Alarm Lock Marks_M9900_WI2051 M99.06_INST ET PDL Trilogy Panic Exit Device Trim Instructions And For Marks M9900 Rim Devic WI2051 M99.06 INST
User Manual: Alarm Lock ET-PDL Trilogy Panic Exit Device Trim Instructions and for Marks M9900 Rim Exit Devic Installation Manuals
Open the PDF directly: View PDF 
.
Page Count: 1
ET-PDL
Trilogy® Panic Exit Device Trim
INSTRUCTIONS & TEMPLATE
Marks
Model M9900
Rim Exit Device
To Change Cylinder
Alarm Lock Systems, Inc.
A division of the NAPCO Security Technologies, Inc.
345 Bayview Avenue, Amityville, NY 11701
Tel: (631) 789-4871 Fax: (631) 789-3383
www.alarmlock.com
Publicly traded on NASDAQ Symbol: NSSC
1. Existing Installations: Remove the existing
Exit Device from the door. Position Alarm
Lock template (on this sheet) on the horizontal
& vertical lines of the existing spindle hole.
New Installations: Use the Marks template
to mount the Marks Exit Device on the door.
Remove Exit Device and use the Alarm Lock
template (on this sheet) to locate and line up
the template with the horizontal and vertical
lines indicated and tape on the door.
Existing and New Installations: Mark all
hole centers on each side of door (four
"THRU-BOLT HOLES", one "SPINDLE
HOLE" and one "WIRES HOLE"). Drill all
holes from both sides of door to avoid splinter-
ing. Drill all thru holes STRAIGHT through the
door.
2. Position Exterior Assembly on door (shown above).
3. Replace Exit Device and fasten with four #8-32 x
1¾" Phillips pan head screws and washers (do
not over-tighten). Pull wires through Battery
Mounting Plate (do not pinch or cut wires) and
position Battery Mounting Plate a minimum of 1/8"
above Exit Device, and fasten with four #8 x 3/4"
"combination" flat head screws.
Check lock for proper operation
before closing door.
A. Remove Cover plate. Rotate the
spindle either direction to expose
and remove cylinder screws. B. Remove old cylinder and insert new cylinder. C. Note: The tailpiece must be in the
horizontal position as shown in the
image above.
A
B
TailPiece
IMPORTANT:
When replacing cylinder
be sure to use the
proper Cylinder Adapter
and Tailpiece.
Battery
Cover
C
C
VERTICAL LINE
TWO
THRU-
BOLT
HOLES
5/16"
DRILL BOTH
SIDES SPINDLE
HOLE
1" MINIMUM
DRILL BOTH
SIDES
HORIZONTAL
LINE
WIRES
HOLE
3/4"
DRILL BOTH
SIDES
4.84"
7.00"
3.50"
TWO
THRU-
BOLT
HOLES
5/16"
DRILL BOTH
SIDES
1.375"
Marks
Model M9900
© 2013 Alarm Lock
Systems, Inc.
WI 2051-M99 02/13
4
4
4
ETDL
SERIES
ETPDL
SERIES
Note: The
Spindle
Hole must
be no less
than 1"
diameter.
1
1
Vertical
Line
Horizontal
Line
2
2
3
Four
Four
#8
#8-
-32 x 1¾"
32 x 1¾"
Phillips pan
Phillips pan
head
head
screws
screws, with
, with
washers
washers
Four #8 X 3/4"
Four #8 X 3/4"
"combination" flat
"combination" flat
head screws
head screws
1/8"
1/8"
min.
min.
4. Connect the Battery Pack (batteries may be
shrink wrapped or may be inside a self-
contained housing) and secure inside the
Battery Cover with the hook and loop fas-
tener (provided). Position the Battery Cover
and fasten with four #6-32 x 5/16" screws.
Fasten Exit Device Cover and fasten with
the four screws provided (as detailed in the
Marks installation instructions).
Exit Device
Cover
