUIDE 29. HA24301 WHEEL MOUNTING BRACKET 78. 49156 30. HA4143 WASHER FLAT 79 43013 ROD, CABLE GUIDE NUT 1/4-20 HEX 31. HA137258 PIN COTTER 3/16" X 1-3/4" 80. 44488 WHEEL BEARING 32. HA24308 TIRE 81. HA23754 SOLENOID 33. HA23229 CAP HUB 82. HA23749 STARTER SWITCH 34. HA24309 STRAP ADJUSTING 83. HA23750 SWITCH MOUNTING 35. HA6979 WASHER FLAT 84. HA23757 SWITCH COVER 36. 43020 BOLT 1/2-13 X 1-1/2 HEX HEAD 85. HA23752 KEY 37. 43019 NUT 1/2-13 HEX JAM 86. 25286 38. HA23220 PIN LOCATING 87. 49201 PLATE, SWITCH MOUNTING THROTTLE 39. 40. 47134 HA24311 PIN HAIR COTTER 88. 45040 SCREW, #10-24 X 1/2 CHAIN DEFLECTOR 89. 736-0722 41. HA24312 ROD CHAIN 90. 49198 LOCK WASHER, #10 BATTERY HOLD DOWN 42. HA24313 BRACKET CHANNEL 91. 49199 BOLT, BATTERY 43. HA9131 SCREW SELF THREADING 92. 49200 44. 25263 PLATE ENGINE MOUNTING 93. 25287 NUT, PLASTIC BATTERY COVER 45. 280H070130E1* ENGINE, 14.5 HP HA24457 PULLEY 94. 48840 SCREW, 1/4-20 X 1/2 HEX HEAD 46. 47. HA3073 * Order engine repair parts from your nearest Briggs & Stratton dealer. 18. 19. 25291 43661 20. INTERLOCK KEY 1/4" SQ. X 1" MOUNTING .08" X 1.58" R.H. ROLLER ROLLER MOWER SPRING RETURN SpeedEPartthe ra..e., to,urchparts .e www.speedepart.com 23 NUT 42" ROUGH CUT TRAILMOWER - MODEL 45-0362 24 42" ROUGH CUT TRAILMOWER - MODEL 45-0362 ITEM PART NO. DESCRIPTION 1. 64906 IDLER MOUNTING 2. 43070 WASHER FLAT 3. 4. 64899 24472 IDLER ARM 5. 6. 43003 43062 WASHER 3/8" LOCK 7. 49148 SPACER 8. HA21341 9. 43054 IDLER PULLEY (FLAT) BOLT 3/8-16 X 2" HEX HEAD 10. 43082 NUT 3/8-16 HEX LOCK 11. HA22981 GUIDE BELT 12. HA22224 SCREW 3/8-16 X 3/4 SELF TAPPING 13. 14. 43087 HA15200 BOLT 3/8-16 X 1-1/4" HEX HEAD 15. HA21362 NUT 3/8-16 NYLOCK 16. HA24367 GREASE FITTING 17. HA24278 18. HA24280 HUB (WITH STUDS) BEARING 19. 64913 HUB BLADE 20. 21. 49148 HA24282 SHAFT SPINDLE 22. HA3073 KEY 1/4" SQ X 1" 23. HA456151 WASHER 13/16 X 1-1/2 X .134 FLAT 24. HA427639 NUT 3/4-16 SLOTTED HEX 25. 26. 43010 HA24624 PIN 1/8" X 1" COTTER 27. HA24288 BLADE 28. HA24625 WASHER - FLAT 29. HA24592 BOLT - 7/8-9 X 2-1/4 HEX BOLT 30. HA137258 PIN 3/16 X 1-3/4 COTTER 31. HA24593 NUT 7/8-9 SLOTTED 32. 43353 WASHER 1/2 MED. LOCK 33. HA120371 NUT 1/2-20 HEX 34. HA24290 PULLEY SPINDLE 35. 64902 BRAKE 36. 49155 TRUNNION 37. 49160 BRAKE ROD 38. HA20186 SPRING BRACKET BUSHING BOLT 3/8-16 X 1-1/2" HEX HEAD WASHER FLAT SEAL O-RING DISC BLADE MOUNTING OIi##u ;rd/'i HEX thefastestwaytopurchaseparts www.speedepart.com 25 42" ROUGH CUT TRAILMOWER - MODEL 45-0362 ITEM PART NO. DESCRIPTION 16. 17. 43012 43013 BOLT 1/4-20 X 3/4 HEX HEAD HA20186 SPRING EXTENSION 19. HA23265 DECAL CLUTCH LEVER 4. 44180 BOLT 5/16-18 X 2' HEX HEAD 20. 64910 BRACKET DRAWBAR ADJUSTMENT 5. 43064 NUT 5/16-18 HEX LOCK 21. HA24326 DRAWBAR SWIVEL 6. 64909 HITCH ASSEMBLY 22. HA5074 FITTING GREASE 7. HA180132 43509 23. 24. HA15200 43003 WASHER 8. BOLT 3/8-16 X 2-1/4 HEX HEAD BOLT 3/8-16 X 2-3/4 HEX HEAD 9. 43070 WASHER 3/8 FLAT 25. 43087 BOLT 3/8-16 X 1-1/4 HEX HEAD 10. 43082 NUT 3/8-16 HEX LOCK 26. HA24330 PIN CLEVIS 11. HA23636 PIN CLEVIS 27. HA3341 12. 47134 PIN HAIR COTTER .08 X 1.58 29. HA23761 PIN HAIR COTTER, 5/32" CLIP HOSE 3/8" 13. 49157 LEVER CLUTCH 30. HA9411666 SCREW #10-16 X 1/2 SELF TAPPING 14. 43062 BOLT 3/8-16 X 1-1/2 HEX HEAD 31. 49193 WIRE HARNESS 15. HA19445 SPRING COMPRESSION ITEM PART NO. DESCRIPTION 1. 25273 2. HA24441 TUBE DRAWBAR STRAP HITCH 3. O/l##uA;rdrl (MODEL 45-0361) thelastest NUT 1/4-20 LOCK WASHER 3/8 LOCK (See page 27) topurchase parts www.speedepart.com 26 RED WIRE BATTERY CHARGE STARTER SWITCH BATTERY WIRE RED WIRE + BLUE WIRE-_ GRAY WIRE BLACK WIRE WIRE TO AFTERFIRE SOLENOID BLACK WIRE TO ENGINE GROUND "wuwlnmnn,, n SOLENOID n WHITE WIRE INTERLOCK SWITCH _4 n ITEM PART NO. DESCRIPTION 1. 49193 WIRE HARNESS 2. 49194 WIRE RED CHARGE 3. 49195 WIRE BLACK 4. 49192 WIRE INTERLOCK 5. 49244 WIRE GROUND 6. 49196 WIRE BLACK BATTERY 7. 49197 WIRE RED BATTERY 8. HA237888 WIRE RED STARTER 9. HA237544 SOLENOID 10. HA231999 SWITCH, INTERLOCK 11. HA237494 SWITCH, STARTER 12 2491545 CONDUIT, FLEXIBLE SpeedEPart_ _, _ __ _ REPAIR PARTS © 2004 Agri-Fab, Inc. Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com www.speedepart.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 28 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Wed Apr 04 14:12:40 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools