Alarm Lock Networx_V5.1.1_OI383.52_USER DL Windows For Trilogy Networx V5 User's Guide V5.1.1 OI383.52 USER

User Manual: Alarm Lock DL-Windows for Trilogy Networx V5 User's Guide User Guides

Open the PDF directly: View PDF .
Page Count: 56

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 1

© ALARM LOCK 2014

PDL6100

PDL6500

&

ETPDLN

DL6100

DL6500

&

ETDLN

PL6100

PL6500 &

ETPLN

NETPDK

NETDK NETWORXPANEL

Downloading Software for the

Trilogy® Networx™ Line

of Access Control Systems

DL-WINDOWS™ for Networx™

V5 USER'S GUIDE

345 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs 1-800-ALA-LOCK

For Technical Service 1-800-645-9440

or visit us at http://tech.napcosecurity.com/

(Note: Technical Service is for

security professionals only)

Publicly traded on NASDAQ Symbol: NSSC

Gateway "Wireless/Wired"

AL-IM80211

OI383 01/14

(replaces OI352D)

2 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

The following changes have been made to this manual OI383 (identical to OI352D) since the previous edition (OI352C):

• Updated to reflect DL-Windows version 5 which includes a new look, improved performance and simplified screens.

• Removed the section regarding Gateway hardware installation (page 11 of OI352C) and placed it into a new man-

ual ("Networx Gateway Installation and Setup Instructions", WI2085).

CHANGES FROM THE PREVIOUS EDITION

About this Manual

This manual is intended to document the DL-Windows computer screens and features used to program Networx wireless

door locks and devices.

The word "lock" is a generic word used to indicate one of the many Alarm Lock locking devices available, including de-

vices such as the DK series keypads that trigger other

locking devices.

The word "credential" is also a generic word used to in-

dicate a PIN number pressed into a lock keypad, or a

proximity card or proximity keyfob.

In DL-Windows, the word "configure" has a specific

meaning--to "configure" is to "assign" discovered physical

locks to a Gateway, thus ensuring a fixed wireless com-

munication channel exists between selected physical

locks and a selected Gateway.

Throughout this manual, the phrase "DL-Windows 'Main

Screen' " is often used, and refers to the first screen that

opens when the DL-Windows program is launched,

shown at right. Also note that when Accounts are added,

they are listed in the "Account List" area, also shown:

Important: Trilogy® is a registered trademark of Alarm Lock. ProxCard® and ProxKey® are trademarks of the HID© Corporation.. Microsoft® and Windows® are trademarks of their the

Microsoft Corporation. All other trademarks, service marks, and product or service names described in this manual are for identification purposes only and may be trademarks or

registered trademarks of their respective owners. The absence of a name or logo in this document does not constitute a waiver of any and all intellectual property rights that NAPCO

Security Technologies, Inc. has established in any of its product, feature, or service names or logos. Screen images, icons and instructions in this guide may vary depending on the

software version installed. The information in this manual is for informational purposes only and is subject to change without notice. Companies, names and data used in examples

herein are fictitious unless otherwise noted. Alarm Lock assumes no responsibility for incorrect information this manual may contain.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meas-

ures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and the receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003. Changes and Modifications not expressly approved by Napco

can void your authority to operate this equipment under Federal Communications Commissions rules.

Radio and Television Interference

DL-Windows "Main Screen"

This white area is called the

"Account List" area.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 3

Table of Contents

Radio and Television Interference ................................................................................................................................................. 2

Changes From The Previous Edition ............................................................................................................................................. 2

About this Manual............................................................................................................................................................................ 2

Ordering Information ....................................................................................................................................................................... 4

Overview ........................................................................................................................................................................................... 6

Gateway Specifications................................................................................................................................................................... 8

Quick Start .......................................................................................................................................................................................9

Security Password.........................................................................................................................................................................10

"Gateway Configuration" Screen - Field and Button Definitions............................................................................................ 11

Discovering / Adding Gateways ................................................................................................................................................... 12

Color List ........................................................................................................................................................................................ 12

Discovering / Assigning Wireless Locks..................................................................................................................................... 13

Linking Lock Profiles..................................................................................................................................................................... 14

Gateway Configuration > Tools > View Gateway Status............................................................................................................15

Gateway Configuration > Tools > View Gateway's Lock Table ................................................................................................. 16

Gateway Configuration > Tools > Delete Lock(s) by Serial Number(s) ....................................................................................17

Gateway Configuration > Tools > Configure / Edit Network Settings.......................................................................................18

Gateway Configuration > Tools > Ping Gateway ........................................................................................................................ 20

Gateway Configuration > Tools > Update Gateway Firmware................................................................................................... 20

Gateway Configuration > Tools > Manually Add a Lock to the Gateway ................................................................................. 21

Gateway Configuration > Tools > Set Emergency Groups ........................................................................................................ 22

Gateway Configuration > Tools > Import Assigned Lock .......................................................................................................... 22

Gateway Configuration > Tools > Send Lock Config Table to the Gateway ............................................................................22

Gateway Configuration > Tools > Import Gateway and Assigned Locks.................................................................................23

Gateway Configuration > Tools > Show WAN / Port Information..............................................................................................24

Gateway Configuration > Tools > Select Network Adapter .......................................................................................................24

Gateway Configuration > Tools > Manually Add a Gateway......................................................................................................25

Gateway Configuration > Actions > Add Gateway to Account..................................................................................................26

Gateway Configuration > Actions > Remove Gateway from Account ......................................................................................26

Gateway Configuration > Actions > Locate All Locks on Gateway ..........................................................................................27

Gateway Configuration > Actions > Discover Locks.................................................................................................................. 27

Gateway Configuration > Actions > Discover New Gateways .................................................................................................. 27

Gateway Configuration > Actions > Relocate Gateways (Displayed in red) ............................................................................ 28

Gateway Configuration > Actions > Replace Gateway with New One ..................................................................................... 29

Gateway Configuration > Actions > Gateway Signal Test Mode............................................................................................... 30

Communicating with Wireless Locks .......................................................................................................................................... 31

"Wireless" Screen - Field and Button Definitions.......................................................................................................................34

"Wireless Schedule" Screen - Field and Button Definitions...................................................................................................... 35

Wireless Actions Menu..................................................................................................................................................................36

"Emergency Commands" Screen - Field and Button Definitions ............................................................................................. 37

Using Emergency Commands ...................................................................................................................................................... 38

Emergency > Emergency Lock Down.......................................................................................................................................... 40

Emergency > Emergency Passage .............................................................................................................................................. 41

Emergency > Emergency Return to Normal................................................................................................................................ 42

Emergency Commands > Set Emergency Groups ..................................................................................................................... 43

Networx Lock Right-Click Profile Menu....................................................................................................................................... 45

Right-Click Menu > View Status of Lock ..................................................................................................................................... 46

Right-Click Menu > Link / Unlink Lock Profile ............................................................................................................................ 47

Right-Click Menu > Locate Lock .................................................................................................................................................. 48

Right-Click Menu > Update Date / Time in Lock ......................................................................................................................... 48

Right-Click Menu > Take Lock Out of Passage........................................................................................................................... 48

Right-Click Menu > Put Lock Into Passage .................................................................................................................................49

Right-Click Menu > Update Lock Firmware................................................................................................................................. 49

Troubleshooting.............................................................................................................................................................................50

Glossary.......................................................................................................................................................................................... 52

Alarm Lock Limited Warranty ....................................................................................................................................................... 56

4 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Several Gateway device models are available; all have

the two antennas used to transmit to the locks via an

Alarm Lock proprietary radio connection.

● Gateway "Wireless/Wired" AL-IM80211 - Hardwired/

Wireless Gateway Interface Module. Supplied with its

own Class 2 transformer to supply power; connection to

a network is supported via either a wired connection

(using a standard RJ-45 Ethernet cable) or a wireless

connection (using a third antenna for 802.11

transmissions). Ensure adequate 802.11 coverage in

the area where the "Wireless/Wired" Gateway is

mounted. Supports up to 63 Networx Locks. Ceiling-

or wall-mountable.

● Gateway "Wired" AL-IME - Hardwired Gateway

Interface Module, supports up to 63 Networx Locks,

connects directly to a network using a standard RJ-45

Ethernet cable. Ceiling- or wall-mountable; powered

with Class 2, 6VAC transformer (supplied).

● Gateway "Power over Ethernet" AL-IMEPOE -

Hardwired Gateway Interface Module + POE (Power

Over Ethernet), supports up to 63 Networx Locks,

connects directly to a network using a standard RJ-45

Ethernet cable and POE. Ceiling- or wall-mountable.

● Gateway "Plenum Rated POE" AL-IMEPOEP - Same

as above "AL-IMEPOE", with added enclosure

protections and installation hardware for mounting

above "drop-ceiling" tiles or other locations subject to

air pressure changes (HVAC air-filled spaces, etc.).

● PDL6100 - Cylindrical Trilogy® Networx™ Wireless

Access Control Lock with built in HID Proximity ID Card

Reader, full-metal digital keypad, integral bi-directional

radio, 4 C-cell battery-operated (batteries supplied),

serial number ID card, standard format SC1 keyway for

manual key override, 4⅞" ASA Strike (included).

● DL6100 - Cylindrical Trilogy® Networx™ PIN-Code

Wireless Access Control Lock, as above, with metal

digital keypad only. Standard format SC1 keyway for

manual key override, 4⅞" ASA Strike (included).

● PDL6200 - Cylindrical Trilogy® Networx™ Wireless

Access Control Lock with added Door Monitoring

features, including logged entry and exit, "Door

Ajar" (valid credential entered and door opened but not

closed within the programmed time), and "Forced

Entry" (door opened without a valid credential entered

or without inside lever turned). Includes built in HID

Proximity ID Card Reader, full-metal digital keypad,

integral bi-directional radio, 4 C-cell battery-operated

(batteries supplied), serial number ID card, standard

format SC1 keyway for manual key override, 4⅞" ASA

Strike (included).

● PDL6500 - Mortise Trilogy® Networx™ Wireless Access

Control Lock with built in HID Proximity ID Card Reader,

Ordering Information

full-metal digital keypad, integral bi-directional radio,

supplied batteries and serial number ID card. Standard

format SC1 keyway for manual key override, 4⅞" ASA

Strike (included).

● DL6500 - Mortise Trilogy® Networx™ Wireless Access

Control Lock with full-metal digital keypad, integral bi-

directional radio, supplied batteries and serial number

ID card. Standard format SC1 keyway for manual key

override, 4⅞" ASA Strike (included).

● PDL6600 - Mortise Trilogy® Networx™ Wireless Access

Control Lock with added Door Monitoring features (see

PDL6200 for details). Includes built in HID Proximity ID

Card Reader, full-metal digital keypad, integral bi-

directional radio, supplied batteries and serial number

ID card. Standard format SC1 keyway for manual key

override, 4⅞" ASA Strike (included).

● PDL7100 - Cylindrical Trilogy® Networx™ Wireless

Access Control Lock with built in Proximity iCLASS

Smart Card Reader, full-metal digital keypad, integral bi-

directional radio, 4 C-cell battery-operated (batteries

supplied), serial number ID card, standard format SC1

keyway for manual key override, 4⅞" ASA Strike

(included).

● PL6100 - Cylindrical Trilogy® Networx™ Wireless

Access Control Lock with built in HID Proximity ID Card

Reader (keypad removed for added security), integral

bi-directional radio, 4 C-cell battery-operated (batteries

supplied), serial number ID card, standard format SC1

keyway for manual key override, 4⅞" ASA Strike

(included).

● PL6200 - Cylindrical Trilogy® Networx™ Wireless

Access Control Lock with added Door Monitoring

features (see PDL6200 for details). Includes built in

HID Proximity ID Card Reader (keypad removed for

added security), integral bi-directional radio, 4 C-cell

battery-operated (batteries supplied), serial number ID

card, standard format SC1 keyway for manual key

override, 4⅞" ASA Strike (included).

● PL6500 - Mortise Trilogy® Networx™ Wireless Access

Control Lock with built in HID Proximity ID Card Reader

(keypad removed for added security), integral bi-

directional radio, supplied batteries and serial number

ID card. Standard format SC1 keyway for manual key

override, 4⅞" ASA Strike (included).

● PL6600 - Mortise Trilogy® Networx™ Wireless Access

Control Lock with added Door Monitoring features (see

PDL6200 for details). Includes built in HID Proximity ID

Card Reader (keypad removed for added security),

integral bi-directional radio, supplied batteries and serial

number ID card. Standard format SC1 keyway for

manual key override, 4⅞" ASA Strike (included).

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 5

● ETPDLN, ETDLN & ETPLN - Exit Trim Trilogy

Networx™ Wireless Access Control Locks for most

major manufacturers exit devices. ETPDLN and

ETPLN include built in HID Proximity ID Card Reader

(ETPLN for proximity-only). ETPDLN and ETDLN

include full-metal digital keypad. All include integral bi-

directional radio, 4 C-cell battery-operated (batteries

supplied), serial number ID card, standard format SC1

keyway for manual key override.

● NETDK, NETPDK & NETWORXPANEL - The NETDK

and NETPDK (with proximity card reader) are secured

single-door or double-door digital keypads for use within

the wireless Networx™ system. One or two keypads

can be wired to the dedicated NETWORXPANEL

control panel to provide controlled access to a door by

releasing a locking device (such as a magnetic lock or

electric door strike) when a proper User Code (and/or a

proximity credential to the NETPDK) is presented. The

NETWORXPANEL inputs support two of any

combination of NETDK or NETPDK keypads, PLUS up

to two Wiegand devices. See WI1881, WI1855 and

WI1856 for additional information.

● ETPDLNRX & ETPLNRX - Exit Trim Trilogy Networx™

Wireless standalone access control locks for most

major manufacturers exit devices with added Door

Monitoring features (see PDL6200 for details). The

ETPDLNRX includes both a 12-button metal keypad

and a built in HID Proximity ID Card Reader (ETPLNRX

for proximity-only). All include integral bi-directional

radio, 4 C-cell battery-operated (batteries supplied),

serial number ID card, standard format SC1 keyway for

manual key override.

● DL-WINDOWS - Alarm Lock Trilogy Microsoft

Windows-based software application, v4.0.0 or higher,

supports Trilogy Networx and Trilogy Standalone Locks,

with single database. Free of charge and downloadable

online at www.alarmlock.com.

Ordering Information (cont'd)

● OI382 - DL-Windows User's Guide (non-Networx),

replaces OI237K.

● OI383 - DL-Windows for Networx User's Guide (this

manual), replaces OI352D.

● WI2085 - Networx Gateway Installation & Setup

Instructions

● OI362 - Networx Quick Start Guide.

● WI1790 - PDL6100 Keypad Programming Instructions.

● WI1820 - DL6100 Keypad Programming Instructions.

● WI1835 - PDL6500 & ETPDLN Keypad Programming

Instructions.

● WI1836 - DL6500 & ETDLN Keypad Programming

Instructions.

● WI1843 - PL6100 Programming Instructions.

● WI1844 - PL6500 & ETPLN Programming Instructions.

● WI1674 - PDL6100 and DL6100 Installation

Instructions.

● WI1676 - PDL6100 and DL6100 Door Installation

Template.

● WI1881 - NETDK & NETPDK Installation Instructions

● WI1855 - NETWORXPANEL Programming Instructions

with the NETDK & NETPDK keypads

● WI1856 - NETWORXPANEL Installation Instructions

● WI2024 - PDL6200 & DL6200 Installation Instructions

● WI2027 - PDL6600 & ETPDLNRX Programming

Instructions

● WI2036 - PDL6600 & DL6600 Template

● WI2059 - PL6600 & ETPLNRX Programming

Instructions

See www.alarmlock.com for a complete list of all available

standard Trilogy and Networx™ series devices and manuals

(downloadable in PDF format).

6 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Used with the Trilogy Networx™ series door locks and

keypads, DL-Windows (version 4.0.0 software or later)

allows you to upload and download programming fea-

tures wirelessly using a computer network. With

"wireless" communication, the various cables and/or an

AL-DTM Data Transfer Module are NOT required to

transfer data between DL-Windows and the wireless

locks. Simply use your computer to retrieve logs,

download User Codes and program features into each

wireless lock in the system.

DL-Windows software is installed on a computer that is

connected to a network (either a small Ethernet network,

a large corporate LAN, or over the Internet). Connected

to this network is an intermediate device called a Gate-

way that communicates via a private wireless signal to a

radio located inside each door lock. In this way, the soft-

ware allows full programming and control of each lock in

the system. Note: In this manual, the word "lock" refers

to all Networx™ series door locks and the NETWORX-

PANEL wireless control panel and its wireless keypads.

To ensure each physical lock is identified correctly by

DL-Windows, the factory assigns each lock a unique se-

rial number; after locks are installed on the doors and the

Gateways are mounted, the Gateways search for new

locks, allowing them to be enrolled into the system.

FLEXIBLE SETUP

In addition to wireless communication, these wireless

door locks can also be programmed at the keypad

(see the keypad programming instructions included with

the lock). This means that locks can be installed on the

doors and immediately be put into use via keypad pro-

gramming--even before a wireless network is set up.

Therefore, you can install the locks on the doors before

configuring the wireless network, or you can set up the

wireless network first and add locks later. If you wish,

you can even start by designing a "virtual" system within

DL-Windows (creating new Accounts, adding Users and

configuring lock features, etc.), then set up the network

and install the lock hardware later. But in the end, after

your lock hardware is physically installed and the net-

work is up and running, you can run DL-Windows to

"Link" the "virtual" system saved on your computer with

the "real" lock hardware on the doors.

Note: Keypad programming of User Codes, Features,

Time Zones, and Schedules is available as a temporary

convenience to allow the lock to be put into use before

installing and configuring a wireless network. Therefore,

all lock programming added via the keypad cannot be

retrieved into DL-Windows. If you decide to start

programming your wireless lock via the keypad, we

recommend you keep hardcopy records (in a secure

location) of all Users, their User Codes, and any

proximity cards that may have been programmed. Keep-

ing complete and accurate records saves time because

after the wireless network is set up, any programming

added via the keypad must be re-added to DL-Windows

and downloaded back to the lock(s).

CAPACITY

Each installed system can contain from 1 to 32 Gate-

ways--and each Gateway can control up to 63 locks--for

a maximum of 2000 locks allowed per Account; and the

DL-Windows software can support, in theory, an unlim-

Overview

Up to 63 locks for

each Gateway...

PC Running

DL-Windows

Software

EXPANDABLE

Wired (RJ-45)

or Wireless

Wired (RJ-45)

or Wireless 802.11

Router

Small Network Support

Wired (RJ-45)

or Wireless 802.11

...Up to 32 Gateways

for each system

GATEWAY

#1

GATEWAY

#32

Radio )

)

)

) )

Radio )

)

)

) )

Radio )

)

)

)

Lock

#1...

Lock

#63

...Lock

#2000

Existing

Corporate

Ethernet

Network

Up to 63 locks for

each Gateway...

PC Running

DL-Windows

Software

EXPANDABLE

Wired (RJ-45)

or Wireless

Wired (RJ-45)

or Wireless 802.11

Large Network Support

Wired (RJ-45)

or Wireless 802.11

...Up to 32 Gateways

for each system

GATEWAY

#1

GATEWAY

#32

Radio )

)

)

) )

Radio )

)

)

) )

Radio )

)

)

)

Lock

#1...

Lock

#63

...Lock

#2000

Up to 63 locks for

each Gateway...

...or PC Running

DL-Windows Software

EXPANDABLE

Internet Gateway Connectivity Support

...Up to 32 Gateways

for each system

GATEWAY

#1

GATEWAY

#32

Radio )

)

)

) )

Radio )

)

)

) )

Radio )

)

)

)

Lock

#1...

Lock

#63

...Lock

#2000

Wired (RJ-45)

or Wireless 802.11

Wired (RJ-45)

or Wireless 802.11

Wired (RJ-45)

or Wireless

Internet

Laptop...

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 7

ited number of Accounts. In addition, each Networx™

lock can contain up to 5000 Users!

MINIMUM WIRELESS SYSTEM

As shown in the "overview" drawings above, you do not

need a massively complex corporate network to run a

working system. In fact, a minimum wireless system

may consist of a laptop or desktop computer (to run

DL-Windows), a router (to allow connection to a com-

puter network), and an Alarm Lock Gateway module

(the intermediary between the network and the locks).

NETWORK SECURITY

The system uses AES (Advanced Encryption Standard)

to protect the integrity of the data flow between the wire-

less router / network and the Gateways.

Overview (cont'd)

DL-Windows software is the basis for wireless lock programming. For those unfamiliar with using

DL-Windows software or if DL-Windows is not yet installed, stop here and review the DL-Windows User Guide (OI382).

It may be helpful to create a "test" Account in DL-Windows, where you can add Lock Profiles and become familiar with

the DL-Windows program while working through the examples presented in this manual and in OI382.

If you are already familiar with DL-Windows, the transition to working with wireless locks will be straightforward with

slight changes in terminology. If you want to get started right away to see the system work, see the Quick Start section

on page 9. This manual can be read from beginning to end, or can be used with the Table of Contents as a reference

manual.

● To install locks on the doors first, use the Installation Instructions for the lock model you wish to install, then

use the keypad Programming Instructions to put the locks into use.

● To install and set up Gateways and configure your network settings, see the Networx Gateway Installation &

Setup Instructions (WI2085).

DL-WINDOWS SYSTEM REQUIREMENTS

See OI382 for a complete list of the minimum requirements, plus things to consider when upgrading from previous

versions, and the step-by-step procedures for installing DL-Windows version 5.

IMPORTANT - Please Read This

8 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Model AL-IM80211

("Wireless/Wired" Gateway)

Wireless Specifications

Wireless Standards: IEEE 802.11b; 802.11g

Frequency Range: 2.412 – 2.484 GHz

Output Power: 14dBm +1.5 dBm/-1.0 dBm

Maximum Receive Level: -10dBm (with PER < 8%)

Data Rates with Automatic Fallback: 54Mbps –

1Mbps

Modulation Techniques: OFDM, DSSS, CCK,

DQPSK, DBPSK, 64 QAM, 16 QAM

Network Interface

Interface: Ethernet 10Base-T or 100Base-TX (using

RJ-45 jack)

Protocols: TCP/IP, UDP/IP, DHCP

Security

128-bit AES encryption

Power Consumption

Average Power Consumption:

● 1300mW (WLAN mode; maximum data rate)

● 300mW (WLAN mode; idle)

● 750mW (Ethernet mode)

Input Voltage: 5 - 6 Volts AC/DC

Peak Supply Current: 650mA

Environmental

Operating Temp: -20° to 60°C (-4° to 140°F)

Storage Range: -40° to 85°C (-40° to 185°F)

Model AL-IME

("Wired" Gateway)

Network Interface

Interface: Ethernet 10Base-T or 100Base-TX (using

RJ-45 jack)

Protocols: TCP/IP, UDP/IP, DHCP

Security

128-bit AES encryption

AL Radio Link

900MHz

50 Channels

10mW power output

Input Power

Voltage: 5 - 6 Volts AC/DC

Peak Supply Current: 500mA

Environmental

Operating Temp: -20° to 60°C (-4° to 140°F)

Storage Range: -40° to 85°C (-40° to 185°F)

Gateway Specifications

Model AL-IMEPOE

("Power Over Ethernet" Gateway)

Model AL-IMEPOEP

("Plenum Rated POE" Gateway)

Network Interface

Interface: Ethernet 10Base-T or 100Base-TX (using

RJ-45 jack)

Protocols: TCP/IP, UDP/IP, DHCP

Security

128-bit AES encryption

AL Radio Link

900MHz

50 Channels

10mW power output

Input Power

POE Voltage: 48 Volts DC nominal

Class 2

Environmental

Operating Temp: -20° to 60°C (-4° to 140°F)

Storage Range: -40° to 85°C (-40° to 185°F)

Compliance

802.3af POE Standard (AL-IMEPOEP only)

UL 2043: UL Standard for Safety Fire Test for Heat

and Visible Smoke Release for Discrete Products

and Their Accessories Installed in Air-Handling

Spaces

For all Gateway modules, network activity (or bandwidth usage) does NOT occur until you operate DL-Windows software to

send programming to (or receive log data from) physical locks. Exception: During the Emergency Lockdown Command,

Gateways communicate through the network. Gateways will send less than 1000 bytes during these Emergency

Commands (for more information regarding Emergency Commands, see page 38).

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 9

1. Install the DL-Windows software (see OI382).

2. Setup your Network connection and install your Gateway (see WI2085). Note: Complete the

blue Gateway ID Card specifying its physical location. Horizontal "flat" mounting of the Gateway

enclosure should be avoided.

3. Connect the Gateway to the Network, then power up the Gateway (see WI2085).

4. Start DL-Windows and add a new Account (see OI382).

5. Create Lock Profiles for each physical wireless lock (see OI382). Lock Profiles will be required

for Linking to physical locks after discovery. Note: See Ordering Information on page 4 for

supported lock models.

6. Add Users, create Schedules and set Features for each lock (see OI382). Note: This step may

be performed after the Linking process described in step 12 below.

7. Set Security Password (see OI382). You cannot perform the next step without the Security

Password being set.

8. Click the Gateway Config button (see page 11).

9. Click the Discover Gateways And Auto Add button (see page 11).

10. In the Gateway Configuration screen, click to highlight and select the desired Gateway, set the

Number of Locks to Discover, then click the Discover Locks button (page 13).

11. Select discovered lock(s) by serial number and click Assign (page 13).

12. Link lock(s) to Lock Profile(s) (page 14). In the Link / Unlink Lock Profiles screen:

a. In the Available Lock Profiles field: Click to highlight a Lock Profile.

b. In the Available Lock(s) By Serial Number field: Click to select the desired physical lock (by

serial number) to be Linked to the Lock Profile.

13. "Download" Lock Profile to lock(s) (see OI382).

Congratulations! Locks can now communicate wirelessly. Use the Communication button in

the Lock screen (see OI382), or communicate with multiple locks using the Wireless screen (page

34).

Quick Start

10 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Security Password

Overview

Before Gateways and locks can be discovered and

configured, a Security Password must be set for the

Account. The Security Password creates a secure

connection between DL-Windows, your Gateways and the

physical locks. Once set, the Security Password is

embedded within the radio transmissions, also preventing

separate Accounts from overlapping their wireless signals.

IMPORTANT: The Security Password cannot be

changed and cannot be retrieved. If you wish to change

or remove the Security Password, the Account may be

cloned to remove the Security Password in the new

Account (see OI382 for more information about "cloning"

Accounts). To change or remove the Security Password in

the locks and/or the Gateways, each lock (or Gateway)

must be manually defaulted and re-downloaded with the

new (or blank) Security Password.

To set the Security Password, click Tools > Set Security

Password.

In the screen that appears (shown below), type a unique 6

character (no more, no less) password in the New

Password field. Retype the password in the Confirm field

and click OK to set the Security Password, or click Cancel

to exit without saving changes.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 11

"Gateway Configuration" Screen - Field and Button Definitions

The Gateway Configuration screen allows you to seek out new Gateway devices and add them to an Account. In addition,

the internal Gateway settings are configured from this screen, as well as other Gateway tools and actions. Equally

important, it is in this screen where locks are discovered and assigned to your Gateways.

Click the Gateway Config button to access the Gateway Configuration screen.

Discover Locks

Click to start the lock discovery

process. The signal will be

transmitted based upon the

number of locks selected in

"Number of Locks to Dis-

cover". Note: Only those locks

within range that have not al-

ready been assigned to a Gate-

way will respond.

Status

Displays the current state or the

last-known condition of the

Gateway.

Assigned Locks

Indicates the total number of

locks assigned to the selected

Gateway.

Close

Click to save changes and exit.

Firmware

Indicates the current firmware

version the Gateway is running.

MAC Address

A unique serial number assigned to the

Gateway that identifies that Gateway from

all others. Inside the Gateway housing,

the MAC address is located on a square

sticker (look under the bar code) and has

12 digits, grouped in 6 pairs separated by

dashes.

Ch No.

Displays the internal

channel number as-

signed to the Gateway.

IP Address

Specifies the IP address

currently assigned to the

Gateway from the network.

This column is color coded;

see "Color List" on the next

page.

Description

Default name is "New Gate-

way".

Double-click to manually edit

the Gateway Description.

Actions

Click to display the Actions

menu selections

Tools

Click to display the Tools

menu selections

Discover Gateways And Auto Add

This button combines two actions: The

"Discover New Gateway(s)" process

and the "Add Gateway To Account"

process, in one button.

The Gateways that are found on the

network (but not already configured) are

automatically added to the current

Account and listed below.

Number of Locks to Discover

Click to set the number of locks

you wish to discover (1 - 63).

12 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Things to Remember

1. IMPORTANT: Gateways must be on the same Subnet

as DL-Windows to allow for successful discovery.

Once Gateways are added to the

system, its static IP address,

Wireless settings, etc., may then

be configured. See Tools >

Configure/Edit Network Settings

for more information.

Discovering / Adding Gateways

Once connected to the network, Gateways must be

discovered and added to the Account. This can be

accomplished in one of 3 ways:

● In the Gateway Configuration screen, click the

Discover Gateways And Auto Add button. This one-

click option discovers and adds ALL "Available" (see

Color List below) Gateways to the selected Account.

● In the Gateway Configuration screen Actions menu,

click Discover New Gateway(s). This action will find

ALL "Available" Gateways and list them on the screen.

Note: The IP addresses of "Available" Gateway(s) will

be highlighted green (see color list below). The next

step is to click to select a Gateway you wish to add, then

click Actions > Add Gateway to Account. Click Yes in

the confirmation popup and when added, the IP address

of the Gateway will be highlighted in blue. This two-step

option allows you to first discover Gateways, then

selectively decide which Gateways to add.

● In the Gateway Configuration screen, click Tools >

Manually Add a Gateway. This option opens the

Manual Gateway Addition screen, where the MAC

Address of the Gateway is manually typed and saved to

the database. A connection will then be attempted to the

Gateway over the network, and if successful, the

Gateway will be added to the system. When Gateways

cannot be added to the system, it will be colored red.

See Color List below.

2. All added Gateways are put into Gateway Emergency

"GROUP A" by default. For more information, see

Automatic Gateway Grouping on page 38.

3. Since Gateways are discovered and added using

DHCP (Dynamic Host Configuration Protocol), and are

therefore not yet static, a reminder "red siren" symbol

will be displayed in the DL-Windows "Main Screen"

status bar upon Gateway addition. The "red siren"

symbol is a reminder that keypad-initiated Emergency

commands may not function correctly if the Gateway

has not been configured with a static IP address. See

38 for important information.

Color List

The IP Address column is color coded, as follows:

● Blue: Gateway Status = Ready.

Indicates the Gateway has been discovered on the

network successfully, and added to an existing Account

within DL-Windows. Note: This Gateway may or may

not have physical locks assigned (may or may not have

a Lock Table assigned).

● Green: Gateway Status = Available.

Indicates a Gateway has been successfully discovered

on the network, but has not been added to the Account

within DL-Windows.

● Red:

Gateway Status = Unreachable.

Indicates a Gateway that has been previously

discovered and added to an Account, but is currently

not reachable on the network. Note: Gateway can be

re-located by clicking Actions > Relocate Gateways

Displayed in Red. This red color can signify a security

mismatch, detailed below.

OR

Red:

Gateway Status = Security Mismatch.

Indicates the Gateway Security Password and the

Security Password set for the Account are not the

same, therefore a successful connection cannot be

established. Note: Gateway may require latest

configuration data. See page 22 ("Tools > Send Lock

Config Table to the Gateway") and the TIP on page

28 (the page for "Gateway Configuration > Actions >

Relocate Gateways (Displayed in red)") for more

information.

For a Gateway to be considered

"Available", it must be on the network, have a

dynamically obtained IP address, and manually

reset (see WI2085 for reset GW procedure). A

Gateway may also be considered "Available" if it

already contains the same Security Password as the

Security Password set for the Account. See section

Tools> Import Gateway and Assign Lock(s) for more

information.

TIP

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 13

Discovering / Assigning Wireless Locks

After Gateways have been discovered and added to the

Account, physical locks may now be discovered and

assigned to the Gateways. More commonly, this is

accomplished in two steps: First discovering the locks, then

assigning them to the Gateway(s).

Note: After lock discovery and lock assignment to a

Gateway, locks are then "Linked" to Lock Profiles.

Therefore, before proceeding, we recommend that you

create Lock Profiles for each physical lock you wish to

assign to a Gateway.

DISCOVERING LOCKS

The lock "discovery" process (search) can be performed in

one of two ways:

● In the Gateway Configuration screen, click to select the

desired Gateway to which the installed lock will be

assigned. Then in the Number of Locks to Discover

pull-down, select the number of physical locks you wish

to attempt to discover, then click Discover Locks.

Note: The selected Gateway will transmit the discovery

request radio signal to the locks in the vicinity. Only those

locks within range that have not already been assigned to a

Gateway will respond. By selecting the number of physical

locks to be discovered, the discovery process will stop the

instant the selected number of locks are found. If the

number of locks selected exceeds the number of

unassigned locks that exist in the vicinity, the discovery

process will continue for a maximum of one minute. The

discovery process may also be stopped at any time by

clicking the Abort button (this will also return the list of

locks found up until the time the Abort button was clicked).

● This second procedure is identical to the above

procedure, except the lock discovery process is started

using Actions > Discover Locks.

ASSIGNING LOCKS

After locks are discovered, the following Discovered Locks

popup automatically appears listing the successfully

discovered locks for the selected Gateway:

Click to add a check to the checkbox next to the serial

number for each lock you wish to assign to the selected

Gateway, then click Assign. The following message

appears as locks are assigned:

After locks are assigned to the selected Gateway, the

following popup appears to begin the required procedure of

"Linking" the assigned locks to Lock Profiles. See the next

section for procedures.

MANUAL LOCK ASSIGNMENT

In the Gateway Configuration screen, click Tools >

Manually Add a Lock to the Gateway. In the screen that

appears, type the lock serial number and select the lock

model from the Lock Type pull-down. Then click Add Lock.

This feature adds the lock(s) to the database; when finished

adding locks, click Tools > Send Lock Config Table to the

Gateway. All locks in the database will then attempt to be

assigned to the Gateway. For more information with using

this feature, see 21.

The discovered locks displayed in the screen above are those physical

locks that were able to be discovered based on their range to the

selected Gateway. (For more information about signal levels, see page

46 for definitions of GTW Rx and LCK Rx).

For a lock to be considered "unassigned"

to a Gateway, it must be manually reset

("defaulted"). See the programming instructions

that came with the lock for the reset procedure.

TIP

If a lock(s) fails to be assigned to

the Gateway, reattempt the lock

assignment by clicking Tools > Send

Lock Config Table to the Gateway.

TIP

14 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Linking Lock Profiles

After physical locks are successfully assigned to the Gateway, they must be "Linked" to Lock Profiles (locks not Linked

cannot be downloaded). In DL-Windows, the word "Link" is used to describe the specific action of associating a Lock

Profile to the physical lock assigned to the Gateway (by serial number). The Lock Type (model) of the Lock Profile MUST

match the assigned lock to which you wish to Link. The Link / Unlink Lock Profiles screen may be accessed in one of two

ways:

● More commonly, the screen is accessed immediately following lock assignment (click Yes to confirmation popup shown

on previous page);

or

● At a later time, from the DL-Windows "Main Screen", click Tools > Link / Unlink Lock Profiles.

Note: A condensed version of the screen may be accessed via the right-click options from the Lock Profile (right-click the

Lock Profile and select "Link / Unlink Lock Profile"). See page 47 for more information.

LINKING PROCEDURE

To Link a Lock Profile to an assigned lock, in the Available Lock Profiles field, click to select a Lock Profile, then in the

Available Locks By Serial Number field, click the physical lock to which you want to Link. The pair will automatically

move down to the Linked Locks grid at the bottom. Note: Since Lock Types (models) must match for successful Linking,

when a Lock Profile is selected, the Available Locks By Serial Number field automatically filters and displays only

matching Lock Types.

If an incorrect Linking was made, or if you wish to undo a Linking, simply select the Linked lock from the Linked Locks grid

and click the Unlink Lock button (the Lock Profile and the available locks will return to their respective lists, and are

thereafter available for Linking.

CONGRATULATIONS! Your locks have been Linked, and are now able to be downloaded with Lock Profile data. To add

Users, Schedules, etc., see OI382.

Unlink Lock

Unlinks the selected Lock Profile.

Available Locks By Serial Number

Displays the physical lock serial

number; the Lock Type (model), the

Gateway name and the IP address to

which the physical lock is assigned.

Available Lock Profiles

Displays all existing available Lock

Profiles in the current Account.

Linked Locks

Lists the physical locks currently

Linked to Lock Profiles.

Close

Click to save changes and exit.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 15

Description

Displays the text of the Description field from the Gateway

Configuration screen. Default = "New Gateway".

IP Address

Displays the network address currently assigned to the

Gateway.

Firmware Version

Displays the current firmware edition (or "release") the

Gateway is running.

Firmware Update

Indicates the result of the last Gateway firmware upgrade

process. "Good" signifies that the last firmware upgrade was

completed without errors. "Bad" signifies the last firmware

upgrade was completed unsuccessfully. See Tools >

Update Gateway Firmware on page 20 for more

information.

Security Code ("Security Password")

Indicates the status of the Security Password by comparing

the Security Password in the Gateway with the Security

Password in DL-Windows. If Passwords are not identical,

the field indicates "Security Mismatch", thus disabling DL-

Windows-to-Gateway communications.

Lock Communication Error

Indicates if locks assigned to the selected Gateway

previously failed to communicate with that Gateway.

If "Communication Error" appears in this field, a lock

communication failure was detected. Click Tools > View

Gateway's Lock Table to determine which lock failed to

communicate.

Status

Displays the current state (or condition) of the Gateway.

Indicates either "Normal" to indicate a normal condition;

"Emergency Lock Down" if an Emergency Lock Down

Command was sent; and "Emergency Passage" if an

Emergency Passage Command was sent.

Last Updated

Displays the date and time of the latest Gateway status

update (the last time the Gateway Status was retrieved).

Update (button)

Click to request an updated Gateway status from the

Gateway. All fields will be refreshed upon Gateway status

retrieval.

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Tools > View Gateway

Status. Upon selection, the Gateway Status is retrieved and displays the operational status of the selected Gateway.

Gateway Configuration > Tools > View Gateway Status

16 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Tools > View Gateway's

Lock Table. Upon selection, the Gateway's internal "Lock Table" is displayed, showing each lock assigned to the selected

Gateway, and their status as of the last time the table was updated (date and time shown at bottom left). Use this screen as

a tool to verify successful communication with your locks, and their configuration status. Click Refresh to retrieve and dis-

play the latest information.

Lock Profile

Displays name of the Lock Profile Linked to the physical

lock assigned to the Gateway. If not Linked to a Gateway,

the text reads "Not Linked".

Serial Number

Displays the lock's unique number assigned and

programmed into the lock firmware at the factory. Each

Networx lock is identified in the system by this unique serial

number.

Lock Type

Specifies the model of the Trilogy Networx series locking

devices, such as "PDL6100", "DL6100" or "PL6100".

Firmware

Indicates the firmware source code edition currently

residing in each physical lock.

Status

Indicates whether the physical lock is currently "assigned"

to the Gateway (was successfully added and configured) or

"Unable to Configure" (failed to be added and assigned to

the Gateway).

Lock Status

Indicates the latest condition of the physical lock (i.e.

"Locked", "Passage", etc.). If status is unknown or unable

to be retrieved, "Communication Error" will be displayed.

Signal

Indicates the radio transmission strength, as measured

between the Gateway to the physical lock (GTW Rx). A

higher number indicates stronger signal.

Battery

Displays the status of the battery powering each physical

lock.

Refresh (button)

Click to retrieve and update the contents of this Gateway

Lock Table screen.

Gateway Configuration > Tools > View Gateway's Lock Table

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 17

Lock Information

Displays Lock ID number and Lock Profile name. If not

Linked to a Gateway, "Not Linked" is displayed.

Serial Number

Displays the physical lock's unique serial number assigned

and programmed into the lock firmware at the factory.

Each Networx lock is identified in the system by this unique

serial number.

Lock Type

Specifies the model of the Trilogy Networx series locking

devices, such as "PDL6100", "DL6100" or "PL6100".

Gateway

Displays the IP address of each Gateway in the Account to

which the lock is assigned.

Delete (button)

Click to send a delete command to the Gateway and to the

selected (checked) physical locks.

Unresponsive Lock(s)

If some locks could not be reached and therefore could not

receive the delete command, although the locks will be

removed from the Gateway Lock Table (see previous

page), each lock should be manually reset ("defaulted") to

remove their lock assignments (thus allowing for re-

discovery). See the programming instructions that came

with the lock for the reset procedure.

In the Gateway Configuration screen, click Tools > Delete Lock(s) by Serial Number(s). Upon selection, a table dis-

playing all physical locks discovered by all Gateways in the Account is displayed. Multiple locks can be removed from multi-

ple Gateways by checking their respective checkboxes and clicking Delete. Note: The removal command is first sent to

the Gateway, then is sent to each selected physical lock to break the relationship between them. Once removed, the lock

becomes unassigned and thus able to be re-discovered.

Unresponsive Gateway(s)

If some Gateways could not be reached and therefore

could not receive the delete command, the selected locks

will be removed from the DL-Windows Gateway database.

The Gateway will be updated later when the Gateway

connection is re-established.

Note: Since the Gateway could not be reached, the

selected locks could not be reached either. Therefore,

although the selected locks will be removed from the

Gateway Lock Table (see previous page), these locks

should be manually reset ("defaulted") to remove their lock

assignments. See the programming instructions that

came with the lock for the reset procedure. .

Gateway Configuration > Tools > Delete Lock(s) by Serial Number(s)

18 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Tools > Configure / Edit Network Set-

tings. Upon selection, the Network Configuration screen will open, allowing for Gateway network settings to be configured or edited.

This screen is typically used to configure the Gateway with a static IP address, configure for "Internet Gateway Connectivity" (Remote

Configuration settings) and/or wireless Gateway configuration. Important: For more information about configuring your Gateway with a

static IP address, "Internet Gateway Connectivity" (Remote Configuration settings), and/or Wireless Network Configuration, see

WI2085.

The following is a brief description of each field as it applies to DL-Windows; see your network administrator for more information if needed.

Port (Remote Configuration area)

Default = 10001. Identifies the default Gateway communication

port setting.

Gateway Configuration > Tools > Configure / Edit Network Settings

IP Address Setup

Wireless Mode

Configures the selected Gateway for either wireless or wired

communication with the computer network. Select either Wired

Only or Wireless Only from this pull-down menu. If Wireless

Only is selected, the Wireless Network Security area and the

Wireless Network Configuration area both become active and

available for selection.

DHCP Name

To aid in locating the Gateway on the network, specify a name to

describe the domain name and hostname of the corresponding IP

address assigned to the selected Gateway. The DHCP Name

entered here will be used for the DNS configuration (default =

ALARMLCK).

Use DHCP (checkbox)

Use DHCP (Dynamic Host Configuration Protocol) is checked

(enabled) by default. When checked, DL-Windows allows the

selected Gateway to accept the dynamic assignment of an IP

address by the TCP/IP network. Note that Emergency Commands

may NOT function properly using DHCP. Uncheck Use DHCP to

allow the manual assignment of a static IP address to the selected

Gateway (a warning popup appears that the Gateway may be

unreachable until it is installed on the correct network). The IP

Address, Subnet Mask and Default Gateway fields become

active. Un-checking Use DHCP also activates the fields in the

Remote Configuration area for "Internet Gateway Connectivity"

support (though not required unless using for Internet access).

IP Address

This field allows the (static) IP address to be manually assigned to

the selected Gateway.

Subnet Mask

The IP protocol makes use of a Subnet Mask to more efficiently

route packets to their correct network destinations.

Default Gateway

This field is the IP address of the physical device, such as a router,

for the current subnet to which you want to be connected. This field

is not to be confused with the IP address of the Alarm Lock

Gateway device installed in the system.

Gateway MAC Address

This field represents the unique 12-digit MAC Address of the

Gateway. This field cannot be edited or changed.

WAN Address (Remote Configuration area)

This field allows DL-Windows to communicate with a Gateway over

a Wide Area Network (Internet).

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 19

When WPA2 Security Type is selected, the options for the

selected Gateway are:

● CCMP: (Counter Mode with Cipher Block Chaining Message

Authentication Code Protocol) improves upon both WPA and

TKIP. CCMP is a required option for Robust Security Network

(RSN) compliant networks.

● TKIP: See above.

Key Type

A "key" is a numeric code used to encrypt data, and is used to

secure the data traffic between the router and the Gateways. The

key "type" can be "Passphrase" or "Hex" (a hexadecimal string,

for example, '45D3 E454 3523 EDC2'). To ease encryption key

entry, a password or passphrase can be entered instead of the

cryptic hexadecimal characters.

Key

Retype Key

Type your key in the Key field, and re-type in the Retype Key field

to confirm it. Maximum character entry dependant upon

selections made above.

Wireless Network Configuration

Network Name (SSID)

This field allows you to specify the SSID (Service Set IDentifier)

name assigned to the wireless Wi-Fi (802.11) network. Wireless

Gateway models in a system must use this name to allow for

network communication. Note: This field is case-sensitive and

can be up to 32 bytes in length.

Network Type

Click the pull-down menu to select the network communication

mode. With "Infrastructure" selected, the Gateways

communicate to a wired LAN via access points. With "Ad Hoc"

selected, the Gateways can communicate directly in a peer-to-

peer fashion.

Channel Number

Click the pull-down menu to manually specify the number (1 - 11)

of the carrier frequency (subchannel pathway) between the

selected Gateway and the wireless Wi-Fi (802.11) network.

Save (button)

Click to record all network configuration data to the database. Use

this option when connection to the Gateway failed due to incorrect

network configuration entry. Note: Network configuration data

will not be sent to the Gateway.

Send (button)

Click to save all network configuration data to the database and

send all network configuration data to the Gateway.

Close (button)

Click "X" or the Close button to exit the screen without saving

changes.

Wireless Network Security

Security Type

Click the pull-down menu to specify the 802.11 security protocol

(encryption method) to be used when the selected Gateway is

connected to the wireless network. The selections are:

● WEP (Wired Equivalent Privacy) The WEP encryption method

was designed to provide wireless networks with the

"equivalent" security available in traditional wired "landline"

networks.

● WPA (Wi-Fi Protected Access) A security protocol from the

Wi-Fi alliance for 802.11 wireless networks. It uses the

Temporal Key Integrity Protocol (TKIP) to provide stronger

encryption than the earlier WEP (Wired Equivalent Privacy)

method. Derived from, and a subset of, the IEEE 802.11i

security standard, WPA includes 802.1x authentication.

● WPA2 (Wi-Fi Protected Access 2) Supports additional security

features of the IEEE 802.11i standard that are not already

included in the WPA security protocol.

Note: For each Security Type selected, different choices appear

for the other fields in the Wireless Network Security area of this

screen.

Authentication

Click the pull-down menu to specify the 802.11 authentication

protocol to be used when the selected Gateway is connected to

the wireless network. When WEP Security Type is selected, the

options for the selected Gateway are:

● Open/None: Requires no Authentication for the data

transmissions between the selected Gateway and the router.

● Shared: Requires a shared symmetric code (encryption "key")

for all data transmissions between the router and the Gateway.

When WPA or WPA2 Security Type is selected, the option is:

● Pre-Shared Key (PSK): Allows the use of manually-entered

keys or passwords (encryption "key") to initiate WPA security.

Encryption

The reversible transformation of data from its original format into a

concealed format as a process for securing its accessibility,

authenticity and integrity. Encryption uses an encryption algorithm

(sequence) and one or more encryption keys (numeric codes).

When WEP Security Type is selected, the options for the

selected Gateway are:

● 64 bits: Although the 64-bit WEP data encryption method

uses a five-character key size (forty bits or five bytes) for

symmetric encryption, plus an additional 24 factory-set bits,

this method represents a relatively low level of security.

● 128 bits: Stronger than 64-bit WEP, 128-bit WEP uses a

string of 26 hexadecimal characters (0-9 and A-F), each

representing four bits of the key.

When WPA Security Type is selected, the option for the selected

Gateway is:

● TKIP: (Temporal Key Integrity Protocol), a security protocol

algorithm that compliments WPA encryption with increased

security measures such as extended key lengths and data

integrity checks.

20 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, click Tools > Ping Gateway.

Upon selection, a Ping (Packet INternet Groper) command will test whether the IP address of the Gateway is reachable on

the network. Ping sends a packet out on the network and waits for a response; the result of the ping is indicated by a

splash screen on the DL-Windows "Main Screen". A successful test displays the IP address of the Gateway with the word

"found"; an unsuccessful test displays the IP address of the Gateway with the words "not found".

Upon selection, the standard Windows Open dialog box

appears (shown at right), allowing you to browse for the

binary ".bin" file containing the Gateway firmware update.

Select Gateway firmware file, then click Open to initiate

the update process.

The system will check the integrity of the firmware, burn it

into the Gateway memory, reboot the Gateway and verify

if the Gateway is functioning properly. Upon completion,

a Gateway Status screen will automatically open. Verify

that the Firmware Update field is green, reads "Good",

and the Gateway firmware version has been updated in

the Firmware Version field.

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Tools > Update Gateway

Firmware.

Gateway Configuration > Tools > Ping Gateway

Gateway Configuration > Tools > Update Gateway Firmware

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 21

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Tools > Manually Add a

Lock to the Gateway. Upon selection, the Add Lock Serial Number screen opens, where you can manually assign a

specific lock serial number(s) to a selected Gateway.

This screen is typically used to assign multiple locks to a Gateway without needing to perform the discovery process.

Manually type the serial number(s) of the lock(s) and select their corresponding models from the Lock Type pull-down,

then click Add Lock. Each lock, in succession, will be entered into the Gateway Table. When finished adding locks, you

must manually send the Gateway Configuration Table to the Gateway by clicking Tools > Send Lock Config Table to the

Gateway. Note: Remember to Link your locks after sending the Gateway Configuration Table.

Serial Number

Carefully type the lock's unique 8-character factory serial

number located on the lock housing (each Networx lock is

identified in DL-Windows by this unique number). Type all

characters of the serial number, do NOT include dashes

or spaces.

Lock Type

Click the Lock Type pull-down and select the

corresponding wireless lock model ("DL6100", "PDL6100",

etc.).

Add Lock (button)

Click to manually add the lock to the Gateway (Serial

Number plus Lock Type). The following message will

display:

Gateway Configuration > Tools > Manually Add a Lock to the Gateway

~ LOCK ID CARD ~

LOCK MODEL _________________________________

FACTORY SERIAL NUMBER _______________________

INSTALLED LOCATION ___________________________

__________________________________________

When installing lock, please fill in all information on

this card. This information will be used when

adding network locks to DL Windows. Keep this

card in a safe place. Do not discard!

OI353 10/08

ALARM LOCK

We recommend that when installing the

lock on the door, a yellow-colored "LOCK

ID CARD" (see image below) be completed.

These yellow cards are a useful way to organize

lock information, including lock serial numbers.

TIP

22 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, click Tools > Send Lock Config Table to the Gateway. Upon selection, the Gate-

way will be updated with the latest configuration data and will attempt to assign locks (if necessary).

In DL-Windows, the word "configure" has a specific meaning--to "configure" is to "assign" discovered physical locks to a

Gateway, thus ensuring a fixed wireless communication channel exists between selected physical locks and a selected

Gateway.

The Gateway sends "configuration data" in the form of a "Lock Configuration Table" to the selected locks. This

"configuration data" contains items (an internal lock designation, a specific radio channel and security data) that are all em-

bedded in the "Lock Configuration Table". The "configuration data" then instructs the physical lock(s) to communicate

ONLY with that Gateway, thus preventing other Gateways from communicating with the physical lock(s).

Although other applications exist, the three most common uses for sending the Lock Configuration Table to a Gateway are:

● Assignment Retry - Lock was successfully discovered, but was unable to be assigned to the Gateway.

● Completing Manual Lock Addition - Requirement after manually assigning locks to the Gateway database.

● Security Mismatch - "Gateway Configuration Data" area elements do not match those elements within the DL-

Windows database.

Gateway Configuration > Tools > Send Lock Config Table to the Gateway

Gateway Configuration > Tools > Set Emergency Groups

In the Gateway Configuration screen, click Tools > Set Emergency Groups.

For information about setting Emergency Grouping, see the section "Using Emergency Commands" on page 38.

Gateway Configuration > Tools > Import Assigned Lock

In the Gateway Configuration screen, click to highlight a Gateway, then click Tools > Import Assigned Lock. Upon se-

lection, the Gateway Lock Table for the Account will be updated with data from the Gateway. Locks that are assigned to

the Gateway that are not in the Gateway Lock Table (in the DL-Windows database) will be imported / added to the DL-

Windows database. Though rare, this feature is typically used when a DL-Windows database has been corrupted, and

therefore requires an update from the Gateway.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 23

In the Gateway Configuration screen, after using the Discover New Gateways feature, select an "Available" Gateway,

then click Tools > Import Gateway and Assigned Locks. This feature is used to rebuild a DL-Windows database by im-

porting existing Gateway and lock configuration data.

When the Account information stored in DL-Windows is lost

(such as with a stolen laptop)--AND--the DL-Windows

backup files are either non-existent, inadequate or lost, the

above "Import" option can be used.

Once you have successfully re-created pertinent data

(Accounts, Lock Profiles, Global Users, etc.), the following

steps may be used to recreate your wireless system. Note:

To successfully restore your wireless system, you MUST

know the existing Security Password previously set for the

Gateway and locks.

1. In the DL-Windows "Main Screen", click Tools > Set

Security Password.

2. Type the Security Password that was previously set for

the Gateway and locks you wish to import (see page

10 for more information regarding Security Pass-

words).

3. Click the Gateway Config icon to open the Gateway

Configuration screen.

4. Click Actions > Discover New Gateways. The Gate-

way(s) appear in the Gateway Configuration screen

(IP address highlighted in green color; Status =

"Available").

IMPORTANT: Do NOT select Actions > Add Gate-

way to Account.

5. Click to highlight the Gateway you wish to import from

the list.

6. Click Tools > Import Gateway and Assigned Locks.

The Gateway will be added to the system and the lock con-

figuration table will be imported and written into the DL-

Windows database.

Gateway Configuration > Tools > Import Gateway and Assigned Locks

24 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, click Tools > Show WAN / Port Information. This feature expands the Gateway

Configuration screen to show the WAN Address column and Port column. To collapse these columns, click Tools > Hide

WAN / Port Information.

When using the "Internet Gateway Connectivity" support features (connection to the Gateway is made remotely over the

Internet), the WAN (Wide Area Network) Address and Gateway Port setting are required. These Remote Configuration

settings, previously set in the Network Configuration screen, are not automatically displayed in the Gateway Configura-

tion screen. Therefore you must click Tools > Show WAN / Port Information to view your connection status. See Color

List on page 12 for more information about Gateway connection conditions. For more information about setting the

"Internet Gateway Connectivity" support features, see "Configure / Edit Network Settings on page 18 and WI2085.

Network Adapter Selection

Click the pull-down menu to select the network card used by

the computer.

Click OK to save the selection or Cancel to exit without

saving. Note: Clicking OK in this screen saves the

selection only for the duration of the current DL-Windows

session. Quitting and restarting DL-Windows may require

re-opening this screen and re-selecting the network adapter.

Note: If the network adapter settings change when the DL-

Windows program is running, DL-Windows may require you

to close and re-open the program.

Gateway Configuration > Tools > Show WAN / Port Information

Gateway Configuration > Tools > Select Network Adapter

In the Gateway Configuration screen, click Tools > Select Network Adapter. This feature may also be accessed from

the DL-Windows "Main Screen", click Tools > Select Network Adapter. Note: If only one network adapter is detected,

these options will be unavailable.

The Network Adapter Selection screen allows you to identify and select the "network interface card" (NIC) you are using

inside your computer to communicate with the Gateway devices in your system. Some computers have the network

adapter built into the motherboard, thus precluding the need to make a selection (network adapter is automatically de-

tected). Other computers may use external network adapters (i.e. a USB network adapter). When both are a present, the

Network Adapter Selection screen may automatically appear when opening the Gateway Configuration screen, thus

requiring the selection of the desired network adapter. Remember, the router or corporate Ethernet network is connected to

an Ethernet adapter with an Ethernet cable (RJ-45 plug).

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 25

Gateway MAC Address

Carefully type the Gateway's unique 12-character factory

MAC Address located on the square sticker under the bar

code. Each Networx Gateway is identified in DL-Windows by

this unique number. Type all characters of the MAC

Address, do not include dashes or spaces. Note: The

Save button will be enabled after 12 characters are typed.

Save (button)

Click to manually add the Gateway into the DL-Windows

database. A connection will be attempted and if

successful, the Gateway will be ready for use.

In the Gateway Configuration screen, click Tools > Manually Add a Gateway. Upon selection, the Manual Gateway

Addition screen opens, where you can manually add a Gateway by adding its unique MAC address.

This screen is typically used to add a Gateway to an Account without needing to perform the Gateway discovery process.

Manually type the unique MAC address of the Gateway in the Gateway MAC Address field, then click Save. The Gateway

MAC address will be saved to the database and added to the Account, and a connection to the Gateway will be attempted.

If the Gateway connection is established successfully, the IP address will be highlighted blue (if unsuccessful, it will be high-

lighted red). When manually adding a Gateway to an Account, keep in mind the following:

● The Gateway you wish to manually add to the Account must be on the network and "Available" (dynamically obtained

IP address and manually reset). See WI2085 for more information.

● The Gateway must be successfully saved and added to the Account before configuring a static IP address or wireless

settings.

● When using the "Internet Gateway Connectivity" feature, uncheck Use DHCP and type the required Remote Con-

figuration settings (WAN Address and Port). See WI2085.

Gateway Configuration > Tools > Manually Add a Gateway

For a Gateway to be considered "Available", it must be on the network, have a dynamically

obtained IP address, and manually reset (see WI2085 for reset Gateway procedures). A Gateway

may also be considered "Available" if it already contains the same Security Password as the Security

Password set for the Account. See section Tools> Import Gateway and Assign Lock(s) for more

information.

TIP

~ GATEWAY ID CARD ~

GATEWAY MODEL ________________________________

MAC ADDRESS __________________________________

INSTALLED LOCATION _____________________________

____________________________________________

When installing the Gateway, please fill in all infor-

mation on this card. This information will be used

when adding Gateway devices to DL Windows.

Keep this card in a safe place. Do not discard!

ALARM LOCK

OI357 2/09

We recommend that when installing a

Gateway, a blue-colored "GATEWAY ID

CARD" (see image below) be completed.

These blue cards are a useful way to

organize Gateway information, including the

MAC Address and physical location of the Gateway.

TIP

26 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, after using the Discover New Gateways feature, select an "Available" Gateway,

then click Actions > Add Gateway to Account. A confirmation popup appears:

Click Yes in the confirmation popup to complete the Gateway addition. Note: This action is used when adding newly dis-

covered ("Available") Gateways to the Account (Gateway IP address highlighted in green). See page 12 for more informa-

tion about Discovering / Adding Gateways.

Gateway Configuration > Actions > Add Gateway to Account

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Actions > Remove Gate-

way from Account. Before the Gateway can be removed from the Account, any locks already assigned to the selected

Gateway must first be deleted ("un-assigned") from that Gateway. If all locks have already been deleted from the Gateway,

or if there are no locks assigned to the Gateway, upon selection, and after confirmation, the Gateway will be deleted from

the Account.

For more information regarding removing locks, see page

17.

Gateway Configuration > Actions > Remove Gateway from Account

Confirmation Popup

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 27

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Actions > Locate All

Locks on Gateway. Upon selection, the Locate Time screen opens (shown below) where you can set the duration of time

(in seconds) for all locks assigned to the selected Gateway to beep and flash their red LEDs. This option is typically used

when you wish to find all of the physical locks or to confirm the wireless connection is operational. Note: Locks may be located

even if they are not Linked to a Lock Profile.

Locate Time in Seconds

Click the pull-down menu to select the time in seconds.

during which all wireless locks assigned to the selected

Gateway will beep and flash their red LEDs. Up to 255

seconds (4 minutes 15 seconds) can be selected; default

duration is 30 seconds.

OK (button)

Click OK and all wireless locks assigned to the selected

Gateway will beep and flash their red LEDs for the

selected Locate Time duration.

Gateway Configuration > Actions > Locate All Locks on Gateway

Cancel

Click to exit without requesting the locate action.

Note: Individual locks may be located (beep and flash

their red LEDs) via a right-click option from the Account

List area (see "Locate Lock" on page 48).

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Actions > Discover

Locks. This option is identical in operation to the Discover Locks button found in the Gateway Configuration screen.

See page 13 for more information about discovering wireless locks.

Gateway Configuration > Actions > Discover Locks

In the Gateway Configuration screen, click Actions > Discover New Gateways. Upon selection, an attempt is made to

discover all new Gateway devices on the network. Gateways that are not yet added and are therefore "Available" will be

listed in the Gateway Configuration screen with the IP address highlighted in green. This option is used when using the

two-step approach indicated in the Discovering / Adding Gateways section on page 12 of this manual. In addition, this

option may be used to rebuild a database by importing an existing Gateway and its lock configuration data (see page 23,

Tools > Import Gateway and Assigned Locks).

Gateway Configuration > Actions > Discover New Gateways

28 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

A configured Gateway (discovered on the network, added

to an Account and operational) is listed in the Gateway

Configuration screen with its IP address highlighted blue

(Status = "Ready"). When a configured Gateway has sub-

sequently lost communication with the network and the

Gateway Configuration screen is opened, the Gateways

IP address will be highlighted red (Status =

"Unreachable").

If a Gateway(s) is unreachable with its IP address high-

lighted red, by clicking Actions > Relocate Gateways

(Displayed in red), an attempt is made to re-connect with

that Gateway(s).

If a Gateway IP address is highlighted in red, and therefore

a connection could not be established, try the following:

1. Check the network. Re-fresh the Gateway Configu-

ration screen (by closing and re-opening the screen).

If other Gateways exist in the Account and are listed

highlighted in blue, this indicates that part of the net-

work is still operational. You may need to contact your

network administrator to assist in finding the source of

the network problem.

2. Check your physical connections to the Gateway.

● The RJ-45 socket on the Gateway contains two

LEDs; the green LED should be lit continually when

the RJ-45 plug is inserted and properly connected.

The yellow LED flickers when data is being send to

or from the Gateway. If these two LEDs are not

functioning, you can suspect the problem lies with

the RJ-45 cable or the network. Try replacing the

RJ-45 cable. Note: Both LEDs are not lit when

the Gateway is configured for wireless (802.11)

use.

● If the RJ-45 socket LEDs are operational, remove

the Gateway housing cover, power down and

power up the Gateway by removing and replacing

the power wires at the Gateway power terminals.

3. Check your network configuration settings. Click

Tools > Configure / Edit Network Settings. Edit any

fields that may be incorrect. Click Save to save the

changes to the database.

4. Replace the Gateway. If the network and the physi-

cal connections are found to be in working order, the

Gateway device itself may need to be replaced. Open

the Gateway housing cover on the new Gateway de-

vice (it may be helpful to make note of the new Gate-

way's MAC Address located on a square sticker (the

MAC Address is located under the bar code and has

12 digits, grouped in 6 pairs separated by dashes).

Disconnect the power wires and the RJ-45 plug from

the old Gateway and reconnect all wires to the new

Gateway. Continue with the Actions, Replace Gate-

way with New One procedures on the next page.

Note: Upon opening the Gateway Configuration

screen, connection to each configured Gateway is

verified before proceeding. If the Gateway cannot be

reached, the following message is displayed providing

the option to relocate the Gateway.

In the Gateway Configuration screen, click Actions > Relocate Gateways (Displayed in red). Upon selection, an at-

tempt is made to "relocate" (re-establish a connection) with all of the Gateways that have their IP addresses highlighted in

red (Status = "Unreachable"). Note: If Status = "Security Mismatch", see TIP below.

Gateway Configuration > Actions > Relocate Gateways (Displayed in red)

If the Status = "Security Mismatch",

the Security Password in the Gateway

does not match the Security Password in

DL-Windows. Try manually resetting the

Gateway (partial reset) then click Tools >

Send Lock Config Table to the Gateway.

See the instructions in WI2085 for resetting

the Gateway.

TIP

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 29

In the Gateway Configuration screen, click to highlight an "unreachable" (IP address highlighted red) Gateway in the list,

then click Actions > Replace Gateway with New One. Upon selection, the Gateway discovery process is started, and all

newly discovered Gateways will be listed in the New Gateways screen. Select the desired Gateway from the list, then click

OK. All existing Gateway configuration data (radio channel, security data, etc.) and the replaced Gateway's Lock Table

(existing assigned locks) will be sent to (and used by) the new Gateway. Note: Functional Gateways (Status = Ready; IP

address highlighted blue) may also be replaced, if desired.

This option is typically used when a working Gateway

(discovered on the network, added to an Account and op-

erational with physical locks assigned) becomes faulty and

needs to be physically replaced.

Before replacing the Gateway, be sure to check the net-

work and the Gateway connections outlined in the Actions,

Relocate Gateways (Displayed in red) on the previous

page.

Physically replace the Gateway device: Disconnect the

power wires and the RJ-45 plug from the old device, then

reconnect all wires to the new device. Remember to press

the "RESET" button on the new Gateway PC board to clear

the Gateway memory (see the instructions in WI2085 for

resetting the Gateway).

In the Gateway Configuration screen, click to select the

Gateway you wish to replace. Then click Actions > Re-

place Gateway with New One. The following screen ap-

pears showing newly discovered Gateways:

Gateway Configuration > Actions > Replace Gateway with New One

Click the radio button to select the desired Gateway and click

OK. DL-Windows will automatically replace the old Gateway

with the new Gateway, copying the Gateway configuration

data (radio channel, security data, etc.) and existing assigned

locks into the new Gateway.

30 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Gateway Configuration screen, click to highlight a specific Gateway in the list, then click Actions > Gateway Signal

Test Mode. Upon selection, the Gateway Signal Test screen opens (shown below) where you can set the duration of time

(minutes) the Gateway will continuously generate a signal to the AL-NSM Networx Signal Meter (required). For new and

existing installations, this option is used to perform a site survey test of the premises, to help you find the optimum location

for Gateways relative to the door locks, and to determine the optimum number of Gateways needed to cover the number of

locks you plan to install. IMPORTANT: This feature will only operate with Gateway firmware version 3.88 or later.

Gateway Configuration > Actions > Gateway Signal Test Mode

Test time in minutes

Click the pull-down menu to select the time (in minutes) the

Gateway will generate a signal to the AL-NSM (Networx

Signal Meter). 1 - 30 minutes can be selected (default is

30 minutes).

Start (button)

Click to initiate the test signal generation from the selected

Gateway to the AL-NSM (Networx Signal Meter), for the

time selected. Note: A countdown (time remaining) will

display (see image below right). Notice that the Start

button changes to an Abort button that can be clicked to

cancel the test signal generation.

Abort (button)

The Start button changes to this Abort button. Click Abort

to cancel the test signal generation to the AL-NSM

(Networx Signal Meter).

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 31

Communicating with Wireless Locks

Networx Communication Overview

Once your have discovered your Gateways, assigned your

locks and Linked them to Lock Profiles, there are several

methods for sending data to (or receiving data from)

wireless locks:

● Method 1: Communicate with wireless locks

individually using the Communication button on the

DL-Windows "Main Screen" (or from the Lock Data

screen);

● Method 2: Communicate with multiple wireless locks

(one after another) using the Wireless screen;

● Method 3: Communicate automatically at a specified

time using a Wireless Schedule screen action.

Note: Keypad programming of User Codes, Features,

Time Zones, and Schedules is available as a temporary

convenience to allow the lock to be put into use before

installing and configuring a wireless network. Therefore, all

lock programming added via the keypad cannot be

retrieved from the lock into DL-Windows. If you decide to

start programming your wireless lock via the keypad, we

recommend you keep hardcopy records (in a secure

location) of all Users, their User Codes, and any proximity

cards that may have been programmed. Keeping complete

and accurate records saves time because after the wireless

network is set up, any programming added via the keypad

must be re-added to DL-Windows and downloaded back to

the lock(s).

Method 1:

"Communicate with Selected Networx Lock"

1. In the DL-Windows "Main Screen", click the

Communication button on the toolbar and select

Communicate with Selected Networx Lock.

Note: The Communication button on the Lock Data

screen may also be used. In addition, if your lock has

not been Linked to a Lock Profile, the following popup

appears:

2. If Linked, the following screen appears:

Select any combination of data to send to your wireless

lock; a red circle with red square will denote those

selections made, though it is recommended to check

"Send/Receive All".

• Send/Receive All - Sends the complete program to

(and receives selected number of Event Logs from)

the wireless lock.

• Send Users - Sends all User Information including

User Enable / Disable status, User Codes (PINs),

proximity information, Group Assignments and

Emergency Users.

• Send Schedules - Sends all Schedules (see OI382

for more details).

• Send Features - Sends all Features chosen in the

Features screen (see Features section(s) in OI382

for more details).

• Send Date Time Update - Updates the wireless lock

with the PCs current date and time.

• Receive Number of Event Logs (pull-down) -

Receives the selected number of Event Logs from the

wireless lock (default = 50; maximum = 40,000).

3. Initiate the communication by clicking the Start button.

Note: Unlike standard non-wireless Trilogy locks,

wireless Networx locks do not need to be configured for

PC Program Mode (Function 58).

Any

combination

of available

data may be

sent to your

lock.

32 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

4. After data transfer has finished, verify all selected options

are displayed with a green checkmark and the message

"Communication completed" appears. Note: The

Event Log screen will automatically appear upon

successful communication if Receive Number of Event

Logs was previously selected:

Note: If data transfer fails, a circle with a red "X" will denote

communication error. Verify proper signal levels and check

network connections. For more information, see WI2085.

Method 2:

Communicate with Multiple Wireless Locks in

the Account

1. In the DL-Windows "Main Screen", click the Wireless

button on the toolbar.

The following screen appears.

Communicating with Wireless Locks (cont'd)

Note: See page 34 for detailed explanations of each

area of the Wireless screen. In addition, if your lock

has not been Linked to a Lock Profile, the entire row will

be highlighted red, and the Status column will indicate

"Not Linked" The lock must be Linked before you can

continue to the following steps.

2. For each wireless lock with which you want to

communicate, click to add a check to the checkbox in

the Enable column.

3. For each enabled lock, double-click its empty box in the

Function column, and click

the desired function in the

pull-down (as shown in the

accompanying image):

Note: To clear a function,

click the blank space above

Send Profile.

Once function is set, the Start button will be enabled.

Click Start to initiate communication to enabled wireless

locks. Note: The function set for each lock will be

performed; upon completion, the Status column for

each lock will denote the ending status of the

communication (i.e. Communication completed").

Method 3:

Automatically Communicate with Wireless

Locks

This method requires programming in the Wireless screen

and Wireless Schedules screen.

1. In the Wireless screen, create a Wireless

Configuration to be used for your wireless Schedule.

For each wireless lock you wish to communicate with

via a Schedule, click to add a check to the checkbox in

the Enable column and select the desired function from

the pull-down list.

Note: Additional Wireless Configurations may be

added with the "+ Add" button.

2. DO NOT click the Start button; close the Wireless

screen. The configuration(s) will be saved, and used in

the Wireless Schedules screen.

3. In the DL-Windows "Main Screen", click Wireless

Actions > Wireless Schedule. The Wireless

Schedule screen appears:

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 33

Note: See page 35 for detailed explanations of each

area of the Wireless Schedule screen.

4. Check the Enable checkbox for desired wireless

configurations. Note: Wireless Configurations were

pre-programmed in step 1.

5. For each enabled configuration, double-click the empty

box in the Time column to display the pull-down for HH /

MM / AM PM. Set desired time to initiate the intended

automatic communications.

6. Optional - Check the Repeat checkbox to program daily

automatic Schedules. Automatic wireless

communication will be performed every day at the

programmed time until the Repeat checkbox is

unchecked.

7. Click OK to save wireless Schedule programming.

Warning: If you have a Schedule programmed, and

DL-Windows is closed, the Schedule will not occur. A

warning popup appears (shown below) if you try to exit

DL-Windows with a schedule programmed:

Communicating with Wireless Locks (cont'd)

34 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

As described in Method 2 of the section Communicating with Wireless Locks (page 32) , the Wireless screen allows communi-

cation with individual or multiple wireless locks. The Wireless screen can be configured for various functions, as required. Func-

tions include Send Profile, Receive Log, and Send Profile & Receive Log.

Click the Wireless button to access the Wireless screen.

"Wireless" Screen - Field and Button Definitions

Right Click Menus

Enable (right-click menu)

To save time, right-click the "Enable" column; the desired action can be selected as follows:

● Select All: Adds a check to enable all (Linked) wireless locks.

● Unselect All: Removes a check from all (Linked) wireless locks.

● Select Highlighted: Adds a check to the Enable checkbox for all highlighted rows.

● Invert Highlighted: Removes a check from the Enable checkbox for all highlighted rows.

Function (right-click menu)

To save time, right-click the "Function" column; the desired action can be selected as follows:

● Change All to: "Receive Log"; "Send Profile"; "Send Profile & Receive Log": Selects function for all (Linked) wireless locks.

● Change Selected: "Receive Log"; "Send Profile"; "Send Profile & Receive Log": Selects function for all enabled wireless locks.

● Change Highlighted to…: "Receive Log"; "Send Profile"; "Send Profile & Receive Log": Selects function for all highlighted wireless locks.

Wireless Configuration (pull-down)

Click pull-down to select and display

wireless configurations (the selections

made in this screen will be saved as a

"Wireless Config").

Lock Information

Displays Lock ID, Lock Profile and Lock

Type (model) of the wireless lock. Note:

Non-wireless locks (i.e. PDL3000) will not

be displayed in this screen.

+ Add

Click to add additional

Wireless Configurations.

Clear

Click to clear the selected (checked)

Wireless Configuration. Note: Also

clears last-known communication

condition (see Status).

Delete

Click to remove the selected

Wireless Configuration.

Close (button)

Click to save settings and exit the screen.

Print

Click to open a "Print Preview" screen,

displaying all information in the Wireless

screen. Click the "Printer" icon to send

the request to your default printer.

Function (pull down)

Click to display a pull-down and select a function to

perform upon communication.

● Send Profile: Sends full lock program to the

wireless lock (Users, Schedules, Features, time/

date).

● Receive Log: Retrieves the Event Log (Audit

Trail) from the wireless lock.

● Send Profile & Receive Log: Combines the

above two functions.

See Right Click Menus below for programming

short cuts available.

Start

Click to initiate communications

to all enabled wireless locks.

Enable

When checked, upon communi-

cation, the Function pro-

grammed for the enabled wire-

less lock will be performed. See

Right Click Menus below for

programming short cuts avail-

able.

Status

Displays current state of the link

between the Gateway and the lock

("Linked" or "Not Linked"). Note:

"Not Linked" locks are highlighted

in red. This field also displays the

last-known lock communication

condition and is updated upon

subsequent communications.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 35

"Wireless Schedule" Screen - Field and Button Definitions

As described in Method #3 of the section Communicating with Wireless Locks (page 32), the Wireless Schedule screen

allows for automatic scheduled downloading of wireless locks. The Wireless Configuration created in the Wireless screen

is used to determine which wireless locks (and their respective pre-programmed functions) will automatically download at a

pre-designated time. After the scheduled download completes, the Wireless Schedule screen automatically opens to

allow the Status of each download to be verified.

In the DL-Windows "Main Screen", click Wireless Actions > Wireless Schedule.

Wireless Configuration

The "Wireless Configuration" created

in the Wireless screen (enabled locks

and pre-set functions).

Clear

Click to uncheck the Enable and Repeat

checkboxes, thus disabling the Schedule.

OK

Click to save the wireless schedule

programming and exit.

Enable

Add a check to enable the

Wireless Configuration, thus

activating the Schedule.

Time

Click to set the start time of the

scheduled communications from the

pull-downs (HH / MM / AM PM).

Repeat

Click to repeat the scheduled communica-

tion every day at the programmed time.

Leave unchecked for one-time scheduled

communication. Note: Daily automatic

communication may impact battery life.

Last Executed

Displays the date and time the

Schedule was last executed.

36 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Wireless Actions Menu

In the DL-Windows "Main Screen", click Wireless Actions:

Set Clock on All Locks

Based upon the current time and date of the PC running

DL-Windows, a command is sent to all Gateways to update

all locks with this current date and time. Note: Locks not

Linked will not receive this update command.

Emergency

Opens the Emergency Commands screen. For more

information about the Emergency Commands screen, see

page 37 and page 38.

Update Status of All Locks

A command is sent to all Gateways in the Account to

request the current status for all assigned wireless locks.

Status data received from each lock updates each

Gateways Lock Table. When the Lock Table of the

Gateway is subsequently viewed, the Table displays the

information as of the latest update request.

Note: To view the Gateway Lock Table, in the Gateway

Configuration screen, select Gateway, then click Tools >

View Gateway's Lock Table (see page 16).

Wireless Schedule

Opens the Wireless Schedule screen. Used for

programming automatic scheduled communication with

wireless lock(s). See page 35 for more information.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 37

The Emergency Commands screen allows for sending Emergency Commands ("Emergency Lock Down", "Emergency

Passage" and "Return to Normal") to Groups of Gateways in your system, thus sending the command to all locks assigned to

those Gateways. Note: All added Gateways are automatically placed into "GROUP A" by default; Gateways may be moved

to another Group via the Set Emergency Groups button. In addition, the Emergency Users List may also be viewed from

this screen.

Click the Emergency button to access the Emergency Commands screen.

The Emergency Commands screen may also be accessed in the DL-Windows "Main Screen" by clicking Wireless Actions

> Emergency.

"Emergency Commands" Screen - Field and Button Definitions

IMPORTANT: Before using the Emergency Commands screen, it is important to

read the next section regarding how to use Emergency Commands.

Emergency Groups

Select Group of Gateways to receive Emergency commands. Note: If only one

Gateway exists in the Account, the "GROUP A" checkbox will be checked and the

other checkboxes will be disabled. Note: The description of each Group (e.g.

"GROUP A") may be changed in the Set Emergency Groups screen.

GROUP A

(This Group selected by default).

Emergency Lock Down

Sends "Emergency Lock Down"

command to all Gateway(s) in the

selected Group(s).

Set Emergency Groups (button)

Click to open the Set Emergency Groups

screen, allowing for Gateway Group assign-

ment and setting the Gateway Group de-

scription text.

Emergency Passage

Sends "Emergency Passage"

command to all Gateway(s) in the

selected Group(s). Emergency Users (button)

Click to open the Emergency Users

screen, listing those Users allowed to

send Emergency commands.

Close

Saves the Emergency Group

selections and exits the screen.

Emergency Return to Normal

Sends "Return to Normal" com-

mand to all Gateway(s) in the

selected Group(s).

38 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

count, a "red siren" symbol appears at the bottom of the

DL-Windows "Main Screen" to serve as a reminder that the

added Gateway is configured with a changeable IP address

(DHCP). This "red siren" symbol will remain until all Gate-

ways in the Account are configured with a static IP address.

Configure Lock for Emergency Commands

All Networx locks are programmed at the factory to respond

to Emergency Commands from DL-Windows. However,

DL-Windows DOES allow you to program a specific lock (or

locks) to ignore Emergency Commands, if desired. In the

DL-Windows "Main Screen", click the Features button to

open the Features screen (Options tab), then un-check the

Lock Responds to Emergency Commands checkbox

(default is checked). Note: Keypad-initiated Emergency

Commands will NOT function until the Lock Profile has been

downloaded to the physical Networx lock.

Who can Initiate Emergency Commands?

● From DL-Windows: All Users, Administrators and

Operators have access to the Emergency Com-

mands screen, and therefore can initiate Emergency

Commands to any Gateway (and their assigned locks).

● From a Networx wireless lock keypad: Once the

Lock Profile has been downloaded to the physical lock,

Administrative Users 1 through 11 automatically have

the ability to initiate Emergency Commands from the

keypad. In addition, "non-Admin" Users (12+) may be

given the ability to initiate Emergency Commands from

the keypad by adding them to the Emergency Users

list (see next section).

Adding Emergency Users

To grant the ability of a "non-Admin" User (12+) to initi-

ate keypad Emergency Commands, in DL-Windows,

click the Global button to open the Global Users

Emergency Overview

Three "Emergency Commands" are available in the wireless

Trilogy Networx system:

• "Emergency Lock Down": Places all assigned locks

into an indefinitely locked state

• "Emergency Passage": Places all assigned locks into

an indefinitely unlocked state

• "Return to Normal": Reverts all assigned locks to the

state they were in prior to the initiation of the Emergency

command

These "Emergency" Commands can be initiated from DL-

Windows via the Emergency Commands screen, or at any

Networx wireless lock keypad. For more information re-

garding issuing Emergency Commands at the keypad, see

the programming instructions included with your lock. Note:

DL-Windows does not need to be running when issuing an

Emergency Command at the keypad.

WARNING: NEVER use Emergency Commands to "toggle"

Passage Mode, as this will severely impact battery life.

Getting Started

Automatic Gateway Grouping

("Emergency Grouping")

Upon the addition of each Gateway into an Account, the

Gateway is automatically placed into an Emergency Group

("GROUP A" by default). This is done so that upon the ini-

tiation of an Emergency Command, ALL Gateways in the

Emergency Group (and their assigned locks) will respond to

Emergency Commands issued from DL-Windows. In addi-

tion, the automatic placement of a new Gateway into an

Emergency Group allows for keypad-initiated Emergency

Commands, to lock down an entire system from a single

wireless lock.

Required Static IP Address

IMPORTANT: To ensure Gateways can respond to Emer-

gency Commands, all Gateways MUST be configured with

static (unchangeable) IP addresses. For more information

about configuring a Gateway with a static IP address, see

Gateway Configuration > Tools > Configure / Edit Net-

work Settings (page 18), and WI2085.

With the addition of each newly added Gateway to an Ac-

Using Emergency Commands

All Emergency Commands MUST be

tested weekly (or daily if necessary)

to ensure their correct operation.

WARNING

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 39

screen. Click to highlight a User(s) in the User Name

list, then right-click the User(s); from the menu that

appears, select "Allow User to Issue Emergency

Commands". In the Global Users screen User List,

a "red siren" symbol will display in the Name column

for those Users who can initiate Emergency Com-

mands. In addition, the Users will be added to the

Emergency Users list.

The Emergency Users list may be accessed from

Global Users > Administrative Users > Emergency

Users or from the DL-Windows "Main Screen" >

Emergency > Emergency Users. Existing Emer-

gency Users can be removed by selecting the User

and clicking the Remove button (or from the Global

Users screen, click to highlight the User(s), then right-

click and select from the menu Remove Emergency

User. The "red siren" symbol will be removed.

Who has Access during Emergency

Lock Down?

After a lock has been placed into the Emergency Lock

Down state:

● All Administrative Users (User Numbers 1-11) can still

unlock the physical lock.

● All Users added to the Emergency Users list (see

above) can unlock the physical lock.

IMPORTANT: Users disabled by a Schedule or by

any other means cannot initiate Emergency Com-

mands, even if they are added to the "Emergency

Users" list.

To enable access for all Users (including the Master

Code) during Emergency Lock Down: In the DL-

Windows "Main Screen", click the Features button to

open the Features screen (Options tab), then un-check

the Users are Disabled During Lock Down checkbox

(default is checked).

Using Emergency Commands (cont'd)

It may be helpful to refer to the

Terminology section in the DL-

Windows User's Guide (OI382) for

detailed descriptions of the terms

used in this section (i.e. User Code,

User Numbers, etc.).

TIP

40 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Selecting Emergency Lock Down sends a command to all Gateways (in the selected Gateway Groups) to immediately

lock all of their assigned wireless locks, thus securing the protected doors from unwarranted passage. In an Emergency

Lock Down state, all Administrative Users (User Numbers 1-11) can still unlock the physical lock. In addition, all Users

added to the Emergency Users list (see page 38) can unlock the physical lock.

From the Emergency Commands screen, click the Emergency Lock Down button.

The following Emergency View screen appears:

The following modes will be overridden by an Emergency

Lock Down Command :

● Normal mode ("non-Emergency")

● Emergency Passage mode

● Passage mode (via keypad Function 45)

● Scheduled Passage Mode (via "unlock" Schedule)

Note: Once in Emergency Lock Down, the wireless

physical lock(s) may be placed in Passage mode manually

(using keypad Function 48).

Emergency Lock Down Indication

● In DL-Windows: At the bottom of the DL-Windows

"Main Screen", a bar will flash from red to yellow with

the text "Emergency Lock Down" blinking continu-

ously until a subsequent "Return to Normal" command

is received (see image at the bottom of this page).

● At Physical Lock: Red LED blinks once every two

seconds.

IMPORTANT: Threats such as fire emergen-

cies, bomb threats or the release of hazard-

ous substances within a protected premises

may require an "Emergency Passage" Com-

mand to allow for a facility evacuation.

Other threats such as terrorist attacks, hostile

intruder situations, the outdoor release of

hazardous substances, tornado emergencies

and other life-threatening events, may require

an "Emergency Lock Down" - the opposite of

a facility evacuation.

It is strongly advised that all facilities develop

separate Emergency Lock Down and Emer-

gency Passage procedures appropriate for

the specific premises, and these Emergency

procedures be frequently practiced and con-

tinually refined.

Emergency > Emergency Lock Down

Once all locks assigned to the Gateway receive the selected Emergency Command, the status will return

"Emergency Lock Down" (highlighted red). In the above image, notice how the status of the second Gateway

displays "Unable to verify lock status" highlighted in yellow. This indicates that one or more locks assigned to

the Gateway may not have received the Emergency Command. Therefore, the Emergency View screen cannot

be closed and the Emergency Command will be continuously re-tried until the Abort Retries button is intentionally

clicked.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 41

Selecting Emergency Passage sends a command to all Gateways (in the selected Emergency Groups) to immediately

unlock all of their assigned wireless locks, thus un-securing the protected doors to allow passage. In an Emergency

Passage state, User credentials are no longer required to allow passage. Please use caution when using this feature,

and consider all implications of un-securing the protected doors.

From the Emergency Commands screen, click the Emergency Passage button.

The following Emergency View screen appears:

IMPORTANT: Threats such as fire emergencies,

bomb threats or the release of hazardous sub-

stances within a protected premises may require

an "Emergency Passage" Command to allow for a

facility evacuation.

Other threats such as terrorist attacks, hostile in-

truder situations, the outdoor release of hazardous

substances, tornado emergencies and other life-

threatening events, may require an "Emergency

Lock Down" - the opposite of a facility evacuation.

It is strongly advised that all facilities develop

separate Emergency Lock Down and Emergency

Passage procedures appropriate for the specific

premises, and these Emergency procedures be

frequently practiced and continually refined.

Emergency > Emergency Passage

Once all locks assigned to the Gateway receive the selected Emergency Command, the status will return

"Emergency Passage" (highlighted green). In the above image, notice how the status of the second Gateway

displays "Unable to verify lock status" highlighted in yellow. This indicates that one or more locks assigned to

the Gateway may not have received the Emergency Command. Therefore, the Emergency View screen

cannot be closed and the Emergency Command will be continuously re-tried until the Abort Retries button is

intentionally clicked.

The following modes will be overridden by an Emergency

Passage Command :

● Normal mode ("non-Emergency")

● Emergency Lock Down mode

● Locked mode (via keypad Function 46)

● Scheduled Locked Mode (via "lock" Schedule)

Note: Once in Emergency Passage, the wireless physical

lock(s) may be placed in Locked mode manually (using

keypad Function 49).

For areas that must remain secure, even in an Emer-

gency Passage state, we recommend de-selecting the fea-

ture "Lock Responds to Emergency Commands" in the

Features screen.

Emergency Passage Indication

● In DL-Windows: At the bottom of the DL-Windows

"Main Screen", a bar will flash from red to yellow with

the text "Emergency Passage" blinking continuously

until a subsequent "Return to Normal" command is re-

ceived (see image at the bottom of this page).

● At Physical Lock: Red LED blinks once every two

seconds.

42 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Selecting Emergency Return to Normal sends a command to all Gateways (in the selected Emergency Groups) to

immediately revert all assigned locks to the state they were in prior to the initiation of the Emergency command. For example. if

the lock was in an unlocked state due to a Schedule, and a subsequent Emergency Lock Down was initiated, the

Emergency Return to Normal command will revert the lock back to its original unlocked state.

From the Emergency Commands screen, click the Emergency Return to Normal button.

The following Emergency View screen appears:

Emergency > Emergency Return to Normal

Once all locks assigned to the Gateway receive the selected Emergency Command, the status will return

"Normal". In the above image, notice how the status of the second Gateway displays "Unable to verify lock

status" highlighted in yellow. This indicates that one or more locks assigned to the Gateway may not have

received the Emergency Command. Therefore, the Emergency View Screen cannot be closed and the

Emergency Command will be continuously re-tried until the Abort Retries button is intentionally clicked.

The following modes will be overridden by an Emergency

Return to Normal Command :

● Emergency Lock Down mode

● Emergency Passage mode

Warning: To not use Emergency Commands to "toggle"

Passage Mode, as it will severely impact battery life.

NEVER use Emergency Commands

to "toggle" Passage Mode, as this

will severely impact battery life.

WARNING

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 43

Emergency Commands > Set Emergency Groups

As mentioned in the previous section, each Gateway added to an Account is placed into Emergency "GROUP A" by

default. This is done to ensure that Gateways will communicate with each other in an Emergency, without the use of DL-

Windows (the Emergency initiated via the keypad). Note: Access to the Set Emergency Groups screen (from the

Emergency Command screen or from Gateway Configuration > Tools menu) is disabled when only one Gateway exists

in the Account.

In addition, Emergency Grouping is available to separate Gateways (and therefore their assigned locks) intentionally. For

example, to prevent a Gateway whose locks control a secure location from receiving an Emergency Command, place the

Gateway into "GROUP B"; thus the User may selectively decide via the Emergency Command screen, which Group(s) will

receive the Emergency Command.

It is also in the Set Emergency Groups screen where you may configure the individual description text reflected in the

Emergency Command screen of the Emergency Group (replacing "GROUP A" with another description).

In the Emergency Command screen, click the Set Emergency Groups button to open the

Set Emergency Groups screen. The Set Emergency Groups screen may also be

accessed from Gateway Configuration > Tools > Set Emergency Groups.

Prerequisite

The following message appears any time the Set

Emergency Groups screen is accessed:

How it Works

When an Emergency Command is initiated from a keypad,

the Command is disseminated to all Gateways, and their

locks, in the Account. See diagram at right. To allow

The diagram above illustrates how Emergency Commands

are distributed: Initiating an Emergency Command at the

lock keypad causes the keypad to send the Emergency

Command to its associated Gateway (named "Gateway 1").

"Gateway 1" then sends the Emergency Command to all

locks assigned to "Gateway 1". "Gateway 1" then sends

the same Emergency Command to each Gateway IP

address listed in its static IP address "table" via the Router.

With each Gateway receiving the Emergency Command

from "Gateway 1", each of these Gateways can then send

the Emergency Command to each of its assigned locks.

Notice that DL-Windows is not needed to disseminate

Emergency Commands and therefore not shown in this

diagram.

GATEWAY

1

GATEWAY

2

GATEWAY

4

)

)

)

)

)

)

)

)

)

)

)

)

)

)

)

)

)

)

)

)

) ) ) )

)

)

) )

)

)

)

)

)

)

)

)

)

) )

)

)

)

)

) ) )

)

) ) ) )

)

)

)

Router

GATEWAY

3

)

)

)

)

)

)

)

)

)

)

communication between Gateways, each Gateway must

possess the static IP address of every other Gateway in

the Account. The static IP address "table" is distributed to

each Gateway in the Account upon:

● The addition of a new Gateway to the Account

● The removal of a Gateway from the Account

● A manual Emergency Group change

44 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Emergency Commands > Set Emergency Groups (cont'd)

Setting Emergency Groups

Emergency Group association of any Gateway may be

intentionally changed from "GROUP A" to another Group

(GPB, GPC or GPD). Note: A single Gateway can only be

assigned to one Emergency Group at a time. To change a

Gateway assignment to another Group, click to highlight

the desired Gateway, then click the desired Emergency

Group checkbox.

Note: Every Gateway MUST have an association to an

Emergency Group.

After making selections, click the Send button, and the new

Group associations will be distributed to the Gateways.

Setting Emergency Group Descriptions

The default Emergency Group names ("GROUP A",

"GROUP B", etc.) may be changed as desired. The new

Emergency Group name will then be reflected in the

Emergency Command screen. To modify the name, in

the Set Emergency Groups screen, double-click in the

Description field of the desired Group, and type the new

Emergency Group description name (maximum 16

characters).

When finished making changes to the Emergency Group

descriptions, click Close to save and exit the screen

(description changes do not require the use of the Send

button).

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 45

Networx Lock Right-Click Profile Menu

For wireless locks, additional options are available for Networx Lock Profiles. In the Account List area, click the Account,

then click the small "+" sign next to the "blue file cabinet" icon, and all Lock Profiles in the Account appear. Click the de-

sired Lock Profile (denoted by the "padlock" icon) then right-click to display the right-click menu shown below.

Note: The first three items listed (plus "Rename") in this right-click menu (shown below) are items that also exist for non-

wireless locks. For information regarding these menu items, see OI382.

● New Lock(s) Profile (see OI382)

● Clone Lock Profile (see OI382)

● Delete Lock Profile (see OI382)

● View Status of Lock (page 46)

● Link / Unlink Lock Profile (page 47)

● Locate Lock (page 48)

● Update Date / Time in Lock (page 48)

● Take Lock Out of Passage (page 48)

● Put Lock Into Passage (page 49)

● Update Lock Firmware (page 49)

● Rename (see OI382)

46 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

In the Account List area, click to highlight a Lock Profile, then right-click and select View Status of Lock from the menu

that appears. Upon selection, the Lock Status is updated and retrieved, and displays various attributes of the selected

lock. Note: Lock must be Linked to a Lock Profile in order to view the Lock Status screen.

Lock Description

Displays the name of the selected Lock Profile.

Lock Type

Specifies the model of the Trilogy Networx™ series locking

device, such as "PDL6100", "DL6100" or "PL6100".

Serial Number

Displays the lock's unique serial number assigned and pro-

grammed into the lock firmware at the factory. Each Networx

lock is identified in the system by this unique serial number.

Gateway

Displays the name of the Gateway to which the selected

physical lock is assigned.

IP Address

Displays the IP address of the Gateway to which the physi-

cal lock is assigned.

GTW Rx

Indicates the radio transmission strength, as measured be-

tween the Gateway to the physical lock. A higher number

indicates stronger signal.

LCK Rx

Indicates the radio transmission strength, as measured be-

tween the physical lock to the Gateway. A higher number

indicates stronger signal.

Firmware Version

Indicates firmware source code edition of the selected

physical lock.

Battery

Displays the status of the battery powering the physical

lock. If battery status cannot be retrieved, "Unknown" will

be displayed.

Lock Status

Indicates the latest condition of the physical lock (i.e.

"Locked", "Passage", etc.). If status is unknown or unable

to be retrieved, "Communication Error" will be displayed.

Communication Status

Indicates the integrity of the communication link between

the physical lock and the Gateway. If status is unknown or

unable to be retrieved, "Communication Error" will be dis-

played.

Last Updated

Displays the date and time of the latest lock status update.

Update (button)

Click to request an updated lock status from the physical

lock. All fields will be refreshed upon lock status retrieval.

Right-Click Menu > View Status of Lock

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 47

In the Account List area, click to highlight a Lock Profile, then right-click and select Link / Unlink Lock Profile from the menu

that appears. Upon selection, a condensed version of the Link / Unlink Lock Profile screen appears. For detailed information

about Linking physical locks to Lock Profiles, see "LINKING PROCEDURE" on the bottom of page 14.

Lock Description

Displays the name of the selected Lock Profile.

Currently Linked To

Displays the physical lock's serial number, the Gateway De-

scription, and the Gateway's IP address to which the physical

lock is currently Linked. Note: The information in this field is

only displayed when the physical lock is Linked to a Lock Pro-

file.

Available Serial Numbers

This pull-down list displays the lock serial numbers of all

physical locks of the same lock model (Lock Type) discov-

ered by all Gateways in the current Account. Each lock

serial number is unique and assigned to the physical lock at

the factory.

Link (button)

Click this button to "Link" the selected Lock Profile (Lock

Description field) with the selected physical lock serial

number (from the Available Serial Numbers pull-down

list).

Unlink (button)

Click this button to remove the Link between the physical

lock and the Lock Profile. Note that after the Link is re-

moved, the physical lock serial number previously dis-

played in the Currently Linked to field is then displayed in

the Available Serial Numbers pull-down list ready for Link-

ing.

Right-Click Menu > Link / Unlink Lock Profile

48 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Right-Click Menu > Locate Lock

In the Account List area, click to highlight a Lock Profile, then right-click and select Locate Lock from the menu that appears.

Upon selection, the Locate Time screen appears where you can set the duration of time (in seconds) for the selected lock to

beep and flash its red LEDs. This option is typically used when you wish to find the physical lock or to confirm the wireless

connection is operational. Note: The physical lock may be located even if it is not Linked to a Lock Profile.

Locate time in seconds

Click the pull-down menu to set the duration of time (in

seconds) for the selected lock to beep and flash its red

LEDs. Up to 255 seconds (4 minutes 15 seconds) can be

selected; default duration is 30 seconds.

OK (button)

Click OK and the physical lock will beep and flash its red

LEDs for the selected duration.

Cancel

Click to exit without requesting the locate Action.

Note: All locks on a Gateway may be sent the locate

command (Gateway Configuration > Actions > Locate All

Locks on Gateway). For more information, see page 27.

IMPORTANT: If the selected physical lock is in an Emer-

gency state (Emergency Passage or Emergency Lock

Down ), this Take Lock Out of Passage menu item will be

ignored if selected. Lock must be taken out of its Emer-

gency state (Emergency Return to Normal) before it will

accept this menu command.

For more information about Emergency Commands, see

page 37 and page 38.

Right-Click Menu > Take Lock Out of Passage

In the Account List area, click to highlight a Lock Profile, then right-click and select Take Lock Out of Passage from the menu

that appears. Upon selection, a command is sent to the physical lock to change its state to "locked" ("secured"). The Lock

Status screen will automatically appear, displaying the updated Lock Status ("Locked").

TIP: For more information about Passage Mode and "Passage", see OI382.

Right-Click Menu > Update Date / Time in Lock

In the Account List area, click to highlight a Lock Profile, then right-click and select Update Date / Time in Lock from the

menu that appears. Upon selection, a command is sent to the physical lock to update the date and time based upon the

current time and date settings of the PC running DL-Windows.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 49

IMPORTANT: If the selected physical lock is in an Emer-

gency state (Emergency Passage or Emergency Lock

Down ), this Put Lock Into Passage menu item will be

ignored if selected. Lock must be taken out of its Emer-

gency state (Emergency Return to Normal) before it will

accept this menu command.

For more information about Emergency Commands, see

page 37 and page 38.

Right-Click Menu > Put Lock Into Passage

In the Account List area, click to highlight a Lock Profile, then right-click and select Put Lock Into Passage from the menu that

appears. Upon selection, a command is sent to the physical lock to change its state to "unlocked" ("unsecured"). The Lock

Status screen will automatically appear, displaying the updated Lock Status ("In Passage").

TIP: For more information about Passage Mode and "Passage", see OI382.

Right-Click Menu > Update Lock Firmware

In the Account List area, click to highlight a Lock Profile, then right-click and select Update Lock Firmware from the menu

that appears. Upon selection, the standard Windows Open dialog box appears (shown below), allowing you to browse for

the binary ".bin" file containing the lock firmware update.

Select the lock firmware file based on correct Lock Type (model), then click Open to initiate the update process.

The system will check the integrity of the firmware, burn it into the physical lock memory, and reboot the lock. Upon com-

pletion, the Lock Status screen will automatically open. In the Firmware Version field (shown below), verify the updated

firmware version of the physical lock. Note: Though not always necessary, it is recommended to send a full download to

the lock ("Send Profile").

50 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

LOCK ASSIGNMENT FAILURE

I discovered the lock successfully but after making the

selection and selecting "Assign Lock", the following

message appeared:

This message appears after several configuration at-

tempts by the Gateway. This indicates the physical

lock did not successfully receive the configuration data

(internal lock designation, a specific radio channel and

security data), and therefore is unable to be assigned

to the Gateway.

When this message appears, perform of the following:

1. Click Yes to first view the locks that were not con-

figured / assigned (by viewing the Gateway Lock

Table).

2. In the Gateway Configuration screen, click Tools

> Send Lock Config Table to the Gateway. This

will attempt to re-configure the lock(s) that failed

the initial assignment attempts. See page 22 for

more information regarding the use of this feature.

LOCK DISCOVERY FAILURE

I am trying to discover my lock, but DL-Windows can't

find it.

If no locks are found after a discovery attempt:

1. Verify that the lock is reset ("defaulted"). See the

programming instructions that came with your lock

for reset procedure.

2. Verify the lock is installed within an acceptable ra-

dio range of the Gateway. Refer to WI2085 for

information about installation and range.

● Test range with the Networx Signal Meter tool (part

AL-NSM).

3. Verify the Gateway has been mounted and physi-

cally installed as described in the instructions in-

cluded with the unit.

4. In the Gateway Configuration screen, try increas-

ing the Number of Locks to Discover (from the

pull-down).

EXISTING LOCK COMMUNICATION

FAILURE

I am no longer able to communicate with an existing

Networx lock. It was working just fine, now it does not

work!

Before attempting to re-establish communication, con-

sider the following:

1. Has something changed to affect the communica-

tion?

● Is something blocking the radio signal from the

Gateway to the lock?

● Check the radio signal from the Gateway using

the Networx Signal Meter tool (part AL-NSM).

Is the signal strength very weak?

2. Is the lock still functioning? Find the physical lock

and attempt to unlock by entering a working User

Code. Are the key-presses even causing beeping

sounds?

After verifying above, if the signal strength to that lock

has always been strong and suddenly it is non-existent,

the lock may have an internal failure. To reestablish a

connection with the lock, perform the following steps:

1. Reset ("Default") the lock (see the programming

instructions that came with the lock for the reset

procedure).

2. Re-discover the lock. Upon assignment, the fol-

lowing message will display:

This message appears because the lock was never

removed from the Gateway table, therefore the

lock is simply re-configured (received configuration

data, including its internal lock designation, a spe-

cific radio channel and security data).

Note: Re-Linking the lock is not required.

3. Download the Lock Profile to resume normal lock

operation.

TROUBLESHOOTING

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 51

WIRELESS LOCK MEMORY FAILURE

My Schedules no longer function and/or my User

Codes no longer unlock the door.

It is difficult to lose the lock programming. For exam-

ple, when replacing batteries, to erase the entire pro-

gram, you actually need to disconnect the batteries

and press and hold a keypad button for several sec-

onds.

However, upon disconnecting the batteries, if a key is

accidentally pressed, the lock may lose its time / date

information. In this case, simply turn to page 48 and

follow the procedure for the "Right-Click Menu > Up-

date Date / Time in Lock".

If upon disconnecting the batteries, you accidentally

hold down a key for several seconds and indeed lose

the lock programming, the solution is to re-discover

the lock and re-download the program. See section

"Discovering / Assigning Wireless Locks" on page

13. Note: Keep in mind that although this physical

lock has lost its programming, both DL-Windows and

the Gateway still consider the state of the physical

lock as unchanged (still powered up, assigned and in

operation). The following popup will appear upon

attempted re-assignment of the lock.

Note: Re-Linking the lock is not required.

GATEWAY HIGHLIGHTED RED

(UNREACHABLE)

How do I re-establish communication with a Gateway

that is highlighted in red (unreachable)?

A working Gateway (discovered on the network,

added to an Account and operational) is highlighted

blue in the Gateway Configuration screen. When a

working Gateway has subsequently lost communica-

tion with the network, the Gateway is highlighted red

in the Gateway Configuration screen.

To re-establish a connection to the Gateway, click to

select the red highlighted Gateway in the list, then

click Actions > Relocate Gateways (Displayed in

red). See page 28 for detailed information about re-

establishing a connection.

COMPUTER CRASH!

My computer running DL-Windows just crashed! I

had a working system, complete with wireless locks,

Gateways and a computer running DL-Windows--but

that computer no longer works! What do I do?

The Gateways and wireless locks are still up and run-

ning, and therefore they still hold the configuration

data (its internal lock designation, a specific radio

channel and security data) necessary to get your sys-

tem working. The data may be retrieved from the

Gateways using a new copy of DL-Windows on a new

PC (assuming you are in possession of the Security

Password). Refer to page 23, Gateway Configura-

tion > Tools > Import Gateway and Assigned

Locks to rebuild your database.

TROUBLESHOOTING (cont'd)

52 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

ACCESS = Entry into a restricted area.

ASSIGN = Add to hardware or specify a relationship.

Can be used with User Codes and locks ("to assign

User Codes to specific locks"), or with hardware

identification ("the factory assigns each lock a unique

serial number"), or a fixed wireless communication

channel between locks and a Gateway ("locks

assigned to a Gateway").

AUDIT TRAIL = A date/time stamped log of previous

lock events.

CLOCK

• REAL TIME CLOCK = An accurate built-in clock

that allows date/time stamping of events. The

clock can be slowed or speeded up to fine tune

long term accuracy to within three minutes per

year.

CODE = Numeric sequence of numbers (such as: 1234)

entered at the keypad. If Star-Enter-Key is required,

must be followed by a [:] key.

COM PORT = A computer serial communications port

used to communicate with the Lock and/or Data

Transfer Module.

COMMUNICATE = To send or receive a transmission.

To avoid the directionally confusing terms of

"download" and "upload", the word "communicate" is

used in this guide.

CONFIGURE = To "assign" (add) discovered physical

locks to a Gateway (by sending the "Lock Config

Table" to the selected Gateway). Configuring ensures

a fixed wireless communication channel exists

between selected physical locks and a selected

Gateway.

The Gateway Configuration screen allows you to

select a Gateway and allow that Gateway to discover

physical locks; these physical locks can then be

assigned to that selected Gateway. When the Use

Selected Locks button is clicked (in the

"DISCOVERED LOCKS" POPUP), the Gateway

sends "configuration data" to the selected locks. This

"configuration data" contains items (such as an

internal lock designation, a specific radio channel and

security data) that are all embedded in what is called

a "Lock Config Table". This "configuration data"

instructs the physical lock(s) to communicate ONLY

with that Gateway and prevents other Gateways from

communicating with the physical lock(s).

In short, the Gateway tries to "configure" the selected

physical locks by assigning the selected physical

locks to the Gateway.

CREDENTIAL = A generic word used to indicate a PIN

number pressed into a lock keypad, or a proximity

card or proximity keyfob.

DATA TRANSFER MODULE = A device that permits

transfer of program / data between a computer and

the lock.

DATE = Month, Day and Year entered as MMDDYY.

DAY OF WEEK = Sunday through Saturday.

DEFAULT = "Default" settings are the original settings

that were set at the factory; in other words, it is the

lock's original factory condition when the lock was first

taken out of its box. The default settings are

permanently encoded within the lock's fixed memory,

and when the lock is first started, or when power is

removed and re-applied, the original factory default

settings are re-loaded and take effect.

DELETE = Used interchangeably with "Remove". User

Codes (PINs) and proximity credentials can exist

(occupy a User Number) within the lock programming,

but are removed when "deleted" (thus the entry of a

non-existent PIN does not allow access). Similarly,

when used with DL-Windows Operators and

Administrators, "delete" describes an Operator or

Administrator who's Name, Full Name, Type and

Password was removed from DL-Windows.

DHCP (Dynamic Host Configuration Protocol) =

Automatic assignment of IP addresses to devices that

are connected to a network. It eliminates having to

manually assign fixed IP addresses.

DISABLE = User Codes (PINs) and proximity credentials

can exist (occupy a User Number) within the lock

programming, but can be rendered inoperative via

Schedule, download or keypad programming (PIN

entry does not allow access). Similarly, when used

with DL-Windows Operators and Administrators,

"disable" describes an Operator or Administrator

who's Name, Full Name, Type and Password exist

within DL-Windows but is rendered inoperative.

Contrast with "enable," which means active and

operational.

DISCOVER = To "discover" Gateways, the system

searches for Gateways not yet added to an Account;

to "discover" locks, the selected Gateway searches for

locks not yet assigned to Gateways.

DOWNLOAD = See COMMUNICATE.

Glossary

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 53

Glossary (cont'd)

EMERGENCY COMMANDS = For use only with the

Trilogy Networx wireless network, wireless commands

can be sent to all wireless locking devices in an

Account during a crisis or other urgent situation:

"Emergency Lock Down", to lock all doors in the

Account; "Emergency Passage", to unlock all doors

in the Account; and Emergency Return to Normal",

to revert all assigned locks to the state they were in prior

to the initiation of the Emergency command.

EMERGENCY GROUP = Upon the addition of each

Gateway into an Account, the Gateway is

automatically placed into an Emergency Group

("GROUP A" by default). This is done so that upon

the initiation of an Emergency Command, ALL

Gateways in the Emergency Group (and their

assigned locks) will respond to Emergency

Commands issued from DL-Windows. In addition, the

automatic placement of a new Gateway into an

Emergency Group allows for keypad-initiated

Emergency Commands to lock down an entire system

from a single wireless lock.

ENABLE = See DISABLE

ERASE = See DELETE

EVENTS = Recorded lock activity.

FIRMWARE = The software programming that runs

internally within the physical lock and Gateway

circuitry, containing the instructions that these devices

use to perform their various functions. Firmware can

be updated, if necessary.

FUNCTION (also called Programming Functions) =

The numbers used to program lock features

(enabling/disabling Users, User Groups, Passage

Mode, Schedules, etc.).

GROUP = See EMERGENCY GROUP

GTW Rx = Indicates the radio transmission strength, as

measured between the Gateway to the physical lock.

A higher number indicates stronger signal.

GUARD TOUR = A Guard Tour Code is used to log the

movement of a security guard as he or she makes

rounds from one assigned guard tour station to the

next. A Guard Tour Code is used to log the

movement of a security guard as he or she makes

rounds from one assigned guard tour station to the

next. Entering the User 299 code provides precise

verification and accountability of a guard's movements

by logging the location with a time/date stamp in the

Event Log (Audit Trail).

IMPORT = When the Account information stored in DL-

Windows is lost (such as with a stolen laptop)--AND--

the DL-Windows backup files are either non-existent,

inadequate or lost, the "Import" options can be used

to rebuild an existing wireless system using the data

stored inside the onboard memory of the installed

Gateway device(s).

IP ADDRESS = The IP (Internet Protocol) address is a

unique address of a device (such as a computer or a

Gateway) connected to a TCP/IP corporate Intranet.

IP addresses are written as four groups of numbers

separated by periods; these groups are called

"octets". IP addresses can be permanent ("static") or

dynamically assigned (by DHCP) when a device, such

as a Gateway, is powered.

KEYPAD = 10-numeric keys, : and special ;

key.

KEYPAD PROGRAMMING = Ability to program the lock

through the keypad.

KEYPRESS = Pressing a button on the lock’s keypad.

LCK Rx = Indicates the radio transmission strength, as

measured between the physical lock to the Gateway.

A higher number indicates stronger signal.

LINK = In DL-Windows, the word "Link" is used to

describe the specific action of associating a Lock

Profile to the serial number of the physical lock

installed on the door.

LOCATE =

● With physical lock(s), the Locate command

causes the physical lock to "beep" and flash its

LED (helpful when you wish to find the physical

lock or confirm the lock's wireless connection is

operational).

● When used with a Gateway, refers to re-

discovering a "lost" Gateway device on the

network. Used when an operational Gateway has

lost its network connection, and appears

highlighted red in the Gateway Configuration

screen.

LOCK = A generic word used to indicate one of the

many Alarm Lock locking devices that can be

purchased, including devices such as the DK series

keypads that trigger other locking devices.

54 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

Glossary (cont'd)

LOCK CONFIG TABLE = When a Gateway is

"discovered" and added to an Account, DL-Windows

sends a Lock Config Table which contains the

assigned (or unassigned) lock data stored in the

Gateway memory. The table is a database structure

that is designed to hold all physical lock data (serial

numbers, etc.).

LOCK PROFILE = See PROFILE

LOCK ID = Identification of each door with a specific

number--or in other words, a number representing an

individual lock within an Account.

LOCK TYPE = Specifies the model of the Alarm Lock

locking device, such as "PDL6100", "DL6100" or

"PL6100".

LOG = See... AUDIT TRAIL.

PASSAGE = Allow anyone to pass through the door

without a User Code or proximity credential (door is

unlocked).

PHYSICAL = Same as "Real". Tangible, not virtual.

See VIRTUAL.

PROFILE = "Lock Profiles" may also be called "Lock

Programs" or "Virtual Locks". A lock "Profile" can be

thought of as a "virtual" lock, created within DL-

Windows, that contains all of the instructions that a

"real" ("physical") lock uses to perform its various

functions. Use DL-Windows to create a lock "Profile"

on your computer, then transfer and store the "Profile"

in the memory of the "real" lock. The lock "Profile" is

essentially a computer database file that maintains

User Codes, Features, Time Zones and Schedules.

When creating these virtual lock Profiles, you are also

designing the entire virtual system--conceptualizing

which doors will have which locks, adding User

names and allowing or restricting access to the virtual

locks by the various Users in the Account.

PROXIMITY CREDENTIAL = See CREDENTIAL

PROGRAM MODE = A mode allowing program/data to

be entered through the keypad. Only specific Users

can program a lock manually, by entering their USER

CODE, followed by the ; key. To exit program

mode, hold any key until repeated beeps are heard.

PROXIMITY CARDS = See CREDENTIAL.

REAL = Same as "Physical". Tangible, not virtual. See

VIRTUAL.

SCHEDULE = A programmed operation (enable /

disable, lock / unlock, etc.) on a specific day (Sunday

through Saturday) and time.

SUBNET (SUBNETwork) = To improve security and

processing performance, network administrators often

divide their corporate Intranets into interconnected but

separate segments called "subnets". Subnets also

allow multiple users to access the Intranet with the

same subnet address. A router is typically used to

allow network traffic to pass between subnets.

SUBNET MASK = The IP protocol makes use of a

Subnet Mask to more efficiently route packets to their

correct network destinations. When a Gateway

receives a data packet, the Subnet Mask indicates

how many bits of the packet's destination address are

to be used for routing and which bits are to be

"masked" (ignored). The Subnet Mask can be

thought of as a "filter" that allows the system to ignore

unnecessary information, thus increasing efficiency.

This information must be obtained from your network

administrator.

TIME = Hours and Minutes in the HHMM format.

TIME/DATE STAMP = A recorded date and time that an

event occurred.

TIMEOUT = Immediate operation for a specified number

of hours.

TYPE = See LOCK TYPE.

UPLOAD = See COMMUNICATE.

USER = A person that has their personal information

typed into the Global Users screen, and is assigned

a User Code (PIN) or proximity credential (where

applicable). This User is then added to (enabled

within) Lock Profiles, as necessary.

VIRTUAL = Simulated on a computer. DL-Windows

allows you to create a "Lock Profile" that can be

thought of as a "virtual" lock, created within DL-

Windows, that contains all of the data that a

"real" (physical) lock uses to perform its various

functions. When creating these "virtual" lock Profiles,

you are also designing the entire "virtual" system--

conceptualizing which doors will have which locks,

adding User Names and allowing or restricting access

to the virtual locks by the various Users in the

Account. Later, you will "Link" these lock Profiles with

the real locks installed on the doors.

DL-WINDOWS™ for Networx™ V5 USER'S GUIDE 55

NOTES

56 DL-WINDOWS™ for Networx™ V5 USER'S GUIDE

ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants

its products to be free from manufacturing defects in mate-

rials and workmanship for twenty four months following the

date of manufacture. ALARM LOCK will, within said pe-

riod, at its option, repair or replace any product failing to

operate correctly without charge to the original purchaser

or user.

This warranty shall not apply to any equipment, or any part

thereof, which has been repaired by others, improperly

installed, improperly used, abused, altered, damaged, sub-

jected to acts of God, or on which any serial numbers have

been altered, defaced or removed. Seller will not be re-

sponsible for any dismantling or reinstallation charges,

environmental wear and tear, normal maintenance ex-

penses, or shipping and freight expenses required to re-

turn products to ALARM LOCK. Additionally, this warranty

shall not cover scratches, abrasions or deterioration due to

the use of paints, solvents or other chemicals.

THERE ARE NO WARRANTIES, EXPRESS OR IM-

PLIED, WHICH EXTEND BEYOND THE DESCRIPTION

ON THE FACE HEREOF. THERE IS NO EXPRESS OR

IMPLIED WARRANTY OF MERCHANTABILITY OR A

WARRANTY OF FITNESS FOR A PARTICULAR PUR-

POSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU

OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE

PART OF ALARM LOCK.

Any action for breach of warranty, including but not limited

to any implied warranty of merchantability, must be

brought within the six months following the end of the war-

ranty period.

IN NO CASE SHALL ALARM LOCK BE LIABLE TO ANY-

ONE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES FOR BREACH OF THIS OR ANY OTHER

WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE

LOSS OR DAMAGE IS CAUSED BY THE SELLER'S

OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional who

installed and maintains your security system. In order to

exercise the warranty, the product must be returned by the

security professional, shipping costs prepaid and insured

to ALARM LOCK. After repair or replacement, ALARM

LOCK assumes the cost of returning products under war-

ranty. ALARM LOCK shall have no obligation under this

warranty, or otherwise, if the product has been repaired by

others, improperly installed, improperly used, abused, al-

tered, damaged, subjected to accident, nuisance, flood,

fire or acts of God, or on which any serial numbers have

been altered, defaced or removed. ALARM LOCK will not

be responsible for any dismantling, reassembly or reinstal-

lation charges, environmental wear and tear, normal main-

tenance expenses, or shipping and freight expenses re-

quired to return products to ALARM LOCK. Additionally,

this warranty shall not cover scratches, abrasions or dete-

rioration due to the use of paints, solvents or other chemi-

cals.

This warranty contains the entire warranty. It is the sole

warranty and any prior agreements or representations,

whether oral or written, are either merged herein or are

expressly cancelled. ALARM LOCK neither assumes, nor

authorizes any other person purporting to act on its behalf

to modify, to change, or to assume for it, any other war-

ranty or liability concerning its products.

In no event shall ALARM LOCK be liable for an amount in

excess of ALARM LOCK's original selling price of the

product, for any loss or damage, whether direct, indirect,

incidental, consequential, or otherwise arising out of any

failure of the product. Seller's warranty, as hereinabove set

forth, shall not be enlarged, diminished or affected by and

no obligation or liability shall arise or grow out of Seller's

rendering of technical advice or service in connection with

Buyer's order of the goods furnished hereunder.

ALARM LOCK RECOMMENDS THAT THE ENTIRE SYS-

TEM BE COMPLETELY TESTED WEEKLY.

Warning: Despite frequent testing, and due to, but not

limited to, any or all of the following; criminal tampering,

electrical or communications disruption, it is possible for

the system to fail to perform as expected. ALARM LOCK

does not represent that the product/system may not be

compromised or circumvented; or that the product or sys-

tem will prevent any personal injury or property loss by

burglary, robbery, fire or otherwise; nor that the product or

system will in all cases provide adequate warning or pro-

tection. A properly installed and maintained alarm may

only reduce risk of burglary, robbery, fire or otherwise but

it is not insurance or a guarantee that these events will not

occur. CONSEQUENTLY, SELLER SHALL HAVE NO LI-

ABILITY FOR ANY PERSONAL INJURY, PROPERTY

DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE

PRODUCT FAILED TO GIVE WARNING. Therefore, the

installer should in turn advise the consumer to take any

and all precautions for his or her safety including, but not

limited to, fleeing the premises and calling police or fire

department, in order to mitigate the possibilities of harm

and/or damage.

ALARM LOCK is not an insurer of either the property or

safety of the user's family or employees, and limits its li-

ability for any loss or damage including incidental or con-

sequential damages to ALARM LOCK's original selling

price of the product regardless of the cause of such loss or

damage.

Some states do not allow limitations on how long an im-

plied warranty lasts or do not allow the exclusion or limita-

tion of incidental or consequential damages, or differenti-

ate in their treatment of limitations of liability for ordinary or

gross negligence, so the above limitations or exclusions

may not apply to you. This Warranty gives you specific

legal rights and you may also have other rights which vary

from state to state.

ALARM LOCK LIMITED WARRANTY