Alcatel Lucent France MO-V2-250MW-DB 9364 Metro Cell Outdoor V2.0 1900/850MHz 250Mw User Manual USERS MANUAL 1

Title page

Alcatel-Lucent 9364

Metro Cell - Outdoor V2 2100MHz and 1900/850MHz

Installation and commissioning

401-387-095

Issue 3

September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Legal notice

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective

owners.

The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.

Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside

Alcatel-Lucent without its written authorization.

Not to be used or disclosed except in accordance with applicable agreements.

Use pursuant to applicable agreements

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Contents

About this document

Purpose ............................................................................................................................................................................................ viivii

Reason for revision ..................................................................................................................................................................... viivii

New in this release ...................................................................................................................................................................... viivii

Intended audience ....................................................................................................................................................................... viivii

Supported systems ..................................................................................................................................................................... viiiviii

How to use this document ....................................................................................................................................................... viiiviii

Safety information ..................................................................................................................................................................... viiiviii

Prerequisites ................................................................................................................................................................................. viiiviii

Conventions used ....................................................................................................................................................................... viiiviii

Related information ................................................................................................................................................................... viiiviii

Document support ........................................................................................................................................................................ ixix

Technical support .......................................................................................................................................................................... ixix

How to order ................................................................................................................................................................................... ixix

How to comment ........................................................................................................................................................................... ixix

1Safety statements

Overview ...................................................................................................................................................................................... 1-11-1

Structure of safety statements ............................................................................................................................................... 1-21-2

Safety ........................................................................................................................................................................................... 1-41-4

Safety - specific hazards ......................................................................................................................................................... 1-51-5

Product safety ............................................................................................................................................................................. 1-81-8

2Product overview

Overview ...................................................................................................................................................................................... 2-12-1

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements iii

Functional description ............................................................................................................................................................. 2-22-2

Physical description ................................................................................................................................................................. 2-52-5

3Metro Cell installation and commissioning

Overview ...................................................................................................................................................................................... 3-13-1

Pre-installation information .................................................................................................................................................. 3-23-2

To mount the hardware to a wall ......................................................................................................................................... 3-43-4

To mount the hardware to a pole ......................................................................................................................................... 3-83-8

Metro Cell - Outdoor cabling ............................................................................................................................................. 3-113-11

Metro Cell - Outdoor commissioning process ............................................................................................................. 3-163-16

Post installation activities and checks ............................................................................................................................. 3-173-17

4Product specifications

Overview ...................................................................................................................................................................................... 4-14-1

Environmental and regulatory specifications ................................................................................................................. 4-24-2

AOvercasing installation

Overview ..................................................................................................................................................................................... A-1A-1

Overcasing installation instructions .................................................................................................................................. A-2A-2

BMetro Cell wall mount spacer

Overview ..................................................................................................................................................................................... B-1B-1

Wall mount spacer ................................................................................................................................................................... B-2B-2

CProduct conformance statements

Overview ..................................................................................................................................................................................... C-1C-1

European Union ........................................................................................................................................................................ C-2C-2

Glossary

Index

Contents

....................................................................................................................................................................................................................................

iv Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

List of figures

2-1 Alcatel-Lucent 9364 Metro Cell - Outdoor (with pole mounting bracket attached) ......................... 2-22-2

2-2 Alcatel-Lucent 9364 Metro Cell - Outdoor (2100 MHz variant) ............................................................. 2-52-5

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements v

About this documentAbout this document

Purpose

The purpose of this document is to provide hardware installation instructions for the

Alcatel-Lucent 9364 Metro Cell - Outdoor V2 2100MHz and 1900/850MHz products.

Procedures are provided for product handling, placement, grounding, powering on and

off, and cabling.

Reason for revision

The reissue reasons are:

Issue number Issue Date Reason for reissue

3 September 2011 Standard issue

2 May 2011 Standard issue

1 April 2011 Standard issue

New in this release

New features:

•None

Other changes:

•Information added in support of the 9364 Metro Cell 1900/850 MHz variant with

A-GPS

•Overcasing kit and installation instructions added

•Editorial updates

Intended audience

The audience for this document is Installation personnel.

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements vii

Supported systems

This document applies to the Alcatel-Lucent Metro Cell - Outdoor 2100MHz and

1900/850MHz.

How to use this document

Start with the first chapter and work through the manual to the end. Once you have done

this, you will have carried out the hardware installation completely and in the proper

sequence.

Prior to installing the product, the installer should be familiar with the safety precautions,

warnings, and product conformance statements.

Safety information

For your safety, this document contains safety statements. Safety statements are given at

points where risks of damage to personnel, equipment, and operation may exist. Failure to

follow the directions in a safety statement may result in serious consequences.

Prerequisites

None

Conventions used

Vocabulary conventions

None

Typographical conventions

None

Related information

For information on subjects related to the content of this document, refer to the

documents listed in the following table:

Refer to this document At this location For more information on

Alcatel-Lucent W-CDMA

System - Safety Guide,

401-382-880

http://support.alcatel-lucent.

com.

Safety guidelines and the

catalog of hazard statements

that appear in the

Alcatel-Lucent UMTS

customer documents.

About this document

....................................................................................................................................................................................................................................

viii Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Refer to this document At this location For more information on

Alcatel-Lucent 9364, Metro

Cell Outdoor

Troubleshooting,

401-387-076

http://support.alcatel-lucent.

com.

Troubleshooting procedures

for the 9364 Metro Cell

Outdoor

Standard for Installation of

Lightning Protection Systems,

NFPA

Lightning protection systems

Recommended Practices on

Surge Voltages in Low

Voltage AC Power Circuits,

IEEE C62.41 (Latest Edition)

Power

Document support

For support in using this or any other Alcatel-Lucent document, contact Alcatel-Lucent at

one of the following telephone numbers:

•1-888-582-3688 (for the United States)

•1-317-377-8618 (for all other countries)

Technical support

For technical support, contact your local Alcatel-Lucent customer support team. See the

Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact

information.

How to order

To order Alcatel-Lucent documents, contact your local sales representative or use Online

Customer Support (OLCS) (http://support.alcatel-lucent.com).

How to comment

To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-

lucent.com/comments/enus/) or e-mail your comments to the Comments Hotline

(comments@alcatel-lucent.com).

About this document

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements ix

11Safety statements

Overview

Purpose

This chapter provides general information on the structure of safety instructions and

summarizes general safety requirements.

General safety and residual risk

The equipment has been developed in line with state-of-the-art technology and conforms

with current national and international safety requirements.

The equipment is considered safe during normal operation when safe working practices

are complied with. However, hazards may arise if procedures are not followed correctly

or safe working practices are not complied with.

Contents

Structure of safety statements 1-2

Safety 1-4

Safety - specific hazards 1-5

Product safety 1-8

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 1-1

Structure of safety statements

Overview

Safety statements describe the safety risks relevant while performing tasks on

Alcatel-Lucent products during deployment and/or use. Failure to avoid the hazards may

have serious consequences.

General structure

Safety statements include the following structural elements:

Item Structure element Purpose

1 Safety alert symbol Indicates the potential for personal injury

(optional)

2 Safety symbol Indicates hazard type (optional)

3 Signal word Indicates the severity of the hazard

4 Hazard type Describes the source of the risk of damage or

injury

5 Safety message Consequences if protective measures fail

6 Avoidance message Protective measures to take to avoid the hazard

7 Identifier The reference ID of the safety statement

(optional)

SAMPLE

BC D

EF

G

H

Lifting this equipment by yourself can result in injury

due to the size and weight of the equipment.

Always use three people or a lifting device to transport

and position this equipment. [ABC123]

CAUTION

Lifting hazard

Safety statements Structure of safety statements

....................................................................................................................................................................................................................................

1-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Signal words

The signal words identify the hazard severity levels as follows:

Signal word Meaning

DANGER Indicates an extremely hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTION Indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

NOTICE Indicates a hazardous situation not related to personal injury.

Safety statements Structure of safety statements

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 1-3

Safety

General precautions for installation procedures

WARNING

Failure to observe these safety precautions may result in personal

injury or damage to equipment.

•Read and understand all instructions.

•Follow all warnings and instructions marked on this product.

•Installation and maintenance procedures must be followed and performed by

trained personnel only.

•The equipment must be provided with a readily accessible disconnect device

as part of site preparation.

•Grounding and circuit continuity is vital for safe operation of the equipment.

Never operate the equipment with grounding/bonding conductor

disconnected.

•Install only equipment identified in the product's installation manual. Use of

other equipment may result in an improper connection which could lead to

fire or injury.

•Use caution when installing or modifying telecommunications lines.

•The product has multiple power inputs. Before servicing, Disconnect all

inputs to reduce the risk of energy hazards.

•For continued protection against risk of fire, all fuses used in this product

must be replaced only with fuses of the same type and rating.

•Never install telecommunications wiring during a lightning storm.

•Never install telecommunications connections in wet locations.

•Never touch uninsulated wiring or terminals carrying direct current or

ringing current, and never leave this wiring exposed. Protect and tape

uninsulated wiring and terminals to avoid risk of fire, electrical shock, and

injury to personnel.

•Never spill liquids of any kind on the product.

•To reduce the risk of an electrical shock, do not disassemble the product.

Opening and removing covers and/or circuit boards may expose you to

dangerous voltages or other risks. Incorrect reassembly can cause electrical

shock when the unit is subsequently used.

Safety statements Safety

....................................................................................................................................................................................................................................

1-4 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Safety - specific hazards

DANGER

Electric-shock hazard

Working in severe weather can result in personal injury or death and damage to the

equipment.

Never install or perform maintenance during severe weather (high winds, lightning,

blizzards, hurricane etc.).

DANGER

Noxious-substance hazard

Use of unspecified cleaning agents can result in personal injury.

Use only specified cleaning agents. Never use flammable solvents.

Always ensure there is adequate ventilation in the work area and wear the appropriate

personal protective equipment.

CAUTION

RF hazard

RF exposure in excess of applicable limits can result in personal injury.

Metro Cells are designed and installed in order that they are compliant with the

international exposure guidelines laid down by the International Commission on

Non-Ionizing Radiation Protection (ICNIRP).

For all staff that are required to work in close proximity to the equipment, for example

maintenance personnel, contact with the antenna should be avoided.

WARNING

Electric-shock hazard

Some parts of all electrical installations are energized. Failure to observe this fact and

the safety warnings may lead to bodily injury and property damage.

For this reason, only trained and qualified personnel (electrical workers as defined in

IEC 60215 + A1 or EN 60215) may install or service the installation.

Safety statements Safety - specific hazards

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 1-5

WARNING

Electric-shock hazard

The power supply lines to the network element are energized. Contact with parts carrying

voltage can cause health problems, possibly including death, even hours after the event.

Open and lockout the load disconnect switch in the distribution box to completely

de-energize the network element.

WARNING

Electric-shock hazard

This product may be connected to an AC main power supply and may contain an internal

battery supply. Disconnecting one power source may not de-energize the system, and can

lead to serious injury.

Disconnect and lock out the AC main power supply, if present, and the internal battery

supply, if present, before servicing the equipment.

WARNING

Fall hazard

Falls can occur when working at heights resulting in serious personal injury or death.

To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe

work practices and wear appropriate fall protection equipment.

NOTICE

Condensation

Sudden changes in the weather may lead to the formation of condensation on

components. Operating the unit when condensation moisture is present can destroy the

unit.

Units which show signs of condensation must be dried before installation.

Safety statements Safety - specific hazards

....................................................................................................................................................................................................................................

1-6 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

NOTICE

Tools

Tools left in the working area can cause short circuits during operation which can lead to

the destruction of units.

Make sure after finishing your work that no tools, testing equipment, flashlights, etc.,

have been left in or on the equipment.

Safety statements Safety - specific hazards

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 1-7

Product safety

Equipment safety

Safety information for this equipment can be found on various Caution, Warning, Danger,

information labels or instructions affixed to or included with the cabinet, its internal

assemblies or included within this document. Informational and cautionary labels may

appear near the item they address or may be grouped in a single location on the

equipment. Warnings are typically adjacent to the hazard that is noted on the label. The

instructions, cautions and warnings found on these labels must be understood and

observed by all personnel involved with the equipment installation and maintenance.

Safety statements Product safety

....................................................................................................................................................................................................................................

1-8 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

22Product overview

Overview

Purpose

This chapter provides an overview of the Alcatel-Lucent 9364 Metro Cell Access Point -

Outdoor.

Contents

Functional description 2-2

Physical description 2-5

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 2-1

Functional description

General description

The 9360 Small Cell solution has been developed to handle the increased demand of

solutions to efficiently address the residential fixed and mobile market.

The Alcatel-Lucent 9364 Metro Cell - Outdoor is a public area wireless access node that

collapses the traditional 3G Node B and RNC functions into a single small unit.

Product deployment

The product can be deployed by mobile operators to provide a transparent outdoor

capacity layer to complement the macro cell “umbrella” coverage layer. In the case of

private locations, such as coffee shops or restaurants, the Metro Cell may be privately

owned and may be deployed by building owners or local governments but remain

controlled by the operator using their spectrum resources.

Figure 2-1 Alcatel-Lucent 9364 Metro Cell - Outdoor (with pole mounting bracket

attached)

Front view Back view

Product overview Functional description

....................................................................................................................................................................................................................................

2-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

V2 product description

Two variants for the Metro Cell - Outdoor are available:

•2100 MHz

•1900/850 MHz

Metro Cell - Outdoor 2100 MHz

This table lists the characteristics of the 2100 MHz variant.

Metro

Cell

Outdoor

Features

Frequency Power User

capacity

Characteristics

V2 Frequency Band:

2100 MHz

3G Sniffer

Frequency band:

900/2100 MHz

2G Sniffer

Frequency bands:

900/1800 MHz

Power is supplied by

the router or a PoE+

injector

Power consumption

is maximum 25W

and typically 20W

Supports up

to 32 users

with full

speed HSPA

(14.4 Mbps

L1 HSDPA

bearer and

5.7 Mbps

L1 HSUPA

bearer)

Supports Rx space

diversity

Maximum transmit

power of 250 mW at

antenna connector

(enabling wider cell

coverage)

Temperature range: -33

to +45 0C

Wall or pole mounted

installation options

Waterproof enclosure

with surge protection

Product overview Functional description

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 2-3

Metro Cell - Outdoor 1900/850 MHz

This table lists the characteristics of the 1900/850 MHz variant.

Metro

Cell

Outdoor

Features

Frequency Power User

capacity

Characteristics

V2 Frequency Band:

1900 and 850

MHz

3G Sniffer

Frequency band:

1900/850 MHz

2G Sniffer

Frequency bands:

1900/850 MHz

Power is supplied by

the router or a PoE+

injector

Power consumption

is maximum 25W

and typically 20W

Supports up

to 32 users

with full

speed HSPA

(14.4 Mbps

L1 HSDPA

bearer and

5.7 Mbps

L1 HSUPA

bearer)

Supports Rx space

diversity

Assisted GPS

capability for

localization of the unit

Maximum transmit

power of 250 mW at

antenna connector

(enabling wider cell

coverage)

Temperature range: -33

to +45 0C

Wall or pole mounted

installation options

Waterproof enclosure

with surge protection

Installation options

The Alcatel-Lucent 9364 Metro Cell - Outdoor is designed to be used outdoors can be

installed using the following options:

•pole mounted

•wall mounted

Product overview Functional description

....................................................................................................................................................................................................................................

2-4 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Physical description

Product overview

The Alcatel-Lucent 9364 Metro Cell - Outdoor is housed in an Alcatel-Lucent generic

metallic case with a pair of antenna connectors located at the top of the device for

external antennas, as shown below:

Note: The Alcatel-Lucent 9363 Metro Cell - Outdoor 1900/850 MHz variant interface

panel will have a SMA connector for external GPS antenna and additional LEDs.

Physical data

The physical characteristics of the Metro Cell - Outdoor (without the power supply unit)

are:

Dimensions (Height x Width x

Depth)

241 x 241 x 53 mm (9.48 x 9.48 x 2.08 in)

Weight <2.0 Kg (<4.4 lb)

Figure 2-2 Alcatel-Lucent 9364 Metro Cell - Outdoor (2100 MHz variant)

Antenna

RJ45 (PoE)

Port 1 Grounding

point

Reset

button

LEDs

Product overview Physical description

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 2-5

Connectors

Connectors provided are:

Connection location Description

At the top of the unit Two external antenna connectors, type N

At the bottom of the unit 1 Ethernet connector for backhauling connection: 10/100 Base

T RJ45 connector. This connector is connected to a PoE+

capable router or a PoE+ power injector in order to supply

power.

A ground connector.

SMA connector for external GPS antenna (1900/850 MHz

variant only)

Connectors provided are external and waterproof. They are also protected by surge and

lightning arrestor.

Power supply

The Metro Cell - Outdoor can be powered via:

•48V PoE+ (if supported)

•When the router is not 48V PoE+ capable, a power injector must be added to supply

power.

Product overview Physical description

....................................................................................................................................................................................................................................

2-6 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Antenna

The Metro Cell - Outdoor has two external RF antenna connectors, type N, located on the

top the device. The pair of antennas provide TX/RX and sniffing and enable Rx diversity

capability on the Metro Cell - Outdoor.

Debug interface

Three LEDs and a reset button are hidden behind a removable cover for debugging

purposes.

The LEDs provide status indication for:

•Power

•System

•Phone (Device)

The Alcatel-Lucent 9363 Metro Cell - Outdoor 1900/850 MHz variant will have

additional LEDs providing status indication for:

•GPS

Additional LEDs for Ethernet connectivity status are available at the Ethernet Port.

Product labelling

A product label provides the following information:

•Model name

•Part number

•serial number

•MAC address

•CE Approval marking

•Environmental marking (WEEE/ROHS) applicable to the device.

Product overview Physical description

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 2-7

Product base items

The Metro Cell - Outdoor product is delivered with the following base items:

•Metro Cell - Outdoor unit (with R2CT mini short plug)

•Pole/Wall mounting kit:

– 4 Torx Screw M5

– 4 flat washers

– Wall/Pole bracket

Note: Metro Cell - Outdoor unit can be supplied with or without a USIM card reader

(for authentication purposes).

Product configuration

In addition to the base items the Metro Cell - Outdoor can be configured with the

following variable and ancillary items:

•Antenna:

– +2dBi Omnidirectional

– +4dBi Omnidirectional

– +8dBi Omnidirectional (with relevant mounting kit)

•GPS Antenna with cable and support brackets (1900/850 MHz variant only)

•PoE+ injector

•A pair of RF jumpers (2 meters)

•Overcasing installation kit

Product overview Physical description

....................................................................................................................................................................................................................................

2-8 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

33Metro Cell installation and

commissioning

Overview

Purpose

This chapter provides the installation and commissioning procedures for

theAlcatel-Lucent 9364 Metro Cell Access Point - Outdoor.

Contents

Pre-installation information 3-2

To mount the hardware to a wall 3-4

To mount the hardware to a pole 3-8

Metro Cell - Outdoor cabling 3-11

Metro Cell - Outdoor commissioning process 3-16

Post installation activities and checks 3-17

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-1

Pre-installation information

Product delivery contents

The V2 Metro Cell - Outdoor is provided in a standard paper box. The contents are as

follows:

•The V2 Metro Cell - Outdoor access point

•R2CT mini short plug

•Pole/Wall mounting kit (excluding collar kit)

Variable parts and ancillary items

In addition to the standard delivered parts the following variable and ancillary items are

available:

•Antennas:

– 2dBi omni directional antenna

– 4dBi omni directional antenna

– 8dBi omni directional antenna with mounting kit

•External GPS antenna with 1.48 feet (450 mm) of cable (1900/850 MHz variant only)

•RF jumper, 2 meters

•A PoE+ power injector, with user guide

•Pole mounting collar kit

Device placement

The V2 Metro Cell - Outdoor emits a radio signal similar to a Wi-Fi router. The quality of

coverage achieved therefore depends upon where the device is placed.

For best results it should be located:

•In a central place within the public space

•As high as possible, for example, high shelving, wall mounted

To improve coverage, avoid installing near the following:

•Other radio transmitters

•Other metallic devices or objects

•Windows

Tip: In order to limit the amount of solar radiation on the Metro Cell when the device

is pole mounted, it is recommended to orientate the Metro Cell in a northerly

direction. With this orientation the pole mounting bracket acts as a solar shield.

Metro Cell installation and commissioning Pre-installation information

....................................................................................................................................................................................................................................

3-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Installation tools required

The following is a list of the tools that may be used during installation:

•Drill and assorted drill bits

•Pliers

•Adjustable spanners

•Screwdrivers (power and/or manual):

– Phillips (flat blade)

– Torx, T-10, T-20

•Crimping tool (for RJ45 cable)

•Measuring tape

•Marker, to mark wall mounting holes

•Vacuum cleaner or equivalent (required for clearing debris from wall mounting holes)

•Spirit level

Metro Cell installation and commissioning Pre-installation information

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-3

To mount the hardware to a wall

Purpose

This topic describes the procedures to be followed when installing the Metro Cell -

Outdoor onto a solid concrete wall.

Prerequisites

A site survey has been conducted and a location for the device has been selected that is

both central to the public space and elevated in order to maximize coverage.

Before installation begins you should ensure the following are in place:

•Internet service is available.

•The Ethernet cable has been routed and is in place.

•The Ground cable has been routed and is in place.

•Site specific fixing materials (screws, washers, wall plugs) for wall mounting the

Metro Cell - Outdoor.

Wall mounting

Important! The Metro Cell - Outdoor weighs less than 2kg and can be easily

mounted onto any flat, sturdy wall, either directly, or by using the wall mounting kit

(in circumstances where the device needs to by mounted away from the wall).

However, various building materials and construction methods dictate that the device

be fastened to the wall with appropriate mounting hardware. It is the responsibility of

the customer to provide any necessary support material and structures to ensure that

the installation will be in compliance with Building Officials and Code Administrators

(BOCA), Uniform Building Code (UBC), and all local codes.

Before you begin

Note: Record the 11 digit serial number before mounting the Metro Cell - Outdoor.

If the Metro Cell overcasing is to be installed, attach the overcasing support plate before

wall mounting, see Appendix A, “Overcasing installation”

Metro Cell installation and commissioning To mount the hardware to a wall

....................................................................................................................................................................................................................................

3-4 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Wall mount installation

WARNING

Fall hazard

Falls can occur when working at heights resulting in serious personal injury or death.

To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe

work practices and wear appropriate fall protection equipment.

To mount the device onto a wall or flat surface perform the following steps.

...................................................................................................................................................................................................

1At the selected installation location:

If.. Then..

the Metro Cell is to be mounted directly onto a

wall

mark the points on the wall for the four fixing

holes using the template in Appendix B,

“Metro Cell wall mount spacer” as a guide.

the Metro Cell is to be mounted onto a wall

using the wall mounting kit

use the wall mounting bracket as a guide to

mark the points on the wall for the four

bracket fixing holes.

...................................................................................................................................................................................................

2Check the horizontal position of the marked holes with a spirit level.

...................................................................................................................................................................................................

3Drill holes at the marked points and insert wall plugs into the fixing holes.

...................................................................................................................................................................................................

4

If.. Then..

The Metro Cell is to be mounted directly onto

a wall

Proceed with the next Step

The Metro Cell is to be mounted onto a wall

using the wall mounting kit

Attach the wall mounting bracket to the wall

using appropriate screw fixings.

Note: Depending on the wall the device is to

be mounted onto, different screw fixings might

be needed. After site survey these mounting

accessories must be procured locally.

Metro Cell installation and commissioning To mount the hardware to a wall

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-5

...................................................................................................................................................................................................

5Using the lifting point on the device align the bolt holes on the Metro Cell with the drilled

wall bolt holes or, if the wall mounting bracket is used, with the bolt holes on the bracket:

...................................................................................................................................................................................................

6Attach the device to the wall mounting bracket using the supplied screws or directly onto

the wall using appropriate screw fixings.

Note: Depending on the wall the device is to be mounted onto, different screw fixings

might be needed. After site survey these mounting accessories must be procured

locally.

Bolt holes

(8mm)

Bolt holes

(8mm)

Lifting point

Metro Cell installation and commissioning To mount the hardware to a wall

....................................................................................................................................................................................................................................

3-6 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

...................................................................................................................................................................................................

7After mounting the Metro Cell - Outdoor to the wall the cables must be connected.

Continue with, “Metro Cell - Outdoor cabling” (p. 3-11).

Device attach

points

Device attach

points

Metro Cell installation and commissioning To mount the hardware to a wall

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-7

END OF STEPS

...................................................................................................................................................................................................

To mount the hardware to a pole

Purpose

This topic describes the procedures to be followed when installing the Metro Cell -

Outdoor onto a pole.

Prerequisites

A site survey has been conducted and a location for the device has been selected that is

both central to the public space and elevated in order to maximize coverage.

Before installation begins you should ensure the following are in place:

•Internet service is available.

•The Ethernet cable has been routed and is in place.

•The Ground cable has been routed and is in place.

Pole mounting

Important! The Metro Cell - Outdoor is less than 2kg and can be easily mounted on a

pole (48mm to 114mm in diameter) using the supplied pole mounting kit.

Before you begin

Note: Record the 11 digit serial number before mounting the Metro Cell - Outdoor.

If the Metro Cell overcasing is to be installed, attach the overcasing support plate before

wall mounting, see Appendix A, “Overcasing installation”

Pole mount installation

WARNING

Fall hazard

Falls can occur when working at heights resulting in serious personal injury or death.

To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe

work practices and wear appropriate fall protection equipment.

To mount the device onto a pole perform the following steps.

...................................................................................................................................................................................................

1Using the supplied pole bracket thread metal pole bands through the pole channel groove

on the pole bracket.

Metro Cell installation and commissioning To mount the hardware to a pole

....................................................................................................................................................................................................................................

3-8 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Recommended pole band clips, 16mm stainless steel of type:

•Jubilee®High Torque

•JCS HI-Torque or Tamtorque®

...................................................................................................................................................................................................

2At the selected installation location assemble the bracket onto the pole as shown, ensuring

the bracket metal bands are securely tightened. Recommended torque setting: 15 N.m

...................................................................................................................................................................................................

3Using the lifting point on the device align the bolt holes on the Metro Cell with the pole

bracket bolt holes:

Bolt holes

(8mm)

Bolt holes

(8mm)

Lifting point

Metro Cell installation and commissioning To mount the hardware to a pole

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-9

...................................................................................................................................................................................................

4Use the following installation materials to bolt the Metro Cell to the pole bracket:

•4 x Screw (M5x25)

•4 x Washer (5.2mm)

...................................................................................................................................................................................................

5After mounting the Metro Cell - Outdoor to the pole the cables need to be connected.

Continue with, “Metro Cell - Outdoor cabling” (p. 3-11).

Device attach points

Metro Cell installation and commissioning To mount the hardware to a pole

....................................................................................................................................................................................................................................

3-10 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

END OF STEPS

...................................................................................................................................................................................................

Metro Cell - Outdoor cabling

Purpose

This topic describes the procedures to be followed when connecting the Metro Cell -

Outdoor cables.

Before you begin

Connect the pair of omni-directional antenna to the antenna connectors on the device.

Important! It is recommended that the antenna connection nuts are torqued to

between 0,7 N.m minimum and 1,1 N.m maximum in order to avoid a potential loose

connection.

Connect the ground cable

Note: The Metro Cell Outdoor has to be grounded with a 16 mm² ground cable (Type

NYY-1x16mm² or similar) to a grounding system.

The grounding cable and cable lug are not included in delivery and must be locally

supplied.

To attach the ground cable perform the following steps.

...................................................................................................................................................................................................

1Route the ground cable from the ground system to the Metro Cell - Outdoor.

Antenna

Connectors

(N female)

Metro Cell installation and commissioning Metro Cell - Outdoor cabling

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-11

...................................................................................................................................................................................................

2At the Metro Cell - Outdoor cut the cable to a proper length, strip the cable end and crimp

a ground lug, with a hole suitable for an M6 screw, on the end of the cable.

Clean the contact surface area and use antioxidant to avoid oxidation.

...................................................................................................................................................................................................

3Connect the ground cable to the grounding point on the Metro Cell - Outdoor.

...................................................................................................................................................................................................

4Finally, secure grounding cable to the wall/pole.

Ethernet cable lengths

The following diagram outlines the maximum cable length of the Metro Cell- Outdoor

ethernet cable connection.

Grounding

Point

Metro Cell installation and commissioning Metro Cell - Outdoor cabling

....................................................................................................................................................................................................................................

3-12 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

END OF STEPS

...................................................................................................................................................................................................

Connect the Ethernet cable

To attach the Ethernet cable perform the following steps.

...................................................................................................................................................................................................

1Route the supplied Ethernet cable from the Metro Cell - Outdoor to the router or 48V

PoE+ injector.

...................................................................................................................................................................................................

2At the Metro Cell - Outdoor, assemble the supplied R2CT mini short plug onto the

ethernet cable following the R2CT mating sequence assembly instructions.

...................................................................................................................................................................................................

3Connect the Ethernet cable to the device as shown.

Metro Cell - Outdoor DSL Router with

PoE+ function

Ethernet Cable

Total cable length 100m max

Metro Cell - Outdoor DSL Router with

PoE+ function

Ethernet Cable

Total cable length 100m max

PoE+ Power

Injector

Ethernet connection

point

Metro Cell installation and commissioning Metro Cell - Outdoor cabling

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-13

Important! It is recommended that the Ethernet cable screw nut is torqued to between

3 N.m minimum and 3,5 N.m maximum in order to avoid a potential loose

connection.

...................................................................................................................................................................................................

4At the Router/PoE+ injector cut the cable to the required length and crimp the supplied

RJ45 connector onto the end of the cable.

...................................................................................................................................................................................................

5Connect the Ethernet cable to the Router/PoE+ injector.

...................................................................................................................................................................................................

6Finally, secure Ethernet cable to the wall/pole.

A-GPS antenna cable connection (1900/850 MHz only)

The Alcatel-Lucent 9364 Metro Cell - Outdoor 1900/850 MHz has Assisted GPS

capability for localization of the unit.

An SMA connector is provided for the connection of an external GPS antenna.

The GPS antenna cable can be routed around the back of the unit and, using the GPS

antenna bracket and support plate, attached to the Metro Cell as shown.

GPS Antenna

connector

Metro Cell installation and commissioning Metro Cell - Outdoor cabling

....................................................................................................................................................................................................................................

3-14 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

END OF STEPS

...................................................................................................................................................................................................

Power supply

Power is supplied to the Metro Cell - Outdoor using 48V PoE+ (Power over Ethernet).

The PoE+ is supplied through the Ethernet cable connection. This Ethernet cable has to

be connected to a PoE+ capable router or to the supplied 48V DC Power Injector.

If no PoE+ capable router is available, the 48V DC Power Injector has to be installed

between the router and the Metro Cell Outdoor.

For installation instructions, refer to the user guide located in the Power Injector box,

document number 06-0062-056.

How to continue

After antenna and cable connections are completed continue onto, “To commission the

Metro Cell - Outdoor”.

Antenna support

bracket

Antenna support

plate

Assembled view with

support plate and bracket

Metro Cell installation and commissioning Metro Cell - Outdoor cabling

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-15

Metro Cell - Outdoor commissioning process

Purpose

This section describes the Metro Cell - Outdoor commissioning process. The Metro Cell -

Outdoor is self commissioning in the case of single device deployments. Where multiple

device deployments occur the operator may compliment zero-touch commissioning with

appropriate cell planning.

Troubleshooting

If any problems occur during the commissioning process refer to the following document:

•Alcatel -Lucent 9364 Metro Cell - Indoor and Outdoor Troubleshooting, 401-387-076.

Commissioning process

The following steps outline the zero-touch commissioning process.

...................................................................................................................................................................................................

1Power on the Metro Cell - Outdoor. After 1-3 seconds the power supply status indicator

will light up and the Ethernet port status indicator will flash green.

...................................................................................................................................................................................................

2After approximately 2 minutes the 9363 Metro Cell will initialize and establish

connectivity. During this operation the System status indicator will blink slowly.

...................................................................................................................................................................................................

3After the device has established a network connection the 9364 Metro Cell will

automatically update it's software. This process takes approximately 15 minutes. During

this operation both the System and Phone (device) indicators will blink.

...................................................................................................................................................................................................

4Once the software update has completed the 9364 Metro Cell will carry out an automatic

reboot. During reboot the Power and System indicators will be on.

...................................................................................................................................................................................................

5After rebooting the device will automatically auto-configure itself. During this operation

the System status indicator will blink slowly.

...................................................................................................................................................................................................

6When the device is ready for use the Power, System and Phone (device) status indicators

will all be ON.

Metro Cell installation and commissioning Metro Cell - Outdoor commissioning process

....................................................................................................................................................................................................................................

3-16 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

END OF STEPS

...................................................................................................................................................................................................

Post installation activities and checks

Faceplate attachment

Once the Metro Cell is commissioned and ready for use attach the faceplate cover:

...................................................................................................................................................................................................

1Check all cable connections are secure and correctly routed.

...................................................................................................................................................................................................

2Using the supplied four faceplate screws, connect the faceplate to the device:

Metro Cell installation and commissioning Post installation activities and checks

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 3-17

END OF STEPS

...................................................................................................................................................................................................

Final installation checks

Before leaving the installation site, check the following:

...................................................................................................................................................................................................

1Secure all cables along their routes.

...................................................................................................................................................................................................

2Verify that all the exterior conduit and cable connections are secure.

...................................................................................................................................................................................................

3Inspect the site for loose tools, materials, and parts. Remove all such loose tools,

materials, and parts.

Metro Cell installation and commissioning Post installation activities and checks

....................................................................................................................................................................................................................................

3-18 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

END OF STEPS

...................................................................................................................................................................................................

44Product specifications

Overview

Purpose

This chapter details the Alcatel-Lucent 9364 Metro Cell - Outdoor product environmental

specifications.

Contents

Environmental and regulatory specifications 4-2

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements 4-1

Environmental and regulatory specifications

Overview

The Metro Cell - Outdoor is CE certified and is compliant to RoHS and WEEE as well as

the standards listed in the following sections.

Environmental operating conditions

Metro Cell - Outdoor operating temperature range: -33° to +45°.

The Metro Cell - Outdoor is compliant to the following environmental operating

standards:

•ETS300 019 class 4.1 (temperature range: -33° to +55°), “Non-weather protected

locations”

Health, safety, and environmental standards

The Metro Cell - Outdoor is compliant with the following health, safety, and

environmental standards:

•IEC 60950-1 (International)

•EN 50383, EN 50385

•Directive 2002/95/EC RoHS6.

•Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE)

EMC (Electromagnetic Compatibility)

The Metro Cell - Outdoor product complies with the following EMC emission and

immunity requirements:

•ETSI EN 301 489-1

•ETSI EN 301 489-23

•ETSI EN 301 908-1

•ETSI EN 301 908-3

The Metro Cell - Outdoor product complies with the following standards:

•3GPP TS 25.113 Rel 8

Product specifications Environmental and regulatory specifications

....................................................................................................................................................................................................................................

4-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Appendix A: Overcasing

installation

Overview

Purpose

This section provides the instructions for installing the overcasing applicable to the

Alcatel-Lucent 9364 Metro Cell - Outdoor V2 2100 MHz and 1900/850 MHz.

Contents

Overcasing installation instructions A-2

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements A-1

Overcasing installation instructions

Overcasing installation kit

•Overcasing cover

•Overcasing retention screws

•Overcasing support plate

•Overcasing support plate fixing screws

Installation steps

...................................................................................................................................................................................................

1Before carrying out wall or pole mounting of the Metro cell attach the overcasing support

plate to the reverse side of the unit using the supplied screws.

Overcasing cover

Overcasing

support plate

Overcasing installation Overcasing installation instructions

....................................................................................................................................................................................................................................

A-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

...................................................................................................................................................................................................

2Install the Metro Cell at the desired location

•“To mount the hardware to a wall” (p. 3-4)

•“To mount the hardware to a pole” (p. 3-8)

...................................................................................................................................................................................................

3Prior to attaching the overcasing route cables either through the back of the overcasing

support plate or through the bottom of the overcasing and secure the cables.

...................................................................................................................................................................................................

4Attach the overcasing to the top of the Metro Cell unit and secure in place using the two

retention screws at the bottom of the overcasing.

Overcasing support

bracket attachment

GPS Antenna

cable

Ethernet

cable

Overcasing installation Overcasing installation instructions

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements A-3

Overcasing

retention screws

Overcasing attachment

(top of unit)

Overcasing installation Overcasing installation instructions

....................................................................................................................................................................................................................................

A-4 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

END OF STEPS

...................................................................................................................................................................................................

Appendix B: Metro Cell wall

mount spacer

Overview

Purpose

This section details the hole spacing to be drilled when the Metro Cell unit is mounted

onto a wall or flat surface.

Contents

Wall mount spacer B-2

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements B-1

Wall mount spacer

Spacer template

1

2

34

218mm

Not to scale

Wall drill position for screws

(Note: Use screws suitable for a 8mm bolt hole)

Max tightening torque: 3 Nm

Washer (serial large) are advised

Metro Cell wall mount spacer Wall mount spacer

....................................................................................................................................................................................................................................

B-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Appendix C: Product

conformance statements

Overview

Purpose

This section presents the product conformance statements that apply to the Alcatel-Lucent

Metro Cell Access Point equipment.

The statements that are required are determined primarily by national or multi-national

regulations. However, in some regions, contract terms determine which statements are

required.

The presence of the statement indicates that the product does comply with that statement

wherever it is required to do so.

Contents

European Union C-2

...................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements C-1

European Union

Introduction

The statements that follow are the product conformance statements that apply to the

Alcatel-Lucent Metro Cell Access Point equipment when deployed in the European

Union.

Declaration of Conformity for radio and telecommunication terminal equipment

under the scope of Directive 1999/5/EC.

Hereby, Alcatel-Lucent declares that the equipment documented in this publication is in

compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC.

The technical documentation as required by the Conformity Assessment procedure is kept

at the Alcatel-Lucent location which is responsible for this product. For more information

please contact your local Alcatel-Lucent Customer Service Organization.

CE marking

This product has been CE-marked in accordance with the following European Directives:

•1999/05/EC Radio and Telecommunication Terminal Equipment (R&TTE)

EMC compliance

The equipment complies with the following EMC specifications:

Standard reference Title

EN 301 489 V1.8.1/-23 V1.3.1 Electromagnetic Compatibility (Article 3.1(b)

of the R&TTE Directive)

EN 55022:2006/A1:2007 Class B EMC Directive (2004/108/EC)

EN 55024:1998/A1:2001/A2:2003 EMC Directive (2004/108/EC)

Product conformance statements European Union

....................................................................................................................................................................................................................................

C-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Radio spectrum compliance

The equipment complies with the following radio spectrum specifications:

Standard reference Title

EN 301 908-1/-3 V3.2.1 Radio Frequency Spectrum usage (Article 3.2

of the R&TTE Directive)

Product safety

The equipment complies with the following product safety specifications:

Standard reference Title

EN 60950-1:2006+A11:2009 Safety (Article 3.1(a) of the R&TTE Directive)

EN 50385:2002 Health (Article 3.1(a) of the R&TTE Directive)

EN 50383:2002 Health (Article 3.1(a) of the R&TTE Directive)

Antenna exposure

Antenna attachment for the Alcatel-Lucent 9364 Metro Cell Access Point equipment shall

be performed in accordance with all applicable manufacturer's recommendations, and

national laws and regulations. To ensure correct antenna installation, the antenna installer

shall perform all necessary calculations and/or field measurements to evaluate compliance

with applicable national laws or regulations regarding exposure to electromagnetic fields.

The supplier of radio equipment, the supplier of antenna equipment and the integrator and

builder of the site must provide sufficient information so that the limits of the exclusion

zones can be determined. Any changes to the antenna or other equipment in the transmit

path may require re-evaluation of the exposures to electromagnetic fields.

Pursuant to:

•European Council Recommendation 1999/519/EC, “On the limitation of exposure of

the general public to electromagnetic fields”

•ICNIRP (International Commission on Non-Ionising Radiation Protection),

“Guidelines for limiting exposure to time-varying electric, magnetic, and

electromagnetic fields”

All installations must be evaluated against the Reference Levels, and if necessary

exclusion zones for public and installation workers defined. For staff that are required to

work in close proximity to the equipment, for example maintenance personnel, contact

with the antenna should be avoided.

Product conformance statements European Union

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements C-3

The following information on Alcatel-Lucent supplied equipment is available from

customer representatives:

•Output power and antenna characteristic, if the product is equipped with an integral

antenna

•A detailed description of at least one typical normal configuration, including antenna

system (feeders, connectors, combiners, antennas, etc.), if the product is intended to

be used with external antennas

•Limit distances for general public and occupational exposure. If the product is

intended for use with external antennas, limit distances shall be given for the given

typical system configurations.

•Information on how to specify exposure levels and limit distances for any optional

system configuration not specified in detail

•Information on how to install the equipment/system or the external antennas in order

to ensure that the separation between the radiating antenna and general public are

exceeding the maximum allowed distances

Information on the methodology used for the determination of RF safety compliance

distances and exclusion zones, and the results of the compliance evaluation shall be

available for inspection by officials of the governing authorities.

Packaging collection and recovery requirements

Countries, states, localities, or other jurisdictions may require that systems be established

for the return and/or collection of packaging waste from the consumer, or other end user,

or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the

return and/or collection of the packaging waste may be established. For more information

regarding collection and recovery of packaging and packaging waste within specific

jurisdictions, contact the Alcatel-Lucent Environment, Health and Safety organization.

Recycling / take-back / disposal of products and batteries

In compliance with Waste Electrical and Electronic Equipment Directive (WEEE

Directive) 2002/96/EC 01/2003, amended by WEEE Directive 2003/108/EC 12/2003,

electronic products and batteries bearing or referencing the symbols shown below shall be

collected and treated at the end of their useful life, in compliance with applicable

European Union and other local legislation. They shall not be disposed of as part of

unsorted municipal waste. Due to materials that may be contained in the product and

batteries, such as heavy metals, the environment and human health may be negatively

impacted as a result of inappropriate disposal.

Note 1: For electronic products put on the market in the European Union, a solid bar

under the crossed-out wheeled bin indicates that the product was put on the market after

13 August 2005.

Product conformance statements European Union

....................................................................................................................................................................................................................................

C-4 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Note 2: For batteries put on the market in the European Union, a chemical symbol Hg

(mercury), Cd (cadmium), or Pb (lead), or a combination of those symbols, beneath the

cross-out wheeled bin indicates that the battery contains the corresponding heavy metals.

Moreover, in compliance with legal requirements and contractual agreements, where

applicable, Alcatel-Lucent will offer to provide for the collection and treatment of

Alcatel-Lucent products bearing the logo at the end of their useful life, or products

displaced by Alcatel-Lucent equipment offers.

For information regarding take-back of equipment by Alcatel-Lucent, or for more

information regarding the requirements for recycling/disposal of a product, please contact

your Alcatel-Lucent account manager. Visit the Alcatel-Lucent Take-Back

(http://www.alcatel-lucent.com/product_takeback) web page, or contact Alcatel-Lucent

Takeback Support at (mailto:takeback@alcatel-lucent.com). For technical information on

product treatment, consult the Alcatel-Lucent Recycling Information (http://www.

alcatel-lucent.com/product_recycling) web page.

Material content compliance

Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003

on the restriction of the use of certain hazardous substances in electrical and electronic

equipment (RoHS Directive) restricts the use of lead, mercury, cadmium, hexavalent

chromium, and certain flame retardants in electrical and electronic equipment. This

Directive applies to electrical and electronic products placed on the EU market after 1

July 2006, with various exemptions, including an exemption for lead solder in network

infrastructure equipment. Alcatel-Lucent products shipped to the EU after 1 July 2006

comply with the EU RoHS Directive.

Product conformance statements European Union

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements C-5

Product conformance statements European Union

....................................................................................................................................................................................................................................

C-6 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Glossary

...................................................................................................................................................................................................................................

Numerics

2G

Second-Generation Mobile Network

3G

Third-Generation Mobile Network

3GPP

Third-Generation Partnership Project

...................................................................................................................................................................................................................................

B BOAC

Building Officials and Code Administrators

...................................................................................................................................................................................................................................

E ETSI

European Telecommunications Standards Institute

...................................................................................................................................................................................................................................

H HSUPA

High Speed Uplink Packet Access

...................................................................................................................................................................................................................................

KKg

kilogram

...................................................................................................................................................................................................................................

M MAC

Media Access Control.

A protocol that determines how devices will share resources on a local area network.

Mbps

Megabits per second

...................................................................................................................................................................................................................................

N NEMA

National Electrical Manufacturers Association.

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements GL-1

Node B

Logical Node for radio Tx/Rx in one or more cells to/from UE.

...................................................................................................................................................................................................................................

PPoE

Power over Ethernet

...................................................................................................................................................................................................................................

R RNC

Radio Network Controller

RoHS

Restriction of Hazardous Substances Directive

...................................................................................................................................................................................................................................

U UBC

Uniform Building Code

...................................................................................................................................................................................................................................

W WEEE

Waste Electrical and Electronic Equipment Directive

Glossary

....................................................................................................................................................................................................................................

GL-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Index

Aadditional optional items

Metro Cell - Outdoor, 3-2

antenna

Metro Cell - Outdoor, 2-7

.............................................................

Ccabling

Metro Cell - Outdoor, 3-11

characteristics

Metro Cell - Outdoor 1900/850

MHz, 2-4

Metro Cell - Outdoor 2100

MHz, 2-3

commission

Metro Cell - Outdoor, 3-16

connectors

Metro Cell - Outdoor, 2-6

.............................................................

Ddevice placement

Metro Cell - Outdoor, 3-2

.............................................................

Eenvironmental

specifications, 4-2

.............................................................

Ffunctional description

Metro Cell - Outdoor, 2-2

.............................................................

IInstallation options

Metro Cell - Outdoor, 2-4

installation, overcasing

Metro Cell - Outdoor, A-1

installation, pole mounted

Metro Cell - Outdoor, 3-8

installation, wall mounted

Metro Cell - Outdoor, 3-4

.............................................................

MMetro Cell - Ourdoor

tools, 3-3

Metro Cell - Outdoor

additional optional items, 3-2

antenna, 2-7

cabling, 3-11

commission, 3-16

connectors, 2-6

device placement, 3-2

functional description, 2-2

installation options, 2-4

installation, overcasing, A-1

installation, pole mounted, 3-8

installation, wall mounted, 3-4

physical data, 2-5

physical description, 2-5

post installation checks, 3-17

power supply, 2-6

pre-installation, 3-2

product delivery contents, 3-2

product labelling, 2-7,2-7

Metro Cell - Outdoor 1900/850

MHz

characteristics, 2-4

Metro Cell - Outdoor 2100 MHz

characteristics, 2-3

.............................................................

Pphysical data

Metro Cell - Outdoor, 2-5

physical description

Metro Cell - Outdoor, 2-5

post installation checks

Metro Cell - Outdoor, 3-17

power supply

Metro Cell - Outdoor, 2-6

pre-installation

Metro Cell - Outdoor, 3-2

product delivery contents

Metro Cell - Outdoor, 3-2

product labelling

Metro Cell - Outdoor, 2-7,2-7

....................................................................................................................................................................................................................................

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements IN-1

.............................................................

Rregulatory

specifications, 4-2

.............................................................

Sspecifications

environmental, 4-2

regulatory, 4-2

standards

electromagnetic compatibility,

4-2

environmental operating

conditions, 4-2

human safety, 4-2

.............................................................

Ttools

Metro Cell - Outdoor, 3-3

Index

....................................................................................................................................................................................................................................

IN-2 Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

Alcatel-Lucent 9364 MC

401-387-095

Issue 3 September 2011

Alcatel Lucent France MO-V2-250MW-DB 9364 Metro Cell Outdoor V2.0 1900/850MHz 250Mw User Manual USERS MANUAL 1

Alcatel-Lucent France 9364 Metro Cell Outdoor V2.0 1900/850MHz 250Mw USERS MANUAL 1

Contents

USERS MANUAL 1

Navigation menu

Namespaces

Views

Navigation