Airgun Designs E Mag Users Manual
2015-09-01
: Airgun-Designs Airgun-Designs-E-Mag-Users-Manual-804348 airgun-designs-e-mag-users-manual-804348 airgun-designs pdf
Open the PDF directly: View PDF 
.
Page Count: 49
| Download | |
| Open PDF In Browser | View PDF |
E-Mag Exploded View click on image Rail and Main Body Valve, Bolt, and Spring Frame and Electronics Battery and Charger E-Mag Rail Part #1410 Available in black only. Order Online Now! Back to Top Twist Lock Assembly Part #223 Assembly that holds the barrel in. Order Online Now! Back to Top Rail Bushing Part #129 The grip frame and rail are held in alignment with this bushing. It goes in the field strip screw hole. Order Online Now! Back to Top Sear Assembly Part #1386 The entire sear assembly for the E-mag. Comes preadjusted for trigger rod length and solenoid plunger position. Order Online Now! Back to Top Sear Axle Pin Part #775 Screws in the side of the marker into the sear bushing. Order Online Now! Back to Top Sight Rail Part #1392 Comes in black only. Order Online Now! Back to Top Sight Rail Screw Part #770 Very short flat head screws. Do not use hardware store screws; they might hit the sear. Order Online Now! Back to Top Main Body (Hopper Left) Part #1414 See the Main Body page under Upgrades for a complete selection. Order Online Now! Back to Top Grips Part #1297 Rubber E-mag grips, sold by the pair. Order Online Now! Back to Top Grip Screw/ Solenoid Mount Screw Part#1307 Grip screws, three per side. Also used to hold the solenoid mount in place. Order Online Now! Back to Top PCB and Solenoid Assembly Part #1639 PC board and solenoid as one ready to go assembly. Comes pre programmed too! Order Online Now! Back to Top Extender Button Part #1394 The little buttons in the back of the grip frame that are used to change the program settings. Order Online Now! Back to Top Field Strip Screw Part #432 The screw that holds in the entire valve assembly. Order Online Now! Back to Top Hall Harness Part #1304 This is the sensor that detects the magnet in the back of the trigger to fire the marker. Comes as a complete assembly. Order Online Now! Back to Top Hall Holder/ Bottom Part #1320 The bottom half of the holder for Hall Effect Sensor. Order Online Now! Back to Top Selector Lever Bolt Part #1309 This bolt holds the selector lever on its shaft. Order Online Now! Back to Top Hall Holder/ Top Part #1422 The top half of the sensor holder. Order Online Now! Back to Top LED Window Part #1316 Window inside of rubber grip that protects the LED display. Order Online Now! Back to Top Selector Switch Lever Part #1321 Selector lever that switches between electronic and manual modes. Connects to selector switch. Order Online Now! Back to Top Hall Mount Bolt Part #1310 Bolt that holds the Hall Effect sensor mounts. Order Online Now! Back to Top Selector Switch Part #1287 This switch controls if the marker is in electronic or manual mode. Be careful when removing this part; there are springs and ball detents under this piece. Order Online Now! Back to Top Nylon Bushing Part #1328 Insulator bushing for the battery contact screw in the front of the E-mag grip frame. Order Online Now! Back to Top Nylon Washer Part #1327 This is the other half of the insulator for the battery terminal mounting in the front of the grip frame. Order Online Now! Back to Top Wire Lead Part #1594 The power wire from the battery contact bolt in the front of the grip frame to the PC board. Order Online Now! Back to Top Positive Terminal Nut Part #1312 This nut is part of the positive battery contact. Order Online Now! Back to Top Positive Terminal Part #1311 This bolt is part of the positive battery contact and uses the nylon insulators to isolate it from the grip frame. Order Online Now! Back to Top Sear Lock Part #1462 If you are able to see the red line the marker is off safe and will fire. Be careful when removing this shaft; there are springs and ball detents in the frame. Order Online Now! Back to Top Safety Ball Part #195 Hard steel ball bearing used as the safety detent. Order Online Now! Back to Top Safety Spring Part #197 Spring that goes under the ball detent in the safety. Order Online Now! Back to Top Solenoid E Clip Part #1470 This clip holds in the solenoid plunger. Order Online Now! Back to Top Solenoid Mount Part #1325 Solenoid screws into this mount and the whole thing slides into the grip frame. Order Online Now! Back to Top E-Mag Trigger Part #1411 Entire ready-to-go trigger assembly. Includes magnets. Does not come in colors. Order Online Now! Back to Top Magnet (Five Pack) Part #1313 Super strong rare earth magnet that is used to adjust trigger tension. Take them out for less, add them for more tension. Order Online Now! Back to Top Trigger Pin Part #1314 The axle for the sear. The original pin needs to be pressed out from the right side of the marker (side without the E-mag logo on valve). The new pin gets pressed in from the left side. Order Online Now! Back to Top Battery Pack Housing Complete Part #1393 Complete housing assembly; battery not included. Comes in black only. Order Online Now! Back to Top Battery Pack Part #1223 This is the complete NiMh battery pack including contacts. Don't forget to recharge before use and remember to put the spacer o-ring back in the bottom of the housing. Order Online Now! Back to Top Battery Saver Plug Part #1319 This is the pin that turns the battery on and off. Make sure you remove before flight! Order Online Now! Back to Top E-Mag O-ring Battery Bottom Part # 1646 This o-ring goes under the battery pack inside the battery housing so the battery makes good contact and does not rattle. Order Online Now! Back to Top Battery Housing Screws Part #1220 These are the bolts that hold the battery case together. Order Online Now! Back to Top Battery Charger Cord Part #1388 Standard cigarette lighter adapter cord. Plugs into battery recharger. Order Online Now! Back to Top Charger Assembly Part #1487 Battery charger for E-mag. Does not have the cigarette lighter adapter. Takes 12VDC input. Order Online Now! Back to Top Solenoid Part #1237 Solenoid that pulls the sear to fire the marker. Must be soldered to the PC board. Order Online Now! Back to Top www.airgun.com www.automags.org Airgun-UK Email to: office@airgun.com Office hours: 9:00 am - 5:00 pm (Central Time) Monday through Friday Office Tel: (847) 520-7507 Office Fax: (847) 520-7848 ------------------------------------Tech Support hours: 10:00 am to 11:30 am, 1:00 pm - 4:00 pm (Central Time) Monday through Friday Tech Support Tel: (847) 520-7225 Back to Top
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2002:03:01 20:26:52Z Modify Date : 2002:03:04 11:09:25-06:00 Page Count : 49 Creation Date : 2002:03:01 20:26:52Z Mod Date : 2002:03:04 11:09:25-06:00 Producer : Acrobat Distiller 5.0 (Windows) Author : john Metadata Date : 2002:03:04 11:09:25-06:00 Creator : john Title : Microsoft Word - E-MagEXIF Metadata provided by EXIF.tools