Alarm Lock XNarrow_DL1200 DL1300 PDL1300_WI1458F.03_INST DL1200, DL1300, PDL1300 Narrow Stile Mounting Instructions X DL1200 WI1458F.03 INST

User Manual: Alarm Lock DL1200, DL1300, PDL1300 Narrow Stile Mounting Instructions Installation Manuals

Open the PDF directly: View PDF .
Page Count: 8

1

DL1200 - DL1300 - PDL1300

NARROW STILE ACCESS LOCKS

MOUNTING AND INSTALLATION

INSTRUCTIONS

GENERAL DESCRIPTION

The DL1200, DL1300 and PDL1300 are manually programma-

ble narrow stile entry trim for Adams Rite® 4710, 4730 and 4900

deadlatch locks, and 1850, 1950, 4070, MS1850S and

MS1950S series deadbolts for narrow stile aluminum doors*.

The DL1200, DL1300 and PDL1300 will retract the existing Ad-

ams Rite® latch when an access code is entered (or a credential

is presented) and the lever is pressed down (or the turnpiece

turned). The trim is designed to operate with any Adams Rite®

interior device such as a "pushpaddle" or lever. Because Ad-

ams Rite® trim exists on the inside, the "hold-back feature re-

mains operational for a continuous unlatched function (see Ad-

ams Rite® instructions). Entering a passage mode function

code activates latched passage mode (device is unlocked but

the lever or turnpiece is engaged continuously) until another

passage mode function code is entered, re-locking the trim. All

locks are equipped with a mechanical metal key override. See

OI310, OI311 or OI312 for programming information.

MECHANICAL FEATURES

The overall enclosure housing is 14 3/8" inches high, 1 5/8"

inches deep and 1¾" inches wide. The trim is through-bolted to

the stile of the door (using four #10 screws) and are secured on

the interior side of the door. Supported stile thickness is 1¾".

 DL1200 Series supports 100 users, fingertip/keypad pro-

grammable

 DL1300 Series supports 2000 users and includes 40,000

event audit trail and 500 event schedule. Keypad or PC

programmable

 PDL1300 Series supports 2000 PIN or Proximity users and

includes 40,000-event audit trail and 500 event schedule.

Keypad or PC programmable

 Aluminum door retrofit outside trim for Adams Rite® 1850,

1950, 4710, 4070, 4730, 4900, MS1850S and MS1950S

Series locks

 Familiar Trilogy® programming & electronics

 All-metal, vandal-resistant 12-button keypad supports 3-6

digit PIN codes (3-5 digits on the DL1200), and multilevel

user hierarchy (master, manager, supervisor and basic

users)

 Keypad or PC programmable (see model information).

Quickly and easily add or delete users and enter "passage

mode", service codes, group lock-out & group-enable

© ALARM LOCK 2015 WI1458F 05/15

*Adams Rite Manufacturing Co., Pomona, CA. www.adamsrite.com. All products, product names and services

described in this manual are for identification purposes only and may be trademarks of their respective companies.

 HID Proximity ID cards, keyfobs and proximity tags sup-

ported in PDL1300 series which features built-in Proximity

reader (High security applications can require use of both

PIN code plus Proximity ID card for access)

 Real time clock and PC programmable automatic lock/

unlock scheduling for 500 events (1300 Series models)

 Wide weatherproof operating range from -31 to 151ºF (-35

to 66C)

 Provides 100,000 operations using off-the-shelf long life

DL123A lithium batteries, and includes audible and visual

low battery alert

 Non-handed; fully field-reversible

 Mechanical key override; interchangeable cores supported

(Corbin/Russwin, Yale, Schlage, Medeco)

 Mortise Cylinder, 1¼" supplied (supports 1-1/8", 1¼", 1-

3/8" and 1½"

 Compact styling 14-3/8"H x 1-5/8"D x 1¾"W

 Backsets 31/32",1-1/8" and 1½"; stile thickness 1¾"

TABLE OF CONTENTS

GENERAL DESCRIPTION ..................................... 1

MECHANICAL FEATURES .................................... 1

MOUNTING AND INSTALLATION ........................ 2

INSTALL CYLINDER ......................................... 3

VERIFY HAND ................................................... 3

INSTALL LEVER ................................................ 4

INSERT INTERFACE CYLINDER ............... 4

INSTALL LOCK ............................................. 5

INSTALL BATTERIES ................................... 6

TEST OPERATION ................................................. 7

NAPCO LIMITED WARRANTY.............................. 8

345 Bayview Avenue

Amityville, New York 11701

For Sales and Repairs 1-800-ALA-LOCK

For Technical Service 1-800-645-9440

or visit us at http://tech.napcosecurity.com/

(Note: Technical Service is for security professionals only)

Publicly traded on NASDAQ Symbol: NSSC

2

MOUNTING AND INSTALLATION

For factory prepped doors, use dimensions shown. Di-

mensions are referenced from center of 1¼" cylinder hole.

The Adams Rite® lock determines the backset.

When mounting the new Adams Rite® locks:

 Do not install the outside cylinder -- this trim replaces it;

 Do not install the faceplate (access to the cylinder set

screw in the lock is required during mounting and instal-

lation).

Mechanical Override Cylinder Cams

The DL1200 and DL/PDL1300 trim requires the use of an

oval Alarm Lock cam (supplied with cylinder). For other

manufacturers, please see the charts below.

Cylinder Collars:

The DL1200 and DL/PDL1300 can use a 1-⅛" & 1¼" mor-

tise cylinder without the use of a collar (1¼" requires two

plastic spacers, supplied). For cylinders longer than 1¼" a

collar is required.

Order collars from an Alarm Lock distributor.

Template (use WI1459)

Corbin-Russwin HW1344

Marks HW1346

Arrow HW1348

Schlage HW1349

Cams for Standard Mortise Cylinders

Sargent HW1348

Cams for IC Mortise Cylinders

Best* HW1343

Corbin-Russwin HW1345

Medeco HW1347

Schlage HW1350

Yale HW1351

*Will be supplied together with Best IC Housing (HW1352)

Cylinder Length Collar P/N

1-⅜ HW1331

1-½ HW1342

Cam for Mechanical Override Cylinder

Backset is determined by

the Adams Rite lock

3

Install Cylinder

1. Install Cylinder if not already installed at the factory.

Screws A & B (see Fig. 1) are correctly set at factory. If

it is difficult to screw in the cylinder, loosen the two

screws near the actuator (A) one turn. If you find the

cylinder is still difficult to screw in, then loosen the other

screws (B) one turn. Do not loosen the screws all the

way or it may be difficult to replace them properly!

Note: The trim is manufactured to use a 1-1/8" or

1¼" Alarm Lock mortise cylinder with a HW-1302 cam.

If the cylinder that will be used is longer than 1¼", a col-

lar must be utilized. Please see the collar information on

the previous page.

1a. Insert key half-way into the cylinder, then screw it in.

See Fig. 1a. If cylinder will

not seat flush, the cylinder

back stop screw may re-

quire loosening. Cylinders

that are longer than 1¼"

will require a collar, which

will stick out from the sur-

face when correctly in-

stalled. Please see the

cylinder information on the

previous page.

1b. After the cylinder is screwed in all the way, center

the keyway toward

the bottom (see Fig.

1b). If an interchange-

able core cylinder is

utilized, then center the

interface toward the

bottom. Tighten the

screws that were loos-

ened in step 1.

1c. Remove the key. Use a 1/16" hex wrench to screw

the cylinder back

stop screw in fully.

(See Fig. 1c) The

key should now

only rotate counter-

clockwise.

NOTE: To remove

cylinder, reverse

steps 1a-1c.

Setting the Door "Hand"

2. With the key always on the outside, the door hand is

generally determined by the location of the hinges--

hinges are either inside or outside. See Fig. 2.

2a. Setting Hand of Interface Cylinder/Adapter

See Fig. 2a to determine if changing the retractor arm is

necessary; if so, continue with the steps below.

2b. Remove the retaining ring

with a small tool such as

screwdriver or small needle-

nose pliers (see Fig. 2b).

Pull out the pin and the spring.

2c. Flip over the retractor arm

as shown in Fig. 2c.

2d. There are two types of

springs; an RH spring in-

stalled at the factory, and an

LH spring (supplied). Select

the LH spring (see Fig. 2d).

Fig. 1a: Insert key 1/2 way

into cylinder and screw in

RIGHT HAND LEFT HAND

STANDARD RH LH

REVERSE RHR LHR

Fig. 2: Cross Section Top View -- Door Hand

(Hinges)

(Keys)

(Keys)

STANDARD

REVERSE

Fig. 2a: LH and RH orientation for Interface cylinder, retractor arm, spring

and door latch. The RH orientation is shipped from the factory.

LH RH (factory installed)

Fig. 2b: Remove retaining

ring.

Fig. 2c: The retractor arm

placed for LH operation.

Fig. 1b: Center keyway toward bottom

Fig. 1c: Use 1/16" hex wrench to screw in

the cylinder back stop screw

Fig. 1: Install Cylinder if not already installed at the factory

A

B

Cylinder back stop

screw

4

2e. Pre-load the spring by placing the "anchor" end

over the "arm". See Fig. 2e below.

2f. Insert the pin through

the top of the new LH

spring.

2g. Insert the pin/spring

through the retractor arm

hole while simultaneously

inserting the "anchor" end

of the spring into the

small hole in the cylinder/

adapter. See Fig. 2g.

Pull the arm and hook its end onto the retractor arm.

2h. Re-install the retaining ring

displayed in Fig. 2h.

Finished configuration

shown at left (Fig. 2i).

Install the Lever

3. Install the lever with

proper orientation for

the lock/door hand used.

Tighten the set screw us-

ing a 1/8" hex wrench

(see Fig. 3).

IMPORTANT! The top of

the set screw must be at

(or below) lever surface. If

not, check to ensure the

lever is fully pushed to-

ward the trim.

3a. Install the Adams Rite® product as indicated by the

Adams Rite® door prep guide-

lines and instructions.

 If a new installation, the

face place must NOT be

installed at this time.

 If a retrofit installation,

remove the face plate.

Prepare the Door For

"Through-Bolting"

4. Place template (WI1459) as

shown. Important: Place

the template on top of existing

cylinder hole and parallel to the

door edge.

4a. Drill completely through the door for through-bolting

the four mounting holes and battery cover access

bolt hole.

 IMPORTANT!--Drill the holes STRAIGHT

THROUGH the door, or the through-bolts will not

fit in the lock! THIS IS ESSENTIAL! Drill slowly

and STRAIGHT through the door.

 Reposition the template as often as needed until

it is placed correctly.

Insert the Interface Cylinder

5. Loosen the set screw, then remove the outside cylin-

der (if present--See Fig. 5).

Fig. 3: Tighten lever set screw

with 1/8" hex wrench

Fig. 4: Template (WI1459)

through-bolt holes (circled)

LH RH (factory installed)

Fig. 2d: The RH spring is installed at the factory; the LH spring is supplied.

"anchor"

"arm" "arm"

"anchor"

Fig. 2h: Re-install retaining ring.

Fig. 2i: Ready for LH operation.

Fig. 2f: Insert pin into top of

spring.

pin

Fig. 2g: Insert pin and spring; pull arm and clip on hook cam lever.

Insert "anchor" end

into this hole.

Fig. 2e: Pre-load the spring (LH shown) before installing.

"arm"

"anchor"

"anchor"

placed behind

"arm"

Old interface

cylinder

Set screw

Fig. 5: Loosen set screw before removing the

old interface cylinder (if present)

5

5a. Push in latch and hold latch in all the way.

5b. While holding in the latch, carefully insert the inter-

face cylinder assembly into the cylinder hole. The hook

must be in front of the latch retractor and pass through

the notch in the lock case (see Fig. 5b).

5c. The interface cylinder must be centered and posi-

tioned flush with (or slightly below) the surface of the door

(see Fig. 5c).

5d. With the interface cylinder HELD SECURELY in its

correct position, tighten the set screw, securing the

interface cylinder to the lock (see Fig. 5d).

Important! If the interface cylinder is not parallel to

the door after tightening the set screw, then you must

verify that the original Adams Rite® lock body was origi-

nally installed correctly (installed square to the door).

Failure to ensure the interface cylinder is installed cor-

rectly could cause lock binding or improper operation of

the lock mechanism.

5e. Install the latch face plate.

Install Lock

6. Install the DL lock onto the door by aligning the two

posts on the front of the interface cylinder with the two

corresponding holes in the back of the DL lock. Lift the

tailpiece slightly to ensure the tailpiece enters the slot of

the interface cylinder.

6a. Secure the DL lock to the door with four through-

door mounting screws and two door plates. Place a door

plate on top of a pair of mounting holes and loosely se-

cure lock from the inside of the door. Snug all four

Fig. 5c: Position the interface cylinder

Fig. 5d: Tighten the interface cylinder set screw

Fig. 5e: Install the latch face plate

Fig. 6: Install lock onto the door

Fig. 5a: Push latch in and hold

Push in

latch during

interface

cylinder

installation

Interface cylinder

Fig. 5b: While holding latch in, place hook in front of

the latch retractor and through the notch

Notch

Hook

6

mounting screws before final tightening. Do not over-

tighten.

6b. Cover door plates with decorative plate covers by

sliding them from top to bottom on door plates.

Connect Batteries

7. Loosen the #8-32 Phillips pan head screw located on

the rear side of the base plate at the bottom of the lock

(see Fig. 7). Turn counter-clockwise until the battery

cover slides off the housing. Do not remove the screw

completely.

7a. Plug in the battery connector and insert the battery

pack into the battery compartment. Neatly push all

wiring inside the compartment. Holding battery in

place, slide cover back on. Secure the battery cover by

tightening the #8-32 Phillips pan head screw located on

the rear side of the base plate (access this screw from

the 7/16" thru-hole drilled in the door). Do not over

tighten the screw.

8. FOR NEW INSTALLATIONS: Refer to programming

instructions (OI310, OI311 or OI312) for specific in-

structions for "First Time Startup" and "Change Facto-

ry Master Code" before connecting the battery.

The lock must be powered up correctly (and have its

factory Master Code changed) or erratic lock behavior

can result.

Test operation: See next page.

Fig. 6a: Secure lock to door -- loosely at first

Door

Thru-Holes Door Plate

Fig. 6b: Slide down to install decorative plate covers

Fig. 7: The Phillips screw on the rear side locks or unlocks

the battery cover. Do not remove screw.

Fig. 7a: Install the battery pack: Push all wires inside the battery

compartment and slide plate back on.

7

TEST LOCK OPERATION

Before testing, be sure the lock has been powered-up

using the specific instructions in the OI310, OI311 or

OI312 manuals.

1. With key removed, ensure that the lever can be pushed

down and up. In addition, verify these lever motions

DO NOT retract the latch.

2. Release lever. Insert key and turn key fully counter-

clockwise.

3. Push the lever down and the latch should retract.

4. Release lever. Turn key clockwise and remove key.

The lever must not retract the latch when pressed

down.

5. While pressing the default access code on the lock key-

pad (press "1 2 3 4 5" on the DL1200 and press

"1 2 3 4 5 6" on the DL/PDL1300), note the following:

 For each number key pressed, the red LED lights.

 When the "5" button is pressed (or the "6" button on

the DL/PDL1300):

1. The green LED flashes for approximately 5 sec-

onds.

2. The latch retracts when the lever is pushed down.

6. Test the exit device mounted inside (paddle / egress

bar, etc.) and confirm it is operating correctly.

SEE PROGRAMMING INSTRUCTIONS OI310, OI311

or OI312 FOR KEYPAD PROGRAMMING INFOR-

MATION.

Test Step 1

Test Step 2

Latch

retracted

Test Step 3

Test Step 5

Test Step 4

8

ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants

its products to be free from manufacturing defects in mate-

rials and workmanship for twenty four months following the

date of manufacture. ALARM LOCK will, within said peri-

od, at its option, repair or replace any product failing to

operate correctly without charge to the original purchaser

or user.

This warranty shall not apply to any equipment, or any part

thereof, which has been repaired by others, improperly

installed, improperly used, abused, altered, damaged, sub-

jected to acts of God, or on which any serial numbers have

been altered, defaced or removed. Seller will not be re-

sponsible for any dismantling or reinstallation charges,

environmental wear and tear, normal maintenance ex-

penses, or shipping and freight expenses required to re-

turn products to ALARM LOCK. Additionally, this warranty

shall not cover scratches, abrasions or deterioration due to

the use of paints, solvents or other chemicals.

THERE ARE NO WARRANTIES, EXPRESS OR IM-

PLIED, WHICH EXTEND BEYOND THE DESCRIPTION

ON THE FACE HEREOF. THERE IS NO EXPRESS OR

IMPLIED WARRANTY OF MERCHANTABILITY OR A

WARRANTY OF FITNESS FOR A PARTICULAR PUR-

POSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU

OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE

PART OF ALARM LOCK.

Any action for breach of warranty, including but not limited

to any implied warranty of merchantability, must be

brought within the six months following the end of the war-

ranty period.

IN NO CASE SHALL ALARM LOCK BE LIABLE TO ANY-

ONE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES FOR BREACH OF THIS OR ANY OTHER

WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE

LOSS OR DAMAGE IS CAUSED BY THE SELLER'S

OWN NEGLIGENCE OR FAULT.

In case of defect, contact the security professional who

installed and maintains your security system. In order to

exercise the warranty, the product must be returned by the

security professional, shipping costs prepaid and insured

to ALARM LOCK. After repair or replacement, ALARM

LOCK assumes the cost of returning products under war-

ranty. ALARM LOCK shall have no obligation under this

warranty, or otherwise, if the product has been repaired by

others, improperly installed, improperly used, abused, al-

tered, damaged, subjected to accident, nuisance, flood,

fire or acts of God, or on which any serial numbers have

been altered, defaced or removed. ALARM LOCK will not

be responsible for any dismantling, reassembly or reinstal-

lation charges, environmental wear and tear, normal

maintenance expenses, or shipping and freight expenses

required to return products to ALARM LOCK. Additionally,

this warranty shall not cover scratches, abrasions or dete-

rioration due to the use of paints, solvents or other chemi-

cals.

This warranty contains the entire warranty. It is the sole

warranty and any prior agreements or representations,

whether oral or written, are either merged herein or are

expressly cancelled. ALARM LOCK neither assumes, nor

authorizes any other person purporting to act on its behalf

to modify, to change, or to assume for it, any other warran-

ty or liability concerning its products.

In no event shall ALARM LOCK be liable for an amount in

excess of ALARM LOCK's original selling price of the

product, for any loss or damage, whether direct, indirect,

incidental, consequential, or otherwise arising out of any

failure of the product. Seller's warranty, as hereinabove set

forth, shall not be enlarged, diminished or affected by and

no obligation or liability shall arise or grow out of Seller's

rendering of technical advice or service in connection with

Buyer's order of the goods furnished hereunder.

ALARM LOCK RECOMMENDS THAT THE ENTIRE SYS-

TEM BE COMPLETELY TESTED WEEKLY.

Warning: Despite frequent testing, and due to, but not

limited to, any or all of the following; criminal tampering,

electrical or communications disruption, it is possible for

the system to fail to perform as expected. ALARM LOCK

does not represent that the product/system may not be

compromised or circumvented; or that the product or sys-

tem will prevent any personal injury or property loss by

burglary, robbery, fire or otherwise; nor that the product or

system will in all cases provide adequate warning or pro-

tection. A properly installed and maintained alarm may

only reduce risk of burglary, robbery, fire or otherwise but

it is not insurance or a guarantee that these events will not

occur. CONSEQUENTLY, SELLER SHALL HAVE NO LIA-

BILITY FOR ANY PERSONAL INJURY, PROPERTY

DAMAGE, OR OTHER LOSS BASED ON A CLAIM THE

PRODUCT FAILED TO GIVE WARNING. Therefore, the

installer should in turn advise the consumer to take any

and all precautions for his or her safety including, but not

limited to, fleeing the premises and calling police or fire

department, in order to mitigate the possibilities of harm

and/or damage.

ALARM LOCK is not an insurer of either the property or

safety of the user's family or employees, and limits its lia-

bility for any loss or damage including incidental or conse-

quential damages to ALARM LOCK's original selling price

of the product regardless of the cause of such loss or

damage.

Some states do not allow limitations on how long an im-

plied warranty lasts or do not allow the exclusion or limita-

tion of incidental or consequential damages, or differenti-

ate in their treatment of limitations of liability for ordinary or

gross negligence, so the above limitations or exclusions

may not apply to you. This Warranty gives you specific

legal rights and you may also have other rights which vary

from state to state.

ALARM LOCK LIMITED WARRANTY