AlarmForce KP7315 REMOTE KEYPAD User Manual

AlarmForce Industries Inc. REMOTE KEYPAD Users Manual

Users Manual

KP-7 AlarmForce 2007.3.23 1RREEMMOOTTEE KKEEYYPPAADD ((KKPP--77)) zz Identifying the parts: 1. Tx LED 2. ACTIVE LED 3. 10 Numeric keys 4. “ + ” button – to send Emergency code 5. “○S” button – to send Status code 6. “ ” button – press after PIN Code to Part Arm the system 7. “ ” button –press after PIN Code to Arm the system 8. “ ” button – press after PIN to Disarm the system 9. “♪” button – to send Chime code 10. Tamper Switch zz LLEEDD IInnddiiccaattoorr:: zz AACCTTIIVVEE LLEEDD ((GGrreeeenn)):: zz When idle, both LED’s are off. After any key press, the Green LED goes on for 5 seconds indicating that KP-7 is active. zz However if the Green LED flashes during operation instead of being on steadily, this is an indication of a low battery. zz The LED turns off after successful completion of a valid keystroke sequence, or when the pause in between key stokes is longer than 5 seconds. <<NNOOTTEE>> "" When the Green LED turns off before a valid keystroke sequence is completed, the previous entered keys are ignored. zz TTxx LLEEDD ((RReedd)):: zz On for 2 seconds when transmitting. zz In tampered condition, the Red LED will flash whenever KP-7 is used. zz PPoowweerr:: zz KP-7 uses 3 “AAA” alkaline batteries as its power source. Its typical battery life is 5 years in a normal domestic environment. zz When KP-7 enters low battery status, a low battery signal will be sent out by KP-7 only after 20 regular signal transmissions have been consecutively sent in low battery mode. zz SSuuppeerrvviissiioonn:: zz Upon inserting the batteries for the 1st time, the KP-7 will promptly send out a supervisory signal. zz Thereafter, it continues to transmit supervisory signal periodically at intervals of 30 to 50 minutes. zz Use of the keypad will re-start the time count 30 to 50 minutes for next supervisory signal. zz PPoowweerr SSaavviinngg FFeeaattuurree:: zz When idle, KP-7 is in “standby” mode and uses no power. It will activate and “wake-up” for 5 seconds where any key is pressed.
KP-7 AlarmForce 2007.3.23 2zz After 5 seconds of key inactivity, the power goes off and it returns to Stand-by mode. zz Upon completion of a command input, the power goes off and KP-7 returns to Stand-by mode. zz TTaammppeerr PPrrootteeccttiioonn:: zz KP-7 is protected against any attempt to open the lid or to detach KP-7 from its mounting surface. zz In tampered condition, KP-7 will emit a beep every 30 seconds as warning to the user . zz In tampered condition, the Red LED will flash whenever KP-7 is used. zz MMoouunnttiinngg KKPP--77:: zz Break through the two or four knockouts where the plastic is thinner zz Using the holes of the base as a template, drill holes in the surface zz Insert the wall plugs if fixing into plaster or brick zz Screw the base to the wall zz Ensure that the tamper switch spring protruding through the back is fully depressed by the mounting surface. zz Fix the lid with the screw and clips to the base zz PPrrooggrraammmmiinngg KKPP--77:: 1. Remove the cover by loosening the fixing screw 2. Insert three “AAA” batteries 3. The Red LED indicator will flash briefly while components initialize and supervision code will be sent out. zz FFuunnccttiioonnss OOvveerrvviieeww:: This device complies with Part 15 of the FCC Rules and RSS-210 of Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution : To assure continued compliance, any changes or modifications not expressly approved by the party responsible for Dual Key Alarm Features:  Arm ¾ PIN code + “ARM”  Panic Alarm ¾ “1” + “3” simultaneously  Part Arm ¾ PIN code + “HOME”  Fire Alarm ¾ “4” + “6” simultaneously  Disarm ¾ PIN code + “OFF”  Emergency Alarm ¾ “7” + “9” simultaneously  Chime ¾ “♪”  Emergency ¾ “+”  Status ¾ “○S”
KP-7 AlarmForce 2007.3.23 3compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

Navigation menu