Alarm Lock Marks_M9900_WI2051 M99.06_INST ET PDL Trilogy Panic Exit Device Trim Instructions And For Marks M9900 Rim Devic WI2051 M99.06 INST

User Manual: Alarm Lock ET-PDL Trilogy Panic Exit Device Trim Instructions and for Marks M9900 Rim Exit Devic Installation Manuals

Open the PDF directly: View PDF PDF.
Page Count: 1

DownloadAlarm Lock Marks_M9900_WI2051-M99.06_INST ET-PDL Trilogy Panic Exit Device Trim Instructions And For Marks M9900 Rim Devic WI2051-M99.06 INST
Open PDF In BrowserView PDF
Trilogy® Panic Exit Device Trim

INSTRUCTIONS & TEMPLATE

DRILL BOTH
SIDES

Horizontal
Line

ETDL
SERIES

1

ETPDL
SERIES

Marks

1. Existing Installations: Remove the existing
Exit Device from the door. Position Alarm
Lock template (on this sheet) on the horizontal
& vertical lines of the existing spindle hole.
New Installations: Use the Marks template
to mount the Marks Exit Device on the door.
Remove Exit Device and use the Alarm Lock
template (on this sheet) to locate and line up
the template with the horizontal and vertical
lines indicated and tape on the door.
Existing and New Installations: Mark all
hole centers on each side of door (four
"THRU-BOLT HOLES", one "SPINDLE
HOLE" and one "WIRES HOLE"). Drill all
holes from both sides of door to avoid splintering. Drill all thru holes STRAIGHT through the
door.

Model M9900
Rim Exit Device

WIRES
HOLE
3/4"

Model M9900

Vertical
Line

Note: The
Spindle
Hole must
be no less
than 1"
diameter.

Marks

Battery
Cover

2

TWO
THRUBOLT
HOLES
5/16"

Exit Device
Cover

2. Position Exterior Assembly on door (shown above).

1.375"
4.84"

DRILL BOTH
SIDES

SPINDLE
HOLE
1" MINIMUM

Four #8 X 3/4"
"combination" flat
head screws

1/8"
min.
Four
#8#8-32 x 1¾"
Phillips pan
head
screws,
screws, with
washers

3
3. Replace Exit Device and fasten with four #8-32 x
1¾" Phillips pan head screws and washers (do
not over-tighten). Pull wires through Battery
Mounting Plate (do not pinch or cut wires) and
position Battery Mounting Plate a minimum of 1/8"
above Exit Device, and fasten with four #8 x 3/4"
"combination" flat head screws.

DRILL BOTH
SIDES

7.00"

4
4. Connect the Battery Pack (batteries may be
shrink wrapped or may be inside a selfcontained housing) and secure inside the
Battery Cover with the hook and loop fastener (provided). Position the Battery Cover
and fasten with four #6-32 x 5/16" screws.

HORIZONTAL
LINE

Fasten Exit Device Cover and fasten with
the four screws provided (as detailed in the
Marks installation instructions).
3.50"

Check lock for proper operation
before closing door.

VERTICAL LINE

ET-PDL

TWO
THRUBOLT
HOLES
5/16"
DRILL BOTH
SIDES

To Change Cylinder
IMPORTANT:
When replacing cylinder
be sure to use the
proper Cylinder Adapter
and Tailpiece.
Alarm Lock Systems, Inc.
A division of the NAPCO Security Technologies, Inc.
345 Bayview Avenue, Amityville, NY 11701
Tel: (631) 789-4871 Fax: (631) 789-3383
www.alarmlock.com
Publicly traded on NASDAQ

TailPiece

A
A. Remove Cover plate. Rotate the
spindle either direction to expose
and remove cylinder screws.

B
B. Remove old cylinder and insert new cylinder.

C
C. Note: The tailpiece must be in the
horizontal position as shown in the
image above.

© 2013 Alarm Lock
Systems, Inc.

Symbol: NSSC

WI 2051-M99 02/13
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2013:02:08 10:28:57-05:00
Modify Date                     : 2013:02:08 10:28:57-05:00
Page Count                      : 1
Creation Date                   : 2013:02:08 15:28:57Z
Mod Date                        : 2013:02:08 15:28:57Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : dblock
Metadata Date                   : 2013:02:08 15:28:57Z
Creator                         : dblock
Title                           : Marks_M9900_WI2051-M99.06_INST.pub
EXIF Metadata provided by EXIF.tools

Navigation menu